REPAIR MAINT OF STREET SECURITY LIGHT AND PERIODICAL SERVICE REPAIR OF DG SETS CRANES AND CERTAIN ALLIED WORKS AT DIAT DU AND MILIT GIRINAGAR PUNE 25

Amount

Repair / maintenance of street / security lights any type, flood lights or any other external lights in its position fixed on pole /building/structure/high mast pole by taking down to ground, if required, testing all the compenents / parts, wiring etc, identifying and replacing the defective components like electronic driver,surge protection device (SPD) connection wires/ cable, MCB etc including refixing the fitting to its original position (if taken down), including repair / maint of street light control timer & junction box complete all as specified and directed. Note: (i) The rate against the above mentioned item is deemed for cost of labour and allied expenses only. (ii) Cost of spares electronic driver,surge protection device (SPD), connection wire, MCB, timer contactor spares etc) replaced against above mentioned item will be measured & paid for separately. (iii) Any type of T&P/Vehicle mounted hydraulic ladder for the work should be arranged by contractor. (iv) The contractor shall maintain proper record of repair / maint in a register duly bringing out the details of spares replaced on each and every street light and get it authenticated from concerned JE E/M on daily basis. The contractor shall put up the maint record register to Engineer-in-charge for inspection every Monday or as and when asked for. (v) The contractor shall maintain sufficient stock of spares / material required for repair / maint of street lights with the concerned JE E/M against the supply only items.

S&F in repair electronic driver suitable for any type LED light fittings complete all as specified and directed.

Material and labour for scrapping / removing of rust on the panel boards preparation of surfaces for fresh painting, cleaning inside the panel boards with the vacuum or blower and painting by means of spray paint with two coats of synthetic enamel paint of approved colour complete all as specified and directed.

M & L to find out fault in LT line bring/call fault finding machine equipment and find out fault in any size of LT UG Cable including disconnecting of cable connection from both side panels/poles and necessary excavation in any type of strata to reach upto cable and making space for cable joint complete all as specified and directed. Note:- (i) Cable required at site same size of faulty cable if required for jointing purpose will be paid in relevant item. (ii) Jointing material will be paid in relevant Item.

M&L for rerouting of LT UG cable of any size including earthwork, excavation, returning & Filling and making good the disturb surfaces complete all as specified and directed.

S&F in repair of GI pipe bracket of up to 32/40 mm dia 1.2mtr long bend to shape for street light fitting made out of 32 mm dia GI light grade pipe fixed on pole using new FI clamp including necessary new nut, bolt and washer complete all as specified and directed.

S&F in repair surge protection device(SPD) of capacity 10KV compatible with industrail & outdooor LED fixtures complete all as specified and directed.

S&F in repair/replacement LED 60 Watt Street light fittings made up of pressure die cast housing with toughened glass and direct modular IP lens, IP 66 protection , potted driver and with system efficacy of 125lm/W including making all electrical connection from light fitting to pole junction box/ O/H line for making the light functional including taking down old u/s complete all as specified and as directed.

All as per item herein above but capacity of LED 30/45 Watt Street light fittings complete all as specified and directed.

All as per item herein above but capacity of LED 90 Watt Street light fittings complete all as specified and directed.

S & F in repair/replacement LED 100 watts flood light fittings white/warm white in colour, aluminium or higher grade powder coated and water proof pressure die cast aluminium enclosure, with inbuilt electronic drivers and IP 66 protection complete, Single phase, etc fixing in MS chanel by drilling hole of suitable, size, using nut, bolts and washers of suitable size including suitable mounting structure on existing pole/any type of structure as reqd at the site including taking down old u/s complete all as specified and directed.

All as per item herein above but of capacity 150 Watt LED Flood light fittings complete all as specified and directed.

All as per item herein above but of capacity 250 Watt LED Flood light fittings complete all as specified and directed.

Supply and fixing LED Rope/strip Light Indian Tricolor Strip Light - Orange + White + Green Colour / Republic Day Rope/strip Light IP68 including any no of adaptor, end cap, middle connector, clamp ,plug waterproof etc rate included with quoted rate complete all as specified and directed.

Supply and fixing of LED Focus light fixture 24 watt of white/warm white/multi coloured bobust design(IP 66) die cast aluminium housing with tempered glass for precise light distribution for illumination for piller or as required at sitecomplete all as specified and directed. Note:- Necessary T & P/ladder required at site for fixing of light up to 18 mtr height included in quoted rate.

Taking down existing Avaition light from Building / hight mast light/ and any other location upto 35 mtrs height and supply and fixing LED Integral avaition light comprising of aluminium housing with polycarbonate enclouser, 240V AC, 50Hz including all electrical connection as required at site complete all as specified and directed.

S&F in replacement of Heritage E 27 holder without lamp post top/gate light (Pipe dia 78 mm,dia 230 mm x 360 height) ideal fitting to be fixed in existing RCC pole with suitable fittings as per site requirement complete all as specified and directed.

Supply and Fix in replacement integral 40 Watt LED post top lantern black/ copper dust painted cast aluminium spigot, spun aluminium canopy with clear acrylic cover and accessories complete with 50 mm OD black powder coated MS pipe not less than .3mtr length with suitable 5 mm thick ms base plate with provn of 04 Nos anchoring bolts complete all as specified and directed.

S&F in replacement 50 watt flood light outdoor type,IP-68 , energy saving , elegantly designed cast aluminium housing and heat sink for thermal management, high efficiency long life LED module aesthetically designed diffuser and reflector to deliver uniform light output complete all as specified and directed.

Supply and Fixing in replacement 10 watt W/WW LED bollard Integral decorative LED bollard with polycarbonate diffuser and IP 65 protection incl demolition of existing PCC and make suitable PCC for new bollard as per site requirement and fixing arrangements complete all as specified and directed.

S & F MCB SP 240 volts C curve 6-32 amps complete all as specified and directed.

S & F MCB SPN 240 volts C curve 6-32 amps complete all as specified and directed.

S & F MCB SPN 240 volts C curve 40 amps complete all as specified and directed.

S & F MCB TPN 415 volts C curve 16-32 amps complete all as specified and directed.

S & F MCB TPN 415 volts C curve 40-100 amps complete all as specified and directed.

S & F Digital timer switch, DIN type daily / weekly with 25 ON/OFF programmes , 16 amps 250 volts AC complete all as specified and directed.

S & F Power contactor 16/18 amps 3 pole complete all as specified and directed.

S & F Power contactor 40 amps 3 pole complete all as specified and directed.

S & F PVC sheathed copper cable 3 core 1.5 Sqmm grade complete all as specified and directed.

S& F in replacement of MCCB 63 Amps 4 pole 415 V. Thermal magnetic adjustable type & should be Ics=Icu=100% with both side spreader links complete all as specified and directed.

All as per item herein above but of capacity MCCB 100 Amps 4 pole 415 V 25 KA complete all as specified and directed.

All as per item herein above but of capacity MCCB 125 Amps 4 pole 415 V 25 KA complete all as specified and directed.

All as per item herein above but of capacity MCCB 160 Amps 4 pole 415 V 25 KA complete all as specified and directed.

All as per item herein above but of capacity MCCB 250 Amps 4 pole 415 V 36 KA complete all as specified and directed.

All as per item herein above but of capacity MCCB 400 Amps 4 pole 415 V 50 KA complete all as specified and directed.

All as per item herein above but of capacity MCCB 800 Amps 4 pole 415 V 50 KA complete all as specified and directed.

Restreaching tightening and fixing in position, the existing OH ACSR conductor LT Line 3 phase with neutral and earth wire 440 V 5/6 wire by loosing and taking down existing binding wire from the insulator of any size of ACSR conductor and bring it to required sag incl new binding wire and tightening of cross arm on each pole and required trimming of tree branches Note: 1. Span length (any Nos of wire of conductor shallbe measured in running meter unit combined. 2. Unit are quoted by the contractor shall be deemed to incl for cutting and trimming branches of the trees coming in contact with ACSR conductor and separators complete all as specified and directed.

Supply & Laying, jointing & testing of UG LT cables 35 sqmm 4 core XLPE insulated, PVC sheathed aluminium conductor multi stranded armoured heavy duty 1100 Volt grade laid in trenches/ ducts/ along poles/through pipe under road etc with new aluminium lugs of cable size complete all as specified and directed.

All as per item herein above but size 25 sqmm 4 core complete all as specified and directed.

All as per item herein above but size16 sqmm 4 core complete all as specified and directed.

All as per item herein above but size10 sqmm 4 core complete all as specified and directed.

All as per item herein above but size 6 sqmm 3 core complete all as specified and directed.

All as per item herein above but size 4 sqmm 3 core complete all as specified and directed.

Taking out existing defective worn out UG LT cable of any size 1100 volts grade from trenches of any size from different locations complete all as specified and directed. Note: Excavation & earth wk shall be measured and paid for separately

Excavation in trenches in hard/dense soil n.exc 1.5 M wide and not exceeding 1.5 mts in depth in wide for laying of cables and n exc 1.5 mtr in depth and getting out incl dressing/trimming sides and levelling/grading and ramming of bottom of excavation complete all as specified and directed.

Excavation in trenches in soft/loose soil n exc 1.5m wide and n.exc 1.5m in depth and getting out complete all as specified and directed.

Returning, filiing in incl spreading, leveling watering and well ramming excavated soil in layers not exceeding 25 cm thick each, filling back in trenches after cables have been laid and tested complete all as specified and directed.

Removing excavated surplus soil obtained from excavation to a distance not exceeding 1.5 m above the starting point, complete all as specified and directed.

Supply & Laying double wall corrugated pipe 50 mm bore (DWC) of HDPE ISI Mark for enclosing cable below ground / road surface, to a required depth, including suitable size coplers for jointing of pipe complete all as specified and directed.

All as per item herein above but size 40 mm bore complete all as specified and directed.

S& F GI tubing 80 mm bore light grade ISI marked with all fittings laid in trenches for protection of LT cables or on fixed pole by flat iron clamps, nut, bolt, washers suitable size complete all as specified and directed.

All as per item herein above but size 50 mm bore complete all as specified and directed.

All as per item herein above but size40 mm bore complete all as specified and directed.

Supply and fix in replacement of cable Junction box thermo plast (weather proof) IP 66, on street light poles made out of thermoplastic of size 300mm x 200 mm x 105 mm size with connector for connecting incomming and outgoing of cable including 01 No of MCB DP 10 Amps to control the pole light circuit and MS brackets made out of 32 x 4 mm flats for fixing the box on post complete with nuts, bolts and washers and suitable size of double compression cable glands for incomming, outgoing of cable complete all as specified and directed.

All as per item herein above but of of size 140mm x 140 mm x 95 mm complete all as specified and directed.

S&F distribution box 2 Module 230V, 5 HZ, IP-65 & IK-09 Class-II, weather proof cabinets, door and cabinet fully reversible, removable chassis and faceplates, including weatherproof glands, rails qty-1 Nos, coppper fork type 100 A busbars as short link including end caps, qty-1 nos, MCB SPN 10 Amp 230V, 50 HZ, complete all as specified and directed.

S&F in replacement MCB DB 02 way SPN (single door) sheet metal enclosure factory made suitable for MCB DB's 240 volts with 200 amp rated busbar, neutral & earthing link bar, surface mounting complete including MCB SPN 20 Amp 230V, 50 HZ, complete all as specified and directed

Labour for trimming / pruning tree branches overhanging or interfering or obstructing electrical pole or street lights complete all as directed in such a way that the clearance between Street light pole and tree branches should not be less than 3 mtrs around the Pole/Fitting complete all as specified and directed. Note : one span of 25-30 mtrs will be considered as one Job

Material and labour for bituminus road/hard standing cutting by using suitable hydraulic road cutter for a width not exceeding 300 mm and depth 600 mm for laying of GI pipe incl refilling and making good with Tarmac/ PCC/RCC duly matching with the existing surface Note:1. GI pipe will be measured & paid separately. 2. Quoted rate shall deemed to incl the cost of making good the disturbed surface.

M&L for straight through joint (epoxy) for PVC insulated and sheathed aluminium conductor under ground cable incl freud, thimbles, nut & bolts, washers etc and testing afterjointing complete, complete all as specified and directed. (a) 10 sqmm to 35 sqmm 3.5 core

Supply & fix GI tubing light grade 40 mm dia ISI marked 1 mtr long with Flat Iron Base for mounting of Flood light with all fittings incl nut,bolt,washers suitable size complete all as specified and directed.

M&L for scrapping down and removing of old deteriorated paint from steel tubular poles LT (up to 11 Mtr) height above ground level , preparing surface for painting , applying two coats of aluminium paint upto full height of pole including MS clamps, GI bracket, fitting ets all as directed at site including making balck and white strips of 30 cms each upto 1.5 m above PCC muffs with black and white paint and marking of pole no up to 2 m above PCC muff, letter should not be longer than 6 cm height with 16 cm dia circle around the marked no complete all as such specified and directed by Engr-in Charge.

M&L for scrapping down and removing of old deteriorated paint from Post top lantern poles (RCC/GI) /(2 to 3 mtr) height above ground level , preparing surface for painting, applying two coats of black paint upto full height of pole including MS clamps, GI bracket, fitting ets all as directed at site complete all as specified and directed.

Supply, transport, errecting and fixing steel tubular swaged welded pole of over all height 8.5 m long complete type 410-SP-22 conforming to IS-2713 (Part I to III 1998 with cast iron base plate, finial tapper plug cap, bolt, nut and washer etc., complete all as specified and directed. Note: (i) rates included for Excavation, earth work and PCC work for embedding pole shall not be measured and paid seperately. (ii) Pole upto 1.5 m top of coping shall be painted with 2 coats of black and white strips alternate 30cm each over one coat of red oxide primer. (iii) Steel tubular pole above 1.5 m shall be painted with 2 coats of aluminium paint over a coat of red oxide primer. (iv) Pole below ground shall be tarred by one coat. (v) Poles shall be numbered and the rate for above items shall be deemed to be inclusive in the quoted rate.

S&F in replacement of digital timer switch distribution board, factory assembled in powder coated sheet steel enclosure, comprising of 40 Amps 3 Pole MCB, power contactor and 230V digital time switch for controlling LED/SV etc street lights, including earth work for fixing Timer switch distribution Board and shall be provided 4 Nos 35x35x4mm thick angle iron supports of not less than each 0.6 mt height duly painted with anti corrosive black paint and grouted in PCC 1:3:6 at suitable depth as per site requirement complete all as specified and directed.

S&F automatical timer switch distribution board, factory assembled in powder coated sheet steel enclosure, comprising of 40 Amps 3 Pole MCB power contactor and 230V digital time switch for controlling LED/SV etc street lights, including earth work for fixing Timer switch distribution Board and shall be provided 4 Nos 35 mm x 35 mm x 4 mm thick angle iron supports of not less than each 0.6 m height duly painted with anti corrosive black paint and grouted in PCC 1:3:6 at suitable depth as per site requirement complete all as specified and directed.

Disconnecting/taking down the hexagonal/Hectagonal GI Pole which is titling/leaning by engaging suitable crane or manullay and refixing the same with suitable nut and bolt on existing foundation complete all as specified and directed.

M&L for PVC insulated flat twin core 2.5 Sqmm solid aluminium conductor cable including PVC conduit pipes of dia not less than 20 mm for connection of security light from junction box or existing source to light fitting to be drawn through conduit/pipe along the pole or through inside the street light pole or over head line/existing source to street light fittings etc , including taking out old u/s wires complete all as specified and directed.

S & F in replacement Busbar panel weather proof outdoor type single door, fabricated out of 3.15 mm thick CRCA sheet with epoxy powder coating of RAL-7035 (Siemens Gray) shade with matt finish with seven tank pre treatment process. The Panel shall be compartmentized design totally enclosed, dust and vermin proof, conforming to degree of protection IP-55, Gaskets between all adjacent units and beneath all covers shall be provided to render the joints dust proof. All doors and covers shall be provided with cylindrical panel locks and shall be fully gasketed with neoprene rubber and shall be lockable. The panel shall be provided with aluminium bus bars, 300mmX40mmX5mm(thickness) electrolytic grade of adequate rating. The bus bars and Interconnecting links shall be insulated with heat shrinkable PVC sleeve with 4. RYB & black colour coding and fix horizontally. The bus bars shall be supported on unbreakable, non-hygroscopic SMC insulated supports at sufficiently close intervals to prevent busbars sag and shall be housed in a dedicated compartment. including incoming and outgoing cable connection, glands, thimbles All joints and connection shall be done with galvanised or codmium plated high tensile nuts, bolts and washers. The panel shall be provided with 04 Nos 25mm x 25mm x 3mm thick angle iron supports of not less than each 3 mtr height duly painted with anti corrosive black paint and grouted on wall (at Sudan Dome)and suitable fixing arranement as per site requirement. The overall size of the Busbar panel shall be 350mm x 200mm x 400mm (LxBxH) including PCC 1:3:6 complete all as specified and directed.

M & L for making hole on a street light pole top and bottom for entry of service wire of 1.5 sqmm disconnecting the existing service connection from junction box and fitting and same has been reconnecting to junction box and fitting complete all as specified and directed.

M & L for fixing of line separator suitable for LT line three/four conductor feeder complete all as specified and directed.

Disconnecting and taking out old existing worn out cable lugs, nuts, bolts, washers etc from LT panel board of 4 wire system (incomming and outgoing) and supply and connect with new aluminium lugs all sizes as per site requirement and nuts, bolts, washers etc complete all as specified and directed.

Surface excavation not exceding 30 cm deep in hard dense soil and averaging 15 cm deep and getting out green vegetation, roots, bushes, etc surrounding of 2 / 4 pole structure / substations complete all as specified and directed.

Repair and refixing of u/s voltmeter/Ammeter of different capacity complete all as specified and directed.

S&F in replacament of LED type phase indicator to be fitted on panel ( R,Y, B as per site requirement) complete all as specified and directed.

M&L for earthing with galvanised steel earth plate electrode 600 x 600 x 6mm thick buried directly in ground earth pit not less than 2.25M deep below ground level with top edge of the plate not less than 1.5M below normal ground level connected to galvanised strip 32 x 6mm by means of nuts, bolts, checknuts, washers of galvanised iron or steel all as shown in electrical plate No. 3 of SSR Part I connected to earthing test point including excavation/ earth work in any strata removal of surplus earth, GI pipe for watering and funnel, PCC 1:3:6 type C1 chamber with RCC 1:2:4 type B1 in cover slab with 40mm dia light grade GI protection pipe and 20mm dia light grade GI pipe for watering complete all as specified and directed.

M&L for earthing with galvanised steel earth plate electrode 600 x 600 x 6mm thick buried directly in ground earth pit not less than 2.25M deep below ground level with top edge of the plate not less than 1.5M below normal ground level connected to GI Earth wire 4 mm by means of nuts, bolts, checknuts, washers of galvanised iron or steel all as shown in electrical plate No. 3 of SSR Part I connected to earthing test point including excavation/ earth work in any strata removal of surplus earth, GI pipe for watering and funnel, PCC 1:3:6 type C1 chamber with RCC 1:2:4 type B1 in cover slab with 40mm dia light grade GI protection pipe and 20mm dia light grade GI pipe for watering all as specified and directed by Engr-in-charge.

M & L for replacement of unserviceable MS clamp with new clamp as per sample/as per site requirement made out of MS flat iron 25 x 5mm including fixing nuts bolts, washers etc and painting with two coats of synthetic enamel paint over a coat of red oxide primer complete all as directed

Dismantling and taking down existing any type unserviceable parts of High mast light suitable for 6 to 9 lantern symmetrically fitted along with complete overhauling their control gear/motor etc having two point suspension system with stainless steel wire rope of 6 mm dia 97/19 gauge and double drum winch with luminaire mounting arm, pully assembly, aviation obstruction light lightning arrester spike including greasing of motor / pulley parts complete all as specified and directed. Note : Spares shall be measured and paid separately as supply under relevant item here in below

Supply only in repair Rope SWR 6mm complete all as specified and directed.

Supply only in repair Gear motor complete all as specified and directed.

Supply only in repair 5 core cable complete all as specified and directed.

Supply and fix in repair of aluminium lugs of size 6 sqmm to 16 sqmm complete all as specified and directed.

Supply and fix in repair of aluminium lugs of size 25 sqmm to 50 sqmm complete all as specified and directed.

Supply and fix in repair of aluminium lugs of size 70 sqmm to 120 sqmm complete all as specified and directed.

Comprehensive/Preventive maintenance of 500 KVA DG sets consisting of normal repairs such as tightening of nut bolts, greasing, checking/replacing of battery terminals, leveling of distilled water, cleaning of fuel tank, alternator where ever exists with vacuum cleaner including replacements of unservicable defective/ worn out spares such as diesel filters, oil filters, rubber hose pipe, V-belt, fuel pipe and change of oils, cleaning of radiator etc complete all as specified and directed. Note: (i) Maintenance of DG set to be carried out as per manufacturers instructions or as requirement by qualified service engineer. (ii) Materials/ Spare parts/Lub oil required for above maintenance shall be measured and paid seperately under repective items as "Supply only Materials". (iii) Cost of labour employed for the maintenance purpose, T&P used and other petty items such as cotton waste, Kerosene oil, Grease, nuts, bolts, cost for fixing spares shall be deemed to be included in quoted rate. (iv) All spares and oil replaced will be measured and paid under relevant items of schedule. (v) Fixing charges for the spares and oil etc. are deemed to be included in quoted rate for comprehensive/preventive maintenance of DG sets , if the spares are not included in Sch 'A' then department will provide the same Free for fixing.

All as per item herein above but of capacity 380 KVA DG Set complete all as specified and directed.

All as per item herein above but of capacity 300 KVA DG Set complete all as specified and directed.

All as per item herein above but of capacity 250 KVA DG Set complete all as specified and directed.

All as per item herein above but of capacity 160 KVA DG Set complete all as specified and directed.

All as per item herein above but of capacity 60/62.5 KVA DG Set complete all as specified and directed.

All as per item herein above but of capacity 30/40 KVA DG Set complete all as specified and directed.

Supply only in repair/replacement of Diesel filter with 'O' ring suitable for 500 KVA DG set complete all as specified and directed.

Supply only in repair/replacement of Diesel filter with 'O' ring suitable for 380 KVA DG Set complete all as specified and directed.

Supply only in repair/replacement of Diesel filter with 'O' ring suitable for 300 KVA DG Set complete all as specified and directed.

Supply only in repair/replacement of Diesel filter with 'O' ring suitable for 250 KVA DG Set complete all as specified and directed.

Supply only in repair/replacement of Diesel filter with 'O' ring suitable for 160 KVA DG Set complete all as specified and directed.

Supply only in repair/replacement of Diesel filter with 'O' ring suitable for 60/62.5 KVA DG Set complete all as specified and directed.

Supply only in repair/replacement of Diesel filter with 'O' ring suitable for 30/40 KVA DG Set complete all as specified and directed.

Supply only in repair/replacement of Oil filter element with 'O’ring suitable for 500 KVA DG set complete all as specified and directed.

Supply only in repair/replacement of Oil filter element with 'O’ring suitable for 380 KVA DG Set complete all as specified and directed.

Supply only in repair/replacement of Oil filter element with 'O’ring suitable for 300 KVA DG Set complete all as specified and directed.

Supply only in repair/replacement of Oil filter element with 'O’ring suitable for 250 KVA DG Set complete all as specified and directed.

Supply only in repair/replacement of Oil filter element with 'O’ring suitable for160 KVA DG Set complete all as specified and directed.

Supply only in repair/replacement of Oil filter element with 'O’ring suitable for 60/62.5 KVA DG Set complete all as specified and directed.

Supply only in repair/replacement of Oil filter element with 'O’ring suitable for 30/40 KVA DG Set complete all as specified and directed.

Supply only in repair/replacement of Air filter element suitable for 500 KVA DG set complete all as specified and directed.

Supply only in repair/replacement of Air filter element suitable for 380 KVA DG Set complete all as specified and directed.

Supply only in repair/replacement of Air filter element suitable for 300 KVA DG Set complete all as specified and directed.

Supply only in repair/replacement of Air filter element suitable for 250 KVA DG Set complete all as specified and directed.

Supply only in repair/replacement of Air filter element suitable for 160 KVA DG Set complete all as specified and directed.

Supply only in repair/replacement of Air filter element suitable for 60/62.5 KVA DG Set complete all as specified and directed.

Supply only in repair/replacement of Air filter element suitable for 30/40 KVA DG Set complete all as specified and directed.

Supply only in repair/replacement of fan belt sets suitable for 500 KVA DG set complete all as specified and directed.

Supply only in repair/replacement of fan belt sets suitable for 380 KVA DG Set complete all as specified and directed.

Supply only in repair/replacement of fan belt sets suitable for 300 KVA DG Set complete all as specified and directed.

Supply only in repair/replacement of fan belt sets suitable for 250 KVA DG Set complete all as specified and directed.

Supply only in repair/replacement of fan belt sets suitable for 160 KVA DG Set complete all as specified and directed.

Supply only in repair/replacement of fan belt sets suitable for 60/62.5 KVA DG Set complete all as specified and directed.

Supply only in repair/replacement of fan belt sets suitable for30/40 KVA DG Set complete all as specified and directed.

Supply only in repair/replacement of Rubber hose set for water and air circuit complete suitable for 500 KVA DG Set complete all as specified and directed.

Supply only in repair/replacement of Rubber hose set for water and air circuit complete suitable for 380 KVA DG Set complete all as specified and directed.

Supply only in repair/replacement of Rubber hose set for water and air circuit complete suitable for 300 KVA DG Set complete all as specified and directed.

Supply only in repair/replacement of Rubber hose set for water and air circuit complete suitable for 250 KVA DG Set complete all as specified and directed.

Supply only in repair/replacement of Rubber hose set for water and air circuit complete suitable for 160 KVA DG Set complete all as specified and directed.

Supply only in repair/replacement of Rubber hose set for water and air circuit complete suitable for 60/62.5 KVA DG Set complete all as specified and directed.

Supply only in repair/replacement of Rubber hose set for water and air circuit complete suitable for 30/40 KVA DG Set complete all as specified and directed.

Takingout and repair / Maintenance of Water Pump Including replacement of complete assembly as Gasket, Bearing, pipe, rubber seal & clamp etc for 500 KVA DG Set complete all as specified and directed.

Takingout and repair / Maintenance of Water Pump Including replacement of complete assembly as Gasket, Bearing, pipe, rubber seal & clamp etc for 380 KVA DG Setcomplete all as specified and directed.

Takingout and repair / Maintenance of Water Pump Including replacement of complete assembly as Gasket, Bearing, pipe, rubber seal & clamp etc for 300 KVA DG Set complete all as specified and directed.

Takingout and repair / Maintenance of Water Pump Including replacement of complete assembly as Gasket, Bearing, pipe, rubber seal & clamp etc for 250 KVA DG Set complete all as specified and directed.

Takingout and repair / Maintenance of Water Pump Including replacement of complete assembly as Gasket, Bearing, pipe, rubber seal & clamp etc for 160 KVA DG Set complete all as specified and directed.

Takingout and repair / Maintenance of Water Pump Including replacement of complete assembly as Gasket, Bearing, pipe, rubber seal & clamp etc for 60/62.5 KVA DG Set complete all as specified and directed.

Takingout and repair / Maintenance of Water Pump Including replacement of complete assembly as Gasket, Bearing, pipe, rubber seal & clamp etc for 30/40 KVA DG Set complete all as specified and directed.

Supply & fix in replacement of water pump for 500 KVA DG set complete all as specified and directed.

Supply & fix in replacement of water pump for 380 KVA DG set complete all as specified and directed.

Supply & fix in replacement of water pump for 300 KVA DG set complete all as specified and directed.

Supply & fix in replacement of water pump for 250 KVA DG set complete all as specified and directed.

Supply & fix in replacement of water pump for 160 KVA DG set complete all as specified and directed.

Supply & fix in replacement of water pump for 60/62.5 KVA DG set complete all as specified and directed.

Supply & fix in replacement of water pump for 30/40 KVA DG set complete all as specified and directed.

Takingout burnt/unservieable self starter and refixing after necessary repair including replacement of carbon brushes, brush holder, bearings, solenoid coil, replacement of burnt armature, rewinding of coils, replacement of pinion gears etc for 500 KVA DG sets complete all as specified and directed.

All as per item herein above but 380 KVA DG Set complete all as specified and directed.

All as per item herein above but 300 KVA DG Set complete all as specified and directed.

All as per item herein above but 250 KVA DG Set complete all as specified and directed.

All as per item herein above but 160 KVA DG Set complete all as specified and directed.

All as per item herein above but 60/62.5 KVA DG Set complete all as specified and directed.

All as per item herein above but 30/40 KVA DG Set complete all as specified and directed.

Supply & fix in replacement of self starter for 500 KVA DG set complete all as specified and directed.

Supply & fix in replacement of self starter for 300 KVA DG set complete all as specified and directed.

Supply & fix in replacement of self starter for 250 KVA DG set complete all as specified and directed.

Supply & fix in replacement of self starter for 160 KVA DG set complete all as specified and directed.

Supply & fix in replacement of self starter for 60/62.50 KVA DG set complete all as specified and directed.

Takingout burnt/unservieable Dynamo and refixing after necessary repair including replacement Main coil, axuilary coil and carbon brush etc for 500 KVA DG sets complete all as specified and directed.

All as per item herein above but 380 KVA DG Set complete all as specified and directed.

All as per item herein above but 300 KVA DG Set complete all as specified and directed.

All as per item herein above but 250 KVA DG Set complete all as specified and directed.

All as per item herein above but 160 KVA DG Set complete all as specified and directed.

All as per item herein above but 60/62.5 KVA DG Set complete all as specified and directed.

All as per item herein above but 30/40 KVA DG Set complete all as specified and directed.

Labour for cleaning (twice during contract period in each DG set) of 500 KVA DG set fuel tank of under mentioned capacity by draining out residual oil and removal of sludge from bottom of the tank complete all as specified and directed.

All as per item herein above but 380 KVA DG Set complete all as specified and directed.

All as per item herein above but 300 KVA DG Set complete all as specified and directed.

All as per item herein above but 250 KVA DG Set complete all as specified and directed.

All as per item herein above but 160 KVA DG Set complete all as specified and directed.

All as per item herein above but 60/62.5 KVA DG Set complete all as specified and directed.

All as per item herein above but 30/40 KVA DG Set complete all as specified and directed.

Supply and fix in repair/replacement of automatic voltage regulator device for 500 KVA DG set complete all as specified and directed.

All as per item herein above but 380 KVA DG Set complete all as specified and directed.

All as per item herein above but 300 KVA DG Set complete all as specified and directed.

All as per item herein above but 250 KVA DG Set complete all as specified and directed.

All as per item herein above but 160 KVA DG Set complete all as specified and directed.

All as per item herein above but 60/62.5 KVA DG Set complete all as specified and directed.

All as per item herein above but 30/40 KVA DG Set complete all as specified and directed.

Material & labour for dismantling the radiator from 500 KVA DG set after removing hose pipe connection, nut, bolts etc and taking out the same to civil workshop for repair and descaling of radiator using descaling chemical, remove mud/deposit on fins and tubes including brazing where required to stop leaking tubes / joints of tubes, replacement of cover etc complete all as specified and directed.

All as per item herein above but 380 KVA DG Set complete all as specified and directed.

All as per item herein above but 300 KVA DG Set complete all as specified and directed.

All as per item herein above but 250 KVA DG Set complete all as specified and directed.

All as per item herein above but 160 KVA DG Set complete all as specified and directed.

All as per item herein above but 60/62.5 KVA DG Set complete all as specified and directed.

All as per item herein above but 30/40 KVA DG Set complete all as specified and directed.

Supply & fix in replacement of power contactor AC , 50Hz , 4 Pole, 415 V AC suitable for 500 KVA DG set AMF/ control panel complete all as specified and directed.

All as per item herein above but 380 KVA DG Set complete all as specified and directed.

All as per item herein above but 300 KVA DG Set complete all as specified and directed.

All as per item herein above but 250 KVA DG Set complete all as specified and directed.

All as per item herein above but 160 KVA DG Set complete all as specified and directed.

All as per item herein above but 60/62.5 KVA DG Set complete all as specified and directed.

All as per item No. 186 above but 30/40 KVA DG Set complete all as specified and directed.

M &L for removing the fuel injection pump (FIP) from 500 KVA DG set and carry out servicing and calibration from authorised maker's work shop including replacement of injectors, nozzles, etc. and refitting the same for smooth and efficient functioning complete all as specified and directed.

All as per item herein above but 380 KVA DG Set complete all as specified and directed.

All as per item herein above but 300 KVA DG Set complete all as specified and directed.

All as per item herein above but 250 KVA DG Set complete all as specified and directed.

All as per item herein above but 160 KVA DG Set complete all as specified and directed.

All as per item herein above but 60/62.5 KVA DG Set complete all as specified and directed.

All as per item herein above but 30/40 KVA DG Set complete all as specified and directed.

Taking down the existing perished/damaged asbestos rope and supply and replace with new asbestos rope 10 mm thick on the exhaust pipe including covering with aluminium foil complete all as specified and directed.

Supply battery leads, PVC insulated multi-stranded, copper conductor, 1.25 m long duly fixed with brass clamps, copper lugs suitable for 40 to 500 KVA DG sets acomplete all as specified and directed.

M&L for replacement of brass battery terminal suitable for lead acid battery 12 V/24V any AH complete all as specified and directed.

Supply and filling of Lub Oil of specific grade (20W40 or Eqv) to carrying out maintenance of various capacity of DG sets complete all as specified and directed.

Supply and filling of electrolyte of suitable Sp gravity for lead acid batteries to carrying out maintenance of DG sets batteries complete all as specified and directed.

Supply and filling of coolent to carrying out maintenance of various capacity of DG sets complete all as specified and directed.

Supply and filling of distilled water to carrying out maintenance of various capacity of DG sets complete all as specified and directed.

Supply and fix in repair fuel pipe steel braided, steel stranded with benzo bolts and washers etc complete of length 30 cm long complete all as specified and directed.

Supply and fix in repair fuel pipe steel braided, steel stranded with benzo bolts and washers etc complete of length 45 cm long complete all as specified and directed.

Supply and fix in repair fuel pipe steel braided, steel stranded with benzo bolts and washers etc complete of length 60 cm long ccomplete all as specified and directed.

Supply and fix in repair fuel level indicator transparent PVC pipe of suitable dia for fuel level in tank complete all as specified and directed.

Supply petroleum jelly in 1 Kg plastic sealed container complete all as specified and directed.

Labour only for attending breakdowns of DG sets/ control panels through skilled technician or reputed service centre technician of DG sets with necessary tool kits, checking minor fault in Engine and alternator , carryout necessary repairs works to rectify the defects without major overhauling/ opening of Engine or Alternators, replace of external spare to repair/rectify the defects and testing DG set for its smooth functioning on full load complete all as specified and directed. Note : 1. Necessary spares required to rectify the defects shall be measured and paid separately as supply only under relavant items. 2. The complaint shall be attended and rectifed within 24 hours from time of reporting by Engr-in-Charge or his authorised representative. 3. Any Major defects shall be reported on priority to Engr-in-Charge to avoid undue delay in fuctioning of installation.

S&F in repair Turbo charger including replacement of worn out parts such as shaft, seal, bush bearing etc complete all as specified and directed.

Taking down the defective flexible coupling at exhaust manifold end fix new flexible coupling stainless steel complete all as specified and directed.

M&L for replacement of exhaust manifold with gasket, and all other connected parts DG set engine complete all as specified and directed.

Supply and fixing in repair/replacement digital ammeter 0 to 500 Amps complete all as specified and directed.

Supply and fixing in repair/replacement digital voltmeter 0 to 500 complete all as specified and directed.

Comprehensive maintenance (consisting of normal repairs)/ preventive maint and attending day to day breakdown of electrically operated travelling (EOT) cranes of 02 Ton capacity comprising of hoist motor, long travel motor, gear box control panel and connected accessories, including replacement of the unserviceable spare parts with new at site complete all as specified and directed. Note :- (i) Maintenece of crane required to be done in every month, which includes cleaning, greasing, oiling whenever required, cheking of all electrical connection in addition standard maintenance as recommended by manufacturer as quarterly, half yearly and yearly, The rate quoted by the contractor including cost of grease, cotton waste, lugs, nuts, bolts and washers, insulation tape, screws small piece of cable and T&P etc. (ii) Quoted unit rate deemed to be include to attend the breakdown any No. of times as and when required by users if any spares are changed shall be measured and paid under relevant item as supply only, fixing charges for the spares are deemed to be included in the quoted rate for comprehensive maintenance of crane. (iii) Load testing of each crane at 100 % of its capacity shall be carried out once during the currency of contract. It will be measured and paid seprately under respective item of schedule.

All as item herein above but EOT Crane 5 Ton capacity complete all as specified and directed.

All as item herein above but EOT Crane 10 Ton capacity complete all as specified and directed.

M&L for checking of Load Carrying Capacity and serviceability of each crane and hoist in the presence of Engr-in-charge and test certificate to be produced in duplicate.The capacities of crane / hoist are as under:- EOT Cranes 2 ,5 ,10 Ton Capacity

M & L for repairs to gear box including replacement of worn out driving/ driven gears, bearings, gear keys, gasket oil seals of capacity 2 ton to 5 ton complete all as specified and directed.

M & L for repairs to gear box including replacement of worn out driving/ driven gears, bearings, gear keys, gasket oil seals of capacity 10 ton complete all as specified and directed.

Supply only HRC fuse contacts complete with base from 5 to 16 amps capacity complete all as specified and directed.

Supply only HRC fuse contacts complete with base from 20 A to 40 amps capacity complete all as specified and directed.

Supply only pendant push button complete all as specified and directed.

Supply only Current Collector complete all as specified and directed.

Supply only AC Electromagnetic Brakes complete all as specified and directed.

Supply only DC Electromagnetic Brakes complete all as specified and directed.

Supply only Festoon Cable Trolley complete all as specified and directed.

Supply only Brake Linings complete all as specified and directed.

Supply only Electro Hydraulic Thrustor Brake complete all as specified and directed.

Supply only Brake Drum & Coupling complete all as specified and directed.

Supply only Rectifiers complete all as specified and directed.

Supply only Electromagnetic Clutches complete all as specified and directed.

Supply only Couplings complete all as specified and directed.

Supply only Electromagnetic Brake Coils complete all as specified and directed.

Supply only fuse contacts complete with base form 70 A to 110 A capacity including of old fuses complete all as specified and directed.

Supply only brake shoe assemble complete (Thruster type ) with lining set suitable for main hoist of 5 ton cab for vertical drive complete all as specified and directed.

M & L for replacement / topping up hydraullic / gear DOX EP 230 oil capacity of crane complete all as specified and directed.

Supply & Fix gasket for gear box up to 5 Ton capacity of crane complete all as specified and directed.

Supply & fix gasket for gear box for 5 to 10 Ton capacity of crane complete all as specified and directed.

Supply & fix pendant push buttonall complete all as specified and directed.

Supply & Fix 150 mm length porcelain busbar insulator cylindrical type of desired lenth complete all as specified and directed.

Supply & Fix 200 mm length porcelain busbar insulator cylindrical type of desired lenth complete all as specified and directed.

Supply electromagnetic brake coil 300 KVA capaicty complete all as specified and directed.

Supply time delay electro pneumatic with 2 No + 2 NC, PN type 220 volts complete all as specified and directed.

M & L for rewinding of splingring motor 1 to 2 HP 415 volt, 3 phase with same cage superenamelled copper wire incl taking down & reinstalling complete all as specified and directed.

M & L for rewinding of splingring motor 5 HP 415 volt, 3 phase with same cage superenamelled copper wire incl taking down & reinstalling complete all as specified and directed.

M & L for rewinding of splingring motor 7.5 HP 415 volt, 3 phase with same cage superenamelled copper wire incl taking down & reinstalling complete all as specified and directed.

Supply and fix high quality digital flex board showing installation details and and diagram with wood frame of size 4'x3'fixed in wall or outside of installation complete all as specified and directed.

Supply and fix high quality digital flex board showing installation details and and diagram with wood frame of size 5'x4' fixed in wall or outside of installation complete all as specified and directed.

Supply and fix high quality flex board showing installation details and and diagram with wood frame of size 4'x4' fixed in wall or outside of installation complete all as specified and directed.

supply & Fixing Battery 180 AH 12V DC replacement of old unserviceable Battery at 100 t0 500 KVA DG set connected all accessories, Battery terminal, battery Led, etc complete all as specified and directed.

supply & Fixing Battery 90 AH 12V DC replacement of old unserviceable Battery at 62.5 t0 165 KVA DG set connected all accessories, Battery terminal, battery Led, etc complete all as specified and directed.

M&L for repairing of AMF panel of DG set including taking down burnt circuit wiring and replacing with new wiring, changing of power contactor, modification of the panel's busbar with suitable rating of bus bar with nuts and bolts, colour coding sleaves for bus bar complete all as specified and directed. Note : Power Contactor item will be presured & paid seperately under relevant item of schedule.

Supply and fixing of ATS unit for AMF panel of any capacity complete all as specified and directed.

Supply and fixing of 24 V, 30 A Battery charger for charging Lead Acid battery input range 170V to 270 V operating range, naturally cooled, for charging the battery complete all as specified and directed.

PURVA ELECTRICALS AND ENGINEERS (BID ID -3418099)

R K ENTERPRISES (BID ID -3421895)

shakti engineering and electrical works (BID ID -3423204)

SKS Electricals (BID ID -3424222)

Bidder Name

M/S Divyani Aadhar Patil