CWE/P-43/2019-20 SPECIAL REPAIR TO BLDGS NO NP-13 AND NP-14 OTM ACCN UNDER GE (SOUTH) PATHANKOT

Amount

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified and as directed.

M&L 50 mm thick cement concrete (1:2:4), type B-1 using 20mm graded stone aggregate as in plinth protection etc. and laid in alternate bays complete and finished the even & fair and providings joints through out the thickness of plinth protection filed with mastic filling comprising one part of 01 bitumen 85/25 grade and three part of sand by weight all as specified and directed.

Demolition of brick or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work, complete all as specified and directed.

M&L brick work with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius, built in cement mortar 1:6, complete all as specified and directed.

Description all as per item No.4.00 above, but except bricks, all as specified and directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frames) area not exceeding 1.5 Sqm each including taking out hold fast complete all as specified.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exceeding 1.5Sqm and not exceeding 4Sqm each including taking out hold fast complete all as specified and directed.

M&L Steel window/ Ventilator factory made out of M S tubular frame with double shutter with sash bar made out of section using flash butt welding, hinges (ISI marked) shall be provided to both shutters with fittings complete and one shop coat of red oxide primer all as per drg No CEPZ/TD/245/01 Sh 1/1, CEPZ-TD/246/01 Sheet 1/2 and Sheet 2/2 all as specified and directed by Engr-in-Charge. Note: (i) Cutting holes for hold fast making good in cement mortar 1:3 and PCC 1:2:4, type B-1 shall be included in the quoted rates. (ii) Grills/Gaurd bar shall be measured and paid separetely

Preparation new steel surfaces of any description not otherwise described, over 10cm width or girth and applying two coat of synthetic enamel paint complete all as specified.

M & L 3 mm thick sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm in each pane complete all as specified.

M & L galvanised mild steel wire cloth 0.56 nominal dia of wire and average width of aparture 1.18mm and fixed with tinned tacks or galvanised wire staples, complete all as specified.

M & L framed work such as grills, grating etc with ends of bars shouldered and or riveted, or forged into spikes, framed guard bars, barrel, iron doors, ladders, balusters, walkway, frame work of water tanks and similar work confirming to Fe-290 Gde E-165 complete all as specified.

Preparation old treated steel surfaces of any description not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified.

Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and directed as shown on drawing (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life)

S&F factory made Solid Panel prelam PVC door shutters 30 mm thick (style) consisting of frame made out of MS tubes of 19 guage thickness and size of 40mmx20mm for stiles as well as top, lock and bottom rails. MS frame shall have a coat of metal primer of approved make. M S frame shall be covered with heat moulded prelam PVC ‘C’ channel made of 5mm thick PVC sheet of density 600kg/cum manufactured by an ISO-9001-2008 certified company, of thickness 110mm width forming stiles in which 100mm should be flat and 5mm should be taper and 5mm thick, 135mmwide PVC sheet for top rail and bottom rail in which 125mm should be flat and 5mm should be tapper on either side of panel. also for the lock rail 145mm sheet , 125mmshould be flat and 5mm tapper on either side. an additional 5mm thick PVC strip of 20mm width is to be stuck on inner side of C chanel using PVC solvent cement adhesive. Panelling of 10mm Prelam PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with 30mm wide x 5mm thick PVC sheet beadings on either side and additional 30mm wide PVC beading as gap insert bellow top and bottom rails complete all as specified and directed.

M&L 1.25mm thick pressed steel frames with one shop coat of red oxide primer 105 x 60 mm with one or more rebates including necessary fixing lugs/hold fast duly tarred with bitumen and sanding with sharp clean sand, hinges (ISI marked), lock strike plate, including cement concrete type C-1, 1:3:6 (using 20 mm graded stone aggregate) as in filling hollow of frame with plain cement concrete and hold fast after taaring of hollow portion of frame complete all as specified and directed.

M&L 1.25mm thick pressed steel frames with one shop coat of red oxide primer 125 x 60 mm with one or more rebates including necessary fixing lugs/hold fast duly tarred with bitumen and sanding with sharp clean sand, hinges (ISI marked), lock strike plate, including cement concrete type C-1, 1:3:6 (using 20 mm graded stone aggregate) as in filling hollow of frame with plain cement concrete and hold fast after tarring of hollow portion of frame complete all as specified and directed

M&L Plain framed factory made 35mm thick shutter of 2nd class hard wood rail & style (two panel) with lock rail and panel of 9mm BWP commercial plywood or 12 mm veneered particle board with commercial veneering on both faces , the size of rail and style as per IS 1003 (Part-1) kiln seasoned and pressure treated all as specified.

M&L factory made Glazed and skelton shutters 35mm thick of 2nd class hard wood rail & style open rebated and prepared to receive glass or wire gauze etc. shutters (without shash bars), size of members of shutters as specified in SSR Part-1, secton 8, clause 8.24(a) kiln seasoned and pressure treated all as specified.

M&L anodized aluminum door powder coated with shutter vertical member of size 47.62x44.45x1.18 mm, bottom member 114.3x44.5x1.18 mm lock rail 63.5x44.45x2.4 mm and frame size 101.6x44.45x1.18 mm with and including providing and fixing 2 Nos aluminum door handles of 150 mm size to each shutter, tower bolts 200 mm size floor door spring/door closer , 5.5 mm thick tinted glass/bakelite sheet and cylindrical lock including neospreme lining complete all as specified and directed.

M&L anodized aluminum window powder coated with side hung shutter vertical member of size 47.62x44.45x1.18 mm,frame size 101.6x44.45x1.18 mm with and including providing and fixing 2 Nos aluminum door handles 150 mm size to each shutter, tower bolts 150 mm size 2 Nos Aluminum hinges 100 mm size to each shutter , 5.5 mm thick tinted sheet glass and neospreme lining complete all as specified and directed.

M & L preparation new wooden surfaces of any description not otherwise described, over 10cm width or girth and applying two coat of synthetic enamel paint of colour as approved by GE over a coat of pink primer complete all as specified.

M & L second class hard wood small fittings such as brakets of any type, latch and hinges blocks, shaped doors and windows stops and the like, including all necessary labour, articles not exceeding 200 cu.cm each complete all as specified

M & L 250 mm long aluminium alloy anodized sliding door (bolt type) (ISI marked) and fixing clips of sheets, cast of extrusted sections and fixing bolts and sliding bolts of extruded section of cast aluminium alloy all as specified.

M & L Mild steel butt hinges, medium weight, cold rolled (ISI marked),100mm long , complete all as specified.

M & L Aluminium alloy handles (ISI marked), cast type, anodised of size 150mm and fixed, complete all as specified and directed.

Supply and fxing Aluminium anodised, barrel tower bolts of extruded section of size 150mm ISI marked and fixed, complete all as specified and directed.

Supply and fxing , 150mm mild steel helical door springs including roller and roller plate (ISI marked) complete including all neccesary welding if required all as specified.

S & F continuous (piano) hinges, mild steel, bright finish or electrogalvanised with width of flap (when open) 30mm complete all as specified and directed

Dismantling floor, hearth, or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed

M&L Glazed ceramic coloured tiles in skirting/dado 300 x 450 x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match required shade over and including 10 mm thick cement plaster in cement mortar 1:4 as in backing coat rough finished surface complete all as specified.

M&L Non-skid cermic coloured tiles 7 to 8 mm thick (square / rectagular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, over screed bed 15 mm thick in cement mortar 1:6 complete all as specified.

M&L vitrified (light shade) coloured tiles 7 to 8 mm thick (square / rectagular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, over screed bed 15 mm thick in cement mortar 1:6 complete all as specified.

M&L vitrified (light shade) coloured tiles 7 to 8 mm thick (square / rectagular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, including 10 mm thick cement plaster in cement mortar 1:4 as in backing coat rough finished surface complete all as specified.

Demolition of stone slab and tiles of any description and thickness in floors, aprons etc laid and pointed in any mortar, complete all as specified.

M&L machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab, size of each slab not be less than 0.28 Sqm, including rubbing and mirror polishing complete over 20mm thick screed bed in cement mortar 1:6, complete all as specified.

M&L Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed in CM 1:4, and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing & complete all as specified & directed.

M&L 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillers, window-cills, cooking platforms over screed bed 20mm thick in cement mortar 1:4 including pointing in white cement (1:2) unsing marble dust with admisture of pigment to match with shade of granite complete all as specified & directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically described (reinforement cut as required to facilitate demolition), complete all as directed by Engineer-in-Charge.

M & L RCC nominal mix 1:2:4, type, B-1 (using 12.5mm graded crushed stone aggregate), as in slab supported on walls, columns in floors, roofs, landings, balconies and in shelves, ducts, manholes cover etc complete all as specified.

M & L TMT bars, 10 mm dia and over cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire(annealed) not less than 0.90mm dia as in stirrups, complete all as specified

M & L form work to sides and soffits of shelves including supports, overhangs etc and similar works rough finished complete all as specified .

S&F Anodized aluminum powder coated sliding cupboard cabinet with shutter vertical member of size 47.62x44.45x3.18 mm and frame size 44.45x44.45x3.18 mm with and including providing and fixing 2 Nos aluminum door handles of 150 mm size to each shutter, tower bolts 200 mm size floor door spring/door closer , 5.5 mm thick tinted glass/bakelite sheet and cylindrical lock including neospreme lining complete all as specified and directed.

Supply and fxing 100 mm dia sand cast pipe, cast iron soil waste and vent pipe ISI marked in any length with or without ears with cement joints fixed to wall, complete all as directed

Supply and fxing 75 mm dia sand cast pipe, cast iron soil waste and vent pipe ISI marked in any length with or without ears with cement joints laid in floors or in trenches, complete all as directed

Supply and fxing cast iron floor trap of 75mm dia of outlet, ISI marked, with grating including jointing to waste pipe with fixed in cement concrete 1:2:4, type B-1 complete all as specified.

Supply and fxing cast iron bends (any radius) diminishing pieces or tapers (larger bore measured), bore of pipe 100mm ISI marked, complete all as specified.

Supply and fxing cast iron bends (any radius) diminishing pieces or tapers (larger bore measured), bore of pipe 75mm ISI marked, complete all as specified.

Supply and fxing 100 mm dia cast iron 'P' or 'S' trap ISI marked complete all as specified.

Supply and fxing cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branchs, ISI marked, bore of pipe 100mm, complete all as specified.

Supply and fxing cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branchs, ISI marked, bore of pipe 75mm, complete all as specified.

S & F grating doom 100mm dia of PTMT (minimum weight 25gms), suitable for floor traps, all as specified and directed.

Supply and fxing PVC valve less symphonic action type flushing cistern 10 ltr capacity , low level white with inlet ball valve float and handle including brackets including 32mm dia PVC flush pipe for low level cistern including all joints , complete all as specified.

Supply and fxing in repairs, Vitreous china squatting pan (Orissa pattern) size 580 x 450 mm, white, with integral foot rests, complete connection to drain (outgoing pipe) and to flushing pipe of 32mm dia and syphonage pipe etc, and complete, all as specified and as directed.

S & F Vitreous china wash down water closet pan (pedestal pattern), white including 10 Litre PVC flushing cistern, saet cover plastic flat bottom and flush pipe with & including fixing nut bolts, connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe etc fixed in repair,complete all as specified

Supply and fixing in repairs, vitreous china white wash hand basin oval shape, counter top of bowl size 430 x 300mm and including waste pipe PVC 32mm dia complete all as specified.

S&F in repairs vitreous china urinals, half stall complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 , securing urinal to plugs with and including 60mm long brass screws, poiting around urinal back in cement, fixing automatic cistern with brackets, flush pipe, grating and union for discharge pipe complete all as specified.

S & F stainless steel sink 1mm thick for kitchen or laboratory wih plugs, washers and wastes including fixing bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mmx420mm bowl size 410mmx330mmx160mm fixed, complete all as specified.

S & F stainless steel sink with drianage board 1mm thick for kitchen or laboratory wih plugs, washers and wastes including fixing bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mmx460mm bowl size 410mmx330mmx160mm fixed, complete all as specified.

Supply and fxing in repair stainless steel plate rack 900 x 600 x 200 mm deep with plate rack, spoon holders , shelves etc , complete all as specified.

Taking up or down steel tubing of 15mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down steel tubing of 20mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store complete all as specified and directed.

M & L cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in stone walls, complete all as specified.

M&L Steel water tubing of 15 mm bore ‘medium grade’ galvanized with all fittings fixed to walls and ceilings or laid in floors, complete all as specified.

M&L Steel water tubing of 20 mm bore ‘medium grade’ galvanized with all fittings fixed to walls and ceilings or laid in floors, complete all as specified.

Supply and fixing in repairs angle valve of cast copper alloy chromium plated (ISI marked), fancy type screwed down high pressure, screwed both ends for iron pipe or for unions 15 mm bore, complete all as specified.

S & F 20 mm Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified.

Supply and fixing in repairs Bib taps 15mm bore of cast copper alloy chromium plated (ISI marked) fancy type, screwed down, high presure, screwed both ends for iron pipe or for brass ferrule, complete all as specified and directed.

Supply and fixing in repair 15mm bore pillar tap cast copper alloy with capstan head, fancy type, chromium plated (ISI marked), screwed down, high pressure, with or without lettered 'Hot or Cold' with long screwed shank and fly nuts screwed for iron pipe complete, all as specified & directed

M&L PVC connection 15mm size with PTMT nuts on both ends of length 450mm , complete all as specified.

S& F brass chromium plated shower rose 75mm size with or without swivel joints, any size, including fixing to steel pipe or union all as specified and directed

Supply and fixing in repairs steel CP soap dish size 160x160x90mm fixed to plugs with chromium plated brass screws complete all as specified

S & F in repairs tubular towel rail 60cm long between flanges , 20mm dia D type Brass Chromium plated incl necessary brackets, fixed with chromium plated screws and wooden/plastic cleats complete all as specified and directed.

Dismantling water tanks and removing from site capacity exceeding 250 ltr and not exceeding 500 ltr complete all as specified and directed.

Dismantling water tanks and removing from site capacity exceeding 500 ltr and not exceeding 1000 ltr complete all as specified and directed.

Supply and fxing rotational moulded polythene water storage tank, white coloured, tripple layer cylindrical vertical with closed top 500 litre capacity hoisted and fixed in position, including inlet and outlet pipe connections, 20mm dia and 15 mm dia GI pipes medium grade respectively, 20mm GI pipe medium grade over flow pipe 15 cm long wash out with plug complete all as specified and directed.

Supply and fxing rotational moulded polythene water storage tank, white coloured, tripple layer cylindrical vertical with closed top 1000 litre capacity hoisted and fixed in position, including inlet and outlet pipe connections, 20mm dia and 15 mm dia GI pipes medium grade respectively, 20mm GI pipe medium grade over flow pipe 15 cm long wash out with plug complete all as specified and directed.

Taking down cement plaster or cement line plaster on stone or brick walls etc including racking out joints, hacking for key scrubbing down with water etc.complete all as specified.

M&L 15mm thick rendering in cement mortar 1:4 on fair faces of brick or stone masonry surfaces & finishing the surface even and smooth without using extra cement, complete all as specified

M & L 10mm thick cement plaster rendering in cement mortar 1:3 in facia or edging of Chajjas, ceiling and roof projection and making the line in true shape & finishing the surface even and smooth without using extra cement, complete all as specified.

M&L rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 on fair faces of brick and making the line in true shape & finishing the surface even and smooth without using extra cement, complete all as specified.

Preparation of new plaster surface of walls including cornices pilaster etc, and applying two coats of oil bound distemper over and including 3mm thick wall care putty, complete as specified and directed.

Preparation of new plastered surfaces of walls and applying two coats exterior emulsion paint over and including 2mm thick wall care putty, all as specified and as directed .

M&L three coats of white wash including preparation of newly plastered surfaces of ceiling complete all as specified.

Preparation of old treated surfaces of walls by removal of existing treatment and applying two coats exterior emulsion paint over and including 2mm thick wall care putty, all as specified and as directed .

Complete removal of existing treatment of walls including cornices pilaster etc, and applying two coats of oil bound distemper over and including 2mm thick wall care putty, complete as specified and directed.

Supply and fxing in repair curtain rod 25 mm dia pre painted synthetic enamel paint of wooden finish , fixed with screws complete all as specified.

Supply and fxing in repair wooden (turned, weathered & mitred) brackets of Ist class hard wood pre polished with french polish and touch wood with cut hole suitable for 25 mm dia rod fixed with screws and gutties in wall, complete all as specified and directed.

Supply and fxing in repair wooden (turned, weathered & mitred) end caps with ornament and fixed to curtain rod with screw of design/shape complete all as specified and directed.

PCC 1:2:4, type B-1 (using 20mm graded crushed stone aggregate), roof kerb or mud stops,rounded or chamfered angles and edges, complete all as specified and directed.

M & L cleaning of existing roof treatment of any descrition completely and washing, rubbing with water and providing 20mm thick in cement mortar (1:4) on flat roof surfaces finished fair and even without using extra cement, to receive water proofing treatment complete all as specified. (The rate includes for filling cracks in existing roof with cement putty using suitable bonding agent (shalcrate 42) before laying cement plaster) and providing and laying of water proofing treatment of roof APP (Atactic Polyproplyllen) modified prefabricated five layer 3mm thick water proofing membrane, super thermply non woven polyester mat reinforcement of 160 gsm, weight of membrane @ 3.6 Kg/Sqm over a solvent based bitumen primer @ 0.3 Ltr Sqm by the same manufacturer conforming to IS:3384-1986 , The membrane shall be laid using bitmun torch.The end lap should be 100 mm and the side lap must be minimum 75 mm the membrane shall be first laid up to the parapet wall junction and then shall be overlapped with another membrane (flashing) with an overlap covering up to a distance of 300mm. In case parapet height is less than/ up to 500 mm, membrane shall be terminated at the top of parapet.All rain water pipe opening shall be suitably sealed with the APP membrane all as specified and directed.

Supply only Liquid water proofing admixture of approved brand complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description complete all as specified and directed.

M & L steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 including one shop coat of Zinc chromate primer paint including preparation of surface,complete all as specified.

Dismantling asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified.

M & L pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified.

M & L pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/ slabs/ blankets, any thickness, including cover fillets, complete all as specified.

S & F 6mm thick AC 'E' classic board (ISI marked) of size 600x600mm as used in false ceiling fixed as per manufacturer instruction, complete all as specified and directed

S&F 605x605mm anodised aluminium snap grid frame work including anchoring with MS wire not less than 4mm dia . The snap grid shall consist of aluminium anodised main/cross Tee of size 36.5x25x1.4mm weighting 0.24 kg per RM and 23.5x26.4x1.4 mm wheighting 0.191 KG per RM respectively. The size of aluminium angles 40x25x2mm wheighing 0.36 Kg per RM complete all as specified and directed

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically described complete all as directed by Engineer-in-Charge.

M & L Plain Cement Concrete 1:2:4, type B-1 (using 20mm crushed stone aggregate), 75mm thick as in path, flooring etc laid in alternate bays finishing even and fair complete all as specified.

M & L vibro compressed chemical coated chequered cement concrete tiles 300x300x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and no pigment including 20mm thick in cement moratr 1:6 complete all as specified and directed.

Demolition of stone slab, paver block and tiles of any description and thickness in floors, aprons etc laid and pointed in any mortar, complete all as specified.

M & L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed

M & L vibro compressed precast concrete interlocking paver block shape and size as approved by GE confirming to IS 15658-2006 of 60mm thickness, M-35 Grade with grey cement and no pigment complete all as specified and directed

Notes : The Schedule of Credit amount shall be deducted from the total of this schedule(BoQ) to arrive at Contract Sum.

jagdambe traders

VIKRAM SINGH MANHAS

Amarjit Brothers

M/S Ajay Kumar Mahajan