ADDN / ALTN TO BLDG NO. P-53 UNDER GE (NORTH) UDHAMPUR

Amount

Demolition of brick work or stone boulder masonry, built in cement mortar including all quoins, arches, pillars etc., complete all as specified and directed.

M&L for brick work with using sub class 'B' bricks, old size, straight or curved on plan exc 6 mtr mean radius, built in CM 1.6, complete all as specified and directed.

All as per serial item No. 2.00 here-in-above but except bricks.

Taking down cement plaster on brick walls, stone masonry/ walls, concrete surfaces etc. including raking out joints, hacking for key, scrubbing down with water etc., complete all as specified and directed.

M&L for 10mm thick rendering in CM 1:3 as on ceiling, finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:4 with using water proofing compound as on fair faces of brick work, concrete surfaces, chajjas, roof projection, facia etc, complete all as specified and directed. Notes :- (a) WPC shall be measured and paid separately under respective item of this BOQ. (b) The shall be carried out in double storey buildings. (c) Rates for necessary scaffolding shall be deemed to include in the quoted rates.

M&L for 15mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:6, finished the surface even and smooth without using extra cement, complete all as specified and directed.

Supply only liquid water proofing compound, complete all as specified and directed.

M&L for preparation of new surfaces of walls and applying two coats of oil emulsion distemper over and including a coat of primer and including 1-2mm thick wall care white putty, complete all as specified and directed.

M&L for complete removal of existing treatment and preparation of old surfaces of walls and applying two coats of oil emulsion distemper over a coat of primer and including 1-2mm wall care white putty, complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 Sqm over and including priming coat of exterior primer applied @ 0.9 litre/10 Sqm over surfaces all as specified and directed.

M&L for preparation of old plastered surfaces of walls with complete remoal of existing treatment and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 Sqm over and including priming coat of exterior primer applied @ 0.9 litre/10 Sqm over surfaces all as specified and directed.

M&L for preparation of old surfaces of ceiling and applying two coats of oil bound distemper over and including a coat of chalk whiting primer, complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings, not exc 15cm thickness (below or above ground level), complete all as specified and directed.

Dismantling floor, hearth or wall tiles including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

M&L for 8-10mm thick vitrified ceramic tiles of any colour (square or rectangular), light shade, polished, area of each tile not exc 0.36 Sqm, laid in floors over and including 15mm thick screed bed or bedding layer in CM 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, complete all as specified and directed.

M&L for 8-10mm thick vitrified ceramic tiles of any colour (square or rectangular), light shade, polished, area of each tile not exc 0.36 Sqm, fixed in skirting/ dados or verticle surface over and including 10mm thick screed bed or bedding layer in CM 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, complete all as specified and directed.

M&L for 7-8mm thick non skid coloured ceramic tiles, area of each tile exc. 0.11 Sqm but not exc 0.18 Sqm, laid in floor, laid/ fixed over and including 15mm thick screed bed or bedding layer in CM 1:6, set and jointed with neat cement slurry and pointed in white or coloured cement to match the shade of tiles, complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 300x250x7mm or 450x350x7mm thick as on verticle surfaces, fixed on wall, skirtings or verticle surfaces over and including 10mm thick plaster/ backing coat in CM 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, complete all as specified and directed.

M&L for 25mm thick plain cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates) as in leveling course, sub base etc, finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for 75mm thick plain cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregates) as in path or sub base, complete all as specified and directed.

M&L for 18-20mm thick machine cut kota stone slab, as in floos, laid over and including 20mm thick screed bed or bedding layer in CM 1:3, jointed and pointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing, complete all as specified and directed.

M&L for 18-20mm thick machine cut kota stone slab, as in skirtings, dados, pillars or verticle surfaces, fixed over and including 10mm thick plaster in CM 1:3, jointed and pointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing, complete all as specified and directed.

M&L for hardcore of broken stone or boulders of gauge not exc 63mm, deposited, spread and leveled in layers not exc. 15cm thick, watered and well rammed to a true surface, complete all as specified and directed.

Demolition of RCC shelves, slabs, chajjas and similar work, not otherwise specifically provided for, complete all as specified and directed.

M&L for reinforced cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregates) as in slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed.

M&L for reinforced cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregates) as in beams, cantilevers, bressumers, lintels over 1.5 m in span,complete all as specified and directed.

Use and waste of form work for slabs, beams, landing and shelves etc. complete all as specified and directed.

M&L for precast cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregates) as in landing cover slab, manhole cover, chajja shelves etc, set in cement mortar 1:6, complete all as specified and directed.

M&L for TMT mild steel bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

M&L for TMT Mild steel bars 6-8mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends or as in stirrups and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

M&L for granite (of any type work) 20 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar 1:4 including pointing in white cement 1:2 and rounding of edges over and including 15 mm thick screed bed in cement mortar 1:4, complete all as specified and directed.

Taking down shutter of any description, area exc 1.0 Sqm but not exceeding 2.0 Sqm each, complete all as specified and directed.

Taking down shutter of any description, area exc 1.5 Sqm but not exceeding 4.0 Sqm each, complete all as specified and directed.

Taking down shutter of any description, area not exc 1.5 Sqm each, complete all as specified and directed.

S&F powder coated (minimum thickness of powder coating 50 micron) aluminium frame for door, windows, ventilators & partition with one or more rebates including joining cleats for fixing etc, complete all as specified and directed.

S&F powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows (sliding type), ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows (sliding type) & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge

S&F 5.5mm thick sheet glass, ordinary quality, glazing & fixed with aluminium and rubber beading in square not exc 0.50 Sqm in each pane, sheet glass is ground or obscured or frosted on one side, complete all as specified and directed.

S&F 5.5mm thick sheet glass, ordinary quality, glazing & fixed with aluminium and rubber beading in square exceeding 0.50 Sqm in each pane, sheet glass is ground or obscured or frosted on one side, complete all as specified and directed.

M&L for anodised aluminium grill (anodised transparent or dyed to required shade according to IS:1868 with minimum anodic coating of grade AC15) of approved design/ pattern with approved standard section and fixed to the existing window frame with CP brass/ stainless steel screws @ 200mm c/c including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, complete all as per site requirement and directed by Engineer-in-Charge.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and as directed.

S&F 75mm size brass mortice lock vertical type, vertical type, 4 levers, complete all as specified and directed.

S&F door closer hydraulically regulated, aluminium (extruded section body) designation No 3 universal type, suitable for door shutters of 800 to 1000 mm width and of weighht between 36 to 60 KG, complete all as specified and as directed.

Supply only, plain ACP board 5 mm thick, fixed in aluminium joinery including cutting, packing finishing complete all as specified and as directed.

S&F solid PVC door frame of size 50x47mm, made out of 5mm thick single side prelam heat moulded extruded PVC profile & edges will be painted to match with prelam sheet reinforced with M.S Square tube, suppling & fixing in opening as per specification & drawing.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded extruded PVC profile channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour heat moulded extruded PVC profile for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; both side Prelam PVC sheet , Stile & rails feathered at edges MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with solvent cement complete all as specified and directed.

S&F 100mm size cadmium plated stainless steel butt hinges and fixed with stainless steel screws, complete all as specified and directed.

S&F 200mm long,stainless steel, barrel tower bolts of extruded section complete all as specified and directed.

S&F 150mm stainless steel handles fabricated type anodised complete all as specified and as directed.

S&F stainless steel sliding door bolt, plate type, 300mm long, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts & nuts, 4 on bolt plate and 2 on staple plate and fixed complete all as specified and as directed.

S&F pressed steel frames size 105 x 60mm for doors with one or more rebates including necessary fixing lugs hinges, lock strike plates etc. with and including filling of PCC 1:3:6 type C1 (20mm graded stone aggregates) complete all as specified and directed.

S&F flush shutters 30mm thick, soild core construction, with block board core and plywood face panels commercial type on both sides.

M&L butt hinges, medium weight 100 mm size cold roled mild steel (including welding to steel chowkhats) complete all as specified and directed.

S&F floor door stopper of stainless steel body and tongue, with hard drawn steel spring, fixed in floor, overall length double legged of cover plate 140mm complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint over a coat of pink primer to new wooden surfaces including preparation, exc 10 cm width or girth, complete all as specified.

Forming jambs etc to openings in cement mortar 1:6, including cutting, toothing and properly bonding into old work also facing, jointing and pointingto match existing work complete.

M&L for repairing the edges of the chajja/roof projections in cement mortar 1:3 finished fair and even and applying two coats of cement base paint including removing the loose concrete/plastering complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

M&L for mild steel work as in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and as directed.

M&L for rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins FE 410-W (Gde-E-250) Quality -A where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, complete all as specified and as directed.

M&L applying two coats of synthetic enamel paint over a coat of red oxide or zinc chrome primer including preparation of new steel or iron surfaces exc 10 cm width or girth, complete all as specified and as directed.

Taking up or down steel tubing and connections including cleaning for refixing with all fittings for 15 mm bore GI tubing complete all as specified and as directed.

Taking up or down steel tubing and connections including cleaning for refixing with all fittings for 20 mm bore GI tubing complete all as specified and as directed.

M&L for cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves lintels etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good cutting not exc 10cm girth complete all as specified and as directed.

S&F medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 15 mm bore GI tubing complete all as specified and as directed.

S&F medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 20 mm bore GI tubing complete all as specified and as directed.

S&F in replacement 10 Ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets including flush down pipe complete all as specified and as directed.

S&F PVC connection 15mm size with PTMT nuts, of 450 mm length complete all as specified and as directed.

Dismantling water tank of exc 500 ltr and not exc 1000 ltr Capacity complete all as specified and as directed.

S&F rotational moulded polyethylene 1000 Ltrs Capacity water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position in SSR Part-I including ball brass valve, with polythelene float three layer external white with thread type cover and fly nut complete screwed down for iron pipe of 20 mm dia complete all as specified and as directed.

Cleaning & removing all scale & dirt etc from tanks & from mouths of circulating pipes etc of capacity exc 250 litres & not exc 500 litres with gunny bags, sand cleaning with fresh water and bleaching powder complete all as specified and as directed.

S&F in replacement ball valves 20mm dia high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for ironpipe and fixed. (Minimum weight 15mm-142 gms/ 20mm-210 gms/25mm-455gms/ 40mm- 690 gms) complete all as specified and as directed.

S&F in replacement 550x400mm Wash basin, vitreous China (Flat back any size ) including fir and pinning in ends of brackets exclusive of waste pipe but including bracket Each complete all as specified and as directed.

S&F vitreous china, coloured, counter top wash hand basin, oval type size 550mm including cutting fo and pinning in, including waste pipe complete all as specified and as directed.

S&F CP brass WHB mixers for hot and cold water mixing of 15mm dia screwed down for iron pipe complete all as specified and directed.

S&F Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and as directed.

S&F CP shower rose 15mm dia complete all as specified and directed.

S&F in replacement vitreous china water closet padestal pattern S/P trap pattern(white) excluding fixing bolts, flushing cistern and flush pipe complete all as specified and directed.

S&F in replacement Vitreous China urinals, half stall urinal type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe with grating and union for discharge pipe including of supply pipe to flushing cistern, trap and waste pipe complete all as specified and directed.

S&F health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipewith 1.25 meter long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F pillar taps 15mm bore fancy type cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or without lettered hot or cold with long screwed shanks and fly nuts, screwed to iron pipe & fixed complete all as specified and as directed.

S&F in replacement CP concealed stop cock fancy type 15mm dia complete all as specified and directed.

S&F in replacement fancy type chromium plated long body bib tap, cast copper alloy, with round headed knob , screwed down, screwed for iron pipe or for brass ferrule of 15mm bore, complete all as specified and as directed.

S&F fancy type chromium plated short body bib tap, cast copper alloy, with round headed knob , screwed down, screwed for iron pipe or for brass ferrule of 15mm bore, fixed in repairs.

S&F grating doom 125mm dia with waste hole of PTMT. (minium weight 40 Gms) complete all as specified and as directed.

S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

S&F soap dish mild steel chromium plated, complete all as specified and as directed.

S&F Corner glass shelf with chromium plated guard rails complete all as specified and directed.

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed.

S&F Tubular towel rail, 20mm dia chromium plated, D type, 60cm long between flanges complete all as specified and as directed.

S&F 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed on walls complete all as specified and as directed.

S&F in repair 110mm PVC(SWR) bends any radius with acess door complete all as specified and as directed.

S&F in repair 100mm dia centrifugally Cast iron spun fioor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and as directed.

Excavation over areas, n exc 1.5m deep and getting out in soft/loose soil complete all as specified and as directed.

Excavating in trenches, n exc 1.50m wide and n exc 1.5m in depth, for foundation etc or for shafts, wells, cesspits, manholes, pier holes, etc n exc 10 Sqm on plan and n exc 1.5m in depth and getting out in soft/loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm complete all as specified and as directed.

S&F salt glazed stoneware drain pipes 150mm laid in trenches and jointed complete all as specified and as directed.

S&F cutting into existing manholes 150mm for connecting new drains, making good to pipe and rendering, cutting out eixting benching for and forming branch channel (1/2 round or 3/4 section) in cment concrete 1:2:4 type B-I smooth finished, and reforming benching as required complete all as specified and as directed.

M&L concrete bed to drain pipes 150mm bore including packing under, and haunching against the sides of pipes after they are laid and tested , in cement concrete 1:4:8 type D-2 complete all as specified and as directed.

M&L for cement concrete type C-1, 1:3:6 (using 20mm graded stone aggregate) as in surface channels and drains, complete all as specified and as directed.

Providing precast cement concrete 1:2:4 type B-1 (using 20mm graded stone agg) as in manhole covers set in cement mortar 1:6 all as specified and directed including necessary formwork and moulds complete all as specified and as directed.

Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and as directed.

Removing excavated material (soil) n.exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and as directed.

M&L for PCC 1:5:10 type E-2 using 40mm graded crushed stone aggregate as in foundation filling and mass concrete complete all as specified and directed..

Providing cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60cm height, copings, kneelers, apex stone, bed plates and the like uncluding weathering slighly rounded or chamfered angles and throating, all as specified and directed.

M&L for stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangements, complete all as specified and as directed.

Complete removal of existing roof treatment of any thickness including tiles, any type from RCC roof by stripping out old tar felt over roofs, parapets, chimney stacks etc laid horizontally or vertically including taking out layer of cement plaster and PCC of any thickness over RCC roof surface complete by scrapping/scrubbing/brooming etc and cleaning the surface all as specified and directed and removing debris from the site.

M&L for rendering 15mm thick in CM 1:4 on concrete surfaces and finish the surfaces and finish the surface even and smooth without using extra cment mixing with water proofing compound @ 2% of cement concrete all as specified and directed. Note : WPC shall be measured and paid seperately.

Providing water proofing treatment over RCC roof incl projections as follows:- (a) Apply a coat of bituminous primer confirming to IS-3384 @ 0.3 Ltr/Sqm on the prepared surface of plaster. (b) Apply a coat of hot blown VG 20 paving graded bitumen (60-80 penetration) confirming to IS-702 @ 1.2 Kg/Sqm of plastered surface. (c) Provide polymeric water proofing membrane ISI marked laid with overlaps, bonded with hot blown bitumen, and laid by torch application, end overlaps shall not be less than 150mm and side lap 75mm. Polymeric wate proofing membrane should be five layered with centre core as 90 micron high molecular high density polythylene film, min weight 3 kg per sqm. The water proofing membrane of one of the following firms shall be used :- (i) Hyper Plus standard - manufactured by M/S IWL India (ii) Multi Plus manufactured by M/S STP Texas Ltd (iii) Bengal Acquaflux - Bengal Bitumen (iv) Superior Poly Plus 310 by STP Ltd.

S&F Cement concrete tiles 20cm x 20cm x 20mm thick of grey cement with not pigment laying over and including10mm thick cement mortar 1:3 ,machine pressed; set jointed and pointed in neat cement slurry in floors, and cut and polished over 25mm thick PCC 1:2:4 type B-1 using 20mm graded aggregate complete all as specified and directed..

M&L for 18/19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work for kitchen cabinets including partitions ( any number) including dismantling complete all as specified and directed.

S&F brass drawer handles, projection drop (50mm to 65mm) on screwed plate complete all as specified and directed..

S&F parliament hinges, mild steel cold rolled 75mm wide complete all as specified and directed.

S&F 25mm dia harrison rails / curtain rods, mild steel, chromium plated with and including all necessary fittings such as brackets, stops rollers, knobs etc. as required, complete all as specified and directed.

Providing and fixing 4mm thick designer cement fibre ceiling board in ceiling fixed with screws as per manufactures instructions (Make : Everest or euivalent) laid on hot dipped galvanized iron imposed grid with 24mm wide T-section exposed flanges which shall be under coated white. The frame shall comprise of main runner made from 0.33mmm thick galvanized steel sheet & size of 24 x 32x 300mm and spaced at 12mm centres securely fixed to the structural soffits by approved hangers at 1200mm maximum centres. hangers of GI wire 4mm dia to be fixed by the approved rowl plug, level adjusters and screws etc. The last hanger at the end of each main runner shall not be greater than 450mm from adjacent wall flush fitting of 1200mm long cross tee with (double stitching) to be inter locked between main runners at 600mm centre to from 1200 x 600mm modules cross tee longer than 600mm modules to be formed by fitting 600mm long cross tee, tee perimeter wll angle shall be of 0.45mm thick galvanized steel of size 19 x 19mm and 300 mm long of white colour all as per instruction complete all as specified & directed.

S&F in replacement stop valve, cast copper alloy, with round headed knob, screwed down both ends for high pressure, as per ISI suitable for 20mm dia iron pipe all as directed.

S&F in replacement CP brass Angle cock 15mm dia complete all as specified and directed.

S&F brass CP peg set of five hooks each fixed with screws complete all as specified and directed.

S&F plate rack of size 75x90x30 cm made out off 1.00 mm thick stainless steel complete all as specified and as directed.

S&F in replacement vitreous china water closet (squatt pan) orrisa pattern 580x440 mm size pan white with front or back inlet with integral 'foot rests including provn of lime concrete bedding including connections to 'flushing cistern/pipe complete all as specified and directed including 100mm CI spun 'P' trap in one piece 60cm long complete all as specified and as directed.

M&L for 75mm thick PCC 1:3:6 type C-2 as in plinth protection with 6 x 10mm groove in every 3m and filled with bitumen mastic filling, finished even and fair complete all as specified and as directed.

Demolition of cement concrete in any description complete all as specified and directed.

M&L Extra for forming fair finished drain or channel not exc. 30 cm inner girth in cement concrete using extra cement.

S&F Continuous (Piano) hinges, mild steel, bright finished or electro galvanized, width of flaps (When open) 30mm, complete all as specified and as directed.

S&F 150mm stainless steel hasp and staples safety type, including bolt to hinges plate and fixed with screwed

S&F figured glass, pin headed type 4mm thick and glazing with oil putty with glazing pin in squares n.exc. 0.5 sqm each pane complete all as specified

S&F sheet glass ordinary quality 4mm thick and glazing with oil putty with glazing pin in squares n.exc. 0.5 sqm each pane complete all as specified

Taking down AC/Salt glazed ware pipes and fittings upto 110mm complete all as specified

S&F 100mm dia centrifugally cast iron pipe in any length with or with ears, with cement joints laid in trenches or in floors complete all as specified.

All as per serial item No. 132.00 here-in-above but fixed to walls, complete all as specified and directed.

S&F 75mm dia centrifugally cast iron pipe in any length with or with ears, with cement joints laid in floors complete all as specified.

All as per serial item No. 134.00 here-in-above but fixed to walls, complete all as specified and directed.

S&F in replacement centrifugally cast iron bends any radius for 100 mm dia with duck's foot or heel rest complete all as specified and directed.

S&F in replacement centrifugally cast iron bends any radius for 75 mm dia with duck's foot or heel rest complete all as specified and directed.

S&F in replacement centrifugally cast iron bend (any radius) of 75mm bore with oval access door complete all as specified and directed.

S&F in replacement centrifugally cast iron bend (any radius) of 100mm bore with oval access door complete all as specified and directed.

S&F in replacement 75mm dia cast iron cowls complete all as specified and directed.

Taking down carefully alu/copper point wiring light, fan socket, or power complete with (fittings Per poin such as old rusted steel conduit switches ceiling rose pendants, regulators, socket etc to be measured separately) removing material to store for disposal by Sch of credit and making good to disturbed surfaces of walls floors etc and all as specified.

Dismantling and taking down fluorescent tube light single/double of any wattage or size fittings for repair or replacement of burnt/worn out accessories or carrying to MES store for reuse or taking in schedule of credit.

Taking down unserviceable/serviciable MCB DB's/AC's box including MCCB/MCBs takeing in schedule of credit of any size/rating complete all as specified and directed by Engr-in-charge.

M&L for Point wiring using approved color coading as per IS code (Red, Black and Green for single phase circuit) with multi stranded copper condutor 1.5 Sqmm nominal cross section area, single core, PVC insulated and unsheathed FRLS cable 1100V grade, in and including medium grade, PVC concealed conduit ISI marked of dia not less than 25 mm and conduilt accessories concealed in wall/roof/floor etc with terminated to new pressed flush metal box and readily available cover with outer plates and inner plates etc, suitable for mounting modular type switches, sockets, fan regulators etc PVC insulated PVC insulated multistranded copper condutor 1.5 sqmm nominal cross section area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for the followings :-

All as per serial item No. 144.00 here-in-above but One light Point controlled by one, one way switch.

All as per serial item No. 144.00 here-in-above but One ceiling fan controlled by one way switch

All as per serial item No. 144.00 but for One exhaust fan controlled by one way switch.

All as per serial item No. 144.00 but for One wall fan controlled by one way switch.

All as per serial item No. 144.00 here-in-above but for One bell point controlled by one way switch.

All as per serial item No. 144.00 here-in-above but 3 Pin 5 Amp modular Socket on the same board, complete Per po all as specified.

All as per serial item No. 144.00 here-in-above but 3 Pin 5 Amp modular Socket on independent board, complete all as specified and directed.

All as per serial item No. 144.00 here-in-above but M & L for point wiring with two runs of FRLS PVC insulated unsheathed, 1100 V grade cable multi stranded copper conductor of size 2.5 sqmm drawn through in and including PVC conduit size of not less than 25mm concecled in wall / surface including sutiable new annealed sunken boxes, modular frame and cover plate for foing of modular switch, socket and regulator along with earth wire of PVC insulated, unseathed, 1100 V grade cable multi stranded copper conductor of size 2.5 sqmm and for one 5 pin modular socket outlet two in one 16/6 amps on an indeendent board including colour coding of cable shall be Phase- Red, Neutral- Black and Earth- Green and making good, disturb surface as it is complete all as specified and directed.

All as per serial item No. 144.00 here-in-above but for Gyser point wiring with 4 Sqmm multi stranded copper conductor on indepenedent board including colour coding of cables and earth wire connected to common earth/earth dolly complete as specified and directed.

S&F single pole and neutral enclosure with a two pin and earth plug and socket complete With one single pole MCB of 16 to 32 Amps 240 volt capacity complete all as directed .

S&F modular switch single pole one way 6 amps 240 volts with polycarbonate body complete all as specified and directed

S&F modular socket 6 amps 5 pin flush type, 240 volts, with polycarbonate body complete all as specified and directed..

S&F modular socket out let, 5 pin 6 Amps and 15 amps multi purpose 2 in 1 flush type, 230 volts with polycarbonate body complete all as specified and directed.

S&F modular switch single pole one way 16 amps 240 volts with polycarbonate body complete all as specified and directed.

S&F modular electronic fan regulator, step type, two module 120 watt 230 volt and making all necessary connections complete all as specified and directed.

S&F ceiling rose, 3 phase, PVC/polycarbonate, surface type, 65mm x 50mm, insulated body, three terminal complete all as specified and as directed by Engr-in-Charge.

S&F modular bell push type 6 Amp 1 module, complete all as specified and directed.

S&F call bell Ding dong type, complete all as specified and directed.

S&F in replacement of LED Light fitting 20 watt High-quality materials and design. Extruded aluminium housing enhances safety with High quality PC Diffusers Reliable and robust housing structure, maximize the endurance over the life time slim Integrated design, easy to install Efficacy: 110 Im/W and also available in warm white and natural white complete making all connection using 1.5 sqmm copper conductor multistranded PVC insulated twin core flexible cable from ceiling complete ali as per directed.

S&F in replacement of LED Light fitting 10 watt Trimline Neu is a robust and high performance batten. This LED luminaire comprises of extruded channel in thermally conductive material. High translucent serrated milky white diffuseris used to get glare free and smooth light distribution. Efficacy: 110 lm/W Also available in warm white and natural white complete making all connection using 1.5 sqmm.copper conductor multistranded PVC insulated 2 core flexible cable from ceiling rose to fitting complete all as specified and as directed.

S&F in replacement of LED Decorative wall light, gold finish fixture with white glass diffuser suitable for 9 W LED filament lamp E27 base including of 1 No of 9 W LED Lampcomplete with internally prewired and connecting up with twin core flexible copper conductor cable of suitable size complete all as specified and as directed.

Taking down ceiling fan /exhaust fan complete including overhauling, cleaning with soft solution and painting of the same with white enameled paint as existing, or rehanging ceiling fan exhaust fan and connecting up including provision of three core copper conductor cable 1.5 sqmm nominal cross sectional area and length not less than 0.5 mtr from ceiling rose to fan complete all as specified and directed.

S&F in replacement of exhaust fan 300 mm sweep, made of sturdy engineering plastic including louvers shutter, voltage 230 V, 50 Hz RPM 1200 copper winding complete all as specified and as directed.

S&F in replacement of exhaust fan, steel body AC single Phase 230V of size 450 mm sweep with, blades, and frame and louvers voltage 230V, 50 Hz, RPM 1200, Copper winding complete all as specified and as directed.

Supply and fixing in replacement of ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE Five star rated with bushless direct current motor (BLDC) complete all as specified and as directed.

S&F in replacement of wall mounting fan complete with blades, and accessories, 230 V, 400 mm sweep complete all as specified and as directed.

S&F in replacement of 35 Watt LED security light fitting with best in class design & Robust heat sink along with class leading IP, IK & Surge protections for long lasting performance, and with 0.6 mtr long 20/25 mm (as per manufacturer standard) dia GI Pipe in 45 degree bend shape and necessary clamping devices required at site complete all as specified and directed.

M&L for sub main wiring with copper conductor cable 4 runs of multistaranded 16 Sqmm FRLS PVC ISI marked with all insulated unsheathed in and including PVC concealed conduit 25mm dia medium grade fittings including cutting chasing and 1X16 Sqmm copper conductor cable FRLS PVC insulated unsheathed multithreaded using as continues earth wire connected to common earth and earth duly including taking down complete all as specified and as directed.

M&L for sub main wiring with copper conductor cable 4 runs of multi stranded 6 Sqmm FRLS PVC ISI marked with all insulated unsheathed in and including PVC concealed conduit 25mm dia medium grade fittings including cutting chasing and 1X6 Sqmm copper conductor cable FRLS PVC insulated unsheathed multithreaded using as continues earth wire connected to common earth and earth duly incl taking down complete all as specified and as directed.

S&F in replacement of sheet metal VTPN DB TP&N Vertical Loadline MCCB Incomer Loadline DBs are fitted with Bus Bars, Neutral Links, Blanking Plates (without MCCB) G-FRAME MCCB INCOMER DB (Busbar Rating 160 A) 04 way (Optimum+ 12) with metal door 415 volts grade IP 43 Protection Grade fixed flush to wall complete including connections should be provide with necessary reducer lugs all as specified and directed by Engr-in-charge.

S&F in replacement of DPX3 thermal magnetic MCCB 4 pole 160 Amps 415 Volts 25 ka including making necessary arrangement all as specified and directed by engineer in charge for MCCB DB complete all as specifed and as directed.

S&F in replacement of MCCB DB TPN 4 ways, with metal double door CRCA sheet steel Each power coated, IP-43 protection suitable for MCB as out going, 415 volt 3 phase complete with appropriate size copper bus bar and neutral link complete, cutting chases to wall for fixing of DB and making good distrubed wall/surface all as required at site complete all as specified and directed by Engr-in charge.

S&F in replacement of MCB Metalic Distribution board 8 way, double door, 230 Volts concealed flush to wall for mounting MCBs factory made, conforming to IS. 13032 fabricated out of CRCA sheet fitted with DIN channel, neutral link and approriate rated bus bar DBs shall be semi glossy finished with epoxy polyster based powder paint sprayed and backed at high temperature, between powder paint process to ensure smooth finish and protection against corrsion atmosphere. the DBs shall be double door type with hinged door with locking arrangement. The DBs shall be of same make as MCBs, DB shall also be provided with lable marking indicating the incoming and outgoing circuits on all ways as specified, the DBs shall be of IP 43 protection complete all as specified and directed by Engr-in-Charge.

S&F MCB SPN 63 Amps breaking capacity 10kA, C series complete all as specified and as directed.

S&F MCB SP 63 amps breaking capacity 10KA, C Series etc, complete all as specified and as directed.

S&F MCB SP 240 volts, 40 amps, 50HZ, 10 KA, C series complete all as specified and directed

S&F MCB SPN 240 volts, 40 amps, 50HZ, 10 KA, C series complets all as specified and directed.

S&F MCB SP 240 volts, 6 to 32 amps, 50HZ, 10 KA, C series complete all as specified and directed.

S&F Residual Current Circuit Breakers/Earth Leakage Circuit Breakers (RCCBs/ELCBs)- AC Type Double pole 63 amps 30 mA complete all as specified and directed by Engr-in-Charge.

M&L for earthing complete with galvanized steel earth plate electrode of size 60cm x 60cm x 6mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to earth lead by means of bolts nuts and washers of GI and including earthing pit charcoal, common salt, GI 4mm dia lead wire with 20mm GI medium grade watering pipe and 15mm bore light grade protection pipe upto 5 mtr length with wire mesh and funnel, PCC pit in PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregates), angle iron frame and RCC cover and earth work, complete all as shown in electrical plate No. 3 of SSR-2009 (Part-1) and including dismantling existing old earthng, complete all as specified and directed.

Rigid non-metallic PVC conduit of dia 25 mm exclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and foxing accessories such as couplers, lock nuts, saddles, pipehooks etc complete all as specified and as directed.

Supply and laying or fixing or passing through existing duct/pipe, 1100 Volts grade heavy duty XLPE cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armored with galvanized steel wire or tape and over all PVC sheathed 50 Sq mm 3.5 core nominal cross section stranded conductor complete all as specified and directed.

M&L for dry sand cushioning to underground cables provided with a layer of sand 8 cm deep before laying the cable, 15 cm depth after laying cable & stretching the cable all as specified and directed

Supplying and laying un-reinforced precast concrete cable cover, Class LV, Type I, flat, size 250mm x 150mm x 40mm complete all as specified and as directed.

Supply and laying G.I pipe Light grade with all fittings required for protection of under ground cable including cutting of road/flooring surface wherever required and making good to match with existing floor/surface of size 50 mm dia all as specified and directed.

Supply and laying or fixing or passing through existing duct/pipe, 1100 Volts grade heavy duty XLPE cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armored with galvanized steel wire or tape and over all PVC sheathed 6 Sq mm 2 core nominal cross section stranded conductor complete all as specified and directed.

Supply, fixing and testing of LED 9/10 watt post top lantern bollard E bamboo - IP65 generation energy saving environment friendly longl life aesthetically designed Pressure die cast powder coated housing with PC diffuser. Efficient high output LED with IP65 protection suitable for garden ways and heritage sites including necessary electric connection complete all as specified and as directed.

Supply & fix of Junction box/cut-out box/fuse box for single phase/2 core low wattage FTL/CFL based lighting system for pedestrian/ pathway illuminationsintex box of size 200 x 140 x 95 mm(inside demension) Hinged (L) wiith 2 way connector mounted on epoxy insulators for looping of cable for 1Phase and 1neutral fixed on pole/wall with the help of MS nuts bolts and MS clamps-2 Nos of size 40 mm X 4 mm thick with one No MCB SP 6 Amp capacity mounted on din rail inside box. work also includes making suitable hole in wall to take out connections to fitting if required at site and provisioning of 1.0 sqmm 3.0 core flexible PVC insulated copper cable from junction box to conector of gate lights

M/S GURU DEV BUILDERS (BID ID -3186674)