CA No. CE CHZ/CHM/T-03/2025-26 SPECIAL REPAIRS TO CERTAIN BUILDINGS AT DAGSHAI UNDER GE KASAULI

Amount

Demolition of brick or stone masonary built in cement mortar including all quoins arches pillars, roof chimneys at height upto 15 mtr and similar work etc but excluding ashlars facing dressed stone work, precast concrete block etc. and removing debris/ rubbish etc out of MoD land, complete all as specified and as directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern as in roof coverings, claddings in any position or slope upto 15.00 metre height, complete all as specified and as directed.

Dismantling wrought iron, mild steel work (framed or unframed), hard drawn steel wire fabric etc of any description and in any position upto 15.00 metre height not otherwise provided for, complete all as specified and as directed.

Taking down eaves gutters and rain water pipes (any size or pattern) including all fitting heads shoes bends swan necks etc, including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fitting and accessories), complete all as specifed and directed.

Plain cement concrete (1:2:4), type B1 (using 20mm graded mechanically crushed stone aggregate) as in copings to stone masonary, roof kerbs or mud stops, rounded or chamfered on edges, cills, steps, seismic and other similar bands, plinths courses, parapets, bed plates, kerbs slightly rounded or chamfered angles and throating, fixing MS hold fast, filling gaps/spaces between wooden/ mild steel member embedded in stone/ brick masonry wall etc. at height upto 10.00 metre, complete all as specified and directed.

Pre painted galvalume aluminium “zinc coating trapozoidal steel sheet 0.63mm (TCT) of approved colour having tensile strength of 550 MPa as in roof covering, cladding, in any position or slope upto 15.00 metre height, fixed with self tapping screws, complete all as specified and directed.

Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.63mm (TCT) of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and as directed.

Bitumastic gola, with 80/25 bitumen and coarse sand mixture 1:3 by weight, 8cm x 8cm at the junction of roofing to vertical surfaces etc complete all as specified and as directed.

Mild steel works for bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165, complete all as specified and directed.

Plain mild steel sheeting 1.00 mm thick, in valley gutters, drip and straight flashings (length and girth as fixed ), ridges, hips, chimney flashings and similar work etc fixed as welded or soldered joints, reveting are provided etc at height upto 15 mtrs complete all as specified and directed. Note : Rates are included for providing nozzles, stop ends, drop ends made of mild steel sheeting 1.00 mm thick with necessary fixing arrangement/ jointing with rubber sealant for PVC downwater pipes, factory made profiling of flashings.

160 mm dia PVC (SWR) pipes, single or double socketed, in any length with rubber ring joints fixed to wall including necessary heavy duty MS clamps, nuts & bolts, complete all as specified and as directed.

160 mm dia PVC (SWR ) bends (with or without door), elbow etc. with rubber ring joints, fixed to wall, complete all as specified and as directed.

Dismantling boarding or wooden planks, any description, fixed in any position or in any slope or height with nails or screws etc including fillets, complete all as specified and as directed.

2nd class hard wood for 40 mm wrought treads with or without rounded nosings, with 25 mm wrought risers on tongued both edges, glued, wedged and blocked, fixed in repairs, complete all as specified and as directed. Note : Quoted rate is inclusive of necessary cutting/rebating to ends of treads for fixing MS nosing to level flush with treads (width and depth of rebating or cutting as per size of mild steel nosing).

GI Clip in Metal Ceiling plain Globel white colour tiles of size 600 x 600 mm, 0.5 mm thick with 25 mm height, made of GI sheet having galvanizing of 100 gsm/sqm (both side inclusive) , factory painted, 20 % perforation area with 1.8 mm dia holes and having NRC of 0.5 module, which includes providing and fixing 'C' wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm centre to centre, suspending the main C carrier of size 10 x 38 x 10 mm made of GI steel 0.7 mm thick from the soffit with help of soffit cleat 37 x 27 x 25 x 1.6mm, rawl plugs of size 38x12 mm and C carrier suspension clip and mair carrier bracket at 1000 mm c/c. Inverted triangle shaped spring Tee having height of 24 mm and width of 34 mm made of GI steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centres with help of suspension brackets. Wherever the main C carrier and T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in into spring T , The grid is suspended from the roof with min 6 mm GI rods for quick adjustment at max 5000mm length or as per manufacturer instructions, complete all as specifie and directed. Note : The work shall be carried by authorised representative of the manufacturer.

12 mm thick semi perforated micro tegular edged GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of size 595 x 595 mm at all heights of approved texture design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 476 (Part 4) -1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter locking metal T-Grid of hot dipped galvanized iron section of 0.33 mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main T runners of size 15 x 32 mm of length 3000 mm,cross-T of size 15 x 32 mm of length 1200 mm and secondary intermediate cross-T of size 15 x 32 mm of length 600 mm to form grid module of size 600 x 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e. 50mm long, 8 mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 5000mm length and L shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24 x 24 x 0.40 mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws etc., complete all as specified and directed. Note : The work shall be carried by authorised representative of the manufacturer.

8 mm thick seamless calcium silicate ceiling made out of 1800 x 1200mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre fixed with Gl frame work comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre suspended with hangers 6 mm dia G.I. wires (upto 5000 mm length) adjusting level fixed to roof slabs/ wooden truss members by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60 mm long and expansion hold fasteners 12.5 mm dia, 40mm long or fixed with angle cleats including bolts to timber/ mild steel trusses including finishing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seamless finish and applying two coats of oil bound distemper of approved colour over a coat of 1mm thick putty, complete all as specified and directed. Note : The work shall be carried by authorised representative of the manufacturer.

40 mm thick 2nd class hardwood planks as in floors, planed one side, with butt joints and fixed with screws etc to existing floors in patches, including cutting out, piecing, heading joints etc., fixed in repairs, complete all as specified and as directed.

20 mm thick 2nd class hardwood boarding as in roofs, ceilings cladding, flashing, fascia, barge, soffit etc. planed one side, with butt joints and fixed with screws etc to replace old and or decayed boarding in patches including cutting out old, piecing, heading joints etc., fixed in repairs, complete all as specified and as directed.

Preparing surfaces of wood and wood based material, new or old of any description and girth and treated with 2 coats of creosote oil at a height upto 15.00 metre and in any position, complete all as specified and directed.

6 mm thick plywood, grade BWR, type BB, fixed with nails / screws to timber frame etc complete all as specified and directed.

9 mm thick plywood, 5 No of ply, grade BWR, type BB fixed with screws over timber frame work or over existing wooden planks flooring complete all as specified and directed. Note : Rates are included for preparation of existing wooden planks flooring surface plane, smooth and free from any overhead nails or screws etc and filling the uneven surfaces, depressions, holes on existing wooden planks flooring with mixture of sawdust and wood glue before fixing of plywood.

8 mm thick HDF (High Density Fibreboard) direct pressure laminated flooring with abrasion resistance of Class 33/AC-5 conforming to EN13329, density 900 kg/m3, overlay paper of 65 GSM consisting of aluminium oxide coated tissue, Flame resistance CFL-S1 conforming to EN13501 of approved colour/ shade/ texture with wax sealed locking (tongue and groove interlocking) with necessary backing materials required as per manufacturer instructions and laid on existing wooden planks flooring/ PCC flooring, complete all as specified and directed Note : The work shall be carried by authorised representative of the manufacturer.

PVC sheets 2.00 mm thick laminated homogeneous, coloured, marbled mosaic or mottled finish, laid with approved rubber based /synthetic adhesive or as per manufacturer's instructions etc., for fixing over wooden planks flooring complete all as specified and as directed. Note : The work shall be carried by authorised representative of the manufacturer.

Dismantling timber scantling 40 sq.cm and over in section in any position in framed or unframed work etc., complete all as specified and as directed.

2nd class hard wood over 40 sq. cm in scantling clean sawn timber framed and fixed, complete all as specified and as directed.

Dismantling timber scantling 40 sq.cm and under in section in any position in framed work as in fillets, rails, posts, rafters, purlins, etc., complete all as specified and as directed.

2nd class hard wood plain fillets sectional area exc 13 & n.exc 25 sq.cm, square, rectangular or triangular in section, clean sawn, fixed straight or curved, secured with nails or brads etc complete all as specified and as directed.

2nd class hard wood plain fillets sectional area exc 06 & n.exc 13 sq.cm, square, rectangular or triangular in section, clean sawn, fixed straight or curved, secured with nails or brads etc complete all as specified and as directed.

Rolled mild steel section Fe 410-W (Gde E- 250) quality A as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc including cutting and welding complete all as specified and as directed.

Mild steel section framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks, window guard bars, plain, let in and fixed independently in wooden frames including MS screws, L or T section supports for shelves, sinks etc and similar work conforming to Fe.290.Gde-E-165, complete all as specified and directed.

Hard drawn steel wire fabric weight n.exc 4 kg/Sqm cut to lengths, bent to shape required and welded with MS sections or fixed with wooden frame etc., complete all as specified and as directed.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal/ square nut or Mild steel rag or lewis bolts, screwed one end, with hexagonal or square nuts and washers, the other end enlarged and jagged or lewised of any size and length as per site requirment, complete all as specified and directed.

Mild steel plain or chequred plates confirming to Fe-410-W (Gde E-250), quality-A including cutting, grinding the edges and welding, complete all as specified and as directed.

MS Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete or wood and screwing etc. wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, welding etc and similar work conforming to Fe-290 Gde E-165, complete all as specified and directed.

Stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement etc., complete all as specified and directed.

Demolition of PCC in floors, paving, foundation and similar works and removing rubbish / debris out of MoD land etc complete all as specified and as directed.

Broken stone hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n.exc. 15 cm thick, watered and rammed to a true surface complete & all as specified.

Plain cement concrete (1:4:8), type D2 (using 40mm graded mechanically crushed stone aggregate)as in sub base floor, foundations, filling and mass concrete etc complete all as specified and directed.

40 mm thick Cement concrete (1:2:4) type B-1, using 20 mm graded mechanically crushed stone aggregate as in sub - floors, sub bases finished even & rough to receive the topping layer. complete all as specified and directed.

Chequered cement concrete tiles 30cmx 30cm x 25 mm thick, with grey cement and pigment set jointed and pointed in neat cement slurry over and including 20 mm thick screed bed in CM 1:6 in floors with grey cement and pigments etc complete all as specified and as directed.

Demolition of reinforced cement concrete of any description and in any position completely or partly as in beams, staircase, landing, chajjas, cooking platform, water storage tanks base slab etc. and similar suspended work including cutting of reinforcement to facilitate demolition, complete all as specified and directed.

Formwork flat rough finish to chullah hoods, chajjas troughs, cooking/wash basin platform and similar items including edges etc all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, doors and window lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, plinth beams , soffits of slabs supported on walls etc all as specified and directed.

Reinforced concrete nominal mix (1:1.5:3) (using 20mm graded mechanically crushed stone aggregate) as in chajjas, floor/roof beam, plinth beam, cantilevers, floor slabs, door/window lintels, slabs supported on walls, shelves, kitchen platform, washbasin platform etc complete all as specified and directed.

Mild steel TMT bars as in reinforcement 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia.complete all as specified and directed.

Mild steel TMT bars as in reinforcement 6 mm to 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia.complete all as specified and directed.

Brick work with sub class 'B' bricks, class designation 100, old size bricks, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar 1:6 as in walls , foundations, chambers etc, complete all as specified and directed.

Brick work with sub class 'B' bricks, class designation 100, old size bricks, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar 1:4 as in walls , foundations, roof top chimneys at height 15 metre, chambers etc, complete all as specified and directed.

Walling of random rubble uncoursed, well bonded, bedded and solidly hearted , built in cement mortar (1:4) etc complete all as specified and directed

Walling of random rubble uncoursed, well bonded, bedded and solidly hearted except stone, built in cement mortar (1:4) etc complete all as specified and directed

Taking down cement plaster on brick or stone wall, ceilling etc at any height upto 10 metre including racking out joints, hacking for key scrubbing down with water etc to receive new plaster and removing debris/ rubbish etc out of MoD land complete all as specified and as directed.

15 mm thick rendering on fair face of brick-work in CM 1:6 etc finished even and smooth without using extra cement, complete all as specified and as directed.

15 mm thick rendering on stone or surface other than fair face of brick-work in CM (1:4) surface finished even and smooth without using extra cement with @ 200 ml liquid water proofing compound per bag of cement, complete all as specified and directed. Note:-WPC shall be measured and paid separately as supply only.

5 mm thick rendering on fair faces of concrete surfaces as in ceiling, in CM (1:3) and surface finished even smooth without using extra cement complete all as specified and directed.

20 mm thick rendering on stone work or surface other than fair face of brick-work in CM (1:6) finished even and smooth without using extra cement complete all as specified and as directed.

20 mm thick rendering on stone or surface other than fair face of brick-work in CM(1:4) surface finished even and smooth without using extra cement with @ 200 ml liquid water proofing compound per bag of cement, complete all as specified and directed. Note:-WPC shall be measured and paid separately as supply only.

Repairing of damaged RCC Chajja, fascia, fins, roof projection, ceiling and balcony railing etc at any height upto 10.00 metre by rendering 15 mm thick in one or two layers as per site requirement in CM (1:3) finished even and smooth without using extra cement with @ 200 ml liquid water proofing compound per bag of cement with and including hacking out old broken/damaged concrete portion, cleaning of old reinforce etc and applying neat cement slurry @ 3 Kg/Sqm, complete all as specified and directed. Notes:-(i) WPC shall be measured and paid separately as supply only. (ii) Rate for all scaffolding required for repairing work shall be deemed included the quoted the rate.

Supply only liquid water proofing compound ISI Marked, complete all as specified and directed.

Demolition of cement concrete ( unreinforced) roofs, floors (other than ground floors) complete and removing debris/ rubbish etc out of MoD land complete all as specified and as directed.

25 mm thick plain cement concrete (1:2:4) type B-0, using 12.5 mm graded mechanically crushed stone aggregate as in sub base/levelling course on roof surfaces complete all as specified and directed.

10 mm thick rendering or bedding layer on concrete surfaces of roof in CM (1:3) with liquid water proofing compound @ 200 ml per bag of cement, complete all as specified and directed. Note:- WPC shall be measured and paid separately as supply only.

APP polymeric water proofing membrane minimum 3 mm thick and weighting not less than 3.0 Kg/Sqm black finish reinforced with non-woven polyster matt weight not less than 150 gms/Sqm with thermo fusable finish laid over compatible bitumen primer at the rate of 0.40 Ltr/Sqm torching over laps with a propane or butan gas torch with a over lap of 75 mm at the side and 100 mm at the ends and sealing including applying a coat of cold emulsion bituminious primer all as per manufacturers instructions including preparation of surface complete, all as specified and directed. Note:- The water proofing treatment shall be got carried out by the manufactarer or their authorised applicator's duly approved by GE in writing.

Cement concrete tiles 25cm x 25cm x 22mm thick machine pressed set jointed and pointed in neat cement slurry over 15 mm thick layer of CM (1:6), complete all as specified and directed.

75 mm thick PCC (1:3:6) C-2 using 40mm graded mechanically crushed stone aggregate as in path/plinth protection finished even & smooth without using extra cement including filling joints with bituminous monistic filler @ 3 M interval complete, all as specified and directed.

Demolition of cement concrete unreinforced of any description and in any position not otherwise specifically provided for complete, all as specified and directed.

Excavation in trenches in hard/dense soil n. exc 1.50 m wide and n. exc 1.50 m deep and getting out, complete all as specified and directed.

Returning, filling including spreading, levelling and well ramming in layers not exceeding 25 CM in each layer as in hard / dense soil complete, all as specified and directed.

Plain cement concrete (1:2:4), type B-1 (using 20mm graded mechanically crushed stone aggregate) as in surface channels and drains inluding necessary form work as per site condition for providing concrete drains around buildings etc., complete all as specified and directed.

Forming fair finished drain or channel 45 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and directed.

Removing surplus spoil to a distance not exceeding 50 m and depositing where directed at a level not exc. 1.5 m above starting point complete, all as specified and directed.

Taking down chowkhats or frames with shutters(without taking off shutters from the frames) of any description n.exe 1.5 Sqm each including iron mongries, complete all as specified and as directed.

Taking down chowkhats or frames with shutters(without taking off shutters from the frames) of any description exe 1.5 Sqm but n exc 4.00 sqm each including iron mongries, complete all as specified and as directed.

Taking down shutter of any description n exc 1 Sqm each including iron mongries, complete all as specified and directed.

Taking down shutter of any description exc 1 Sqm and n exc 2 sqm each including iron mongries, complete all as specified and directed.

Taking down and refixing shutters of any description n exc 1 sqm each in same opening after making neccessary repair and make the shutter fit for use, complete all as specified and directed. Note : Rates are included for filling of cracks or holes with wood filler, wood glue and saw dust or wood plugs for smooth and even surfaces.

Taking down and refixing shutters of any description exc 1 sqm and n exc 2 sqm each in same opening after making nessary repair and make the shutter fit for use, complete all as specified and directed. Note : Rates are included for filling of cracks or holes with wood filler, wood glue and saw dust or wood plugs for smooth and even surfaces.

Factory made single extruded WPC (Wood Polymer Composite) Solid door/ Window/ Ceosetory windows & other Frames/Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed. Notes : (i) Rates are included for M.S. hold fast/ lugs or SS dash fasteners. (ii) For WPC solid door frames, minus 5 mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made and shade and colour pattern shall be approved by GE/ Engr-in- Charge.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed. Notes : (i) Rates are included for M.S. hold fast/ lugs or SS dash fasteners. (ii) For WPC solid door frames, minus 5 mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made and shade and colour pattern shall be approved by GE/ Engr-in- Charge.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed. Notes : (i) Rates are included for M.S. hold fast/ lugs or SS dash fasteners. (ii) For WPC solid door frames, minus 5 mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made and shade and colour pattern shall be approved by GE/ Engr-in- Charge.

Factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed. Note: stainless steel butt hinges and necessary S.S screws shall be paid separately.

30 mm thick factory made flush shutters (double/single leaf), solid core construction, with particle board core and plywood face panels commercial type on both sides and covered with decorative face veneer complete, as in vision panels or peepholes, square or rectangular including lipping, frame to match etc complete all as specified and directed. Note:- Supplying and fixing of glass shall be measured and paid separately.

Preparation of new or previously untreated surfaces of any description, over 10 cm in width or girth, sizing, applying wood filler liquid transparent and staining with spirit etc., complete all as specified and directed.

Preparation of surfaces of any description, width or girth including cleaning and preparing the surface and applying two coats of polyurethane polishing over a coat of sealer for glossy finish surface as per manufacturer's instruction complete all as specified and directed.

30 mm thick factory made flush shutters (double/single leaf), solid core construction, with particle board core and plywood face panels commercial type on both sides, complete all as specified.

0.9 mm thick decorative laminates type I, or surface finish, colour and pattern as approved with adhesive etc complete all as specified and directed.

30 mm thick 2nd class hard wood partly or fully glazed and skelton shutter open rebated and prepared to receive glass, gauge etc. divided into squares with plain, chamfered or rounded, mitred beads, rebated sash bars any numbers for securing glass, etc or partly with panels of 9mm BWP commercial ply etc with size of members of shutters as specified in SSR Part-I, Section 8 clause 8.24(a) or to match with existing shutters etc supplied and fitted to chowkats, complete all as specified and as directed.

30 mm thick 2nd class hard wood glazed and skelton shutter open rebated and prepared to receive glass ,gauge etc divided into squares with plain, chamfered or rounded, mitred beads for securing glass, etc for windows, ventilators etc are provided with stiles and rails as specified in SSR Part-I, section 8 clause 8.24(b) or to match with existing shutters etc supplied and fitted to chowkats etc complete all as specified and as directed.

Factory made Pressed steel frames, confirming to IS, having profile 125 x 60 mm , 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, and fixing only 100 mm size hinges, lock strike plate, etc., with one shop coat of zinc chromate primer and fixing complete all as specified and directed by Engineer-in-Charge. Note: Butt hinges shall be measured and paid separately as supply only under relevant item.

2nd class hardwood as in plain, solid straight chowkats and frames wrought framed rebated on the solid, rounded or chamfered put together with glue pinned at joints, complete all as specified and as directed

2nd class hardwood as in small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary' labours; articles(including screws, nails, hinges etc to fix with door or window frame) n exc 200 cu.cm each, fixed in repairs, complete all as specified and as directed.

Factory made box type Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded including one shop coat of zinc chromate primer and two coats of approved colour synthetic enamel paint after fixing to frame etc., complete all as specified and as directed. Note: Glass or wiremesh shall be measured paid separately.

Aluminium power coating of approved colour (Thickness or powder coating not less than 50 micron) frame for doors, windows, ventilators, partitions incl necessary joining cleats, rubber packing, snap beading, glazing clips for fixing glass etc with one or more rebates or double/ triple track channels for sliding shutter windows including joining cleat and steel screw for fixing frame to walls/jambs etc. complete all as specified and directed.

Aluminium power coating of approved colour (Thickness or powder coating not less than 50 micron) window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150 mm long (1 No.), hinges type B-21,100 mm long (2 Nos.), aluminium handle (1 No.) etc or sliding shutters with all necessary fittings such as roller, rubber beading locking arrangement clit etc. complete all as specified and directed Note: Glass or wiremesh shall be measured paid separately.

Aluminium power coating of approved colour (Thickness or powder coating not less than 50 micron) window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, aluminium snap beading, screws etc. complete all as specified

Aluminium power coated (Thickness or powder coating not less than 50 micron of approved colour) door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, aluminum snap beading screws etc. complete all as specified and directed.

9 mm thick pre-laminated particle board exterior grade, both side laminations of approved colour and pattern fixed to wooden / aluminium frame work as in partitions, doors etc including necssary fittings etc complete all as specified and as directed.

12 mm thick pre-laminated particle board exterior grade, both side laminations of approved colour and pattern as in pelmet boxes or in narrow width n exc 15cm each, rebated or flat edged etc complete all as specified and as directed.

Fancy type decorated stainless steel curtain hanging rails/rods of 25mm dia having wall thickness 1.6mm inlcuding adjustable SS brackets and SS decorative end caps or finials for each window and door etc. complete all as specified and directed.

Stainless steel 100 mm long butt hinges medium weight and fixed with stainless steel screws, complete all as specified and directed.

Stainless steel 200mm long barrel tower bolt and fixed with stainless steel screws, complete all as specified and as directed.

Stainless steel 100 mm long barrel tower bolt and fixed with stainless steel screws, complete all as specified and as directed.

Stainless steel with glossy finish 'D' type 200 mm long handles and fixed with stainless steel screws complete all as specified and as directed.

Stainless steel 150 mm long handles and fixed with stainless steel screws complete all as specified and as directed.

Stainless steel 100 mm long handles and fixed with stainless steel screws complete all as specified and as directed.

Stainless steel 200 mm long sliding door bolts, plate type, with bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate etc complete all as specified and directed

Stainless steel 300 mm long sliding door bolts, plate type, with bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate etc complete all as specified and directed

Stainless steel 200 mm long barrel tower bolt and fixed with stainless steel screws, fixed in repairs, complete all as specified and as directed.

Stainless steel 150mm long handles and fixed with stainless steel screws, fixed in repairs, complete all as specified and as directed.

Stainless steel 300mm long sliding door bolts, plate type, with bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate etc., fixed in repairs, complete all as specified and directed

Floor door stopper of aluminium alloy body and tongue , anodised with hard drawn steel spring over all length of cover plate 150mm complete all as specified and directed.

Floor door stopper of brass body and tongue , anodised with hard drawn steel spring over all length of cover plate 150mm complete all as specified and directed.

Mild steel 375mm ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and directed.

Aluminium (extruded section body) hydraulically regulated designation No. 3 universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg and fixed, complete all as specified and directed.

Kicking plates, any size, of galvanised iron sheet 1mm thick, fixed with galvanised screws, complete all as specified and directed.

Securing glass, as in repairs, of any description in existing wooden frames glazed with putty/ beads including removing loose or decayed putty/beads, painting/oiling one coat on rebates, grooves, reputtying and painting/oiling puttied surface to match existing work etc., complete all as specified and directed

1st class hardwood Beads, straight (any size) for glazed or gauzed joinery, renewed, including mitres including fixing with nails etc and removing old beads to store, complete all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and as directed

4.80 mm thick Sheet glass, ordinary quality and glazing with oil putty or fixing in aluminium shutters/frames in any shape and size complete all as specified and as directed.

4.80 mm thick obscured or frosted glass, ordinary quality and glazing with oil putty or fixing in aluminium shutters/frames in any shape and size complete all as specified and as directed.

6.00 mm thick obscured or frosted glass, ordinary quality and glazing with oil putty or fixing in aluminium shutters/frames in any shape and size complete all as specified and as directed.

15mm thick toughned glass as in hinged doors, partitions automatic doors, semicircular/arched transom portion of doors, windows & for opening more than 1.5 metre width and similar work including cutting to shape, drilling holes as required etc complete all as specified and directed. Note : Rates are included for provision of rubber packing/gasket, fins, hinges, brackets, glass studs etc as per site requirement.

Logo printed self adhesive PVC glass film of any thickness in plain/ frosted/ coloured as approved by Engineer-in-Charge etc complete all as specified and directed

2 mm thick plain/textured flexible crystal clear/frosted polycarbonate plain sheets, including cutting to required shape and size as in openings of terraces, balconies, verandahs, windows and similar work fixed on timber frame or MS frames with self driving screws etc complete all as specified and directed

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or nails, fixed in repairs, complete all as specified and directed.

18mm/19mm thick plywood, grade BWP, type BB with 0.9mm thick decorative choice lamination on both sides of approved colour and pattern fixed to aluminium frame work as in door/partitions or fixed with screws for cupboard shutter and similar work etc., fixed in repairs, complete all as specified and as directed.

PVC edge strip of 18/19 mm wide, colour and pattern as approved fixed with adhesive as per specified and as directed

Continuous (piano) hinges, mild steel, bright finish or electrogalvanised bright finish width of flaps (when open) 30 mm complete all as specified and as directed.

Stainless steel hasp & staple 100mm inluding bolt to hinge plate and fixed with screws complete all as specified and directed.

Preparation of new/ old plastered surfaces of walls and applying 2.00 mm thick wall care putty in two layers of 1.00 mm thick each layer and sanding with sandpaper to remove any loose particles, unevenness, wrinkles to achieve a smooth and even surface for further coating, complete all as specified and as directed.

Preparation of surfaces of wall and applying two coat of oil bound distemper over surfaces prepared with wall care putty, complete all as specified and as directed. Note: Item of wall care putty shall be measured and paid separately.

Preparation of old plastered surfaces of wall by complete removal of existing treatment with mechanical scrapper including washing, rubbing down dust and loose particles and applying two coat of oil bound distemper over surfaces prepared with wall care putty, complete all as specified and as directed. Note: Item of wall care putty shall be measured and paid separately.

Preparation of surfaces of walls and applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over surfaces prepared with wall care putty, complete all as specified and as directed. Note: Item of wall care putty shall be measured and paid separately.

Preparation of old plastered surfaces of wall by complete removal of existing treatment with mechanical scrapper and applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over surfaces prepared with wall care putty, complete all as specified and as directed. Note: Item of wall care putty shall be measured and paid separately.

Preparation of new plastered surface of wall and applying two coat of cement base paint over a coat of primer on walls complete all as specified and directed.

Preparation of new plastered surfaces on ceilings of any height and apply three coats of white wash on plastered surfaces of ceiling complete all as specified and directed.

Preparation of new steel surfaces of any description over 10 cm in width or girth not other wise described and applying two coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and as directed.

Preparation of new steel surfaces of any description not exc. 10 cm in width or girth not other wise described and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and as directed.

Preparation of old steel surfaces of any description over 10 cm in width or girth not other wise described and applying one coat of synthetic enamel paint, complete all as specified and as directed.

Preparation of new wooden surfaces of any description over 10 cm in width or girth not other wise described and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed.

Preparation of new wooden surfaces of any description n exc 10cm in width or girth not other wise described and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed.

Preparation of old painted wooden surfaces of any description over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint all as specified and directed.

Demolition of stone slab and tiles of any description or thickness in floors aprons etc laid bedded and pointed in any mortar etc and removing debris/ rubbish etc out of MoD land complete all as specified and as directed.

Struking of existing PCC floor surface 5 to 10 mm deep picking, sweeping, clean and washing down with water to remove dust to receive cement mortar for tiling complete all as specified and directed.

Machine cut Kota stone slab flooring 18-22 mm thick, for staircase step in single piece (of length not more than 1200 mm), laid over & including 15 mm thick (average thickness) cement mortar (1:3) screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (mirror finish) complete, including provn of two Nos 3x3mm grooves at tread of each step complete all as specified and as directed by the Engr-in-Charge.

Machine Cut Kota stone slab 18-22 mm thick on vertical surfaces like riser of steps, skirting, in single piece (of length not more than 1200 mm) over & including 10 mm thick (average thickness) cement mortar (1:3) rendering and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (Mirror finish), complete all as specified and directed by the Engr-in-Charge.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and removing debris/ rubbish etc out of MoD land complete all as specified and as directed.

Glazed ceramic coloured tiles 450mm x 300mm & 7mm thick on vertical surface such as skirting , dado etc. over and including 10 mm thick rendering in CM 1:4 thick set and jointed in neat cement mortar and pointed in white or colour cement to match tiles complete all as specified and directed by Engineer-in-Charge.

Non skid ceramic, joint less, coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement mortar over and including 15 mm thick screed in cement mortar (1:6) and pointed in white or coloured cement to match the tiles complete all as specified and directed by Engineer-in-Charge.

18-20 mm thick Granite (of any type) work ( table rubbed and polished) in steps, jambs, window cills, cooking platform, wash hand basin , urinal partition etc and like fixed to wall in verticle position laid over 10 mm thick rendering/screed bed in CM 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite to match the shade of the slab and rounding of edges complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, including making hole by drilling for gas pipe and other similar situations all as specified and directed

Disconnecting existing tanks of capacity exc. 250 & n. exc. 500 litre, and removing to store complete all as specified and directed.

Disconnecting existing tanks of capacity exc. 500 & n. exc. 1000 litre, and removing to store complete all as specified and directed.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning etc and hoisting if required reconnecting and re-fixing in same or different position or place etc complete all as specified and directed.

Rotational moulded polyethylene water storage tanks 1000 Ltr capacity (cylinderical vertical with closed top), hoisted and fixed in position all as specified in SSR Part 1, complete all as specified & directed.

Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed ( Minimum weight 20mm-210gm) 20 mm bore, complete all as specified and directed

Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed ( Minimum weight 20mm-210gm) 20 mm bore, fixed in repairs, complete all as specified and directed.

15 mm dia gun metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed in repairs, complete all as specified and directed.

20 mm dia gun metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed in repairs, complete all as specified and directed.

Taking up or down steel tubing and connections of 15 mm bore in pipe, including cleaning for re-fixing or removal from site to store complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing and connections of 20 mm bore in pipe, including cleaning for re-fixing or removal from site to store complete all as specified and directed by Engineer-in-Charge.

Steel water tubing, galvanised, medium grade, ISI marked, 15 mm bore with and including all fittings (elbows, Tee, sockets, union, plugs, reducers etc) , cutting, threading and fixed to walls or fixing in concealed walls or laid in floors and making good the surfaces to match the existing ones complete all as specified and directed by Engineer-in-Charge.

Steel water tubing, galvanised, medium grade, ISI marked, 20 mm bore with and including all fittings (elbows, Tee, sockets, union, plugs, reducers etc) , cutting, threading and fixed to walls or fixing in concealed walls or laid in floors and making good the surfaces to match the existing ones complete all as specified and directed by Engineer-in-Charge.

Cutting chases, pinning in stone walls/ concrete block/ slab and making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth,complete all as specified and as directed.

75 mm bore PVC(SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors, fixed in repairs, complete all as specified and as directed.

110 mm bore PVC(SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors, fixed in repairs, complete all as specified and as directed.

110 mm bore PVC(SWR) pipes single socketed, in any length with rubber ring joints fixed to walls including necessary heavy duty MS clamps, nuts & bolts, fixed in repairs, complete all as specified and as directed.

75 mm bore PVC (SWR) bends any radius and jointing, fixed in repairs, complete all as specified and directed.

75 mm bore PVC (SWR) bends with access doors any radius and jointing, fixed in repairs, complete all as specified and directed.

110 mm bore PVC (SWR) bends any radius and jointing, fixed in repairs, complete all as specified and directed.

110 mm bore PVC (SWR) bends with access doors any radius and jointing, fixed in repairs, complete all as specified and directed.

75 mm bore junction single (Single T) equal or unequal and jointing, fixed in repairs, complete all as specified and directed.

110 mm bore junction double (Double T) equal or unequal and jointing, fixed in repairs, complete all as specified and directed.

110 mm bore PVC(SWR) vent cowl, fixed in repairs, complete all as specified and as directed.

75 mm bore PVC(SWR) floor/ nahani trap, with CP grating including jointing with solvent cement, fixed in repairs, complete all as specified and as directed.

110 mm bore PVC(SWR) 'P' trap including jointing with solvent cement, fixed in repairs, complete all as specified and as directed.

Precast cement concrete 1:2:4, type B1 (Using 20 mm graded stone aggregate) in landings, cover slabs (for manholes etc.) shelves and similar articles with plain faces and set in cement mortar 1:4 including dismantling or demolition of old manholes cover, gratings, gully traps etc and removing of debris out of MoD land complete all as specified and directed. Note : (i) Reinforcement & MS handles for cover slab shall be measured and paid separately (ii) Quoted rates are inclusive of fixing FI 75 x 6mm alround cover slab and welding with slab reinforcement including supply and fixing of PVC/MS pipes of 20/15mm internal bore for cover slab MS handles (02 Nos each slab) before casting.

Cast iron work grade FG 150, unmatched, in brackets, gully traps, grating, railing, frames, manhole covers and frame double seal type etc including setting in cement mortar (1:3) and flaunching with cement concrete (1:2:4), type B1, light duty any type and size , including dismantling or demolition of old manholes cover, gratings, gully traps etc and removing of debris out of MoD land complete all as specified and directed

PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement, fixed in repairs, complete all as specified and directed

Bib taps, cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down, fancy type, long body, screwed for iron pipe or for brass ferrule and fixed for 15 mm bore pipe, fixed in repairs, complete all as specified and directed.

Pillar taps , cast copper alloy, with capstan heads, chromium plated,fancy type screwed down high pressure, with or without lettered 'Hot' or 'Cold' withlong screwed shanks and fly-nuts, screwed for iron pipe and fixed of 15mm bore, fixed in repairs, complete all as specified and directed by Engr–in–Charge.

Brass chromium plated WHB Mixer, swan neck type, for mixing hot and cold water screwed down for 15mm dia iron pipe, fixed in repairs, complete all as specified and directed by Engineer-in-Charge.

Brass chromium plated Wall Mixer, long body, for mixing hot and cold water screwed down for 15mm dia iron pipe complete all as specified and directed by Engineer-in-Charge.

Brass chromium plated Sink Mixer, swan neck type, for mixing hot and cold water screwed down for 15mm dia iron pipe complete all as specified and directed by Engineer-in-Charge.

Sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm with plugs, washers, waste coupling and PVC waste pipe ; including bedding in cement mortar to dwarf wall or fixing cantilever brackets and connecting union to pipe, fixed in repairs, complete all as specified and directed.

15mm bore angle cock cast copper alloy chromium plated fancy plate screwed down high pressure with crutch or butterfly handle, fixed in repairs, complete all as specified.

Vitreous China wash hand basin white with full pedastal flat back size 630x450 mm, including fixing brackets and PVC waste pipe with coupling, cutting for and pinning in ends of brackets or errecting stand, fixed in repairs, complete all as specified and as directed.

Vitreous china counter wash hand basin, size 630 x 450 x 290mm (Make : CERA Cat No : S2090101 or eqivalent) , snow white with provision of overflow and tap hole including fixing brackets and waste pipe with coupling, cutting for and pinning in ends of brackets or errecting stand, complete all as specified and as directed.

Vitreous china wash down water closet pan (pedestal pattern), white, with and including plastic water closet seat, white, closed pattern with flat bottom and cover, stainless steel toilet seat/ commode jet spray with miniumum 1 mtr length flexible pipe and mild steel chromium plated or aluminised hinging device (excluding flushing cistern and flush pipe), including connection to drain (or outgoing pipe) and to flushing pipe, anti -syphonage pipe, etc., fixed in repairs, complete all as specified and directed.

Toilet paper holder with flat recessed type stainless steel, complete all as specifed and directed

Vitreous china squatting pan (Orrisa pattern), white, size 680 x 470mm with integral foot rest (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, anti- syphonage pipe including trap set in concrete, fixed in repairs, complete all as specified and directed.

10 ltr capacity PVC valveless syphonic action type, flusing cistern, low level, white, with inlet, ball valve, float and handle including brackets fixed etc including PVC flushing pipe 32mm dia, fixed in repairs, complete all as specified and as directed.

Health faucet, cast brass alloy, chromium plated with gun, minimum 1mtr long easy flex tube, bracket wall mounted including making connections and fixed in position complete in all respect as specified.

Vitreous China urinals, half stall (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe, fixed in repairs, complete all as specified and as directed.

Urinal spreader of copper alloy chromium plated for fixing with 15 mm dia pipe etc complete all as specified and directed.

Viterous china urinal partition white of size 310 x 700mm terminating about 40cm above floor line, fixed in repairs, complete all as specified and directed.

Stainless steel grating doom 125 mm dia with or without waste hole as per site requirement, complete all as specified and directed.

Stainless steel grating doom 100 mm dia with or without waste hole as per site requirement, complete all as specified and directed.

PVC connections 15mm size with PTMT nuts of length 450mm, fixed in repair, complete all as specified and directed by Engineer-in-Charge.

Frameless rectangular 6mm silver looking mirror with smooth curved edges wall mounted of size 18 x 24 inches (Make : Saint gobain or modiguard, Model : FG-RECT-1824) with pre-fitted steel star hooks, fixed in repairs, complete all as specified and as directed

Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60 cm long, complete all as specified and as directed.

Towel rail 600mm long of chromium plated fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 190 gms), complete all as specified and as directed.

Soap dish fixed to plugs with chromium plated brass screws, complete all as specified and as directed.

Forming letters, figures etc by cutting 'V' grooves in cement plaster (per cm of height), complete all as specified and directed.

Writing letters or figures (block, roman, italic or Indian) with two coats of black paint n exc 30 cm high for building numbers, complete all as specified and directed

Taking down copper/aluminum point wiring any type / size complete with removing all connection and accessories such as switches, sockets, ceiling rose, pendent holder, fan regulator any type, all type of tube light fitting, bldg security light batten, steel or PVC conduit , casing caping etc. complete and making good the disturbed surface of wall , floor etc.complete all as specified and as directed by Engr-in-charge. Notes :- (i) Rates for cutting/chasing in wall and making good deemd to be included in quoted rate of this item. (ii) Serviceable tube light fittings shall be reused.

Point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor drawn through and including medium grade, ISI marked, PVC conduit medium grade ISI marked not less than 20 mm dia with accessories, concealed/surface type on wall/ceiling and including provision of 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including pressed steel terminal boxes suitable for modular covered plate over sunken box for housing the modular switches , socket outlets, fan regulators etc. with brass screws and brass washers and making good the disturbed surfaces as per existing for the following :- Notes:- (i) Metal flush/sunken Box, modular switch/socket cover plate & sheet are inclusive in the item rate quoted. (ii) Only switches, socketes and fan regulators to be measured and paid seperately.

(a) One light point /fan point/Exhaust fan point/bell point controlled by one, one way switch and fan regulator.

(b) socket outlet 3 pin, 5 Amp on independent board.

(c) Socket outlet, 3 pin,5 Amp on the same board with other switches.

All as per item No. 209 here-in-before but 4.0 sqmm single core multi stranded copper conductor PVC insulated unsheathed (FRLS-H) cable 1100 volts incuding 4.0 sqmm stranded copper conductor (FRLS-H) PVC insulated green in colour as continous earth conductor connected to common earth and earth dolly with all accessories for one 5 pin 16 Amp socket (Power point) on independent board complete all as specified and directed.

Taking down carefully unserviceable Sub main wiring of any size and type, removing material from site for taking credit and making good the disturbed surfaces of walls, ceilings etc including two coats of white / colour washing / distempering etc to match the existing complete all as specified and directed by Engineer - in - Charge.

Submain wiring with 2 (Two) single core PVC insulated & PVC unsheathed FRLS-H cable 1100 Volt grade with 4.0 Sqmm copper multistranded conductor drawn through and including PVC conduit medium grade of appropriate size concealed in walls/ceilings/roofs including 4.0 Sqmm single core multistranded copper conductor 1100 V grade PVC insulated and unsheathed FRLS-H cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed.

Submain wiring with 2 (Two) single core PVC insulated & PVC unsheathed FRLS-H cable 1100 Volt grade with 6.0 Sqmm copper multistranded conductor drawn through and including PVC conduit medium grade of appropriate size concealed in walls/ceilings/roofs including 6.0 Sqmm single core multistranded copper conductor 1100 V grade PVC insulated and unsheathed FRLS-H cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed.

Submain wiring with 2 (Two) single core PVC insulated & PVC unsheathed FRLS-H cable 1100 Volt grade with 10.0 Sqmm copper multistranded conductor drawn through and including PVC conduit medium grade of appropriate size concealed in walls/ceilings/roofs including 10.0 Sqmm single core multistranded copper conductor 1100 V grade PVC insulated and unsheathed FRLS-H cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed.

Submain wiring with 2 (Two) single core PVC insulated & PVC unsheathed FRLS-H cable 1100 Volt grade with 2.5 Sqmm copper multistranded conductor drawn through and including PVC conduit medium grade of appropriate size concealed in walls/ceilings/roofs including 2.5 Sqmm single core multistranded copper conductor 1100 V grade PVC insulated and unsheathed FRLS-H cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed. Notes for item Nos. 212 to 215 : - (i) Two runs of main cable, one run of earth continuity conductor and one run of conduit will be measured and paid as one length only. (ii) The cost of cutting chases for concealing PVC conduit shall be deemed to be included in quoted lump sum of Schedule 'A' Section-I.

Modular switch one way 6A, 1 module, 240 volts, complete all as specified.

Modular switch one way 16 Amps, 1 module, 240 volts, complete all as specified.

Modular socket 6 Amps-2/3 pin combined, 2 module, 240 volts, complete all as specified.

Modular socket 6A/16A-2/3 pin combined, 2 module, 240 volts, complete all as specified.

Modular bell push 6 Amps, 1 module, 230 volts, 240 volts, complete all as specified.

Ceiling rose surface mounting type, polycarbonate, isolated body, 65x50mm, 3 terminal fixed on & including PVC block complete all as specified and directed.

Lamp holder , PVC/Polycarbonate type with back plate modular type complete all as specfied and as directed.

Wall Surface Mounted General Purpose 18 Watts, LED Batten in Extruded Aluminium having THD < 10% fixed in repair incl making all necessary connection from ceiling rose to light fittings, complete all as specified.

Fixing only in wall Surface Mounted General Purpose 18 Watts LED Tube light fitting retrived from Item No. 208 above in and including making all necessary connection from ceiling rose to light fittings, complete all as specified.

Recess/ surface/ suspended mounting 36W Ultra modern designed architectural 2'x2' LED luminaire which provides soft-light and glare free symmetrical illumination, including all accessories for fixing in false ceiling/ceiling/in hanging position complete all as specified and directed by Engr-in-Charge.

Walls Surface Mounted general purpose 10 Watts, LED Batten in extruded aluminium fixed in repair incl making all necessary connection from ceiling rose to light fittings complete all as specified and directed.

Surface mounted LED bulk head 10 watt luminaire with ABS body & polycarbonate diffuser IP 65 including connecting to ceiling rose with 0.5 sqmm two core copper flexible conductor cable complete all as per specified and directed.

Building security Lights of 35W with best in class design & Robust heat sink 6500k along with class leading IP 65 & Surge protection including provision of 1 No GI tube medium grade 25mm bore bracket of total length 50 cm incl 2 Nos MS Clamp and fastners, complete all as specified and directed.

Self ballasted LED Retrofit Bulb, 5 Star Bulbs 12 Watt with PBT body shell and PC diffuser. 210 degree wide distruction CCT 6500K, B-22 cap, (Pin type), 230V, PF-0.95 (min), complete all as specified and as directed.

Taking down carefully unserviceable distribution board of any capacity including MCCB, MCBS, wooden board and making good the disturbed surfaces of walls, etc including two coats of white / colour washing / distempering etc to match the existing complete all as directed by Engineer - in - Charge.

VTPN DB 4 way, vertical loadline type, double door, IP 42, CRCA sheet powder coated vertical type factory made suitable for incorporating MCB as out going and MCCB as incomer including connecting incoming and outgoing cables & blanking plate as required and making good distrubed surface to match with existing complete all as specified and as directed. Note : Make of MCCBs and MCBs shall be same as of DBs.

DB SPN 8 way double door, IP 42, CRCA sheet powder coated factory made suitable for incorporating MCB as out going connecting incoming and outgoing cables & blanking plate as required and making good disturbed surface to match with existing, complete all as specified and as directed.

DB SPN 4 way double door, IP 42, CRCA sheet powder coated factory made suitable for incorporating MCB as out going connecting incoming and outgoing cables & blanking plate as required and making good disturbed surface to match with existing, complete all as specified and as directed.

MCCB 4 Pole, 100 Amps, 16 KA, 415 Volt, complete all as specified and as directed.

MCB, SPN, 6 to 32 Amp, 240 Volts, 10 KA, 'C' curve, complete all as specified.

MCB, SP, 6 to 32 Amp, 240 Volts, 10 KA, 'C' curve, complete all as specified.

Heating Element ISI Marked round/ tringular base, push type or thread type including rubber washer for 1.5/2.0 KW suitable for geysers 25 Ltrs to 50 Ltrs capacity (as per existing sample) including taking down unserviceable complete all as specified and as directed.

Thermostat ISI Marked suitable for geysers 25/50 Ltrs capacity (as per existing sample) including taking down unserviceable complete all as specified and as directed.

Chromium plated connections 45 Cm long for Hot/Cold water of 15mm size with cromium nuts and washers complete all as specified.

Single pole and neutral enclosure with a two pin and earth plug with socket complete with one double pole MCB 20 Amps,240 Volts single phase complete all as specified and directed.

Taking down the geyser of 25/ 50 ltr capacities from the site after disconnecting the water connection, electric connection, opening the geyser assembly and descaling the deposited impurities in the inner container and outlet water pipe set and refix on the wall with suitable size fastener 4 Nos each complete all as directed by Engineer-in-Charge. Note:- All items required for replacement of unserviceable bolts, rubber real, ring nuts, washers shall be included in the quoted rate itself.

Bell Ding Dong AC 230V, single pole electronic complete all as specified and directed.

Plain cement concrete (1:2:4), type B1 (20 mm graded mechanically crushed stone aggregate) as in foundation, filling, mass concrete, hard standing etc. including necessary form work and finishing surface even and fair without using extra cement complete all as specified.

Exhaust fan, PLASTIC body, heavy duty, AC single Phase 230V of size 300 mm sweep with, blades, and frame and louvers including taking down unserviceable exhaust fan, complete all as specified and as directed.

Exhaust fan, steel body, heavy duty, AC single Phase 230V of size 300 mm sweep with, blades, and frame and louvers including taking down unserviceable exhaust fan, complete all as specified and as directed.

Exhaust fan, steel body heavy duty AC single Phase 230V of size 380mm sweep with, blades, and frame and louvers including taking down unserviceable exhaust fan, complete all as specified and as directed.

Taking down old unserviceable earthing by disconnecting the existing and making good the disturbed surfaces of floor to match the existing complete all as specified and directed by Engineer - in - Charge.

Earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5m below the normal ground level connected to galvanised earth lead of 4mm dia GI wire by means of bolts, nuts, check nuts and washers of galvanised iron.Earth wire protected by GI pipe 15mm bore(medium grade) and connected to main switch board or main control board complete and shown in electrical plate No. 3 of SSR Part I (2009) including necessary concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 40 cement mortar x 40cm x 5cm reinforced with 8mm dia TMT bars @ 15cm C/C with one handle for lifting made out of 8mm dia bar, funnel, wire mesh, 20mm dia GI pipe medium grade for watering, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil and testing complete and as directed by Engineer-in-Charge.

Dismantling taking out carefully old/unserviceable UG cable of any type/ size from trenches/pole/duct/LT panel after disconnecting from OH conductors/MCCBs/joint boxes for relaying/refixing or carrying to store for Sch of credit.

GI tubing, light grade, 50mm bore, ISI marked, for cable protection at road crossing complete all as specified and directed.

Double walled corrugated HDPE duct pipe of 50 mm outer dia confirming to IS-14390(Part-II) of approved colour with fittings for cable protection complete all as specified.

Service cable passing through pipe testing and commissioning of 1100 Volts grade 'Heavy duty' PVC sheathed armoured cable LT, XLPE insulated aluminium conductor multi stranded served with inner sheating of PVC tape armored with galvanised steel wire or tape and overall PVC sheathed of size 25 Sqmm nominal cross sectional area 3.5 core with suitable glands and lugs as per site requirement confirming to IS specifications, complete all as specified and directed .

Service cable passing through pipe testing and commissioning of 1100 Volts grade 'Heavy duty' PVC sheathed armoured cable LT, XLPE insulated aluminium conductor multi stranded served with inner sheating of PVC tape armored with galvanised steel wire or tape and overall PVC sheathed of size 35 Sqmm nominal cross sectional area 3.5 core with suitable glands and lugs as per site requirement confirming to IS specifications, complete all as specified and directed .

Sch of Credit

M/S SHANTI SARUP DINESH CHAND (BID ID -3339637)

A P ENTERPRISES (BID ID -3339252)

m/s jupiter builders (BID ID -3339721)

R B TRADERS (BID ID -3339701)

PAWAN KUMAR (BID ID -3335560)

M P TYAGI ENGINEERS AND CONTRACTORS (BID ID -3336636)

Shri Balaji Construction (BID ID -3338727)

mohanlal gupta (BID ID -3338885)

M/s JAIMAA ASSOCIATES (BID ID -3338138)

M/S SURAT SINGH AND SONS (BID ID -3339958)

M/S Yamin (BID ID -3335756)