Development of master road ...

Amount

Wet Mix Macadam. Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density.as per technical clause 406 of MORTandH specifications

Providing and laying 30mm - 45 mm bituminous concrete with 100-120 TPH batch type hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder VG - 40 @ 5.4% per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction complete as per technical clause 507 of per MORTH specifications.....

Providing and laying 80mm -100 mm dense graded bituminous macadam with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder VG 40 @ 4.0% by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction complete, as per technical clause No. 505 of MORTandH specifications...

Providing and laying 50mm - 75 mm dense graded bituminous macadam with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder VG 40 @ 4.5% by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction complete, as per technical clause No. 505 of MORTandH specifications.

Providing and applying tack coat with penetration grade bitumen VG - 10 using bitumen pressure distributor at the rate of 0.30 kg per sqm on the prepared bituminous/ granular surface cleaned with mechanical broom as per technical clause 503 of MORTandH specifications...

Providing and applying primer coat with bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.85 kg/sqm using mechanical means as per technical clause 503 of MORTandH specifications...

Construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with Rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401.of MORTandH specifications..

Providing and Laying Reinforced cement concrete pipe NP4/prestressed concrete pipe for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1 :2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets 1600 mm dia.

Providing and Supplying, and installation of Plate Earthing material with copper strips 25 X 5 mm including plate at bottom with salt, coal, ammonium chloride, with 8 inch to 1.5 inch PVC pipe and pit cover on top. Complete job 15 ft to 20 ft deep with satisfaction of Engineer-in charge.

Supply, Installation, Testing and Commissioning of LED Street Light with a minimum system lumen of 35000 lm and system wattage not exceeding 250W with a nominal system efficacy of 140 lumen/watt. The LED used shall have CCT of 5700K, SDCM = 5 and CRI=70. The housing should be made of LM6/ADC12 Alloy, non-corrosive Single Piece pressure die-cast aluminum, to withstand extreme environments. The spigot shall be part of “Single Piece Pressure Die-cast housing” and shall not be bolted to the luminaire housing to ensure robust design. The name of the brand should be embossed/engraved and should not be mentioned using sticker/screen printing. It should have corrosion resistant powder coating to pass NSS of 500 Hrs. The luminaire LED shall have declared Lifetime of 75K hours@L70. Product should be designed for continuous operation (10-12 Hrs. per day). The Ingress protection should be minimum IP66 and impact resistance shall be IK10. The minimum luminaire dimensions shall be L: 630mm, W: 255MM, H: 135MM (with control gear compartment) and nominal weight shall be 3.8KG (±10%) and minimum windforce area of 0.121sq.m. Control gear compartments shall be Top maintainable without accessing/opening the optical compartment. The Luminaire should have a minimum 10 KV/5KA SPD duly bolted in the Luminaire. The SPD should be able to sustain a minimum 15 hits of 5KA rating i.e. Total of 45 hits across all the three modes as per IEEE 62.41.2. The luminaire should be of Class B Serviceability. The LED used in the luminaire shall be SMD type only and shall be from either Signify, Philips, Osram, Nichia, APT Electronics and CREE make or equivalent. The Driver should be asphalt potted and should be a BIS approved driver. The driver should be 1-10V dimmable future proof driver. The driver shall have operating voltage of 120V to 270V, PF=0.95 @full load, THD=10% @ full load. The driver should be capable of withstand voltage stress of 440V for 8 Hrs., should have an auto shutdown @ 325V(±15V) and have an auto recovery feature. The driver shall comply to IEC61547, IEC 61000-3-2 and CISPR15. The luminaire shall have SPD bolted in-side the luminaire. The luminaire driver and it’s SPD shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79, Type test as per IS10322, `FAT` before dispatch as per IS 10322 and IK Test. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of luminaire. The LED Luminaire and it`s driver both should be BIS registered. Successful bidder shall submit the following reports before supply of material for approvals: LM79 issued by NABL accredited lab, LM80 issued by LED manufacturer, Type Test Certificate for luminaire as issued by NABL accredited lab, IK test report issued by NABL accredited lab, RoHS compliance issued by LED luminaire manufacturer, BIS certificate for LED Luminaire and Driver.

Supply, Installation, Testing and Commissioning of LED Street Light with a minimum system lumen of 5400 lm and system wattage not exceeding 45W with a nominal system efficacy of 120 lumen/watt. The LED used shall have CCT of 5700K, SDCM = 5 and CRI=70. The housing should be made of non-corrosive Single Piece pressure die-cast aluminum, to withstand extreme environments. The luminaire LED shall have declared Lifetime of 50K hours@L70. Product should be designed for continuous operation (10-12 Hrs. per day), The Ingress protection should be minimum IP66 and impact resistance shall be IK07. The minimum luminaire dimensions shall be L: 274mm, W: 84MM, H: 76MM (with control gear compartment). The luminaire shall have nominal weight of 0.85KG (±10%) and minimum wind force area of 0.023sq.m.. Control gear compartments shall be Top maintainable without accessing/opening the optical compartment. The Luminaire should have a minimum 10 KV/5KA SPD duly bolted in the Luminaire. The luminaire should be of Class B Serviceability. The LED used in the luminaire shall be SMD type only and shall be from either Signify, Philips, Osram, Nichia, APT Electronics and CREE make or equivalent. The Driver should be asphalt potted and should be a BIS approved driver. The driver shall have operating voltage of 140V to 270V, PF=0.95 @full load, THD=10% @ full load. The driver should be capable of withstand voltage stress of 440V for 8 Hrs, 320V for 48 Hrs. The driver should Auto Shutdown at = 320V (±15V) and Auto Recovery at 300 - 315V and Should Auto Shutdown at = 90V and Auto Recovery at = 100V ±5V. The driver should be potted. The driver shall comply to IEC61547 and IEC 61000-3-2. The luminaire shall have SPD in-side the luminaire. The luminaire driver and it’s SPD shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79, Type test as per IS10322, `FAT` before dispatch as per IS 10322 and IK Test. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of luminaire. The LED Luminaire and it`s driver both should be BIS registered. Successful bidder shall submit the following reports before supply of material for approvals: LM79 issued by NABL accredited lab, LM80 issued by LED manufacturer, Type Test Certificate for luminaire as issued by NABL accredited lab, IK test report issued by NABL accredited lab, RoHS compliance issued by LED luminaire manufacturer, BIS certificate for LED Luminaire and Driver.

Supply, Installation, Testing and Commissioning of LED Street Light with a minimum system lumen of 12600 lm and system wattage not exceeding 90W with a nominal system efficacy of 140 lumen/watt. The LED used shall have CCT of 5700K, SDCM = 5 and CRI=70. The housing should be made of LM6/ADC12 Alloy, non-corrosive Single Piece pressure die-cast aluminum, to withstand extreme environments. The spigot shall be part of “Single Piece Pressure Die-cast housing” and shall not be bolted to the luminaire housing to ensure robust design. The name of the brand should be embossed/engraved and should not be mentioned using sticker/screen printing. It should have corrosion resistant powder coating to pass NSS of 500 Hrs. The luminaire LED shall have declared Lifetime of 75K hours@L70. Product should be designed for continuous operation (10-12 Hrs. per day). The Ingress protection should be minimum IP66 and impact resistance shall be IK10. The minimum luminaire dimensions shall be L: 435mm, W: 200MM, H: 135MM (with control gear compartment) and nominal weight shall be 1.8KG (±10%) and minimum windforce area of 0.062sq.m. . Control gear compartments shall be Top maintainable without accessing/opening the optical compartment. The Luminaire should have a minimum 10 KV/5KA SPD duly bolted in the Luminaire. The SPD should be able to sustain a minimum 15 hits of 5KA rating i.e. Total of 45 hits across all the three modes as per IEEE 62.41.2. The luminaire should be of Class B Serviceability. The LED used in the luminaire shall be SMD type only and shall be from either Signify, Philips, Osram, Nichia, APT Electronics and CREE make or equivalent. The Driver should be asphalt potted and should be a BIS approved driver. The driver should be 1-10V dimmable future proof driver. The driver shall have operating voltage of 120V to 270V, PF=0.95 @full load, THD=10% @ full load. The driver should be capable of withstand voltage stress of 440V for 8 Hrs., should have an auto shutdown @ 325V(±15V) and have an auto recovery feature. The driver shall comply to IEC61547, IEC 61000-3-2 and CISPR15. The luminaire shall have SPD bolted in-side the luminaire. The luminaire driver and it’s SPD shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79, Type test as per IS10322, `FAT` before dispatch as per IS 10322 and IK Test. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of luminaire. The LED Luminaire and it`s driver both should be BIS registered. Successful bidder shall submit the following reports before supply of material for approvals: LM79 issued by NABL accredited lab, LM80 issued by LED manufacturer, Type Test Certificate for luminaire as issued by NABL accredited lab, IK test report issued by NABL accredited lab, RoHS compliance issued by LED luminaire manufacturer, BIS certificate for LED Luminaire and Driver.

Supply, Installation, testing and commissioning of high-quality LED Flood Light with a minimum system lumen of 36000 lm and system wattage not exceeding 300W with a nominal system efficacy of 120 lumen/watt. The LED used shall have CCT of 5700K, SDCM = 5 and CRI=70. The housing should be made of non-corrosive h-pressure die-cast aluminum, to withstand extreme environments. The luminaire shall have declared Lifetime of 50K hours@L70. Product should be suitable for continuous operation (10-12 Hrs. per day). The Ingress protection should be minimum IP66 and impact resistance shall be IK07. The front cover shall be toughned glass. The minimum luminaire dimensions shall be L: 380mm, W: 192MM, H: 77MM (with fins). The luminaire shall have nominal weight of 4KG (±10%). The Luminaire should have a 10 KV/5 KA SPD duly bolted in the Luminaire. The SPD should be able to sustain a minimum 15 hits of 5KA rating i.e. Total of 45 hits across all the three modes as per IEEE 62.41.2. The luminaire should be of Class B Serviceability. The LED used in the luminaire shall be SMD type only and shall be from either Lumileds, Osram, Nichia, APT Electronics/ CREE make or equivalent. The luminaire shall have multiple beam angles option to meet different road widths for the same stretch to ensure same look of the housing. The driver shall have operating voltage of 120V to 270V, PF=0.95, THD=10% @ full load. The driver should Auto Shutdown at = 320V and Auto Recovery at 300 - 315V and Should Auto Shutdown at = 90V and Auto Recovery at = 100V ±5V. The luminaire driver and it’s SPD shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79, Type test as per IS10322, `FAT` before dispatch as per IS 10322 and IK Test. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of luminaire. The LED Luminaire and it`s driver both should be BIS registered. Successful bidder shall submit the following reports before supply of material for approvals: LM79 issued by NABL accredited lab, LM80 issued by LED manufacturer, Type Test Certificate for luminaire as issued by NABL accredited lab, IK test report issued by NABL accredited lab, RoHS compliance issued by LED luminaire manufacturer, BIS certificate for LED Luminaire and Driver.

Providing and fixing of thimble 16mm aluminium including making connections punching thimbles, complete with the satisfaction of Engineer in charge.

Constructing brick masonry manhole in cement mortar 1: 4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1 :1.5:3 mix (1 cement : 1.5 coarse sand (zone-Ill) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (Zone-Ill) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1 :2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 120x90 cm and 2.5 m deep including C.I. cover with frame (heavy duty) 560 mm internal diameter, total weight of cover and frame to be not less than 208 kg (weight of cover 108 kg and weight of frame 100 kg). with common burnt clay non modular bricks of class designation 7.5 Complete in all respect as per satisfaction of Engineer-in-charge

Constructing brick masonry manhole in cement mortar 1: 4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1 :1.5:3 mix (1 cement : 1.5 coarse sand (zone-Ill) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (Zone-Ill) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1 :2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 120x90 cm and 1.450 m deep including C.I. cover with frame (heavy duty) 560 mm internal diameter, total weight of cover and frame to be not less than 208 kg (weight of cover 108 kg and weight of frame 100 kg) With common burnt clay non-modular bricks of class designation 7 .5 Complete in all respect as per satisfaction of Engineer-in-charge

Providing and laying of ASTM UPVC PIPE SCH-40 2` to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work.

Providing and laying of Service Saddle 63/50mm x 40 mm Size Make- to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work

Providing and laying of Air Release Valve 1` Dia Size, to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work

Providing and laying of Screen Semi Automatic Filter 2.5 ` 30m3/hr to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work.

Providing and laying of 2` Dia. Solenoid globe Valves with fabric reinforced diaphragm and rugged PVC durable glass -filled nylon construction, compatible with and slow closing to prevent water hammer, pressure rating upto 10.4 KSC to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work.

Providing and laying of Automation Controller 4 Station, to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work.

Providing and laying of Powder Coated ENCLOSER BOX FOR AUTOMATION CONTROLLER to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work.

Providing and laying of Voltage Stabilizer to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work.

Providing and laying of Powder Coated Filter Support Unit to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work.

Providing and laying of Pressure Relief Valve size 2` dia to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work.

Providing and laying of sprinklers to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work. for horticulture

Providing and laying of MTAandFTA to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work.

Providing and laying 2.5 sq mm single core wire to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work.

Providing and laying of ASTM UPVC Pipe Fittings like T, Band, Socket and valve to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work.

Providing and laying of 40 Mm PVC Ball Valve to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work.

Credit of kerbstone (70% of total length) (the amount computed by the rates quoted against recovery itmes will not be included in the total amount rather it will be deducted while calculating financial statement of the agency, kerbstones obtained from dismantling of existing median, islands has been calculated taking assumption that 70% of existing kerbstone will be retreived and can be reused. The reserve rates are minimum rates to be used as base for quoting purchase rate by he agency. No rates below reserve price will be considered for all purpose, in case the agency quotes lesser than reserve price, the price quited against the recovery of existing kerbstones shall have minimum reserve price of Rs. 1988/- per cum).

Bidder Name

Amount

R K JAIN INFRA PROJECTS PRIVATE LIMITED (GSTN-06AAGCR1240N1ZC) BID ID -1100524

Satya Parkash and Bros Pvt Ltd (GSTN-06AAHCS1210Q1ZA) BID ID -1103169

Sarvodya Infracon Ptd. Ltd. (GSTN-09AAYCS3350E1ZZ) BID ID -1104942

KALUWALA CONSTRUCTION PRIVATE LIMITED (GSTN-06AAHCK0172D1ZY) BID ID -1105436

M/s Mahashiv Promoters Pvt. Ltd.(GSTN-NA)--1097382

Jeet Construction Company(GSTN-NA)--1105497

MAHAVIR PRASAD GUPTA AND SONS(GSTN-NA)--1104221

Sarvodya Infracon Ptd. Ltd.

M/s Mahashiv Promoters Pvt. Ltd.

Satya Parkash and Bros Pvt Ltd

R K JAIN INFRA PROJECTS PRIVATE LIMITED

KALUWALA CONSTRUCTION PRIVATE LIMITED

MAHAVIR PRASAD GUPTA AND SONS

Jeet Construction Company

M/s Mahashiv Promoters Pvt. Ltd.

R K JAIN INFRA PROJECTS PRIVATE LIMITED

Satya Parkash and Bros Pvt Ltd

KALUWALA CONSTRUCTION PRIVATE LIMITED

MAHAVIR PRASAD GUPTA AND SONS

Bidder Name

Jeet Construction Company