Providing and fixing modular partition panel and supplying furniture for extension of administrative block at RTRM Hospital, Jaffarpur Kalan, New Delhi.

Amount

Providing and placing of panel & tile based modular workstations which are GRIHA compliant and as per BIFMA standards, with partition thickness of 50 mm thick including powder coated aluminium trims and supported on Legs for better air circulation and helps in keeping floor clean. The product should be complete and as per approved sample and as per the direction of Engineer-In-charge.

Panels Construction - Each panel consists of Vertical extrusions 2Nos and Horizontal extrusions made of 1.2mm thick aluminium with duly powder coated at every division of tile/block. Each panel have Bottom frame fabricated for 52.4mm panel comprises of L-channels made of 2mm thick CRCA steel (IS: 513), formed plates of 3mm thick HR steel (IS: 2062) & ERW steel tube of size 35x15x1.6mm thick in oval cross section (IS: 7138) welded together. The complete bottom frame shall be powder coated with an average of 50-60 microns thickness of epoxy powder coating. The Bottom Frame is bolted with the Upright verticals. Each Panel is provided with 2Nos Legs of height 120mm are fixed at the bottom frame of the panel. Legs are fabricated by CO2 welded MS Tube of section 38mm x 25mm (IS: 7138 ERW Tube, 38mm x 25mm x 16bg) with the base plate of the MS plate of 35x22x5mm (IS: 2062, 5mm HR) over which an M8 Leveler is fitted which allows for adjustment of the height by 50mm. It will be coated with 45-50micron thickness of epoxy powder coating. Each Panel consists of 2Nos Intermediate blocks. In a 52.4mm Thick panel intermediate block shall comprise of 38mm thick paper honeycomb with 3mm MDF on each sides and 0.6mm decorative laminate on both sides. Particle board framing shall be used in outer boundary of these blocks as well as intermediately at certain locations forming conduit for passing cables. These blocks will be located in the middle bands of the panels made out of a composite construction of MDF and paper honeycomb. Each Panel consist of TOP TILES/SPLIT TILES. These tiles shall be slide in to the panels from top before fixing the top horizontal. These tiles shall be supported from top & bottom side with clips made from PP co polymer fitted in horizontal extrusion. In case of split tiles it shall be offered in Fabric magnetic tiles, Whiteboard tiles. Each Panel consists a BOTTOM TILE. These bottom tiles shall be press fitted on to the assembly frame of the panel with the help of snap on clips made of nylon-66 and support clips made from PP polymer. All partitions and side panels have levelling screws for adjustment in case of Uneven floor to take care of +/- 40 mm of uneven flooring.

Tile Finishes : a FABRIC MAGNETIC TILES: Fabric magnetic tiles shall be fabric upholstered metal tiles in 0.6 mm thick G.I. Grade O as per IS: 277. The fabrics shall be upholstered with adhesives. • FABRIC TACK TILES: Fabric tackable tiles shall be upholstered metal tiles in 0.6mm thick G.I. grade O as per IS: 277, with P.E. foam in the tile for tackablity. The fabric shall be upholstered with adhesives. • WHITE BOARD TILES : White board tiles shall be made of 8.0 mm thick particle board conforming to IS: 12823 laminated with 0.6mm thick white glossy high pressure laminate on outer side & 0.6mm backing laminate on inner surface and will be having all its edges with minimum 0.5 mm thick PVC edging.

End/Intermediate Panels : It is a 22.8mm Thick panel used at the ends and as a intermediate panel between 2 adjacent workstations. It is connected to the main panel using screws and provided with trims on the outer edges.

Aluminium Trims : The top trims and end trims for 52.4 mm shall be made from aluminum extrusion. All kinds of extrusions for 52.4mm shall have average wall thickness of 1.2 mm & having finish of powder coating. Top trim in 52.4mm thick panel shall be press fitted on the horizontal extrusion, it shall be slide fitted with the help of top trim connector made from PP copolymer 3530 grade.End trim for 52.4mm thick panel shall be slide fitted with the help of end trim connector made from 2.0mm thick M.S. CRCA Grade D as per IS: 513. End trim for 22.8 mm thick panel shall slide with the help of end trim connector made from nylon-66.

Wire Management - Wires shall be taken into the system through cable ducts from the junction boxes and it is carried upto the panels through concealed conduits inside the blocks. Wires runs through the system from Bottom tile and extended to the top at various locations by the help of 2 nos. vertical Cable Ducts in each panels. Cable duct shall be made from 0.8 mm thick M.S. CRCA Grade D as per IS: 513 - 1994. It is constructed with two parts, one is body & another is cover. It holds the cables & gives aesthetic appearance by covering all cables entry, which are moving upward to the panels. Size of Cable duct is 107mm W X 154 mm H X 21 mm D.

Legs - Metal powder coated legs at the end. System shall also have 120 mm high powder coated standalone panel legs to give the system an elevated look. Single side legs are fabricated by CO2 welded MS Tube of section 38 mm x 25 mm (IS: 7138 ERW Tube, 38 mm x 25 mm x 16bg) with the base plate of the MS plate of 35x22x5mm (IS: 2062, 5 mm HR) over which an M8 Leveler is fitted

Worksurface : Worktop shall be made out of 25mm thick prelaminated particle board. All the open edges of work surface shall be provided with machine pressed 2 mm thick PVC lipping glued with hot melt EVA glue. The work surface shall be provided with circular cut out of Dia.65mm as per the requirement, for passing of wires. These cut outs shall be provided with ABS covers. Worksurfaces are fitted to the panels by worksurface brackets. Brackets are made of 2.0mm thick CRCA grade D steel as per IS : 513. Brackets are slide in between end trim and vertical extrusions.

Mobile Drawer : Mobile Drawer Unit having 3 Drawers Unit having flat metal front and top with Central locking. The Drawer Unit consistes of 2Box and 1File Drawers. The Overall size of the Drawer Units is 450mm(W) X 435mm(D) X 646mm(H). Construction & Material of Drawer Unit : Welded Assembled of 0.8 thick CRCA for Body Shell, Drawer Front & tray, Front Side Stiffener, Rear Side Stiffener & Bottom, 1.2 thick CRCA Top Stiffener & Bottom stiffener. Drawer Fronts & Metal Front Straight Edge. All Drawers with Double extension precision ball slide shall be provided. For Drawer pulling, side wise tapered recess provided in shell behind Drawer Fronts. Locking:10 lever Cam Lock & Central Right Hand locking with actuator & lock channel mechanism. Top Panel : 0.8 Thick Metal Straight Edge Top. Castors : Swiveling non-lockable 4Nos Castors mounted below the body shell. The Total drawer unit is finished with Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10).

Key Board Pullout Tray : Supplying and Fixing of sliding computer key board tray of 480mm (L) X 280mm (D) X 40mm(H) made out of CRCA steel as per IS : 513 made of 0.9mm thick powder coated with sliding channels and other fixing fittings. It should also have a sliding system for accommodating mouse.

CPU Trolley : Supplying and Fixing of CPU Trolley of Size - 345mm(W) x 226(D) x 180mm(H) is made of 1.0 mm thick MS CRCA Sheet and Side support is made of 0.8 mm thick MS CRCA Sheet. It consists of 4Nos Non-lockable twin wheel castors made of injection moulded in Black Nylon.

Recta - 1200 W x 600 D x 1500 H

Providing and Fixing in position Medium Back Chair. The seat shall be made up of 1.2+/-0.1cm thick hot pressed plywood measured and upholstered with fabric or synthetic leather and moulded polyurethane foam. The back shall be made up 1.2+/-0.1cm thick hot pressed plywood upholstered with replaceable fabric or synthetic leather upholstery covers and moulded polyurethane foam. The back ply and foam is designed with contoured lumbar support for comfortable seating posture. The moulded polyurethane foam shall be of density 45+/-2kg/m ³, and hardness load 16+/-2kgf as per IS:7888 for 25% compression. The dimensions of seat shall be- 51.0cm(W) x 48.0cm(D) and of back shall be 48.0cm(W) x 64.5Cm(H). The armrest top shall be made of moulded polyurethane and mounted on to a drop lift height adjustable type M.S tubular armrest support chrome plated. The armrest height shall be adjustable up to 6.5+/-0.5cm in 5 steps and also has swivel adjustment of 22 degree+/-2 on both sides. The mechanism of the chair shall have following features : 360⁰ revolving type, Knee tilt synchro mechanism, Tilt tension adjustment, Single point control, 4 position locking with anti shock feature, Seat/Back tilting ratio of 1:2. Seat depth adjustment of 6.0+/-0.5cm should be locked in 6 positions. The backrest shall consists of a sliding up down mechanism, Which can be adjusted in the range of 7.5+/-0.5cm and should be locked in 4 positions for correct position of lumber support. The chair shall be provided with pneumatic height adjustment which shall have stroke of 9.0 +/- 0.3 cm. The pedestial shall be fabricated from 0.2+/-0.02cm thick HR sheet, chrome plated and assembled with injection moulded black polypropylene hub cap. The size of the pedestal shall be 66.0+/- 0.5 cm pitch-centre-dia (76.0 +/- 1.0 cm with castors). The twin wheel castors shall be made black nylon. Overall dimensions of Chair shall be, Width of Chair - 76.0cm, Depth of Chair - 76.0cm as measured from pedestal below. Height from ground - min 89.0 to max 105.0cm. Seat height - min 46.9 to max 55.9 cm.

Providing and Fixing in position Plain Storwel. Overall size of Storwel shall be 916 mm (W) x 486 mm (D) x 1980 mm (H) with welded construction. It shall have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength. The Storwel Plain shall have a Mazak handle and Three way locking mechanism with Shooting Bolts. It shall have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It shall have 4 no.s full shelves. A4 size box file(85 W x 285 D x 345 H mm) can be stored vertically on three shelves and the clear space above fourth shelf is 240mm. It shall also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available. There shall be 5 loading levels in storewel plain.

Providing and Fixing in position Low Height Storwel. Overall size of the storwel shall be 916 mm (W) x 486 mm (D) x 720 mm (H) with welded construction. It shall have the shelf thickness of 0.6mm(+/-0.07mm), Back thickness of 0.8mm(+/-0.08mm) and all other components shall be 0.9mm(+/-0.08mm) thick. These components are made of CRCA ‘D’grade high yield strength as per IS:513. The Minor Plain shall have a Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting (3 nos.) which shall have a Uniformly Distributed Load capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10).The loading levels shall be 4.

Providing and Fixing in position 22 Seater Modular Conference Table. Overall size of the table shall be 6600 L mm x 1800 W mm x 750 H mm. Top shall be made of 36mm thick MDF one side prelaminate board with 0.4mm PVC membrane pressed on to top and shall have chamfered edge. Plastic ABS access flap shall be provided for easy access to wires and cables. The Understructure shall be made of mixture of 25mm and 18mm Pre-laminated twin board of E1-P2 grade, Edge banded with matching 2 mm thick PVC lipping. Aluminium alloy 63400 - WP profile shall be used for connecting panels together. Modesty Panel shall be made of 18mm Thick Pre-laminated twin board of E1-P2 grade, Edge banded with matching 2 mm thick PVC lipping. Powder coated accent metal strip shall be provided below work surface to enhance aesthetics. It shall be made of 0.8mm CRCA as per IS 513, & shall be epoxy polyester powder coated (DFT 40-60 microns). Wire Management shall be an array of panels made of 0.8mm CRCA MS IS:513, & shall be epoxy polyester powder coated (DFT 40-60 microns) shall be used for flow of wires and cables. Provision to mount 6 module switch plate shall be provided below worktop. Cutout on top with two piece injection moulded plastic part polymer component shall be fitted to pullout audio,video cables onto worktop and connect devices charger to power socket below worktop.

Providing and Fixing in position High Back Chair. The seat shall be made up of 1.2+/-0.1cm thick hot pressed plywood and upholstered with fabric or synthetic leather and moulded polyurethane foam. The back shall be made up 1.2+/-0.1cm thick hot pressed plywood upholstered with replaceable fabric or synthetic leather upholstery covers and moulded polyurethane foam. The moulded HR polyurethane foam shall be of density 45+/-2kg/m ³, and hardness load 16+/-2kgf as per IS:7888 for 25% compression. The dimensions of seat shall be- 51.0cm(W) x 48.0cm(D) and of back shall be 48.0cm(W) x 76.0Cm(H). The armrest top shall be made of moulded polyurethane and mounted on to a fixed type M.S tubular armrest support chrome plated. The Arm support has static vertical adjustment of +/-1.5+/-0.05cm. The mechanism of the chair shall have following features : 360⁰ revolving type, Front pivot synchro mechanism, Tilt tension adjustment, Single point control, 4 position locking with anti shock feature, Seat/Back tilting ratio of 1:2. The backrest shall consist of a fixed type mechanism i.e no back up/down adjustment. The chair shall be provided with pneumatic height adjustment which shall have stroke of 9.0 +/- 0.3 cm. The pedestial shall be fabricated from 0.2+/-0.02cm thick HR sheet, chrome plated and assembled with injection moulded black polypropylene hub cap and 5 no.s twin wheel castor. The size of the pedestal shall be 66.0+/- 0.5 cm pitch-centre-dia (76.0 +/- 1.0 cm with castors). The twin wheel castors shall be made black nylon. Overall dimensions of Chair shall be, Width of Chair - 76.0cm, Depth of Chair - 76.0cm as measured from pedestal below. Height from ground - min 102.5 to max 111.5cm. Seat height - min 46.0 to max 55.0cm.

Providing and Fixing in position Reading Table. Overall size of the table shall be 1800 W mm x 900 D mm x 740 H mm. The top shall be made of 25 mm thick PLB with 2 mm thick PVC Edge Beading plus the Understructure shall be having C - Frames 1.6 mm thick MS supporting the top. The Legs shall be of dia. 38.1 x 1.6 mm thick MS ERW tube .

Providing and Fixing in position 4 Door Book Case. Overall size of the case shall be 914 mm (W) x 320 mm (D) x 1742 mm (H). The unique design provides the right rigidity to the Top hinged doors , which shall facilitate easy use. The Book Case shall be made from prime quality CRCA steel with anti rusting treatment. It shall have a Rigid Knock Down Construction. The Top Pannel, Back Pannel and Side Pannel are made from 0.7mm high yield CRCA and other components from 0.8mm CRCA. Each door shall have a 6 Lever Cam Lock with Common Key. 3mm thick glass should be used in each door for clear inside vision whih shall be secured in a metal frame through a rubber gasket. Scissor Mechanism should be provided in each door for receding inside the top of every compartment and it shall ensure parallel and smooth movement. Each door should be provided with plastic side end caps as handle which is easy to grip. Each compartment shall have a storage shelf with a UDL capacity of max 80 Kg. The 4 Door Book Case shall have metal inside top panel. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10).

Providing and Fixing in position 12 Door Personal Locker Unit. Overall size of the Locker Unit shall be Overall size of the locker unit shall be 760 mm (W) x 450 mm (D) x 1830 mm (H). The unit shall be provided with 6 No.s of Lockers in a unit. Locking shall have 10 Lever cam lock with lock lever plus option of hasp arrangement . Material shall be CRCA 0.6 mm thickness . Construction shall be Rigid Knockdown construction , shelf shall be uniformly distributed load capacity per each shelf level is 35 Kg maximum . Finish shall be epoxy polyester powder coated to the thickness of 50 microns . Handle/Label holder shall be Aesthetically appealing Snap fit ABS plastic handle . Ventilation shall be attractive punched pattern for ventilation. Overall size of each locker shall be 375 W mm x 411 D mm x 285.1 H mm.

Providing and Fiixing in position Storage Unit. Overall size of the Storage unit shall be 1650 W mm x 500 D mm x 18000 H mm. The top panel shall be made of 25 mm thick MDF one side pre-laminate board with 0.4mm PVC membrane pressed on to top. The slide door unit shall be made of 25 mm Thick Pre-laminated twin board of E1-P2 grade and approved shade ,Edge banded with matching 2 mm thick PVC lipping for body panels like side, bottom, back and shelves. The shutters shall be made of 25 mm thick MDF one side pre-laminated board with 0.4mm PVC membrane pressed on to top. Shutters shall have a soft - closing & anti-slam mechanism. Handles shall be provided for ease of opening. Storage shall be provided with lock for security.

Providing and Fixing in position Visitors Chair. The seat shall be made up of 1.2+/-0.1cm thick hot pressed plywood and upholstered with fabric or synthetic leather and moulded polyurethane foam. The back shall be made up 1.2+/-0.1cm thick hot pressed plywood upholstered with replaceable fabric or synthetic leather upholstery covers and moulded polyurethane foam. The back ply and foam is designed with contoured lumbar support for comfortable seating posture. The moulded polyurethane foam shall be of density 45+/-2kg/m ³, and hardness load 16+/-2kgf as per IS:7888 for 25% compression. The dimensions of seat shall be- 51.0cm(W) x 48.0cm(D) and of back shall be 48.0cm(W) x 64.5Cm(H). The armrest top shall be made of moulded polyurethane and mounted on to a fixed type M.S tubular armrest support chrome plated. The Arm support has static vertical adjustment of +/-1.5+/-0.05cm. The backrest shall consist of a fixed type mechanism i.e no back up/down adjustment. The leg frame welded assembly shall be chrome plated, made from 3.5+/-0.03cm x 1.5+/-0.02cm x 0.16+/-0.0128cm thick ellipitical MSERW tube and provided with a base plate for seat fixing. Overall dimensions of Chair shall be, Width of Chair - 66.5cm, Depth of Chair - 58.0cm as measured from pedestal below. Height from ground - 88.5cm. Seat height - 45.0cm.

Providing and Placing in position 2 seater sofa. Upperstructure shall be a single shell 1.2 ±0.1cm. thick hot pressed plywood. Dia 4mm zig-zag type assembly is mounted in the understructure for support and additional cushioning purpose. The seat is made up of PU foam with density 32+/-2 Kg/m3 having an additional top layer of PU foam with density 28+/-2 Kg/m3, upholstered with fabric or leatherette. The back is made up of 28+/-2 Kg/m3 with additional top layer of PU foam with density 23+/-2 Kg/m3, upholstered with fabric or leatherette. The leg is a welded assembly made up of stainless steel (grade SS 202) tube and plate. Overall Dimensions of Chair shall be Seat Height - 45.0 cm, Height - 82.0cm, Width & Depth of Chair as measured from pedestal - Width-146.0 cm and Depth-92.0 cm.

Modern Office Systems

M/S DURIAN INDUSTRIES LIMITED

K.K. Construction Company