Renovation Of Officers Hostel at Dr YSP University of Horticulture and Forestry NauniSolan

Amount

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto all leads and lifts as directed by Engineer-in- Charge. a). All kinds of soil

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering work up to plinth level with 1:5:10 (one cement : five sand : ten graded stone aggregate 40 mm (forty milimetre) nominal size etc. complete in all respect as per satisfaction of Engineer-in-charge.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to all floor level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (one cement : one & half coarse sand : three graded stone aggregate 20 mm(twenty milimetre) nominal size) etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Centering and shuttering including strutting, propping etc. and removal of form for etc. complete in all respect as per satisfaction of Engineer-in-charge.

a). Suspended floors, roofs, landings, balconies, shelves and access platform.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level etc. complete in all respect as per satisfaction of Engineer-in-Charge. a) Thermo-Mechanically Treated bars of grade Fe-500D or more.

Smooth finishing of the exposed surface of R.C.C. Work with 6 mm thick cement mortar 1:3 (one Cement: three sand) complete in all respect as per satisfaction of Engineer-in-Charge..

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to all floor level with Cement mortar 1:4 (one cement : four sand) etc. complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing plywood 4 mm thick, one side decorative veneer conforming to IS: 1328 (type-1), for plain lining / cladding with necessary screws, including priming coat on unexposed surface with Decorative veneer facings of approved manufacture etc. complete in all respect as per satisfaction of Engineer-in –charge.

Providing Sal wood work in frames of false ceiling, partitions etc. sawn and fixed in position with necessary stainless steel screws etc. complete in all respect as per satisfaction of Engineer-in –charge. .

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws with 35 mm thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size etc. complete in all respect as per satisfaction of Engineer-in-charge. a) Kiln seasoned and chemically treated hollock wood.

Providing and fixing 2nd class teak wood 40mm into 12 mm wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters etc. complete in all respect as per satisfaction of Engineer-in-Charge.

a). 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

b). 25 mm thick( for cup board) including ISI marked nickel plated bright finished MS piano hinges with necessary screws.

Providing and fixing ISI marked oxidized/ /Cromium plated M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge

a). 200x10 mm( Two hundred into ten milimetre)

b). 150x10 mm( One hundred fifty into ten milimetre)

Providing and fixing ISI marked oxidized/ chromium plated M.S. handles conforming to IS:4992 with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge

a). 125mm (one hundred twenty five milimetre)

Providing and fixing ISI marked oxidized/ chromium plated M.S. single acting spring hinges with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge.a)150 mm ( one hundred fifty milimetre)

Providing and fixing 50mm bright finished brass cup board or wardrobe knob of approved quality with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge

Providing and fixing 50mm special quality bright finished brass cup board or wardrobe locks with four levers of approved quality including necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge .

Providing and fixing 18 mm thick Pre-laminated medium density fibre board IS: 14587:1998 marked, with one side decorative lamination other side balancing lamination Grade-I(exterior grade) in shelves with screws and fittings wherever required,edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand etc. complete in all respect as per satisfaction of Engineer-in-Charge (Actiontesa/ Green/ Century plymake) (fittings to be paid separately).

Steel work in tubular( Square, rectangular and round hollow tubes etc.) riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer etc. complete in all respect as per satisfaction of Engineer-in-Charge

40 mm (forty milimetre) thick Cement concrete flooring 1:2:4 (one cement : two coarse sand : four graded stone aggregate 20mm (twenty milimetre)nominal size finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete in all respect as per satisfaction of Engineer-in-Charge

Chequerred precast cement concrete tiles 22 mm thick (NTC make) in footpath & courtyard, jointed with neat cement slurry mixed with dark pigment shade to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm using ordinary cement thick bed of cement mortar 1:4 (1 cement: 4 coarse sand) required etc. complete in all respect as per direction of Engineer-in-Charge a). Dark shade pigment using ordinary cement

Providing and laying rectified Glazed Ceramic floor tiles (Kazaria / Oreint bell / Nitco/ Somany make) of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (one Cement : four sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc complete in all respect as per satisfaction of Engineer-in-Charge.

Grouting the joints of size 1000 into 1000mm flooring tiles/ chips having joints of 3 mm width in different size of tiles/ Kota stone, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing etc. complete as per the satisfaction of Engineer-in-charge

Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified etc complete in all respect as per satisfaction of Engineer-in-Charge.

a). 2 mm thick corrugated (2.5" or 4.2" or 6") or step-down (2" or 3" or 6" ) as specified

15 mm (fifteen milimetre thick) cement plaster on rough side of single or half brick wall of mix with cement mortar 1:6 (one cement: six sand) complete in all respect as per satisfaction of Engineer-in-Charge.

Applying priming coat with ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) complete etc. in all respect as per satisfaction of Engineer-in-Charge.

Painting with oil type wood preservative of approved brand and manufacture work etc. complete in all respect as per satisfaction of Engineer-in-Charge. a) New work (two or more coats)

Painting with synthetic enamel paint on steel and wood of approved brand and manufacture to give an even shade as required complete in all respect as per satisfaction of Engineer-in-Charge a) Two or more coats on new work.

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade etc. all complete as specified and as directed by the Engineer-in-Charge a)Two or more coats on new work

French spirit polishing two or more coats on New works including a coat of wood filler as required etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade etc. in all respect as per satisfaction of Engineer-in-Charge a) One or more coats on old work

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade etc. in all respect as per satisfaction of Engineer-in-Charge a) One or more coats on old work

Finishing walls with Acrylic Smooth exterior paint of Required shade etc. in all respect as per satisfaction of Engineer-in-Charge. a). Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface .

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in- Charge a).With cement mortar 1:4 (one cement : four sand)

Renewing glass panes and refixing existing wooden fillets etc. in all respect as per satisfaction of Engineer-in-Charge a).Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm)

Racking out joints in glass strips, lime or cement mortar and preparing the surface for re pointing or re-plastering, including disposal of rubbish to the dumping ground etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Demolishing R.C.C. work manually/by mechanical means including stacking of steel bars and disposal of unserviceable material within all leads, lifts and carriage of material as per direction of Engineer-in-Charge

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within all leads etc. all complete as specified and as directed by the Engineer-in-Charge a). For thickness of tiles 10mm to 25mm

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required complete in all respect as per satisfaction of Engineer-in-Charge (Cera/ Hindware make). a) W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing rectangular shape 1500x450 mm mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing etc. all complete as specified and as directed by the Engineer-in-Charge.

Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer-in-Charge.

Providing and fixing 6mm thick water proof commercial ply of standard quality ISI marked and approved shade & colour in wall lining & ceiling with butt jointing and nails complete in all respect as per satisfaction of Engineer-in-charge. (Frame work and cover fillets to be paid for separately

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete in all respect as per satisfaction of Engineer-in-charge (Filolex / Kisan / D-Plast make) . a) 110mmx75mm

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast/ Prayag make).

a). 75mm (Seventy five millimetre) dia dia

b). 110mm (One hundred ten millimetre) dia

Providing and fixing PVC plain bend ISI marked complete including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast/Prayag make)

a). 75mm (Seventy five millimetre) dia dia

b). 110mm (One hundred ten millimetre) dia

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast/ Prayag make).

a). 75mm (Seventy five millimetre) dia dia

b). 110mm (One hundred ten millimetre) dia

PREM KRISHAN (BID ID -470034)

Pawan Kumar (BID ID -470024)