ADDN/ALTN AND SPECIAL REPAIR CERTAIN BUILDINGS NO P-3 (MI ROOM), P-11 (PUMP HOUSE), P-46 (OLD POL STORE), P-71 (SAGAR I AC PLANT ROOM), P-72 (GENERATOR ROOM), P-74 (UPS ROOM), P-76 (BATTERY ROOM) AND P-108 (PROJECT PANTHER ROOM) AT HQ 31 WEU THANE

Amount

Taking down cement plaster on brick or concrete surfaces etc, including raking out joints, hacking for key, scrubbing down with water , etc complete all as specified and directed.

Taking down carefully aluminium sliding window shutters including existing rubber gasket completed and re-fixing the shutters same in existing position after replacement of broken glass/stainless steel wire mesh with rubber gasket and area of window exc 1.20 sqm but not exc 3.78 Sqm in each including necessary scaffolding etc complete all as specified and directed.

Taking down carefully aluminium sliding window shutters from the frames or chowkhat and supply and fix New locking arrangement in place of old one and re-fixing the same shuters in existing position after repair work or replacement of new locking arrangement and necessary scafolding etc complete all as specified and directed

Taking down chowkats or frame with shutters ( without taking off shutters from the frame ) not exceeding 1.5 Sqm each including complete all as specified and directed.

Taking down chowkats or frame with shutters ( without taking off shutters from the frame ) exceeding 1.5 Sqm but not exc 4 Sqm each including complete all as specified and directed.

Taking down rolling shutters area n.exc 10 sqm each and re-fixing to its original position after cleaning all parts, straightening rails, changing damaged strips, bottom rail,guide rail, helical spring worm gear, lock plate etc as required, greasing, oiling, servicing for smooth functioning of all parts complete all as directed.Note: Lath strips, bottom rail, spring,gears etc. will be measured and paid seperately as supply only

Taking up or down steel tubing and connections, including cleaning serviceable pipe for refixing and balance under schedule of credit all as specified and directed (a)15mm bore

(b) 20 mm bore

S&F GI Steel tubing medium grade with all fitting & fixed complete to walls & ceiling or laid in floors complete all as specified for the following size :- (a)15 mm bore

(b) 20 mm bore

Fixing only GI steel tubing medium grade with all fitting & fixing to walls/ceiling or laid in floor and complete all as specified for the following size :- (a)15 mm bore

(b) 20 mm bore

M&L for rendering 15mm thick on fair faces of brickwork or concrete surfaces in CM 1:6, finished the surfaces even & smooth including 1mm thick sagol finish complete all as specified.

M&L for rendering 20mm thick in cement mortar 1:4 on brick or concrete surfaces, on walls, laid in two layers, 1st layer 15mm thick and finishing layer 5mm thick mixed with integral water proofing compound @2 % by weight of cement content of finishing layer, finished fair and even without using extra cement , additional thickness provided as floating/setting coat, including all necessary scaffolding / staging as required complete all as specified and as directed by the Engineer-in-charge at any position.

M& L rendering 10 mm thick in CM 1:3 on ceiling surface finished even & smooth with sagol finish complete all as specified.

Supply only integral water proofing compound.

Chipping, removing carefully loose/damaged concrete including plastering (total thickness upto 60mm ) from surfaces of RCC members, in any location by low impact Hammer/Breakar without damaging the structure & cleaning the surfaces with wire brush etc and disposal of debris out side MOD land complete all as specified and directed. Note : 1) Hard concrete shall not be removed by force.

M&L for building up the profile of structural members by using polymer modified mortar from M/s. Krishna Conchem (Molith-PMM) OR Polymer mortar HB of Dr Fixit, upto 20mm thickness including levelling, profiling etc complete all as specified and directed.

M&L for building up the profile of structural members by using polymer modified mortar from M/s. Krishna Conchem (Molith-PMM) OR Polymer mortar HB of Dr Fixit while the bonding agent is still tacking, exceeding 20mm thickness and not exceeding 40mm thickness in two layers, each layer not exceeding 20mm, including levelling, profiling etc, complete all as specified and directed.

M&L for cleaning existing reinforcement with wire/ rotary wire brush to a shining bright finish, making the surfaces free from loose material, dirt etc complete and applying two coats of alkaline rust converting primer conforming to ASTM-B-117 of make. "Feovert" of "Krishna Conchem" OR "Roff Rust Cleaner' of 'Pidilite' OR 'Shali Rustoff' of 'STP Ltd', on rebars with time interval of 1 hour between the coats, complete all as specified and directed. [Note :- Mode of measurement: superficial area covered between the end to end reinforcement bars (i.e., concrete area excluding all side covers) will be measured.]

M&L for Anticorrosive Treatment to Reinforcement using IPNET-RB of M/s Krishna Conchem or Epoxy Zinc Primer of M/s. Dr. Fixit by application on exposed reinforcement in two coats with time interval of minimum 4 hours between each coat. The application shall be done by brush after cleaning/wire brushing to the exposed steel surfaces complete all as specified and directed. Note :- Mode of measurement: superficial area covered between the end to end reinforcement bars (i.e., concrete area excluding all side covers) will be measured.

M & L preparing new surfaces of walls applying two coat of oil bound distemper over 3mm thick wall care putty complete all as specified & directed by EIC.

M& L for preparation of newly plastered surface and applying three coat of white wash on ceilings complete all as specified and directed

M & L for preparing old decorated surfaces of wall (plasterered or unplastered or previously white washed) & applying two coat of oil bound distemper complete all as specified.

M & L for preparing old decorated surfaces of ceilings(plastered or unplastered or previously white washed) & applying three coats of whitewash complete all as specified.

Material & Labour for preparation of new plastered surfaces of wall applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces complete all as specified and directed.

S & F in repairs harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc

S & F in repairs Vitreous China wash basin, white, flat back, size 580x450 mm including brackets, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified and directed.

S&F standard aluminum section powder coated in partition / frame and door shutter, sliding windows / ventilators and places otherwise not specified cut to size, jointed with cadmium plated steel screws, including rubber beading or gaskets for fixing glass or wire cloth or Bakelite sheet and all necessary fittings, hinges, screws, plugs, locking arrangements for windows, Nylon ball bearing etc completed all as specified and directed (Aluminum section shall be of make Jindal / Hindalco / Indalco). Note :- Weight of Aluminum sections for frames and shutters shall be only considered for payment. Cost of other consumables required for the item shall be deemed to be included in the quoted rate. However glass panes / Bakelite sheet / wire cloth / mortice lock / locking stay / floor spring / floor door stopper only will be measured and paid separately under respective items as supply only. Fixing by element of these items shall be deemed to be included in quoted rate.

S & F in repairs aluminium anodised grill DG-104/DG-102 10 mm dia of extruded aluminium section of suitable size and frame including fixing with U clip or F section beading complete with all fitting and fixture and drilling required in RCC section in rectangular or arch type balcony opening of the building complete all as specified. (Make:- Deco Grill or equivalent)

Supply only 3.00 mm thick sheet glass, ordinary quality, in squares not exc 0.5 Sqm each pane, complete all as specified.

S&F inrepair Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples Stainless steel wire cloth. 0.36mm nominal dia of wire and verage width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

S& F second class hard wood , plain ,soild ,straight chowkats and frames, wrought , rebated on soild rounded or chamfered , put together with gule pinned at joints etc complete all as specified .and directed

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with Square tube, supply and fixing in opening as per specification given under SSR Part II 2010 including making good the disturbed surface all as specified and directed. Make: SYNTEX/SHALIMAR/RAJSHRI

M&L for factory made solid PVC panel type PVC door shutter 30mm thick consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rails, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent supplying and fixing in the frame at site as per specifications and drawing given under SSR Part II 2010 complete all as specified and directed. Make : SYNTEX/SHALIMAR/RAJSHRI

S&F 35 mm thick plain , framed ,panelled shutters ( any number of panels),in 2nd class hardwood,with panels of timber flat on both sides (feather edged) ,or of veenered particle board medium density, wood particle board with commercial face veneers supplied and fitted to chowkats complete all as specified.

S & F 35 mm thick glazed and skeleton shutters, in 2nd class hardwood, open rebated and prepared to receive glass, gauze etc, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24(a)

M& L for preparation of newly or previously untreated surfaces of wood or wood based surfaces of any description not other wise described , over10 cm width or girth and apply two coats of synthetic enamel paint over one coat of pink primer etc complete all as specified and directed.

M& L for preparation of old surfaces wood or wood based surfaces of any description not other wise described , over 10 cm width or girth and apply two coats of synthetic enamel paint over one coat of pink primer etc complete all as specified and directed.

S&F extruded aluminum alloy handles (150mm ) fabricated type anodised complete all as specified Make :- Shalimar / jyoti/ Classic/ Ashoka

S&F hinges (150 mm) stainless steel medium weight complete all as specified

S&F in repairs aluminum anodised barrel tower bolts (150 mm ) of extruded section complete all as specified

S&F in repairs 300 mm Aluminium alloy , anodised , sliding door bolt with hasp, staple (bolt type ) and fixing clips of sheet , cast , exctruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified

Dismantling floor, hearth or wall tiling including cement mortar, hedding removing serviceable tiles to store and rubbish off the premises all as specified and directed .

Dismantling boarding any description fixed in any position with nails complete all as specified and directed .

Dismantling wrought iron or mild steel work of any description

Dismantling of plain/corrugated steel sheeting, any gauge or thickness including Nainital or similar pattern roof covering.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and as directed.

M&L non skid coloured ceremic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, as in floors over screed bed or bedding layer of morar 15 mm in cement mortar 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and as directed.

Description all as per Serial item No 39 here-in-above but screed bed or bedding layer of morar 10 mm in cement mortar 1:4 on walls surfaces, such as skirting, to slab etc. complete all as specified and as dircted.

M&L for coloured Non-skid ceramic tiles 7 to 8mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floors etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 15mm thick cement mortar screed bed in CM 1:6 etc, complete all as specified and directed.

S& F coloured glazed ceramic tiles 350 x 250 x 7mm/450x350x7mm thick in dado/ skiting etc set and jointed in neat cement slurry and pointed in coloured cement to match, over and incl 10mm thick backing coat in CM 1:4 complete all as specified and directed .

M & L for machine cut cudappah stone slab as in window cills and jambs 20 mm thick to full thickness of wall fixed in steps over cement screed bed 20mm thick in CM 1:4 and jointed with grey cement paste and slurry including rubbing and polishing complete all as specified and directed

M&L for Kota stone slabs, 20mm to 25mm thick, machine cut as in flooring of size not less than 0.25 Square metre each, set and jointed in cement slurry and pointed in cement mixed with pigment to match the shade of slab laid over & including screed bed of 15 mm thick in cement mortar (1:4) including rubbing, cutting and polishing (mirror type), complete all as specified.

M&L for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing over and including 15mm thick cement mortar screed bed in CM 1:6 etc,complete all as specified.

M&L for acid resistant tiles 15mm thick vitreous ceramic, unglazed, set, jointed and pointed in chemical resistant mortar, resin type, in floors complete all as specified.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations over rendering 10 mm thick in CM 1:6 on brickwork or concrete surfaces complete all as specified and directed.

S&F in repairs 15mm bore bib taps cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified and as directed.

S&F in repairs 15mm bore stop valve cast copper alloy screwed high pressure with crutch or butterfly handle, screwed both end for iron pipe or for union complete all as specified & directed

S&F in repairs 15mm bore pillar taps,chromium plated, cast copper alloy screwed high pressure with crutch or butterfly handle, screwed both end for iron pipe or for union complete all as directed.

S & F in repairs 10 litres PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

S&F Swivel shower of PTMT any colour for fixing with 15mm pipe. (Minimum weight 40gms) in repairs complete all as specified and directed

M&L Grating doom 100mm dia of PTMT (Minimum weight 25gms) in repairs complete all as specified and as directed.

S & F PVC connections 15mm size with PTMT nuts of length 450mm

S&F cast iron Nahani trap 100mm dia out let including grating connecting jointing to waste pipe with lead jointing and taking out existing unserviceable traps by hacking out concrete joints and making good of surfaces complete all as specified and as directed .

Disconnecting following size of existing tanks, stacking safely for re-use (or lowering if required) and hoisting, reconnecting and refixing in position complete all as specified. (a) up to 1000 litres capacity.

M & L for APP modified roof treatment over existing roof slab etc including taking down to be executed through approved authorised applicator of the membrane manufacturer with the following specifications complete all as specified and directed:- (a) Applying oil bound bitumen primer @ 0.40 litre/ Sqm manufactured by the same manufacturer as that of APP with a density 0.87-0.89 Kg per litre at 25 degree centigrade on the prepared dry surface. (b) Laying APP modified water proofing membrane reinforced with non woven polyester fibre weight not less than 160gm/Sqcm using butane torch by torch application with 10cm side lap and 15cm end lap. (c) Physical properties of membrane shall be as under:- (i) Membrane weight not less than 3.50 Kg/Sqm. (ii) Non woven polyester weight not less than 160gm /sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 650N/Sqcm and transverse not less than 450 N/Sq cm (v) Tear strength-longitudinal not less than 300 N & transverse not less than 250 N. (vi) Elongation : > 20% in both directions. (vii) Impermeability/water tightness at 2 Kgf/cm2. (viii) Water absorption - Not more than 1% on mass within 24 hours. (ix) Cold flexibility - Minimum (-) 20C. (x) Dimentional stability % change = Maximum 1%. (d) Over the membrane provide a finishing with solar reflective bitumen aluminium paint @ 0.10 Kg/Sqm as prescibed by manufacturer.

S&F 18/19 mm thick prelaminated particle board both sides , interior grade , of approved shade and pattern fixid with screws to timber frame with beading piece for cupboard and shelves complete all as specified

S & F for continuous (piano) hinges, mild steel, bright finish or electrogalvanised width of flaps 30mm (when open) complete all as specified and directed.

S & F for 125mm aluminium handles, cast type, anodised complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and paving not exc 15 cm thick (above or below ground level) and removing the debris outside MD land complete all as specified

Plain Cement Concrete Type D2 1:4:8 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified

M&L 25 mm thick Cement concrete type B 2, 1:2:4 (using 20 mm graded crushed stone aggregate) in base of flooring complete all as specified

M& L for Chequered cement concrete tiles 20cm x 20 cm x 25 mm thick, set, jointed and pointed in near cement slurry in floors with mixture of grey cement and no pigment over screed bed or bedding layer of mortar 15 mm in cement mortar 1:6 complete all as specified and as directed.

S&F Miid steel (MS Angle Iron) as in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc Fe 410 -W (Gde- E- 250)quality-A complete all as specified and as directed.

M&L for Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

Supply and fixing hot dipped GI imposed grid with 24mm wide T sect exposed flanges powder coated frame work comprising of main runner made from 0.33 mm thick gs sheet of size 24mmx32mmx3000 mm @1200 mm C/C GI wire 4mm dia fixed by rawl plug, level adjusters and screws etc flush fitting of 1200mm long cross tee interlocked between main runners @ 600mm c/c to form 1200mmx600mm modules cross tee longer than 600 mm to be supported independently 600mmx600mm modules shall be formed by fitting 600mm long cross tee centrally between 1200mm cross tee ,perimeter wall angle shall be GS of size 19mmx19mm and 0.45 mm thick 300mm long including 600mmx600mmx8 to 10mm thick Armstrong gypsum reinforced board complete all as specified and directed.

S&F for Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed.

S&F for Ball bearing for rolling shutters complete all as specified and directed.

Excavation in trenches not exceeding 1.50 m wide and n.exc 1.5 m in depth for foundation of poles, cable etc, not exc 10 sqm on plan and getting out in soft/loose soil including taking out brick protection etc complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25cm thick complete all as specified and directed.

Removing excavated materials (soils) not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point complete all as specified and directed.

M & L for sand cushioning by spreading in trenches crushed sand by gently by punning down manually as in cable protection all as specified and as directed by Engineer -in-charge.

Supply and laying un-reinforced precast concrete cable cover class LV, type-I, flat size 250 mm x 150 mm x 40 mm laid in trenches all as specified.

Supply and Laying or fixing or passing through pipe, XLPE/PVC insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area 16 Sqmm 4 core including necessary connection and providing cable lugs as required all as specified.

M&L for reinforced cement concrete nominal mix M-20 (using 20mm graded stone aggregate) for foundations, including rafts, footings, foundation beams, plinth beams, bases for column etc and mass concrete, complete all as specified and directed. (Note - Reinforcement and form work will be measured and paid separately).

M & L for TMT bars of Fe-500 D grade conforming to IS: 1786, 12 mm dia & over, including cutting to length, bent to shape required, cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc, complete all as specified and directed.

M & L for TMT bars of Fe-500 D grade conforming to IS: 1786, 10 mm dia bars as in binders, spacers, strippus including cutting to length, bent to shape required, cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc, complete all as specified and directed.

M & L for use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams , side and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter, for rough finished surfaces of concrete, complete all as specified and directed.

Dismantling of old UNSV/rusted steel tubular poles 9 mtr long necessary disconnecting cables/over head condcutor and removing unserviceable pole from site complete all as specified and directed.

Supply, Fixing and connection of hot dip galvanised octagonal poles of height 6 mtr with 130mm bottom A/F & 70mm top A/F made up of 3mm thick HT sheet along with base plate of size 200 x 200 x 12mm thick including 4 nos of M20 x 600 long J type foundation bolts and 1 mtr long hot dip galvanised single arm standard bracket, including MCB of 6 Amps, with connector 4 way to be provided as termination point complete all as specified and directed.Make : BAJAJ/ ZENITH

Supply and fixing LED flood light 70 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and rosion resistant complete with driver and lamp in multiple optics including MS clamps,bolts, nuts, washers, anchor fastners etc complete all as specifed and as directed. Make : JAQUAR/ WIPRO

M&L for earthing using GI earthing strip 32 x 6mm complete with galvanised steel earth plate electode 600mmx600mmx6mm thick buried directly in ground, earth pit not less than 2.25 meters deep below ground level connection to and including GI strip of size 32x6mm to the extend 7.5 mtr as earth lead by means of GI bolts, Nuts etc. with provision of charcoal and salt all as per electrical plate No 3 of SSR Part I including water arrangement with GI Pipe 20 MM dia (medium Grade), earth lead protection pipe 50mm madium grade with bends, elbow etc. from earth plate to test point, excavation and earth work returning, filling, ramming and removing of soil to distance not exc 50mtr, make good to match with existing surface making PCC pit (Earth chamber) having internal size 30cm x 30cm x 30cm and outer size 60cm x 60cm x 60cm with RCC reinforced cover 50mm thick with one lifting handle made of 8mm dia MS bar funnel wie mesh and testing on completion including making test point on wall as per SSR specification all as specified and directed.

Taking down copper/ aluminum point wiring surface type, concealed type, flame proof type (Light/Fan/Socket or power) complete including fixtures and fittings such as switches, ceiling roses, pendants, regulators, socket, light fitting etc. Removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces to walls floors etc complete all as specified and directed.

M & L for point wiring with PVC insulated FRLS unsheathed 1100 Volts grade single core multistranded copper conductor cable 1.5 Sqmm drawn in and including PVC casing-caping and accessories, fixed on wall / ceiling etc with necessary fixing accessories and earth continuity conductor cable of 1.5 Sqmm size connected to common earth and earth dolly including 2 mm thick pressed steel terminal boxes concealed in wall covered with laminated sheet top cover 3 mm thick for mounting switches / sockets / fan regulators fixed with Cadmium plated machine screws all as specified for one light / fan / bell point controlled by one switch.

-Ditto- all as per item No 97.00 above but for one 5A 2pin/3pin socket out let multipurpose on the same board with other switches.

-Ditto- all as per item No 97.00 above but for one 5A 2pin/3pin switch socket out let multipurpose on independent Board.

All as per item No. 97.00 above but wiring complete with 2.5 Sqmm for 3 pin 15A socket multipurpose on independent board

S & F in replacement switch Piano, flush type, single pole, one way, 5 Amps, 230 Volts

S & F in replacement ceiling rose, surface bakelite, three terminals, AC, 230 Volts

S & F in replacement switch socket combination 2 in 1, 5 Amps, 5 pin multipurpose, flush type, 230 Volts

S & F in replacement switch socket combination 5 in 1, 15 Amps, 6 pin multipurpose, flush type, 230 Volts

S & F in replacement ceiling fan regulator electronic stepped type, AC, 230 Volts, flush type

S & F MCB DB, 4 way, TPN, double door, 415 Volts and including cutting chases in wall, concealing DB in wall, making good the disturbed surfaces and making all connections complete all as specified and directed.

S & F in replacement MCB DB 12 way SPN, double door, vertical type, IP - 43 with 200 Amps rated bus bar, AC and connecting up complete all as specified.

S & F in replacement MCB DB 8 way SPN, double door, vertical type, IP - 43 with 200 Amps rated bus bar, AC and connecting up complete all as specified.

S & F in replacement MCB DB 4 way SPN, double door, vertical type, IP - 43 with 200 Amps rated bus bar, AC and connecting up complete all as specified.

S & F MCB TPN 63 Amps, 415 Volts, 50 Hz, 16 KA Breaking capacity.

S & F MCB SPN 40 Amps, 240 / 415 Volts, 50 Hz, 10 KA Breaking capacity

S & F MCB SP 5 to 32 Amps, 240 / 415 Volts, 50 Hz, 10 KA Breaking capacity

S & F 20-22 W capacity surface/wall mounted LED batten having high efficiency long life LED chips with luminous efficacy of > 100 lumen/W, CCT 4000K to 6000K, independent isolated SMPS based constant current electronic LED driver with THD < 20%, CRI> 80, lamp burning hours not less than 50000, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, polycarbonate diffuser, housed in powder coated white extruded aluminium channel housing and white coloured ABS end caps having input voltage 220- 240 V, input frequency 50- 60 Hz, PF > 0.95, including electrical connection with 3 core flexible Cu conductor PVC insulated cable of appropriate size from ceiling rose to the fixture complete all as specified and directed.Make : BAJAJ/JAQUAR/WIPRO

S & F 10 W capacity surface/wall mounted LED batten having high efficiency long life LED chips with luminous efficacy of > 100 lumen/W, CCT 4000K to 6000K, independent isolated SMPS based constant current electronic LED driver with THD < 20%, CRI> 80, lamp burning hours not less than 50000, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, polycarbonate diffuser, housed in powder coated white extruded aluminium channel housing and white coloured ABS end caps having input voltage 220- 240 V, input frequency 50- 60 Hz, PF > 0.95, including electrical connection with 3 core flexible Cu conductor PVC insulated cable of appropriate size from ceiling rose to the fixture complete all as specified and directed.Make : BAJAJ/JAQUAR/WIPRO

S&F in Repairs 36 W LED recessed full lit luminaire with glare free uniform illumination with longer life and less maintainance 2x2 fitting mounted direct/indirect architectural luminaire including connecting 1.5 Sqmm white colour twin core copper wire suitable for false ceiling fixing arrangement all as specified and directed.

Supply and fixing LED street light fitting 30-35 Watt 230 V AC outdoor type with high pressure die cast aluminum housing along with prismatic polycarbonate optic with IP66 ingress protection having 4 kv in built surge protection with top opening driver cover for easy maintenance, efficacy not less than or equal to 100lm/W, CCT 5700K complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics including MS clamps,bolts, nuts, washers, anchor fastners etc suitable for fixing security light of Cat No -: ENXT P 35L WH PO PC SD of Bajaj or equivalent from philips/Jaguar/ wipro/ CG, complete all as specifed and as directed.

S & F GI steel tubing medium grade 40 mm dia and length up to 1.5 meter bent to shape of offset angle upto 45degree for fixing of security /street light fittings including MS clamps made of 32mm x5mm flat iron, nuts , bolts, etc all as directed by Engineer in charge

M&L for sub main wiring with two single core 4.0 Sqmm PVC insulated FRLS multistranded flexible copper conductor cable 1100 volts grade down in through non metalic PVC casing caping with and including PVC insulated 4.0 Sqmm single core single strand copper conductor as continous earth wire in green colour connected to common earth dolly all as specified and as directed. (Make :- PRESFIT/ PRECISION - Casing caping), (Make :- FINOLEX/ KEI/ BENLO/ POLYCAB - PVC Copper wire) Note : 1. Two runs of cable, one run of earth wire, one run of PVC casing capping of 4.0 sqmm will be measured and paid one unit.

M&L for sub main wiring with two single core 1.5 Sqmm PVC insulated FRLS multistranded flexible copper conductor cable 1100 volts grade down in through non metalic PVC casing caping with and including PVC insulated 1.5 Sqmm single core single strand copper conductor as continous earth wire in green colour connected to common earth dolly all as specified and as directed. (Make :- PRESFIT/ PRECISION - Casing caping), (Make :- FINOLEX/ KEI/ BENLO/ POLYCAB - PVC Copper wire) Note : 1. Two runs of cable, one run of earth wire, one run of PVC casing capping of 1.5 sqmm will be measured and paid one unit.

Taking down old unserviceable ceiling fan 1200 mm sweep by disconnecting the electric power supply, unscrewing the bolts and nuts, removing the blades and transporting to workshop to undertake repairs by rewinding of burnt out winding using suitable gauge copper wire, replalcement of worn out capacitor 2.5 mfd - 01 No., PVC canopy - 02 No's and bearing including scrapping of old paint and applying two coats of synthetic enamelled white paint over a coat of red oxide primer complete and refixing back at site complete all as directed.

Supply & fix Heavy Duty metallic Exhaust fan high speed type of sweep 300 mm, speed 1400 RPM, air delivery 1300CMH, power 70W (approx) comprising of double ball bearing, blades,louvers complete mounting anchor fasteners, aluminium louvers made of aluminium sheet of 0.5 mm thickness, provision of three core 1.5 Sqmm PVC insulated copper cable from ceiling rose to fan etc complete all as specified and directed. Make-:Crompton/ Orient/ Almonard/ Bajaj Note -: The Contractor shall submit 1 years warranty certificate from OEM of exhaust fan.

S&F single pole and neutral enclosure with a two pin and earth and metal clad plug socket complete with one single pole MCB 20 Amp 240 Volts complete all as specified including concealing in wall and directed.

Taking down carefully including water servicing of outdoor & indoor which including cleaning of cooling coils, tightning of loose terminations and refixing of same Window and split type AC 1.5/2.0 TR and connected items complete all as specified and directed.

Supply and fix copper tube of size 1/4" bore including brazing etc with rubberised insulation and tape suitable for supply pipes for air conditioners complete all as specified and directed.

Supply and fix copper tube of size 5/8" bore including brazing etc with rubberised insulation and tape suitable for supply pipes for air conditioners complete all as specified and directed.

Supply and fix PVC drain pipe of size 5/8" bore for supply pipes for air conditioners complete all as specified and directed.

Supply and fix 4 core 2.5 sqmm PVC insulated FRLS multistranded flexible copper conductor cable 660/1100 volts grade ISI marked complete all as specified and directed.

Supply and fix Heavy duty Water Proof Powder coated mounting bracket for installation of outdoor unit of air conditioner made out of 2 mm thick high grade steel with suitable fastener, MS nuts, bolts M8 x 45mm, washer, bolt M8 x 30mm nut, bolts & washers etc. duly painted complete set all as specified and directed. Make :- Companion Sleek, Aircool Sales Corporation or equillant make. Note : A sum of Rs 26,012.00 towards sch of credit shall be deducted to arrive the contract sum.

Parmatma Enterprises

Joy builders

AM ENTERPRISES

mp construction co

M/s Mukesh Engineers

Vishal Builders