138WE/L-30/2022-23

Amount

Rough Excavation not exceeding 1.5m deep and getting out in hard/dense soil complete all as specified and directed by Engr-in-Charge.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard /dense soil

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm

M & L for Cement concrete type D2 1:4:8 (40 mm graded aggregate) in foundations, filling and mass concrete

M & L for Reinforced cement concrete (design mix) M-25 ( 20 mm greded aggregate) in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete

M & L for Reinforced cement concrete (design mix) M-25 ( 20 mm greded aggregate) in Columns, pillars, piers, posts and struts.

M & L for Reinforced cement concrete (design mix) M-25 ( 20 mm greded aggregate) in Beams, cantilevers, bressummers, lintels over 1.5m span

M & L for Reinforced cement concrete (design mix) M-25 ( 20 mm greded aggregate) in chajjas

M & L for Reinforced cement concrete (design mix) M-25 in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete, all as spd.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc

Formwork to sides of Rough finished surfaces concrete pillars, posts, struts, piers, columns and stanchions

Formwork to soffits of Rough finished surfaces concrete suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping)

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide

Formwork to Rough finished surfaces concrete chullah hoods, chajjas, troughs and similar items including edges

M & L for Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

All as per item above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders

M & L for Pre-cast cement concrete block masonry type C-1 1:3:6 (20 mm greded aggregate) with solid blocks, exc. 10 cm in width and setting in mortar 1:6, complete

M & L for sand filling under floors or in foundation incl watering and consolidation.

M & L for Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface

M & L for PCC 75 mm thick 1:4:8 type D2 (40 mm graded aggregate) as in sub base

M & L for PCC 25 mm thick 1:2:4 type B-1 (20 mm graded aggregate) as in floor

M & L for PCC 40 mm thick 1:2:4 type B-1 (20 mm graded aggregate) as in Damp proof course

M&L Brushing neat cement slurry with 3.0kg of cement per sq. metre

M & L for Screed bed or bedding layer of mortar in 1:4 for 15 mm thick for laying floor finishes

M & L for coloured non-skid ceramic tiles 400x400x7 mm thick in flooring set & jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles including 15 mm thick cement mortar screed bed or bedding layer in CM 1:6 complete all as specified and directed by Engr-in-charge.

M & L for Glazed ceramic tiles in vertical surface 300x 200x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match incl 10 mm thick cement plaster in cm 1:3 as in bedding layer

S & F for 2nd class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints.

S & F for Factory made shutter 35 mm thick 2nd class hardwood Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated all as specified and directed by Engr-in-charge.

M & L PCC type B-1 1:2:4 (20 mm graded aggregate) for fixing hold fast

S & F MS flat iron of size 25x3 mm as in hold fast conforimg to Fe 410-0 or Fe-310-0

M&L 15 mm thick cement plaster in cement mortar 1:6 on brick or concrete surface etc. on wall finished even and smooth without using extra cement, all as specified.

All as per item above but in ceiling surface

M&L Rendering 15 mm thick on fair faces of brick wall or cement concrete surface in cement mortsr 1 :4 finished even and smooth without using extra cement, incl mixing of water proofing compound all as specified. (Note - Water Proofing Compound shall be measured and paid for separately

Supply only liquid water proofing compound.

M&L75 mm thick in PCC type C-1 1:3:6 (using 20 mm graded aggregate crushed stone aggregate) as in plinth protection laid in alternate bays (not exc 2 Sqm each) finishing even smooth at top without using extra cement and providing joints throughout the thickness filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight all as specified and directed at site.

M&L Factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing of MES SSR 2020 Part - II and as directed by the Engr-in-Charge

M&L factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing of MES SSR 2020 Part - II

S & F 3.00 mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane, all as specified.

S & F Figured glass, pin head type 3 mm thick, confirming to SI-5437 (1969) and glazing with oil putty in squares n exc 0.5 sq. m in each pane all as specified.

S & F M S cold rolled butt hinges medium weight 100 mm long (ISI marked)

S & F Aluminium anodised, barrel tower bolts of extruded section with 150 mm long bolt and fixed all as specified

All as per item above but 100 mm long

S & F Aluminium handles, cast type, anodised 125 mm size complete all as specified

All as per item above but 100 mm long

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, 250 mm long

S&F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, 150 mm long

S&F 2nd class hardwood Small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary' labours; articles n exc 200 cu. cm each

M&L 15mm Steel water tubing medium grade galvanised with all fitting incl short length, fixed to wall, concealed in wall or ceiling or laid in floor complete with all fitting (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.)

M&L 20mm Steel water tubing medium grade galvanised with all fitting incl short length, fixed to wall, concealed in wall and ceiling or laid in floor complete with all fitting (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.)

S&F Tubular towel rail,600 mm long of brass chromium plated fixed with and incl chromium plated brass screws and wooden / plastic cleats all as specified.

S&F Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 20 mm bore and fixed all as specified

S&F Fancy type, Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe of bore 15 mm and fixed all as specified.

S&F Bib taps, short body, fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe of 15 mm or for brass ferrule and fixed, all as specified

S&F PVC connection 15 mm size with PTMT nuts of length 450 mm.

S&F gun metal globe or gate valve with iron wheel 20 mm dia

S&F vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe)

S&F Vitreous China wash basin, with pedestal, coloured, flat back of size 550x400 mm excluding brackets cutting for and pinning in ends of brackets or erecting stands also incl brass chromium plated waste cuplling 32 mm dia pipe Waste coupling of PTMT (half or full threaded) . (Minimum weight 32mm45gms/40mm-60 gms PVC connections 15mm size 450 mm lenght with PTMT nuts, fixed all as specified

S&F Low density polyethylene 32 mm dia (LDPE) pipes of pressure rating 6 kgf/sq. cm complete, fixed to sink/wash hand basin colplete all as specified.

S&F fittings for CI Pipes for Bends 75 mm radius, diminishing pieces or tapers (larger bore measured)

S&F fittings for CI pipes for branch pieces 75 mm size, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches

S & F cast iron cowels 75 mm bore all as specified.

S & F 75 mm dia cast iron soil, waste and vent pipes (ISI marked) sand in any length with or without ears, with cement joints complete fixed, laid in trenches or in floors or wall or in any places complete all as specified.

M&L preparing plastered new surfaces of wall and applying two coats of cement base paint over a coat of cement primer all as specified.

Preparing of new surface of wall of any description and applying two coats of distemper oil emulion over a coat of primer all as specified.

M&L preparation of new surface of ceilings of any description and appying three coats of white washing, all as specified.

M&L prepration of new wooden or wood based Surfaces of any description, not otherwise descri-bed, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, all as specified.

S&F PVC valveless, syphonic action type, flushing cistern of capacity 10 ltr, low level, white, with inlet, ball valve, manually operated with one PVC ball valve horizontal pluger type incl provision of 32 mm PVC flush pipe of required length and making connections complete.

M&L providing, cement concrete Type B-1 1:2:4 (using 20 mm graded aggregate) as in stagging on roof for water tanks in roof kerbs or mud stops, rounded or chamfered angles and throating as directed incl use of form work complete.

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I of capacity 500 ltr incl all accessories, all as specified.

S&F Steel rolling shutters, with out ball bearing, as specified including top cover, an?choring rod, hasp and staple and one shop coat of primer; erected in position as indi?cated, complete: push pull or manual type

Surface dressing n exc 15cm deep in hard/dense soil.

Excavation over areas n. exc 1.5m deep and getting out in hard/dense soil.

Excavation over areas exc 1.5 deep and n. exc 3.00m deep and getting out in hard/dense soil.

M&L for walling of random rubble stone masonary, uncoursed well bound, bedded and solidly hearted, laid dry complete all as specifed and directed.

M&L for TMT bars, 6 to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

M&L for reinforced precast cement concrete 1:2:4 type B-1 using 20mm graded aggregate as in cover slab for manhole set in CM 1:4 including necessary form work complete all as sepicified and directed by Engr-in-Charge.

M&L framed work such as framwork of manhole cover conforming to Fe 290 Gde E-165

M&L for loose filling with broken bricks aggregate of gauge 80 to 150mm in soakage pit, soakage wells

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints as specified, of random rubble walling, uncoursed or brought upto courses.

M&L for raised pointed to squared rubble masonary, coursed, or uncoursed CM (1:4) on stone masonary.

S&F for PVC (SWR) pipe 75mm dia laid in retaining wall as a weep holes complete all as specified and directed.

M&L for cement concrete 1:3:6 type C-1 using 20mm grated stone aggregate as in coppings, brands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in heights, kneelers, apex stones, bed plates, kerbs water troughs and the like including weathering, slightly rounded or chamfered angles and throating as directed.

M&L for precast reinforced cement concrete1:3:6 type B1 using 20mm graded stone aggregate as in bond stone etcand set in cement mortar 1:6 including use and waste of necessary formwork all as specified and directed.

M&L for point wiring complete with single core FRLS PVC insulated, unsheathed, multi stranded copper conductor cables 1.5 Sqmm 1100 volts grade, with and incl 1.5 Sqmm FRLS PVC insulated, unsheathed, multi stranded copper conductor cables as continuous earth wire connected to metallic bodies of luminaries / fans etc at one end and to common earth dolly at other end, complete concealed wiring drawn through PVC conduit of 19 mm and above (as per conductor run ) medium grade, ISI marked, incl all accessories & fittings / junction boxes / inspection covers etc, with and incl concealed MS sunken box of suitable size flush with wall surface, covered with & incl 3 mm thick bakelite, laminated hylem sheet / Gang box for top cover suitable for fixing of switches / sockets etc, complete all as specified and directed for Light/Fan Point controlled by one switch.

Ditto as per item here-in-before but for one socket outlet 3 pin, 5 Amps on independent board.

Ditto as per item here-in-before but for one socket outlet 3 pin, 5 Amps on same board.

Ditto as per item here-in-before, but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor (Multi-stranded) insulated and unsheathed electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 2.5 Sqmm copper stranded conductor as continuous earth wire connected to common dolly complete all as specified and as directed by Engineer-in-Charge. Note : The point wiring for power point will not be mixed with light/fan point circuit or not in the same conduit pipe.

M &L for Switch piano flush type, single pole, one way, 5 amps, 230 volts, as specified and directed by Engr-in-charge.

Supply and fixing socket 2 in 1, 5 Amp, flush type complete all as specified and as directed by Engr-in-charge.

M & L for Switch Socket Combination, two-in-one, 5 pin, 5 Amp,flush type, 230 volts, complete all as specified and directed.

M & L for Switch Socket Socket combination, 6 pin, 5/15 Amp, multipurpose shutter type, 230 volts, complete all as specified and directed.

M & L for Ceiling rose, three terminals, bakelite body, 230 volts, complete all as specified and directed.

Supply and fixing LED batten lights fitting 1x 18W, 220V, AC decorative type with driver, connecting up with three core flexible copper conductor cable of suitable size upto ceiling rose complete all as specified and directed by Engr-in-Charge.

Supply and fixing angular lamp holder, PVC/Polycaronate type with back plate suitable for LED bulb for batten fittings complete all as specified and directed by the Engineer-in-Charge.

Supply and fixing LED Bulb 12 Watt, 6500K complete all as specified and directed by Engr-in-Charge.

S&F DB, double Door, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, TPN 4 way, 415 volts with bus bar rating 200 Amps, dust and vermin proof, suitable for incorporation of MCB’s and isolators etc and making all necessary connections, duly flush of wall surface, complete all as specified and directed.

S&F MCB, B Curve type, 10 kA, 32 Amp, TPN with over load and short circuit protection, complete all as directed.

S&F MCB, B Curve type, 10 kA, 6 to 32 Amp, SP with over load and short circuit protection, complete all as directed.

M&L for earthing with galvanized steel earth plate electrode of size 600 x 600 x 6 mm buried directly in ground earth pit not less than 2.25 mtr below of normal ground level with top edge of earth plate should not less than 1.5 mtr below normal ground level and connected to galvanized iron earth lead wire of size 4 mm dia by means of bolts, nuts, washers of galvanized iron or steel all as shown in electrical plate No.3 of MES SSR Part I connecting to earthing test point on completion with and including 15 mm bore GI light grade protection pipe (7.5 mtr long) for earth lead GI lead wire 4mm dia (7.5 mtr long), PCC pit with cover in PCC 1:2:4 type B-1 reinforced with 8 mm dia tor bars @ 80mm C/C, 20mm dia medium grade watering pipe with funnel, wire mesh, common salt, charcoal, necessary excavation and earth work, complete all as specified and directed.

Supply and fixing new energy saving LED Bulk head fitting 12 watt made up of pressure die cast aluminium housing with acrylic cover as diffuser with IP 66 protection and impact resistance of IK07 as reqd to be mounting bracket in wall/floor to suit the opening of the fitting with FI clamp, nut, bolt and washers of suitable size including making connection complete all as specified and as directed by Eng-In-Charge

Supply and fix exhaust fan made metal body complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm complete all as specified and directed by Engr-in-Charnge.

M&L for sand cushioning with layer of sand 8cm thick before laying of cable and 15cm after laying, streching & testing of cable in trenches complete all as specified and directed by Engr-in-Charge. Note :- Only punned thickness i.e 18cm shall be measured and paid.

Material and labour for un-reinforced pre-cast concrete cable covers, class LV type-1, flat size 250mm x 150mm x 40mm thick complete all as specified and directed by Engr-in-Charge.

Material and labour for un-reinforced pre-cast concrete cable covers, class HV type-1, flat size 300mm x 180mm x 40mm thick complete all as specified and directed by Engr-in-Charge.

Material and labour for PCC 1:3:6 type C–2 (using 20 mm crushed graded stone aggregate/as in foundation for stay & copping and necessary form work for rough finished surface complete all as specified and as directed.

Supply and fixing tubes, Light grade galvanized with all fitting and fixed complete to walls/ poles/ ceiling or laid in floor of size 50 mm bore for the protection of UG cables including dismantling/ taking out old, unserviceable one complete all as specified and as directed by Engr-in-Charge.

Supply and erection in vertical position steel tubular swaged pole type 410 SP- 55 (11 mtr long ) with Mild Steel base plate of size 30cmx30cmx6 mm thick continuously welded to pole , finial taper plug ,bolts ,nuts and screws all as specified including factory painted with two coats of black bituminious paint internally throughout and externally for embedded position and two coats of aluminium paint over a coat of red oxide primer over the ground and making 30cm wide strip (total 5 Nos ) with black and yellow paint including numbering complete all as specified by Engr-in-Charge.

Supply, installing, testing , connecting and commissioning of distribution transformer outdoor type step down 11/0.433 KV (at no load) with HT 3 phase and LT 3 phase 4 wire AC , 50Hz, 315KVA level - II, copper wound with off load tap changing arrangement on HT side for a variation of secondary voltage +/- 7.5% in steps of +/- 2.5% including suitable cable entry boxes on LT side and HT bushing on primary side complete in all respects with standard accessories and fitments confirming to IS: 1180 amended upto date and test ECBC as specified and directed inlcuding the followings.(a) Earthing terminal and rating diagram plate. (b) Air release device (c) Oil Filling inlet pipe with plug. (d) Drain outlet pipe with brass gate valve with dummy plug. (e) Conservator with level gauge. (f) Silica gel with breather. (g) First oil fill up to the recommended level by the manufacturer with new oil confirming to IS 335. (h) Type of connector - Star/Delta. (j) Type of Cooling - ONAN (k) Vector Group- DYN 11 (l) Type of connecting arrangement - HT XLPE cable connection on HT side and cable connection on VCB side. (m) Provision of thermometer with pocket. (n) Oil and winding alarm and trip relay including marshal box. (o) The transformer of 315KVA full capacity shall be designed to fuction properly at high altittute of appx 3865M above sea level and outside temperature conditions between -40 degree celcius to +30 Degree celcius. (p) Factory inspection shall be carried out for transformer.

M & L For Danger notice plate of 1.6mm thick mild steel sheet, vitreous enamelled white, with letters, figures and conventional skull and bones in signal red colour and fixed with M.S. clamps, bolts and nuts of approved size, for LT, 20x15cm size complete all as specified and directed by engr-in-charnge

Supply & install 11 KV 3 Phase Gang operated air break switch with drop out fuses set ( consisting 12 Nos Post Insulator ) 400 amp capacity, vertical mounting with fixed and moving contacts complete with locking arrangement and fixing the gang operated switch on existing two/four pole structure including making all jumper connections with insulated leads of suitable size with line tops etc, all as specifed and directed.

S&F Aluminium Conductor Steel Reinforced (ACSR), weasel conductor (sizes as ordered) and fixing on Electric Poles with binding to Insulators with Aluminium Binding Wire as in OH Conductors including Stringing, Tightening, complete all as specified and as directed by Engr-in-Charge.

M & L for galvanised steel wire 4 mm dia to be stringed as continuous earthing/ Guard wire on over head HT lines complete all as directed by Engr-in-Charge .

M & L for Stay Assembly complete with Accessories as show in Electrical Plate No. 1 of MES Schedule Part-I, diameter of Stay Rod 16mm, size of Plate 150X150 X6mm including 7/3.15mm Galvanised Stay Strand One Loop Type Insulator Vitreous Porcelain, White Brown or Green, Small size with Overall dimensions 65X90mm, Clearance of Hole 16mm dia, complete all as specified and as directed Engr -in-Charge.

S&F cross arms, bracing ,supports clamps & back plates fabricated from structural steel section including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of paint complete all as specified and directed by Engr-in-Charge.

Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metres below normal ground level, connecting to the Galvanised iron strip 32x6 mm by means of bolts, nuts , check nuts and washers of galvanized iron and steel earth wire protected by provision of GI light grade pipe 15mm bore including provision of concrete pit made from PCC ( 1:2:4) type B-1 (using 20 mm graded stone aggregate) with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4 Kg/Sqm) and frame of angle iron 40 x 40 x 6 mm and handle of 6 mm dia MS bar made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom, 1.50 metre long placed on top edge of earth plate, common salt & charcoal filling, with fixing arrangement , funnel, wire mesh and earth work in hard/dense soil , returning filling in and removal of surplus soil to a distance not exceeding 50 metres, all as per electrical plate No 3 of SSR 2009 Part-I and connecting to Transformer / Poles all as specified or indicated including testing on complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for XLPE insulated screened , PVC Bedded, galvanised steel strip armoured , electric power cables(heavy duty ) with aluminium conductor, 11000 volts grade cross sectional area 120 Sqmm 3 Core, laid in trenches, ducts along the walls, through pipes,or fixed on pole etc complete all as specified and directed by Engr-in-Charnge.

Material and Labour for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade cross sectional area 400 Sqmm 3.5 Core, laid in trenches, ducts along the walls, through pipes,or fixed on pole etc complete all as specified and directed.

Material and Labour for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade cross sectional area 300 Sqmm 3.5 Core, laid in trenches, ducts along the walls, through pipes,or fixed on pole etc complete all as specified and directed.

Material and Labour for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade cross sectional area 240 Sqmm 3.5 Core, laid in trenches, ducts along the walls, through pipes,or fixed on pole etc complete all as specified and directed.

Material and Labour for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade cross sectional area 150 Sqmm 3.5 Core, laid in trenches, ducts along the walls, through pipes,or fixed on pole etc complete all as specified and directed.

Material and Labour for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade cross sectional area 120 Sqmm 3.5 Core, laid in trenches, ducts along the walls, through pipes,or fixed on pole etc complete all as specified and directed.

Material and Labour for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade cross sectional area 95 Sqmm 3.5 Core, laid in trenches, ducts along the walls, through pipes,or fixed on pole etc complete all as specified and directed.

Material and Labour for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade cross sectional area 50Sqmm 3.5 Core, laid in trenches, ducts along the walls, through pipes,or fixed on pole etc complete all as specified and directed.

Material and Labour for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade cross sectional area 35Sqmm 3.5 Core, laid in trenches, ducts along the walls, through pipes,or fixed on pole etc complete all as specified and directed.

Material and Labour for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade cross sectional area 25Sqmm 4 Core, laid in trenches, ducts along the walls, through pipes,or fixed on pole etc complete all as specified and directed.

Material and Labour for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade cross sectional area 16Sqmm 4 Core, laid in trenches, ducts along the walls, through pipes,or fixed on pole etc complete all as specified and directed.

Material and Labour for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade cross sectional area 10Sqmm 4Core, laid in trenches, ducts along the walls, through pipes,or fixed on pole etc complete all as specified and directed.

M&L for Pin Insulators, porcelain, vitreous white, brown or green insulators including one galvanised mild steel spindle, two galvanised iron washers one galvanised iron nut, 150 mm hight 150 mm dia for 11000 volts grade complete all as specified and as directed by Engr-in Charge.

M&L for disc type insulators, porcelain, vitreous 145 mm high and 255 mm dia ball and socket type, white, brown or green single disc assembly for 11000 volts grade complete all as specified and as directed by Engr-in Charge.

M&L for loop type insulators, vitreous porcelain, white brown or green large size, with overall dimensions 90 mm x 140mm, clearance of hole 25.5 mm for 11000 volts grade complete all as specified and as directed by Engr-in Charge.

M&L for HT lightning arresters expulsion type complete with all fittings transmission class discharge capacity of 65 KA suitable for 11000 volts lightening arester complete all as specified and as directed by Engr-in-Charge. Make: Oblum, BHEL , Crompton & Greaves, MEI, Alpro, Alstom Etc.

M&L for anti climbing divice spikes type fabricated out of MS bar(round square and flat) includiong nuts bolts and washer and welding in two halves made to shape to suit the cross section of pole, suitable for pcc/ steel tubulor poles including two coats of synthetic enamled paint over a coat of red oxide primer complete all as specified and directed by Engr-in-Charge.

Supply and fix Cable jointing kit for 11 KV (Earthed) grade cable for outdoor termination cold shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 120 Sqmm to 185 Sqmm complete all as specified and directed by Engr-in-Charge.

M&L for PCC platform of size (4 x 3 x 1.2) mtr incl earth work with PCC masonary XPM fencing around steps on one side & iron gate with locking arrangement and painting of platform/fencing/gate for transformer of capcaity 250KVA to 500 KVA complete all as specified in Drg No CESZ/TD- 1110/2011 all as specified and directed by Engr-in-Charge.

Excavation in trenches exceeding 1.5 m wide and not exceeding 3.0 m depth for foundation of poles and getting out in hard/dense soil complete all as specified and directed by Engr-in-charge.

Intrernational Engineers