COMPREHENSIVE B R AND E M MAINTENANCE OF BLDGS OF ZONE B UNDER AOR OF B R 1 AT HISAR MIL STN UNDER GE WEST HISAR

Demolition of cement concrete(unreinforced)/ lime concrete as in sunken portion / ground floor exceeding 15cm thickness including removing rubbish complete all ass specified and directed.

M & L 10 mm thick rendering in CM 1:4 on faces of sunkan portion(floor and side ) with smooth finishes using water proofing compound

M&L P:C:C 1:7:12 as in mass concrete using 40 mm graded brick agg as in sunken portion and other location as required all as spd and dir by engg-in-charge

M&L for cement concrete 1:2:4 type B-1(using 20 mm graded crushed Stone agg) as in sunken portion /padding leveling course providing necessary slope including WPC complete all as specified and directed.

S&F, PVC Floor trap 75mm bore with grating incl jointing using solvent cement to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as directed

Dismantling 75mm dia and upto 150mm dia drain of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required complete all as specified and directed

S&F, 110mm dia PVC bend any radius all as specified.

S&F PVC (SWR) pipes 110 MM bore single socketed in any length with rubber ring joints fixing done with pipe supporting clamping system consists of Profile Bracket + Continuous Slotted C Channel + U Bolt Rubber Sleeve System, Pipe running with wall distance 75mm (In case of fixed to wall)

S&F PVC (SWR) pipes75 MM bore single socketed in any length with rubber ring joints fixing done with pipe supporting clamping system consists of Profile Bracket + Continuous Slotted C Channel + U Bolt Rubber Sleeve System, Pipe running with wall distance 75mm (In case of fixed to wall)

S&F PVC (SWR) pipes 110 MM bore single socketed in any length with rubber ring joints laid in trenches or in floor Completed all as directed.

S&F PVC (SWR) pipes75 MM bore single socketed in any length with rubber ring joints laid in trenches or in floor Completed all as directed.

S&F PVC (SWR) bends 110 mm bore with/without access door any radius complete all as directed.

S&F PVC (SWR) bends 75mm bore with/without access door any radius complete all as directed.

S&F PVC (SWR) single junction 'T' 75 mm bore with access door any radius complete all as directed.

S&F PVC (SWR) single junction 'T' 110 mm bore with access door any radius complete all as directed.

Taking up or down 15mm bore dia, steel tubing & connections incl cleaning for refixing or removal to store.

Taking up or down for 20mm bore steel water tubing galvanised with connection complete all as specicfied.

S&F steel water tubing galvanised 15mm bore, med grade fixed to walls and ceiling fixing done with pipe supporting clamping system consists of Mono Brackets +U Bolt Rubber Sleeve mounted system. Water supply pipe 15mm GI running with wall distance 75mm (In case of wall ) or in floor complete all as specified.

Supplying and laying of 20 mm outer dia CPVC pipes SDR 11 & fittings on walls/ceilings or fixing done with pipe supporting clamping system consists of Mono Brackets +U Bolt Rubber Sleeve mounted system. Water supply pipe 20mm CPVC running with wall distance 75mm ( In case of walls) OR laying in floors complete all as specified and directed

S&F steel water tubing galvanised 20mm bore, medium grade with all fittings fixed to wall and ceiling fixing done with pipe supporting clamping system consists of Mono Brackets +U Bolt Rubber Sleeve mounted system. Water supply pipe 20mm GI running with wall distance 75mm (in case of wall) or in floor complete all as specified.

Supplying and laying of 25 mm outer dia CPVC pipes SDR 11 & fittings on walls/ceilings or lfixing done with pipe supporting clamping system consists of Mono Brackets +U Bolt Rubber Sleeve mounted system. Water supply pipe 25mm CPVC running with wall distance 75mm (IN CASE OF WALL) or Laying in floors complete all as specified and directed

S&F Brass Elbow for special fitting of 20 mm bore CPVC pipe complete all as specified and directed.

S&F Brass Tee for special fitting of 20 mm bore CPVC pipe complete all as specified and directed.

S&F Brass Elbow for special fitting of 25 mm outer bore CPVC pipe complete all as specified and directed.

S&F Brass Tee for special fitting of 25 mm outer bore CPVC pipe complete all as specified and directed.

Dismantling floor hearth or wall tiling incl cement mortar bedding complete all as specified.

M&L glazed ceramic coloured tiles, (350x450)x7mm / (350x250)x7mmthick as in vertical surfaces like dado or skirting over 10mm thick in CM 1:4 set & joined in neat cement slurry and pointed in coloured cement to match complete all as specified.

M&L Non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm , in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match tiles over and including 15mm thick screed bed in CM 1:4 complete all as specified complete.

M&L for coloured non-skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors etc set & jointed in neat cement slurry and pointed in white or coloured cement to match, including 15mm thick screed bed in cement mortar 1:6 complete all specified.

M & L, viritfied ceramic tiles 10mm thick light shade (square or rectangular) area of each tile not .exceeding 0.36 sqm in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade, over and including 15mm thick cement sand screed in CM 1:6 complete.

M&L for Vitrified ceramic tiles (light shade) 10mm thick (square /rectangular) polished, area of each tiles not exceeding 0.36 sqm. in skirting etc set and jointed in neat cement slurry ad pointed in white or coloured cement to the match over and including 10mm thick backing coat in cement mortar 1:4 complete all specified.

M & L, viritfied ceramic tiles 10mm thick dark shade/duble charger/ultra charger shade (square or rectangular) area of each tile exc 0.42sqm but n.exceeding 1.00 sqm in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade, over and including 15mm thick cement sand screed in CM 1:6 complete.

M&L for Vitrified ceramic tiles (light shade) 10mm thick (square /rectangular) polished, area of each tiles exceeding 0.42 but not exc1.00 sqm. in skirting etc set and jointed in neat cement slurry ad pointed in white or coloured cement to the match over and including 10mm thick backing coat in cement mortar 1:4 complete all specified.

Chequered cement concrete tiles with grey cement and pigments 300mm x 300mm x 25mm/200mmX200mmX25mm thick, set in 15mm thick CM of (1:6), jointed and pointed in neat cement slurry in floors/paths complete.

M&L for (300X300X10)mm / (400X400X10)mm non skid coloured exterior tile in floor set & jointed in cement slurry over 15mm thick cement screed 1:6 complete all as specified and directed.

M&L 75mm thick Cement concrete type D- 2,1:4:8 (40mm graded aggregate) as in sub base

M&L for 1:3:6 (20mm aggregater) for coping and side filling and other pcc work , all as specified and directed

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided complete

Demolition of stone slabs and tiles of any description or thickness in floors,walls aprons etc (laid, bedded and pointed in any mortar) complete all as specified and directed.

M&L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing with and including 15mm thick screed bed or bedding in cement mortar 1:6 complete all as specified and directed. (Note : Single piece tiles will be placed on the surface of stair case tread area).

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approvedcolour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand;complete.

Supply only water proofing compound.

S&F in repair vitreous china squatting pan "ORISSA" pattern size 580mmx440mm, white with integral foot rest including PVC/CI 'P' or 'S' trap and WC Connector with leaping ring connection to trap including cement concrete, and to flushing pipe, anti-syphonage pipe, etc. including making good to floor, complete all as specified.

Supply & fixing in repair One piece WC with 10 ltrs capacity interal cistern with floor mounting frame, installation kit, drain pipe connection set, including necessary cutting to wall / floor making good to walls / floor complete all as specified and as directed by Engineer-in-Charge

s&F in repair Vitreous China wash down water closet pan (pedestal pattern), white in colour and including flush pipe and all necessary fitting required, complete all as spd and dir.

s&F in repair Vitreous China wash down water closet pan (semi pedestal pattern),Anglo-indian type, white in colour and including flush pipe and all necessary fitting required, complete all as spd and dir.

S&F PVC connections 15mm size with PTMT nuts of 450 mm long

S&F in repair, PVC L/L cistern 10 lir capacity, valveless, syphonic action type with float, handle incl 32mm dia flush pipe of polyethylene of low or high density or PVC & bracket etc complete including all as specified.

S&F Vitreous china wash basin white flat back size 550 x 400mm size, incl cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe and 15mm pillar tap cast copper alloy with capstan head chromium plated complete fixed in repair.

S&F Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed ® 15mm chromium plated cast copper alloy bib taps fixed in repair.

S&F in repair fancy type chromium plated Angle valves, cast copper alloy with cruitch or butterfly handles screwed down high pressure, screwed both ends for 15mm bore iron pipe or brrass ferrule.

S&F in repair fancy type chromium plated with long shank and cup (concealed type) stop valves, cast copper aloy with cruitch or butterfly handles screwed down high pressure, screwed both ends for 15mm bore iron pipe or brass ferrule.

S&F in repair brass chromium plated shower rose 125mm size fitted to steel pipe or union complete

Dismantling water tanks exceeding 250 and not exceeding 500 litres capacity and removing to store complete. Note:- Disturbed surface should be make good by 20 mm graded stone PCC )

Dismantling water tanks exceeding 500 and not exceeding 1000 litres capacity and removing to store complete. Note:- Disturbed surface should be make good by 20 mm graded stone PCC )

S&F rotational moulded polyethylene water storage tanks (tripple layer White in colourcylindrical vertical with closed top) of 500 litres capacity, hoisted and fixed in position including connecting up pipes i.e. nipple socket / unions etc fixed in repairs complete.

S&F rotational moulded polyethylene water storage tanks (tripple layer White in colourcylindrical vertical with closed top) of 1000 litres capacity, hoisted and fixed in position including connecting up pipes i.e. nipple socket / unions etc fixed in repairs complete.

Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc. of capacity exc 500 ltr but n.exc 1000 ltr. Complete all as specified and directed

Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc. of capacity exc 250 ltr but n.exc 500 ltr. Complete all as specified and directed

S&F Ball valves, high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball , screwed for iron pipe or brass ferrule 20mm bore complete.

S&F Ball valves, high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball , screwed for iron pipe or brass ferrule 20mm bore fixed in repairs complete.

S&F Ball valves, high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball , screwed for iron pipe or brass ferrule 15mm bore fixed in repairs complete.

S&F Grating round 140 mm size of PTMT with hole or without hole fixed in repair complete.

S&F as in repair 15mm bore Pillar taps, cast copper alloy, with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe 15mm bore complete.

S&F in repair Wall Mixer 3-in-1 System with telephonic shower rose with 115 mm Bend Pipe & Aerator complete all as specified and directed by Engr-in-Charge.

S&F 15 mm bore brass CP basin mixer long shank / pop up for mixing hot &cold water screwd down for iron pipe and fixed in repair

S&F gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed for 20mm bore pipe complete

Taking down cement plaster incl racking out joints, hacking for key & scrubbing down with water etc complete all as specified.

M&L, 15mm thick rendering in CM 1:6 to brick/conc wall surfaces trowelled to even & smooth w/o using extra cement.

All as above but in CM 1:4 .Including WPC

M&L, 10mm thick rendering in CM 1:3 to brick/conc ceiling icliding extra dubbing/ floating to making good surface surfaces trowelled to even & smooth w/o using extra cement.

Complete removal of existing treatment on walls and roughening surfaces of old plaster by picking sweeping clean and washing down with water to remove dust etc to receive rough plaster complete all as specified and as directed.

M&L for 10mm thick cement plaster in CM 1:4 as in backing coat for rough plaster complete all as specified and as directed.

M&L for Rough cast plaster with rough mixture consisting of crushed stone or fine gravel agg, size 6 to 12mm mixed with course sand and cement in the ratio of 1:1:1 shall be applied and finished even on external wall complete all as specified and as directed.

M & L two coat of oil bound distemper over a coat of primer on newly plastered surfaces of walls including preparation of surfaces complete all as specified and directed by Engineer - in - Charge .

M & L one coat of oil bound distemper on old plastered surfaces of walls including preparation of surfaces complete all as specified and directed by Engineer - in - Charge .

M & L two coat of cement base paint on new surfaces of walls including preparation of surfaces and one coat of primer completeall as specified and directed by Engineer - in - Charge .

M & L one coat of cement base paint on old surfaces of walls including preparation of surfaces completeall as specified and directed by Engineer - in - Charge .

M&L of three coat of white wash on newly plastered surface as on celing including preparation .

M&L of two coat of white wash on old plastered surface as on celing including preparation .

Taking down chowkhats or frame n exc 1.50 Sqm each with shutters (W/out taking off shutters from the frames)

Taking down chowkhats or frame exc 1.50 Sqm but n exc 4 Sqm each with shutters (W/out taking off shutters from the frames)

S & F for pressed steel frames of size 105 X 60 mm with one or more rebates including necessary fixing lugs, butt hinges, locks strike plate etc(thickness of sheet shall be 1.25mm) and making good the plaster of wall in CM 1:6 complete all as specified and directed

S & F for pressed steel frames of size 125 X 60 mm with one or more rebates including necessary fixing lugs, butt hinges, locks strike plate etc(thickness of sheet shall be 1.25mm) and making good the plaster of wall in CM 1:6 complete all as specified and directed

M&L for PCC 1:3:6 type C-1 (using 20mm Graded Stone Aggregate) as in filling of Chowkhats.

S & F 2nd class HW 35mm thick panelled shutters with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and style as per IS-1003 (Pt-I) kiln seasoned and chemically pressure treated.

S&F flush shutter 30 mm thick, solid core construction, with block board core and both face covered with decorative face veneer with lipping/frame to match plywood face panels.

S&F 2nd class HW 35mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. without sash bars), edges of framing plain,chamfered or rounded. fitted with cut and mitred beads for securing glass,etc.; sizes of me-mbers of shutters as specified in SSR PartI, Section 8, clause 8.24 (a).

S&F made single extruded WPC (Wood Polymer composite)) Solid door/ window/ceosetory windows & other Frames/ chowkhat of size 45 X 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade) calcium carboante and natural fibers (Wood powder/roce hisk/wheat husk) and non toxic additives (maximum toxicity index of 12 of 100 gms)fabricated with miter joints after applying PVC Solvent cement and screwed with full body threaded star headed SS screwes having minimum frame density of 750 Kg/cim screw withdrawal strength of 2200 N (Face) & 1100 N (Edge) minimum compressive strength of 58 N/mm2 modules of elasticty 900 N/mm2 and resistance to spread of flame of class A category with property of being termite / borer proof, water/ moisyure proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasterners of required dia and length complete as per direction of Engineer-in- Charge.

Factory made single extruded WPC (Wood Polymer Composite) Solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (suspensio Grade) calcium carbonate and natural fibers (Wood powder/rice husk/wheat husk) and non toxicity additive (maximum toxicity index of12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Eage) minimum compressive strength 50 N/mm2 modulus of elastcity 850 N/mm2 and reistance to spread of flame of class A category with property of being termite/borer proof, water /moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction ofn Engg-in-charge

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube fixed in opening as per specifications and making good the plaster of wall in CM 1:6..

S&F factory made solid panel shutter (PVC) 30mm thick (Style) consisting of frame made out of MS tube for top and bottom rails MS frame shall be covered with heat molded plain colour PVC `C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement as per specifications.

S & F GI wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed in steel windows and wooden shutters.

S & F in repair GI wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed in steel windows and wooden shutters including necessay arrangements like welding etc complete.

S&F aluminium, anodised, barrel tower bolt of extruded section and fixed, 150 mm size

S&F in repair aluminium, anodised, barrel tower bolt of extruded section and fixed, 150 mm size

S&F aluminium, anodised, barrel tower bolt of extruded section and fixed, 200 mm size

S/F Extruded aluminium alloy handles, fabricated type, anodised 125 mm long

S/F in repair Extruded aluminium alloy handles, fabricated type, anodised 125 mm long for cup boards and PVC doors.

S&F extruded aluminium alloy handles fabricated types, anodised, size 150 mm.

S&F in repair extruded aluminium alloy handles fabricated types, anodised, size 150 mm.

S&F extruded aluminium alloy ,anodised ,sliding door bolt 250 mm in length with hasp, staple (bolt type) and fixing bolts and sliding bolts of extruded sections .

S&F in repair extruded aluminium alloy ,anodised ,sliding door bolt 250 mm in length with hasp, staple (bolt type) and fixing bolts and sliding bolts of extruded sections

S&F extruded aluminium alloy ,anodised ,sliding door bolt 150 mm in length with hasp, staple (bolt type) and fixing bolts and sliding bolts of extruded sections

S & F MS butt hinges medium weight cold rolled mild steel 75mm long.

S & F in repair MS butt hinges medium weight cold rolled mild steel 75mm long in wooden/ steel/ iron frame.

S&F rubber beading to aluminium door / window / aluminium frame and like of best quality complete.

S&F in repair rubber beading to aluminium door / window / aluminium frame and like of best quality complete.

S&F in repair door handle 2 nos for aluminium door / window / aluminium frame and like of best quality complete.

S&F in repair door closer Aluminium (Die cast) body hydraulic regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 Kg complete

S&F in repair Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed

Hacking out old broken glass exc 1.5 sqm (any thicknes, size and description) from wooden / metal frames glazed with putty or fixed with beads complete on any storey of the bldg.

S&F 3 mm thick sheet glass, ordinary quality & glazing with oil putty in square n.exc 0.5 sqm each pane

S&F 3 mm thick figured glass pin head type in square n.exc 0.5 sqm each pane

S&F sheet glass 4 mm thick ordinary quality in squares n exc 0.5 sq m each pane all as specified.

S&F sheet glass 4.8 mm thick ordinary quality in squares n exc 0.5 sq m each pane all as specified.

M&L preparation of new steel surfaces of any description, over 10 cm in width or girth, and applying two coats of synthetic enamel paint .

M & L for preparations of new or previously untreated wooden surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer to wooden surfaces.

S & F in repair mild steel, 4-lever, mortice lock, vertical type, size 100mm all as spd.

S & F mild steel 25 mm dia drapery rod, decorative type, with PVC coating and fixed in repairs complete all as specified and directed.

S & F MS bracket, decorative, superior quality, suitable for 25 mm dia drapery rods, all as specified and directed.

S&F Floor door stopper of aluminium alloy body 150 mm long with rubber shoes .

S&F Floor door stopper of aluminium alloy body 150 mm long with rubber shoes fixed in repair

Repair/adjust Pivote and fixture of old double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed in repair icnluding taking down existing aluminium door and refixe the after carryout necessary repair work

S & F as in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed in repair including taking down existing aluminium door and refixe the after carryout necessary repair work , securing Rubber beading, aluminium cleat/beading

Demolition of brickwork or stone/boulder masonry, built in lime mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles

Brickwork with old size flyash bricks, straight or curved on plan exc 6m mean radius, built in CM (1:4)

M&L taking down Aluminium door of size exc 1.50 sqm but n.exc 2.50 sqm & refixing the same after carryout necessary repair work /securing/adjustments the loose parts and Replaced the damge parts with new including necessary joining cleats,glazing clips, ruber neoprene packing,handles 2 Nos in each door, hinges,anodised aluminum snap beading screws etc. complete all as specified.

M&L taking down Aluminium door of size exc 2.50 sqm but n.exc 3.50 sqm & refixing the same after carryout necessary repair work /securing/adjustments the loose parts and Replaced the damge parts with new including necessary joining cleats,glazing clips, ruber neoprene packing,handles 2 Nos in each door, hinges,anodised aluminum snap beading screws etc. complete all as specified.

S&F Powder coated Anodised aluminium frame for doors, windows ventilators and partition with one or more rebates including joining cleat for fixing etc. complete all as specified.

S&F Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sectionsweighing 0.55 kg/m including necessary joining cleats, glazing clips,rubber packing, anodised aluminiumsnap beading, screws, anodised aluminium fittings such as peg stays150mm long (1 no.). hinges type B-21100mm long (2 no.) suitable handle (1no.) complete all as specified Note : (i) Glass panes, wire cloth & rubber beading shall be measured & paid separately .

S&F Anodised aluminium door shutters/partition ,aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, ruber neoprene packing,handles 2 Nos in each door, hinges,anodised aluminum snap beading screws etc. complete all as specified. Note : (i) Glass panes, wire cloth & rubber beading shall be measured & paid separately

Dismantling of Brick tiles or terracing tiles, single layer on roof and removing as directed

Demolition of Mud in roofs, any thickness,including plastering and leeping (whether full thickness removed or only a part thereof)

M&L for cement concrete 1:2:4 type B1 using 20mm graded crushed stone aggregate in padding ,levelling course and the like finish even and Fair 50mm average thickness or as required at site including preparation of RCC roof surface(old or new) with wire brush , drying and cleaning top remove loose particles, filling the cracks by crack filler complete all as specified and directed.

S&F 40mm thick brick tiles laid on 15mm thick screed of cement mortar(1:6) and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement on PCC padding complete all as specified and directed.

All as per above item No 116.00 but except bricks tiles complete all as specified and directed.

M&L for Providing, cement concrete of 1:3:6 of Type C-1 20mm Graded aggregate in roof kerbs (Coving) , rounded or chamfered on edges, all as spd and dir.

M&L applied a coat of bituminious primer confirming to [email protected] Kg per Sqm ,APP BASED POLYMERIC Memberane not less than 3 mm thick. Weighing not less than 3 Kg/m2, reinforcd with polyster non woven febric(weighing not less than 15 Gm/Sqm) and upperside of memberane thermally insulated with white mineral gravel finish, uniformly embedded during manufacturing process shall be laid dry torch application, side coverlaps shall be 75 mm and end slab shall be 100 mm and all over laps and joints shall also be sealed by torch application including one coat of bituminous aluminium paint all as specified and directed.

M&L for flush pointing to bricks laid flat or brick tiles over roof in cement morter (1:3) inlcuding handing out/ taking out old pointing complete all as specified and directed

S&F as in repair brass Mortice lock,vertical type, 4 lever size 100 mm

S&F as in repair brass Mortice lock,vertical type, 4 lever size 65 mm

S&F hollow PVC wall panelling,super strong quality single side prelaminated with flat or fancy patterned on laminated side, incl PVC 'L'and U section for finishing of corners and ends etc inclusive of fixing with screw or with solvent cement required at site on walls complete as specified and directed.including dismantling old panelling /lining etc

Dismantling Wall and ceiling boards (fibre,pulp, insulation, etc.) or insulation boards/ slabs/ blankets , any thickness, including cover fillets

S&F Anodised aluminium snap grid of size 605mmX605mm frame work for false ceiling all as specified including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I.flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified

Exposed metal frame ceiling with calcium silicate board 6mm thick of siliceous and calcareous material reinforced with cellulose fibre or E-ceiling or similar material Board for fixing in 600mm x 600mm grid (Frame work for ceiling shall be measured and paid separately)

Providing and fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions joint with tap, 2 mm thick putty and over two coat of oil bound dister complete all as specified and directed complete all as specified and directed.

Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including complete all as specified and directed.

Removing all disintregated and loose concrete of any thickness incl plaster if any in RCC Colmn, Chajjas, Slabs, Beams, Lintels etc, removing all loose rust/scale from exposed reinforcement bars by using wire brushes and sand paper incl cleaning of exposed surfaces of reinforcemnet with protective anti corrosive epoxy bonding chemical (Mate Pidilite) and tide reinforcement bars/IRC fabric 50mm x 50mm x 12 gauge if reqd to reinforcement concret boind primer to exposed surfaces and applying cement moter 1: 3:4 with MPC (one part cement 3 part send : 1 part 6mm course aggregate) 2 and average thikness note less than 20mm incl IRC 50mm x50mm)x 12mm gauge or reinforcement bars in the removing debris all as specified and directed by EIC (Note : Upto the hight of 3(Three) storey building incl necessory scafolding to execute the work and IRC 50mmx50mmx12 guage or reinforcement bars shall be paid separatly)

Supply only IRC 50m x 50mm x 12 guage welded mesh all as specified and directed.

Dismantling asbestos cement corrugated or semi corrugated sheets as in roof covering all as specified.

S&F Pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall ,fixed with self tapping screws as specified

M&L Pre painted galvalume alumimnium zinc coating GI based Plain steel sheet 0.50 mm th, sheeting of any colour having tensile strength of 550 mpa as in ridges etc,

Dismantling wrought iron or mild steel work of any description not otherwise provided, for MS railing at passage, stair and rear sitouts complete

M&L for rolled sections as in tubular trusses / rafter / purlin fixed with angle cleats or other connecting plates, other iron work confirming to FE-410 (Gde-E-250) complete for holding galvallume sheeting in passage

Supply and Providing precast cement concrete ( 1:3:6) type C-0 using 12.50mm stone aggregate as in louvres and jallies 25mm thick (measured solid), including all mouldings but excluding frame set in cement mortar (1:6), including dismantling existing jallies/louvers of any description and fixed in any position (Pre cast frame shall be measured separately and paid)

Providing precast cement concrete Type C-1 using 20mm graded stone aggregates and set in CM (1:6) in window or door cills, lintels,bressumers, teps,quoin blocks (for use with masonry),string courses, copings.kneelers, apex stones, pier caps,columns, posts,boundary pillars,bed plates, pintle blocks, ancho-rage blocks, bonders (for stone wallin).corbels, brackets,etc. (of any section indicated), with plain fair faces,including chamfers,weatherings,throat- ing etc. and setting in mortar complete with joints to match

S & F in repair fancy type Stainless steel curtain rod 25mm dia including SS brakcet, knobs, rings stops, rollers etc complete all as specified.

S&F 18 mm thick PVC solid board for making modular kitchen cabinet/ cupboard with partition and door of approved making including all necessary fittings like Hasp and staple, magnet, piano Hinges, knobs, etc complete all as specified and directed.

Dismantling old unserviceable cupbord shutter with frame complete all as specified and directed.

Taking down carefully copper/ Aluminium point wiring ( light, fans, socket, power socket) complete incl taking out existing unserviceable terminal boxes and conduit with swithces/sockets/fan regulators and fittings such as ceiling roses, pendants, tube lights fittings lamp holders, brackets light fittings, rectangular blocks DB MCCB etc and making good disturbed surface of wall/ floor etc to match with the existing the surface etc complete and directed by engr in charge

Taking down carefully copper/aluminium Submain wiring from battan /conduit from DBs,MCBs, etc) and making good to disturbed surfaces of walls, floor etc.

Material and labour for point wiring with 1.5 sqmm (22/.3mm) PVC insulated and unsheathed FRLS single core multistranded copper conductor for one light/fan/bell point in existing PVC rigid non metallic concealed conduit 19/20 mm dia medium duty, ISI marked to be terminated & including pressed modular steel boxes & cover plate of module as required on site.including 1.5 sqmm (22/.3mm) PVC insulated and unsheathed FRLS single core multisrtaned copper earth continuity conductor controlled by one switch and/or one regulator complete including repairing the surfaces in Cm 1:3 and finishing the surface as per exisitng treatment all as specified

All as per item No 163 (here-in-before) but One three pin 5 Amp socket outlet point on indep board controlled by one nos, one way switch on indep board

All as per item No 163 (here-in-before) but One three pin 5 Amp socket outlet point on same board controlled by one nos, one way switch on same board

All as per item No 163 above but point wiring with 2.5 sq mm single core FRLS cables and earth continuity wire with 2.5 Sq mm single core cable for one 3 pin 15 Amps socket out let point controlled by one nos, one way switch on indep bd.

All as per item No 163 above One light point controlled by two 2- w a y switches, with cables 1.5 sq. mm size

All as per item No 163 above but point wiring with 4 sq mm single core FRLS cables and earth continuity wire with 4 Sq mm single core cable for one 3 pin 15 Amps socket FOR AC

Material and labour for point wiring with 1.5 sqmm (22/.3mm) PVC insulated and unsheathed FRLS single core multistranded copper conductor for one light/fan/bell point in and including PVC rigid non metallic new concealed conduit 19/20 mm dia medium duty, ISI marked to be terminated & including pressed modular steel boxes & cover plate of module as required on site.including 1.5 sqmm (22/.3mm) PVC insulated and unsheathed FRLS single core multisrtaned copper earth continuity conductor controlled by one switch and/or one regulator complete including repairing the surfaces in Cm 1:3 and finishing the surface as per exisitng treatment all as specified

All as per item No 169 (here-in-before) but One three pin 5 Amp socket outlet point on indep board controlled by one nos, one way switch on indep board

All as per item No 169 (here-in-before) but One three pin 5 Amp socket outlet point on same board controlled by one nos, one way switch on same board

All as per item No 169 above but point wiring with 2.5 sq mm single core FRLS cables and earth continuity wire with 2.5 Sq mm single core cable for one 3 pin 15 Amps socket out let point controlled by one nos, one way switch on indep bd.

All as per item No 169 above but point wiring with 4 sq mm single core FRLS cables and earth continuity wire with 4 Sq mm single core cable for one 3 pin 15 Amps socket FOR AC

S&F Modular switch 1 way 6A 1 module Single pole, one way, 230 volts all as specified and directed

S&F Modular switch 1 way 16A 1 module all as specified and directed

S&F Modular switch 2 way 6A 1 module Single pole, one way, 230 volts all as specified and directed

S&F Modular socket 6A -2/3 pin combined 2 module type 230 volts AC complete all as specified and directed.

S&F Modular socket 6A/16A -2/3 pin combined 2 module type 230 Volts, AC complete all as specified and directed.

S&F Modular lamp holder, insulated body with back plate including LED Bulb of 9 watt suitable for batten fittings and complete all as specified and directed

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

M&L Buzzer, Ding Dong AC 230 volts, single pole ISI Marked,all as specified & directed

Supply and fixing modular bell push 6A 1 module all as specified and directed.

S&F Modular ceiling rose surface bakelite 65mm x 50mm, 3 terminals with back plate etc complete all as specified and directed

Supply & fixing Modular type (1/2 module as per site requirement) ceiling fan regulator electronic step type suitable for 1200mm/1400mm sweep fan complete all as specified.

S&F LED light fitting 1x20watt 4 feet long including LED tube(PC Housing) with driver complete suitable for fixation on wall/roof with body robust, corrosion resistant, superior finish and without any crack. The fitting should have following technical specification (i) surge protection of minimum 2 KV (ii) power factor should be more than 0.90 (iii) cool white colour, (iv) total hormonic distoration (THD) should not be more than 15% (v) lumen output should not be less than 1700 lumens, (vi) can withstand with input voltage range 140-280V AC, (vii) colour rendering index should not be less than 80, (viii) Corelated colour should be minimum 6000 degree Kelvin (ix) Minimum warranty period of 2 Years.

S&F LED light fitting 1x40watt 4 feet long including LED tube with driver complete suitable for fixation on wall/roof with body robust, corrosion resistant, superior finish and without any crack. The fitting should have following technical specification (i) surge protection of minimum 2 KV (ii) power factor should be more than 0.90 (iii) cool white colour, (iv) total hormonic distoration (THD) should not be more than 15% (v) lumen output should not be less than 1700 lumens, (vi) can withstand with input voltage range 140-280V AC, (vii) colour rendering index should not be less than 80, (viii) Corelated colour should be minimum 6000 degree Kelvin (ix) Minimum warranty period of 2 Years.

S&F Inverter type Rechargeable LED Batten light fitting 20watt 4 feet long includes LED tube complete suitable for fixation on wall/roof with body robust, corrosion resistant, superior finish and without any cracks. Led Batten fitting should be of Elegant design offers high Brightness,Energy Saving,and Upto 4 hrs Back up( when Mains supply is off but switch is on condition), having Powerful lithium battery-2600 mah, battery life -500+ Recharge Cycle,Charging Time-8 hrs to 10 hrs with lumen output should not be less than 100 lumens/Watt ,Corelated colour should be minimum 6000 degree Kelvin, sleek and modern design, emergency light is suitable for use in a variety of indoor, and automatically charges when switch is ON complete all as specified and directed by Engr-in-Charge.

Supply and Fixing in replacement LED light fitting Surface/Roof mounting Round type complete 1x12 W , (Dimension(mm) for round light : Ø180x40) polycarbonate batten including LED Tube, suitable for Dot auditorium complete all as specified and directed.Make-Havells , Bajaj CG Syska or equivalent as approved by accepting officer.Make-Havell's, Bajaj CG,Wipro, Osram,Syska or equivalent as approved by accepting officer.

Supply and Fixing in replacement LED light fitting Surface/Roof mounting square type complete 1x12 W ,(Dimension(ft) for square light : 1x1) polycarbonate batten including LED Tube, complete all as specified and directed.Make-Havells , Bajaj CG Syska or equivalent as approved by accepting officer.Make-Havell's, Bajaj CG,Wipro, Osram,Syska or equivalent as approved by accepting officer.

Supply and Fixing in replacement LED light fittings 36 watt designer sky panel diffuser type Recess Mounting type with mounting arrangement (Recess suitable for, 2x2 Grid, Hanging) CCT 6500K, powder coated CRCA sheet steel with high quality LGP and PMMA diffuser. Separate HPF driver suitable for Armstrong and grid ceilling LED 240 volt along with fixing arrangements all as directed. Make : Halonix cat part no. HLFPR22-11-36-CW-SKY or equivalent make.

S&F decorative wall light Wooden housing fixture white glass diffuser B22 Holder suitable for 9 watt LED bulb complete all as specified and directed.

S&F Sheet metal enclosure distribution board SP&N,8 way, double door powder coated, protection class IP-42 suitable for mounting MCB DBs confirrming to IS-13032, IS-8632,BS5484 with min 200 Amp raiting copper bus bar complete all as specified and directed

S&F Sheet metal enclosure distribution board SP&N,12 way, double door powder coated, protection class IP-42 suitable for mounting MCB DBs confirrming to IS-13032, IS-8632,BS5484 with min 200 Amp raiting copper bus bar complete all as specified and directed

Supply and fixing MCBs SP 6 to 32Amps, 240 volts, 10 KA rupturing capacity, IS-8828 marked, of the under mentioned type and rating and fixing in DBs (DBs Catered separately in this schedule) :-Note : Make of the MCB should be the same as that of DB

Supply and fixing MCBs SPN 32Amps to 63 Amps, 240 volts, 10 KA rupturing capacity, IS-8828 marked, of the under mentioned type and rating and fixing in DBs (DBs Catered separately in this schedule) :-Note : Make of the MCB should be the same as that of DB

S&F i Sheet metal enclosure distribution board VTPN,4 way, double door powder coated, protection class IP-54, isolated neutral bar, mechanical impact strength IK 09 suitable for mounting MCCB as incoming and TPN/MCB's as outgoing in DBs confirrming to IS-13032, IS-8632,BS5484 with min 200 Amp raiting copper bus bar and grouting, fixing on wall with nut bolts wasshers proper with pcc works complete all as specified and directed

Supply and fixing TPN 63 Amps, 415 volts, 10 KA rupturing capacity, IS-8828 marked, of the under mentioned type and rating and fixing in DBs (DBs Catered separately in this schedule) :-Note : Make of the TPN should be the same as that of DB

Supply and fixing MCCBs FP 63 Amps, 415 volts, 16 KA rupturing capacity, IS-8828 marked, of the under mentioned type and rating and fixing in DBs (DBs Catered separately in this schedule) :-Note : Make of the MCCB should be the same as that of DB

Supply and fixing MCCBs FP 100 Amps, 415 volts, 16 KA rupturing capacity, IS-8828 marked, of the under mentioned type and rating and fixing in DBs (DBs Catered separately in this schedule) :-Note : Make of the MCCB should be the same as that of DB

Supply & fixing in replacement of Bldg security light fitting LED 30/35W, pressure die cast housing epoxy powder coating IP -65, connected with and including 0.5 sqmm flexible copper multistranded conductor cable including security light bracket made to shape out of GI pipe 40 mm bore light grade, 1.5 mtr length and fixed with MS Calmps of size 40x5 mm- 02 nos ,nuts, bolts and washers on wall. all as specified and directed.

M & L for submain wiring alongwith earth wire with the 2x6.0 sq. mm +1x6.0 sq. mm earth wire sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed as required(The above mentioned specified runs of single core cables and specified runs of earth continuity conductors and the relevant conduit with accessories shall be measured as one run length).

M & L for submain wiring alongwith earth wire with the 2x10.0 sq. mm +1x10.0 sq. mm earth wire sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed as required(The above mentioned specified runs of single core cables and specified runs of earth continuity conductors and the relevant conduit with accessories shall be measured as one run length).

Supply and fixing Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of capacity 20 AMP

Supply and fixing of post top lantern of LED 25W with symmetrical light distribution , spun alumnium landascape luminaire with high power LEDs as light source ,ip 65 protection with suitable GI tubing including all accessories all as specified and directed. of of Make- , Bajaj CG Syska or equivalent as approved by accepting officer.

Supply & Fixing HYLEM sheet laminated 3 mm thick including cutting required size drilling holes for incorporating switch, socket, regulators etc. complete all as specified and directed.. (a) of size 10x6 inch

Supply & Fixing HYLEM sheet laminated 3 mm thick including cutting required size drilling holes for incorporating switch, socket, regulators etc. complete all as specified and directed.. (b) of size 7x5 inch

Supply & Fixing HYLEM sheet laminated 3 mm thick including cutting required size drilling holes for incorporating switch, socket, regulators etc. complete all as specified and directed.. (c) of size 4x4 inch

supply and fix 5 Amps switch piano type

supply and fix 15 Amps switch piano type

supply and fix 5 Amps socket piano type

supply and fix 15 Amps socket piano type

supply and fix white cover plate for 1 module

supply and fix white cover plate for 2 module

supply and fix white cover plate for 3 module

supply and fix white cover plate for 4 module

supply and fix white cover plate for 6 module

supply and fix white cover plate for 8 module

supply and fixing metal flush box 1/2 module

supply and fixing metal flush box 3 module

supply and fixing metal flush box 4 module

supply and fixing metal flush box 6 module

supply and fixing metal flush box 8 module

S&F PVC 20/25mm casing and caping, ISI marked complete all as specified.

Supply &fixing LED Strip 24 W LED recess/surface light fitting Indoor type suitable for existing light fitting as per sample complete all as specified and directed.

Supply only aluminium lugs suitable for cable of size 10 to 16 sqmm complete all as specified and directed.

Supply only aluminium lugs suitable for cable of size 25 sqmm complete all as specified and directed.

S&F in Replacement of GI Bracket 25 mm light grade dia pipe for Building Light including clamp & nut bolts all as specified and directed.

Supply &fixing LED driver 25/30 W/36W LED recess/surface light fitting Indoor type suitable for existing light fitting as per sample complete all as specified and directed.

Supply &fixing LED SPD 25/30 W/36W LED recess/surface light fitting Indoor type suitable for existing light fitting as per sample complete all as specified and directed.

S&F in replacement PVC air fresh air Fan 200/250 mm sweep, 230 volts, fixed on wall with suitable size nut, bolts and washers and connection complete all as specified & directed. Note; Make a hole as per site requirement rate include in this price

Supply & Fixing Exhaust Fan steel body with louvers and accessories 230 V 300 MM sweep heavy duty with blades & copper winding with service value all as specified and directed by Engr-In-Charge.

M&L for WEE Plus LED bulk head luminaire of capacity 10 Watt an ideal energy efficient solution for upgrading conventional GLS bulkhead luminaires to LED bulk head IP 65 complete all as specified and directed by Engr-InCharge

M&L for Copper strip 20 x 3.15mm with saddles and fixing screws etc. for roof conductors and down conductors above ground including connection with the earthing by means of nuts, bolts and washers complete all as directed.

M&L for Earthing complete with galvanised mild steel earth electrode plate 600 X 600 X 3.15 mm thick buried directly and vertically in ground connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical Plate No 3 of MES SSR Part-I connected to main switch board or main control board all as specified and testing on completion including provision of earth wire protected by galvanised iron 15 mm bore medium grade pipe with all fittings from the earth electrode fixed along pole or wall with and including 25 x 6mm flat iron clamp, bolts, nuts and washers and watering pipe shall be 20 mm bore GI medium grade from top of the earth pit to top of earth plate electrode including all excavation and earth work in any type of soil and removal of soil upto 10 metre, PCC pit with pre-cast RCC cover with handle, charcoal/salt, funnel , CI frame etc complete all as directed. NOTES : (i) The concrete pit shall be made in PCC 1:2:4 type B-O, using 12.00 mm graded crushed stone aggregate 40mm thick precast cover slab of RCC (1:2:4), type B-1, using 20mm graded crushed stone aggregate with suitable MS handle in lieu of CI cover (ii) Item includes the cost of 7.5 metre GI pipe for protection of earth wire. Any variation in length shall be adjusted through deviation order (iii) Items includes cost of 7.5 metre earth lead wire. Any variation in length shall be adjusted through deviation order. (iv) Earth electrode shall be surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides.

M&L for Earthing complete with copper earth plate of size 60 cm x 60cm x 3.15 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to copper strip of size 20x3mm by means of tinned brass bolt/snuts/washers, protected by 40mm bore GI medium grade pipe from earth plate & upto 3m long pole fixed with 2 clamp made from mild steel flat iron 32x6mm bolts, nuts, washer etc. earth plate shall be surrounded by alternate layer of charcoal or coke and common salt 15cm thick all around buttom and top of earth plate 20mm dia GI Medium grade pipe for watering and including funnel, wire mesh, RCC cover & frame PCC 1:3:6 type C1 using 20mm graded stone aggregate as in earthing pit including necessary excavation & earth work all as specified & shown on electrical plate No. 3 of SSR Part-I, (Note: (i) PCC chamber shall be constructed at least 1.5 mtr away from the earth electrode and pipe for watering shall be provided in slanting manner.

Please Enable Macros to View BoQ information