SPL REPAIR/ REPLACEMENT OF OLD CONTROL PANELS INSTALLED AT WATER SUPPLY INSTALLATIONS WITH CONNECTED ITEMS UNDER GE 864 EWS. JOB NO- W/SR -E/M-01/BB CANTT/2024-25

Amount

Supply Installation, Testing and Commissioning of CPRI approved factory made LT panel cubical type of suitable size, 415 Volt, dust proof made out of CRCA sheet 3.15 mm thickness minimum exept inner sheath OG 2 mm powder coated, machine pressed, with provision of rubber beading and locking system, including copper bus bar of suitable capacity, 4 strip mounted on porcelain insulator, bus bar chamber shall be provided with inspection covers each MCCB/cubical switch shall have be independent opening, panel should be mounted on angle iron frame and legs (vertical height of legs not less than 30 cm exept in PCC) made from angle of size 50x50x6 mm, frame and legs duly spray painted internally and externally with two coats of synthetic enamel paint over a coat of red oxide primer legs grouted in PCC 1:2:4, type B-2 (using 20 mm graded stone aggregate) complete including all connection/ control wiring with suitable size of copper conductor cable, including danger notice sticker, comprising the following accessories including testing and taking down old UNSV starter any type complete all as specified :- (a) MCCB 630 Amp 50 KA 4 pole with with spreader Terminals -1 No (Make : Cat No - CM94104OOT1OG of L&T, IHLLSFC40630 of Havells or Cat No LV563320 of Schnider).

Supply Installation, Testing and Commissioning of CPRI approved factory made LT panel cubical type of suitable size, 415 Volt, dust proof made out of CRCA sheet 3.15 mm thickness minimum exept inner sheath OG 2 mm powder coated, machine pressed, with provision of rubber beading and locking system, including copper bus bar of suitable capacity, 4 strip mounted on porcelain insulator, bus bar chamber shall be provided with inspection covers each MCCB/cubical switch shall have be independent opening, panel should be monthed on angle iron frame and legs (vertical height of legs not less than 30 cm exept in PCC) made from angle of size 50x50x6 mm, frame and legs duly spray painted internally and externally with two coats of synthetic enamel paint over a coat of red oxide primer legs grouted in PCC 1:2:4, type B-2 (using 20 mm graded stone aggregate) complete including all connection/ control wiring with suitable size of copper conductor cable, including danger notice sticker, comprising the following accessory including testing and taking down old UNSV starter any type complete all as specified :- (a) MCCB 630 Amp 50 KA 4 pole with spreader Terminals -1 No Make- Cat No - CM94104OOT1OG of L&T, IHLLSFC40630 of Havells or Cat No LV563320 of Schnider.

Supply Installation, Testing and Commissioning of CPRI approved factory made LT panel cubical type of suitable size, 415 Volt, dust proof made out of CRCA sheet 3.15 mm thickness minimum exept inner sheath OG 2 mm powder coated, machine pressed, with provision of rubber beading and locking system, including copper bus bar of suitable capacity, 4 strip mounted on porcelain insulator, bus bar chamber shall be provided with inspection covers each MCCB/cubical switch shall have be independent opening, panel should be monthed on angle iron frame and legs (vertical height of legs not less than 30 cm exept in PCC) made from angle of size 50x50x6 mm, frame and legs duly spray painted internally and externally with two coats of synthetic enamel paint over a coat of red oxide primer legs grouted in PCC 1:2:4, type B-2 (using 20 mm graded stone aggregate) complete including all connection/ control wiring with suitable size of copper conductor cable, including danger notice sticker, comprising the following accessory including testing and taking down old UNSV starter any type complete all as specified :- (a) MCCB 100 Amp 50 KA 4 pole with spreader Terminals -1 No. (Make : Cat No - DZ1F0100NXD1A of L&T, Cat No - IHLFH40100 of Havells or Cat No - LV510487 of Schnider).

Supply Installation, Testing and Commissioning of CPRI approved factory made LT panel cubical type of suitable size, 415 Volt, dust proof made out of CRCA sheet 3.15 mm thickness minimum exept inner sheath OG 2 mm powder coated, machine pressed, with provision of rubber beading and locking system, including copper bus bar of suitable capacity, 4 strip mounted on porcelain insulator, bus bar chamber shall be provided with inspection covers each MCCB/cubical switch shall have be independent opening, panel should be monthed on angle iron frame and legs (vertical height of legs not less than 30 cm exept in PCC) made from angle of size 50x50x6 mm, frame and legs duly spray painted internally and externally with two coats of synthetic enamel paint over a coat of red oxide primer legs grouted in PCC 1:2:4, type B-2 (using 20 mm graded stone aggregate) complete including all connection/ control wiring with suitable size of copper conductor cable, including danger notice sticker, comprising the following accessory including testing and taking out old UNSV starter any type complete all as specified :- (a) MCCB 250 Amp 50 KA 4 pole with spreader Terminals -1 No. (Make : Cat No - CM92106OOP1OG of L&T, Cat No - IHLLNFB40250 of Havells or Cat No - LV525458 of Schnider).

Supply Installation, Testing and Commissioning of CPRI approved factory made LT panel cubical type of suitable size, 415 Volt, dust proof made out of CRCA sheet 3.15 mm thickness minimum exept inner sheath OG 2 mm powder coated, machine pressed, with provision of rubber beading and locking system, including copper bus bar of suitable capacity, 4 strip mounted on porcelain insulator, bus bar chamber shall be provided with inspection covers each MCCB/cubical switch shall have be independent opening, panel should be monthed on angle iron frame and legs (vertical height of legs not less than 30 cm exept in PCC) made from angle of size 50x50x6 mm, frame and legs duly spray painted internally and externally with two coats of synthetic enamel paint over a coat of red oxide primer legs grouted in PCC 1:2:4, type B-2 (using 20 mm graded stone aggregate) complete including all connection/ control wiring with suitable size of copper conductor cable, including danger notice sticker, comprising the following accessory including testing and taking down old UNSV starter any type complete all as specified :- (a) MCCB 100 Amp 50 KA 4 pole with spreader Terminals -1 No. (Make : Cat No - DZ1F0100NXD1A of L&T, Cat No - IHLFH40100 of Havells or Cat No - LV510487 of Schnider).

Supply Installation, Testing and Commissioning of CPRI approved LT panel cubical type of suitable size, 415 Volt, dust proof made out of CRCA sheet 3.15 mm thickness minimum exept inner sheath OG 2 mm powder coated, machine pressed, with provision of rubber beading and locking system, including copper bus bar of suitable capacity, 4 strip mounted on porcelain insulator, bus bar chamber shall be provided with inspection covers each MCCB/cubical switch shall have be independent opening, panel should be monthed on angle iron frame and legs (vertical height of legs not less than 30 cm exept in PCC) made from angle of size 50x50x6 mm, frame and legs duly spray painted internally and externally with two coats of synthetic enamel paint over a coat of red oxide primer legs grouted in PCC 1:2:4, type B-2 (using 20 mm graded stone aggregate) complete including all connection/ control wiring with suitable size of copper conductor cable, including danger notice sticker, comprising the following accessory including testing and taking down old UNSV starter any type complete all as specified :- (a) MCCB 250 Amp 50 KA 4 pole with spreader Terminals -1 No. (Make : Cat No - CM92106OOP1OG of L&T, Cat No - IHLLNFB40250 of Havells or Cat No - LV525458 of Schnider).

Supply Installation, Testing and Commissioning of CPRI approved factory made LT panel cubical type of suitable size, 415 Volt, dust proof made out of CRCA sheet 3.15 mm thickness minimum exept inner sheath OG 2 mm powder coated, machine pressed, with provision of rubber beading and locking system, each MCCB/cubical switch shall have be independent opening, panel should be monthed on angle iron frame and legs (vertical height of legs not less than 30 cm exept in PCC) made from angle of size 50x50x6 mm, frame and legs duly spray painted internally and externally with two coats of synthetic enamel paint over a coat of red oxide primer legs grouted in PCC 1:2:4, type B-2 (using 20 mm graded stone aggregate) complete including all connection/ control wiring with suitable size of copper conductor cable, including danger notice sticker, comprising the following accessory including testing and taking down old UNSV starter any type complete all as specified :- (a) MCCB 63 Amp 50 KA 4 pole with spreader Terminals -1 No (Make : Cat No - DZ1F0063NXD1A of L&T, Cat No - IHLFHF0063 of Havells or Cat No- LV510485 of Schnider)

Supply Installation, Testing and Commissioning of CPRI approved factory made LT panel cubical type of suitable size, 415 Volt, dust proof made out of CRCA sheet 3.15 mm thickness minimum exept inner sheath OG 2 mm powder coated, machine pressed, with provision of rubber beading and locking system, each MCCB/cubical switch shall have be independent opening, panel should be monthed on angle iron frame and legs (vertical height of legs not less than 30 cm exept in PCC) made from angle of size 50x50x6 mm, frame and legs duly spray painted internally and externally with two coats of synthetic enamel paint over a coat of red oxide primer legs grouted in PCC 1:2:4, type B-2 (using 20 mm graded stone aggregate) complete including all connection/ control wiring with suitable size of copper conductor cable, including danger notice sticker, comprising the following accessory including testing and taking down old UNSV starter any type complete all as specified :- (a) MCCB 100 Amp 50 KA 4 pole with spreader Terminals -1 No. (Make : Cat No - DZ1F0100NXD1A of L&T, Cat No - IHLFH40100 of Havells or Cat No - LV510487 of Schnider).

S & F Heavey duty industrial single core PVC insulated round sheathed copper conductor cabe of size 35sqmm (FRLS), cutting to required length connecting with necessary end copper ferrules/luxs drawn through suitable dia flexible PVC pipe including all fixing accessories and taking down old UNSV cable any size/type complete all as specified and directed Make - Havells/Finolex/Polycab

-Ditto- all as per item No 9 but of size 50sqmm.

-Ditto- all as per item No 9 but of size 95sqmm

Supply and lay submersible copper conductor cable 1100 volts grade PVC insulated flexible, PVC sheathed with multistranded copper conductor cutting to required length connecting with necessary end ferrules/luxs/water proof joints of size 3 core 10 sqmm including removing the existing unserviceable old cable any size/type complete all as specified and directed Make - Havells/Finolex/Polycab

-Ditto- all as per item No 12 but of size 3 core 16sqmm.

-Ditto- all as per item No 12 but of size 3 Core 25 Sqmm.

Supply & Installation of Advance encapsulated compound based CPRI tested maintenance free, pipe in-pipe Technology upgraded (Zinc & Alloy Coated), ZINC COATED (80-100) microns with pure Zinc (99.9%) & ALLOY COATING (200-250) microns. Earthing System confirming IS 3034. The outer and inner pipe should be 48.3mm & 26.4mm 2mtrs Length, Zinc coated with additional special Alloy coating 300mm on the topside for additional protection of the Terminal. The annular space between the pipes being filled up with COMPACT FILL (CF) (Crystalline Conductive Compound). The COMPACT FILL (CF) mixture which is machine pressed in the pipes should not disintegrate or collapse when outer pipe corrodes. The inner pipe shall be extended with terminals for connectivity, the job includes digging the pits and refilling the same by Baron Conductolite Back Fill compound (Ground Enhancer), the BFC shall be eco friendly it should not contain environmentally hazardous material/metal having ROHS Certification from NABL accredited lab.

The earth pit should be provided with a FRP or EPCC earth pit cover for protection and safe guard of terminals. In areas where soil condition is bad, G00D EARTH i.e. BLACK COTTON OR MOISTURES NORMAL SOIL is to be arranged to fill the excavated pits by mixing the arranged soil with BFC 3 bags CONDUCTOLITE BFC for installation of earth electrode. As the earth electrode is the main component of the Earthing system which is in direct contact with the ground and thus provides a means of releasing or collecting earth leakage currents. The material should have good electrical conductivity & anti corrosion property in wide range of soil conditions. Model ASEEL 19 (Zinc & AC Coated ) (All the above given dimensions may vary ± 1 MM). OR Make “INDELEC”, “ERICO”, “MACMATE” . For installation of 2m earth electrode 1 Electrode with 3 bags BFC Conductolite to mixed with soil for lowering soil resistivity in excavated pit. 1) The buried Conductors (GI/Copper/ALM) are to be covered by 150mm thick layer of CONDUCTOLITE for additional protection of conductors & better conductivity to lower the resistivity of soil & bring down earth resistance.

M&L for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area laid in trenches / duct or fixed to wall / passing through pipe on pole with suitable size cable glands, crimping type cable lugs for stranded aluminum conductor of size 95 sqmm, 3.5 core including taking down/up old UNSV cable complete all as specified and directed.

M&L for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area laid in trenches / duct or fixed to wall / passing through pipe on pole with suitable size cable glands, crimping type cable lugs for stranded aluminum conductor of size 70 sqmm, 3.5 core including taking down/up old UNSV cable complete all as specified and directed.

M&L for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area laid in trenches / duct or fixed to wall / passing through pipe on pole with suitable size cable glands, crimping type cable lugs for stranded aluminum conductor of size 50 sqmm, 3.5 core including taking down/up old UNSV cable complete all as specified and directed.

M&L for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area laid in trenches / duct or fixed to wall / passing through pipe on pole with suitable size cable glands, crimping type cable lugs for stranded aluminum conductor of size 35 sqmm, 3.5 core including taking down/up old UNSV cable complete all as specified and directed.

Excavation in trenches, not exc 1.5mtr wide and not exc 1.5mtr in depth for foundation, for laying pipe lines etc and getting out in soft/loose soil, complete all as specified and as directed.

Returning, filling in including spreading, leveling and well ramming in layers not exceeding 25 cm thick each, complete all as specified and as directed.

Removing surplus excavated material from site to a distance not exceeding 50 mtrs from starting point and depositing where directed at level not exceeding 1.5 mtr above the starting point, complete all as secified and as directed.

M&L for dry river sand, laid in trenches for cable protection, as 8cm thick below the cable and 15cm thick above the cable, complete all as specified and as directed. Note :- Punned thickness of sand shall be measured & paid.

M&L for sub class 'B' brick covering protection to the eletric cable, laid dry, flat, transversally along the length of cable on sand cushioning with width equal to length of brick, complete all as specified and directed.

M/S M.A.S ELECTRICALS (BID ID -3204052)

M/S VALLEY ENTERPRISES (BID ID -3204305)

m/s mohd saleem and co (BID ID -3202377)