SPECIAL REPAIR TO TOILET BLOCKS, PROVN OF SENTRY POST AND REV WORKS IN CERTAIN UNITS AT MIL STN JAISALMER

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premise complete all as specified and directed by Engineer-in-charge.

M&L for Glazed ceramic coloured tiles 350 x250x 7mm/ 450x 350x 7mm thick in vertical surfaces etc set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10mm thick screed in CM 1:4 complete all as specified and directed by Engineer-in-charge.

Demolition of cement concrete (unreinforced) concrete of any description and in any position not otherwise specifically provided for sunken floor and depositing the same at a distance not exceeding 250m away from the outer edge of bldg complete all as specified and directed by Engineer-in-charge.

M&L for 25mm thk PCC (1:2:4) type B-0 (using 12.5mm graded stone aggregate) as in subbase of floors & finishing the surface even & smooth without using extra cement complete all as specified and directed by Engineer-in-charge.

M&L non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid over and including 15mm thick screed bed in cement mortar (1:6) complete all as specified and directed by Engineer-in-charge.

Taking down cement plaster of any description on stone or brick walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engineer-in-charge.

M&L for rendering 15 mm thick readymade plaster on inner/outer walls with approved makes by adding 17-19% of potable water by weight of material. For thickness above 15 mm it is recommended to be applied in multiple layers. Ready-mix plaster shall complies with IS 1661-1972, IS 2250-1965, IS 2402-1963 and confirms the Compressive strength @ 28 Days- 10-12 Mpa/ Bulk density- 1500-1600 Kg/m3 complete all as specified and directed by Engineer-in-charge. Note :The rate quoted by contractor shall include cleaning of surface, application as per instruction and scaffolding upto 20mtr height all as specified and directed.

M&L for rendering 5 mm thick readymade plaster on inner/outer walls with approved makes by adding 17-19% of potable water by weight of material. Ready-mix plaster shall complies with IS 1661-1972, IS 2250-1965, IS 2402-1963 and confirms the Compressive strength @ 28 Days- 10-12 Mpa/ Bulk density- 1500-1600 Kg/m3 complete all as specified and directed by Engineer-in-charge. Note :The rate quoted by contractor shall include cleaning of surface, application as per instruction and scaffolding upto 20mtr height all as specified and directed)

M&L for MS props erecting for temporary supports to the structural members like beams, slabs etc. to relieve the load on the members during breaking of damaged concrete, removal guniting, excavation or any dismantling work as per the instruction of engineer in-charge. These supports shall be provided either in the form of props or trestles fabricated using structural steel as per the site requirements complete all as specified and directed by Engineer-in-charge.

M&L for Chipping of slab/ columns/ beams/ chajjas/ parapet/ roof projection/ balcony/ staircase and removing loose mortar with chisel hammer without much impact on concrete surface, clean the surface by sand blasting the surface using river sand with minimum of 6 kg pressure at the nozzle or air blow by electric pressure blower by mechanical compressor, cleaning the exposed reinforcement with wire brushes etc and disposal of debris for all lead and lifts, complete all as specified and directed by Engineer-in-charge.

M&L for cleaning & applying rust remover of approved makes in two coats over rusted reinforcement surface and providing anti corrosive coating with two component epoxy based zinc rich primer/Rust passivation Inhibitor coat at the rate of 6-8 sq. mtr/ltr not less than 50 microns dft with equivalent material of approved makes to reinforcement surface as per manufacturer’s instructions including all scaffolding , machinery, tools tackles and clearing of debris. complete all as specified and directed by Engineer-in-charge.

M&L for providing leak proof shuttering in any position cut to length and providing including runners supports as per manufacturer’s instructions and including all necessary scaffolding, machinery, tools tackles and men materials.complete all as specified and directed by Engineer-in-charge.

M&L for applying to the damaged concrete portion of slab/ columns/ beams/ chajjas/ parapet / roof projection/balcony/ staircase with single component, fiber reinforced, dual shrinkage- compensated thixotropic, cementitious ptch repair mortar of approved makes (having the technical parameters mentioned in material specifications) capable of applying up to 20-25mm thick in double layer initially by hand and finishing with troweled carefully compacting the same around the rebar and finishing to bring it in line with existing concrete surface with an average specified thickness complete all as specified and directed by Engineer-in-charge.

BONDING COAT: Providing, mixing and applying bonding coat of approved adhesive on chipped portion of RCC roof as per specifications and direction of Engineer-In-charge complete in all respect. SBR Polymer (@10% of cement weight) modified cementitious bond coat @ 2.2 kg cement per sqm of surface area mixed with specified proportion of approved polymer complete all as specified and directed by Engineer-in-charge.

Tender Application Note :- (i) From serial No. 7, 8, 13, 14 and 15 for the structural rapair and strengthening and rehabilitation and roof treatment shall be applied by the company’s authorized applicator firm only. (ii) Contractor have to get prior approval of applicator or authorized agency by submitting its authorization letter to this office for approval prior to commencement of work. Department will conduct an official varification from manufacturer of its authorised agency. (iii) Submission of 10 year warranty certificate for structural repair and roof waterproofing treatment work over roof is mandatory after completion of work. (iv) The cost of Scaffolding work required at certain places is including in the respective items catered for repairs itself. No extra shall be paid for the same.

Material and labour for preparation of newly plastered surfaces of walls and applying two coats of white wash on walls over a coat of alkali resistant primer complete all as specified and directed by Engineer-in-charge.

M&L three coat of white wash on new surface of ceiling including preparation of surfaces complete all as specified and directed by Engineer-in-charge.

Taking down chowkhat or frames exe 1.5 sqm but exc 4 sqm each with shutter (without taking off shutter from the frames) complete all as specified & directed by Engineer-in-charge.

Taking down shutters of any description area exceeding 2.00 Sqm each complete all as specified & directed by Engineer-in-charge.

S&F solid PVC door frame of size 50x47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S. Square tube suppling and fixing in opening as per specification and drawing complete all as specified and directed by Engineer-in-charge

S&F 30mm thick of factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, uppling & fixing in the frame at site as per specification & drawing etc complete all as specified and directed by Engineer-in-charge

S&F 35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed by Engineer-in-charge

M&L for preparing new or previously untreated wood and wood based surfaces of any description otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint (Ordinary tint) over a coat of pink primer complete all as specified & directed by Engineer-in-charge.

S&F 150mm long aluminium anodized, barrel tower bolt of extruded section complete all as specified and directed by Engineer-in-charge

S&F in repair aluminum handles cast type, anodised, 150mm size complete all as specified and directed by Engineer-in-charge

S&F, 100mm size, butt hinges, medium weight, cold rolled mild steel including necessary welding if required complete all as specified and directed by Engineer-in-charge

S&F 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed by Engineer-in-charge

S & F aluminium anodized tower bolt 200mm size complete all as specified and directed by Engineer-in-charge

S&F, 3mm thick, sheet glass ordinary quality and glazing with oil putty in squares not exceeding 0.50 sqm in each panes and including hacking out old broken glass of any thickness size, quality or description from metal frames complete all as specified & directed by Engineer-in-charge.

M&L for preparation of new or previously untreated steel surface of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red- oxide, zinc chrome primer complete all as specified & directed by Engineer-in-charge.

S&F in repair 15mm dia bib taps cast copper alloy chromium plated with crown or capstan head, screwed down, high pressure screwed for iron pipe complete all as specified & directed by Engineer-in-charge.

S&F in repair 15mm dia pillar taps cast copper alloy with capstan head chromium plated screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts screwed for iron pipe complete all as specified & directed by Engineer-in-charge.

S&F in repair 15mm dia stop valves fancy type cast copper alloy chromium plated screwed down high pressure with crown or capstan head screwed both ends for iron pipe complete all as specified & directed by Engineer-in-charge.

S&F in repair 10 ltrs capacity PVC low level flushing cistern with inlet, ball valve, float, handle including fitting and fixtures and taking down the old damaged cisterns and providing connections to WC and flush pipe without any damage to the existing fittings complete all as specified & directed by Engineer-in-charge.

S&F in repair 600 mm long PVC connection pipe of 15mm bore with PTMT nut at both ends complete all as specified & directed by Engineer-in-charge.

S&F in repair CP grating (with & without hole) for Nahani trap and floor trap of size 100 mm dia fixed complete all as specified & directed by Engineer-in-charge.

S&F in repair brass chromium plated shower rose with swivel joints 125mm dia with 18mm dia chromium plated pipecomplete all as specified & directed by Engineer-in-charge.

S&F in repair, vitreous china squatting pan "orissa" pattern, size 580 x 440 mm white, with integral foot rest (Excluding flushing cistern and flush pipe) and making good to the floor complete all as specified & directed by Engineer-in-charge.

S&F in repair, vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) P OR S trap complete all as specified & directed by Engineer-in-charge.

S&Fin repair wash hand basin oval type vitereous china flat back size 550 x 400 mm white incl CP waste coupling waste pipe brackets complete all as specified & directed by Engineer-in-charge.

S&F rotational moulded polyethylene water storage tanks 1000 litres capacity triple layered (White) cylindrical vertical with closed top hoisted and 20mm ball valves high pressure with polythene float and flynut complete fixed in position including dismantling water tank of capacity exc 500 lt but n exc 1000 ltand removing to store of any description complete all as specified & directed by Engineer-in-charge.

S&F in repair 32 mm dia., waste fittings, brass chromium plated for glazed ware sinks, wash basins etc., with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end complete all as specified & directed by Engineer-in-charge.

S&F in repair 15mm dia stop valves (concealed type) fancy type cast copper alloy chromium plated screwed down high pressure with crown or capstan head screwed both ends for iron pipe with long shank and cup complete all as specified & directed by Engineer-in-charge.

S&F in repair Vitreous china urinals with urinal spreader, half stall (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing complete all as specified & directed by Engineer-in-charge.

S&F 15 mm bore dia steel water tubing medium grade galvanised with and including necessary all fittings and fixtures complete fixed to walls and ceilings or laid in floors etc including taking down of old existing pipe complete all as specified & directed by Engineer-in-charge.

S&F 20 mm bore dia steel water tubing medium grade galvanised with and including necessary all fittings and fixtures complete fixed to walls and ceilings or laid in floors etc including taking down of old existing pipe complete all as specified & directed by Engineer-in-charge.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. loaded bedded and pointed in any mortar complete all as specified & directed by Engineer-in-charge.

M&L for 20mm thick granite stone slab machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing over and including 15mm thick screed bed in cement mortar (1:4) all as specified & directed by Engineer-in-charge.

M&L sand stone slabs 5cm thick in sun-shades, chajjas, shelves, cills, landings, cover stones, templates, etc. n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:2 or cement mortar 1:4. complete all as specified & directed by Engineer-in-charge.

S&F steel ventilators with top hung shutters fitted with box type hinges including MS peg stays, MS handle and glazing bars dovetailed or welded for receiving glass including painting with one shop coat of zinc chromate primer,and cutting holes in wall for fixing the window lugs in PCC 1:2:4 type B1 using 20mm graded aggregate and making good the disturbed surfaces in CM (1:3) and applying two coats existing wall finishes to match with existing colour complete all as specified and directed by Engineering –in-Charge. Note : The rates quoted are inclusive of making good all the disturbed surfaces to match with the adjoining surfaces and necessary scaffolding etc up to 4th floor.

S&F in repair steel window stopper peg stay complete fitting complete all as specified & directed by Engineer-in-charge.

M&L perpartion of old existing wall surfaces including cornices, plastered or un-plastered surfaces by brooming down or steel wire brushing, moss efflorescent salt and trading oil and greasy spots and applying one coat of cement base paint over and including filling up of holes by wall care putty wherever required complete all as specified & directed by Engineer-in-charge.

M&L perpartion of new wall surfaces including cornices, plastered or un-plastered surfaces by brooming down or steel wire brushing, moss efflorescent salt and trading oil and greasy spots and applying one coat of cement base paint over and including filling up of holes by wall care putty wherever required complete all as specified & directed by Engineer-in-charge.

M&L broken bricks filling of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified & directed by Engineer-in-charge.

M&L for plain cement concrete (1:4:8) type D-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified & directed by Engineer-in-charge.

M&L For applying Pitch Free PU based Liquid applied single component elastomeric seamless, water and vapor proof membrane system of equivalent material of approved makes etc. for concrete @ 2.50 kg/m2 (2 coats). Typical applications will include roofs, podiums, balconies, floor slabs, suspended floors, patios, bathrooms, inspection pits, swimming pools, bridge decks, Conforming Tensile Strength (2N/mm2 ) (ASTM D412) / Tear resistance (15 kN/m) (ASTM D624-00 and Crack bridging (ASTM C836 / ASTM C1305 modified)2mm. After 72 hours of curing, flood test can be carried out to a minimum depth of 50mm of water for 24 hours. Drains shall be plugged and barriers placed to contain the water complete all as specified & directed by Engineer-in-charge.

M&L for applying bond coat cum waterproofing on the prepared old surface of concrete/ masonry to receive new Readymade plaster/polymer mortar/ polymer modified mortar with two coats of Slurry- @ approximately 2- 2.5 m2 / litre depending on substrate porosity of equivalent material of approved makes etc. as per manufacturer specifications. Laying of reinstatement readymade plaster/polymer mortar shall be completed within the overlay time of bonding coat. This bond coat act as bonding agent between old and new concrete complete all as specified & directed by Engineer-in-charge. Note :The rate quoted by contractor shall include cleaning of surface, application as per instruction and scaffolding upto 20mtr height all as specified and directed)

Supply of SBR based waterproofing compound @ 2% dosage by weight of cement (1kgs) of 50kg cement used to be mixed in cement concrete as water proofing and hardening complete all as specified & directed by Engineer-in-charge.

Dismantling of 100 mm dia cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required of any size complete all as specified & directed by Engineer-in-charge.

S&F in repair 75 mm bore PVC (SWR) single socketed in any length with rubberring joints fixed to walls with clamps complete all as specified & directed by Engineer-in-charge.

S&F in repair 110 mm bore PVC (SWR) single socketed in any length with rubberring joints fixed to walls with clamps complete all as specified & directed by Engineer-in-charge.

S&F in repair 75 mm bore PVC (SWR) single socketed in any length with rubberring joints laid in trenches or in floors complete all as specified & directed by Engineer-in-charge.

S&F in repair 110 mm bore PVC (SWR) single socketed in any length with rubberring joints laid in trenches or in floors complete all as specified & directed by Engineer-in-charge.

S&F in repair PVC (SWR) bend any radius of 75 mm bore complete all as specified & directed by Engineer-in-charge.

S&F in repair PVC (SWR) bend any radius of 110 mm bore complete all as specified & directed by Engineer-in-charge.

S&F in repair PVC (SWR) branch piece, single(single Y), equal or unequal any radius of 75 mm bore complete all as specified & directed by Engineer-in-charge.

S&F in repair PVC (SWR) branch piece, single (single Y), equal or unequal any radius of 110 mm bore complete all as specified & directed by Engineer-in-charge.

S&F in repair PVC (SWR) vent cowl any radius of 75 mm bore complete all as specified & directed by Engineer-in-charge.

S&F in repair PVC (SWR) vent cowl any radius of 110 mm bore complete all as specified & directed by Engineer-in-charge.

M& L for PVC (SWR) floor trap of size 75mm, plain with grating including jointing with solvent cement all as directed by Eng-in-Charge.

S&F PVC(SWR) 110 mm dia P trap complete all as specified & directed by Engineer-in-charge.

S&F in repair, tubular towel rail brass chromium plated, 20mm dia, D type, 60cm long between flanges fixed with chromium plated brass screws complete all as specified & directed by Engineer-in-charge.

Dismantling/Demolition of existing roof terracing of cement/brick concrete(un-reinforced) and existing water proofing treatment of any thickness in any position on top of roof of building, cleaning surface of roof with brush/mechanical brush and with water throughly to romove all dust/dirt and loose particles to expose bare concrete roof slab and romoval of rubbish/demolished material out side MD land complete all as specified & directed by Engineer-in-charge. Note : Demolition should be done by chiselling.

M&L for PCC (1:2:4) type B-0 (using 12.5 mm graded stone aggregate) as in levelling padding course over RCC roof surface including rounded or chamferred on edges etc., with approved water proofing compound all as per manufacturer's instructuions on the roof surface to achieve requisite slope complete all as specified & directed by Engineer-in-charge. (Note :- Supply only water proofing compound shall be measured & paid separately).

Supply only Liquid water proofing compound complete all as specified & directed by Engineer-in-charge.

M&L for providing 3 mm thick APP modified memberane over RCC roof with the following specifiations :-

ITEM No. 78.00 CONTD... (a) Cleaning existing surface properly & rendering 15mm thick in CM 1:4 without using extra cement finishing surface even & smooth. (b) Apply oil bound bitumen primer @ 0.40 lit/Sqm manufactured by the same agency as that of APP with a density of 0.87 -0.89 Kg/Lit at 25 Degree Centigrade on the prepared dry roof surface. (c) Providing and Laying APP modified water proofing membrane reinforced with non wooven polyster matt with physical propertities as under :- (i) Membrane weight >3.6 Kg/Sqm . (ii) Net wooven polyster weight >160 gm/Sqm (iii) Softening point of membrane > 150o C (iv) Joint Tensile strength Longitudiual > 650 Sq Cm at 230o C & Transverse > 450/ Sq cm (v) Tear strength - Longitudual > 300 N & Transverse > 250 N Direction (vi) Elongation > 30 % (vii) Impermeability under water pressure > 3 Kg/Sq cm Note:- APP membrane shall be laid using butane torch by Torch application with minimum 10 cm side overlap and 15 cm end lap. The laying of membrane shall be got done through authorised applicator of manufacturer of membrane.

M&L for 500 micron impermeable synthetic membrane s pecifically referring to its use in ponds to prevent water leakage and seepage complete all as specified & directed by Engineer-in-charge.

M&L for precast cement concrete (1:3:6) type C1 (using 20 mm graded stone aggregate) block masonry with solid blocks, exceeding 10 cm in width and setting in cement mortar (1:6) including demolition of PCC block masonry, built in Cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles etc complete all as specified & directed by Engineer-in-charge.

M&L PCC (1:3:6) type C-1 (using 20mm graded stone aggregate) as in coping and bed blocks etc incl weathering slightly rounded or chamfered angles and throating as directed including form work complete all as specified & directed by Engineer-in-charge.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in hard/dense soil complete all as specified & directed by Engineer-in-charge.

Excavating in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes etc not exceeding 10 Sqm on plan and not exceeding 1.5 m in depth and getting out in hard/dense soil complete all as specified & directed by Engineer-in-Charge.

Returning, filling in, including, spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with hard/dense soil complete all as specified & directed by Engineer-in-Charge.

Removing excavated soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified & directed by Engineer-in-Charge.

M&L for squared rubble walling, Jodhpur type, brought upto courses, well bonded, bedded and solidly hearted, built in cement mortar (1:6) complete all as specified & directed by Engineer-in-charge.

Extra over stone walling for hammer dressing to face stones with maximum depression on face from straight edge not exc 20mm and dressing face beds and joints as specified to squared rubble walling, Jodhpur type brought upto courses complete all as specified & directed by Engineer-in-charge.

M&L for 40mm thick cement concrete of 1:2:4 type B0 using 12.50mm graded stone aggregate as in Damp proof course to horizontal or vertical surfaces including necessary formwork complete all as specified & directed by Engineer-in-charge.

Material and Labour for Hard core of Guage n.exc 63mm, deposited, spread and levelled in layers n.exc 15cm thick, watered and rammed to a true surface with broken stone boulders complete all as specified & directed by Engineer-in-charge.

M&L for 75 mm thick plain cement concrete (1:3:6) type C-2 (using 40 mm graded stone aggregate) as in sub base of flooring/ hard standing & finished the surface even & fair without using extra cement complete all as specified and directed by Engineer-in-charge.

M&L Machine cut kota stone slab flooring 20-25mm thick over, laid over cement screed base , jointed and pointed with grey cement slurry mixed with pigment over 20mm thick cement mortar 1:6 screed bed to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engineer-in-charge.

M&L Machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar over 10 mm thick cement plaster 1:3 jointed and pointed with grey cement slurry mxed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engineer-in-charge.

M&L for Jodhpur stone roof slabs, self faced 7.5cm to 10cm thick, 25cm to 35cm wide, hoisted and set, jointed and grouted in cement mortar 1:3 complete all as specified and directed by Engineer-in-charge.

Material & Labour for 5 mm thick rendering in cement mortar (1:3) on ceiling of any description finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-charge.

Material & Labour for 15mm thick rendering in cement mortar (1:6) on brick or concrete surface (fair or other than fair) of any description finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-charge.

Material and labour for 15 mm thick rendering in cement mortar 1:4 on fair faces brick work, stone masonry or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-charge.

Material & Labour for preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over 1mm thick wall care putty on plastered for neat and smooth finishing including preparation complete all as specified and directed by Engineer-in-charge.

M&L for preparation of newly plastered surfaces and applying two coats of cement based paint over a coat of primer complete all as specified & directed by Engineer-in-charge.

M&L for Roughly squared jodhpur stone lintels hammer dressed on face and soffits, hoisted, set and pointed in lime mortar 1:3 or cement mortar 1:6 complete, n exc 3m in length complete all as specified & directed by Engineer-in-charge.

M&L for 75 mm thick PCC (1:3:6) type C2 (using 40 mm graded stone aggregate) laid in alternative bays as in plinth protection including finished the surface even & fair without using extra cement & filling the joints with mastic filling i.e one part of bitumen 85/25, 3 parts of sand by weight complete all as specified and directed by Engineer-in-charge.

Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound grade A complete all as specified and directed by Engineer-in-charge.

S&F Steel windows with side hung shutters including friction/projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed by Engineer-in-charge.

M&L for plain sheet glass plain 3mm thick ordinary quality and glazing with oil putty in square n. exc 0.5 Sqm in each pane complete all as specified and directed by Engineer-in-charge.

S&F Aluminum anodised bow handle, bearing ISI mark, fabricated type extruded section of 150mm long complete all as specified and directed by Engineer-in-charge.

S & F 150 mm over all length of cover plate of floor door stopper, bearing ISI mark, of aluminium alloy body and tongue, anodised with hard drawn steel spring, complete all as specified and directed by Engineer-in-charge.

M & L for Framed work as in grills with ends of bars shoulders or framed guard bars and similar work conforming to Fe-290 Gde-E-165 complete all as specified and directed by Engineer-in-charge.

Taking down carefully surface aluminium or copper point wiring with PVC casing-caping (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc and making good disturbed surfaces complete all as specified & directed by Engineer-in-charge.

Taking down the existing unserviceable main switch / cut out / DBs of any type / capacity / description as existing at site including MCBs any type and capacity making good the disturbed surfaces to match with the existing finishes complete all as specified & directed by Engineer-in-charge.

M&L point wiring used approved colour coding as per IS (Red, Black and Green) for single phase circuits), with multi-stranded copper conductor 1.5 sqmm nominal cross -sectional area, single core, PVC insulated and unsheated FRLS cable 1100 volts grade, ISI 694 marked with valid CML No. in and including medium grade, PVC concealed conduit MMS, ISI marked of dia not less than 20 mm and conduit accessories conceled in wall/roof/floor etc, ISI marked with valid CML No. (IS-9537 - 1983 for condits and IS : 3419 - 1976 for conduit accessories) with terminated to new pressed flush metal boxes readily available cover with outer plates inner plates et, suitable for mounting modular type switches, socket fan regulator etc PVC insulated multistanded copper conductor 1.5 Sqmm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for the following :- Note : Modular switch and socket shall be measured and paid separately.

One light point controlled by one switch

One ceiling fan/exhaust fan point controlled by one switch

One socket outlet 6 amp controlled by one switch on the same board with other switches.

All as per item No 109.00 here on before but with copper conductor cable of nominal class area 4.0 sq mm for phase, neutral & earth for power socket point 15 A .

S&F modular switch one way 6A, 1 module complete all as specified & directed by Engineer-in-charge.

S&F modular socket 6A-2/3 pin combined 2 module complete all as specified & directed by Engineer-in-charge.

S&F modular switch socket combined 6A/16A , 6 pin, 3 module complete all as specified & directed by Engineer-in-charge.

S&F Ceiling rose, three terminals PVC/polycorbonate, isolated body complete all as specified & directed by Engineer-in-charge.

S&F for MCB DB SPN 8 way double door IP 43 complete prewired including Bus Bar etc suitable for operation on 240 volt 50 Hz AC supply including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified & directed by Engineer-in-charge.

Supply and fixing MCB's single pole and neutral 32 Amps, 240 Volts,10 KA rapturing capacity 'C' curve complete all as specified & directed by Engineer-in-charge.

Supply and fixing MCB's single pole 10 Amps to 32 Amps, 240 Volts,10 KA rapturing capacity 'C' curve complete all as specified & directed by Engineer-in-charge.

M&L for submain wiring with approved colour code/as per IS (Red, black & green for single phase) circuit with two single core PVC insulated cable with multistranded copper coductor of nominal cross sectional area of 4.0Sq mm (FRLS) in and including Concealed conduit non metallic including one run of PVC insulated multistranded copper conductor nominal cross section area of 4.0 Sq mm (FRLS) of continuous earth wire green in colour including taking down old u/s sub-main wiring complete all as specified and directed by Engineer-in-charge. Note: Two runs of 4.0 sqmm cable & One run of 4.0 sqmm cable and One run of Concealed conduit shall be paid as one unit length.)

Supply and fixing LED lights fitting 1x 18W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified & directed by Engineer-in-charge.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified & directed by Engineer-in-charge.

Supply and fix exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper winding of sweep 250 mm complete all as specified & directed by Engineer-in-charge.

Taking down ceiling fan / exhaust fan/wall fan/air circulator fan of any sweep sealing cable ends dismanting blade and removing fan and blade to store complete all as specified & directed by Engineer-in-charge.

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc complete all as specified & directed by Engineer-in-charge.

S&F 15 mm dia bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule fancy type and fixed complete all as specified & directed by Engineer-in-charge.

M&L for PVC connection pipe chromium plated 15 mm dia both end threaded incl brass coupling bolt cone washer complete, length of pipe is not less than 450 mm suitable for Hot/ cold water system complete all as specified & directed by Engineer-in-charge.

S&F 15 mm dia stop valves, cast copper alloy,screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified & directed by Engineer-in-charge.

M&L for 15 mm bore of new Gl steel tube medium grade galvanized with all fitting laid in trenches/ on wall/ ceiling/ roof complete including wall cutting, fitting of pipes and making good surface as per existing surface complete all as specified & directed by Engineer-in-charge.

M&L for 20 mm bore of new Gl steel tube medium grade galvanized with all fitting laid in trenches/ on wall/ ceiling/ roof complete including wall cutting, fitting of pipes and making good surface as per existing surface complete all as specified & directed by Engineer-in-charge.

M&L for submain wiring with approved colour code/as per IS (Red, black & green for single phase) circuit with two single core PVC insulated cable with multistranded copper coductor of nominal cross sectional area of 4.0Sq mm (FRLS) in and including Concealed conduit non metallic including one run of PVC insulated multistranded copper conductor nominal cross section area of 4.0 Sq mm (FRLS) of continuous earth wire green in colour complete all as specified and directed by Engineer-in-charge. Note:- Two runs of 4.0 sqmm cable & One run of 4.0 sqmm cable and One run of Concealed conduit shall be paid as one unit length.)

S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20Amp all as specified.

S & F for MCB DB SPN 4 way double door IP 43 complete prewired including Bus Bar etc suitable for operation on 240 volt 50 Hz AC supply including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed .

AMBEY MAA CONSTRUCTION COMPANY (BID ID -3439736)

SHIVA CONSTRUCTION COMPANY (BID ID -3438824)

M/s Shri Inder Construction Company (BID ID -3438607)

AMR TRADERS (BID ID -3438773)