Spl repair of Offrs single living Accn bldg. No P-36 and Spl repair to bldg. No P-26 in Md Accn 550 Acres under GE (East) Ferozepur Cantt

Amount

Dismantling floor, hearth or wall tiling including cement mortar beding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

S&F non skid coloured ceramic tiles 7 to 8 mm thick (Square/Rectangular) area of each tile exe 0.11 Sqm but not exe 0.18 Sqm in floors etc set and jointed in neat cement slurry and pointed with white cement mixed with pigment to match with colour of tiles over and incl screed bedding 15mm thick in cm(1:4), complete all as specified and directed.

M & L Glazed Ceramic coloured tiles in vertical surface 350 x 250 x 7mm/450 x 300 x 7 mm thick premium quality over and incl 10 mm thick rendering in CM 1:4 on vertical surfaces, set and jointed in neat cement slurry and pointed with white cement mixed with pigment to match colour of tiles complete all as specified & directed.

M & L Vitrified tiles 8-9 mm thick (Square/rectangular) polished, light shade, area of each tile not exe 0.36 Sqm, in flooring etc set and jointed in neat cement slurry and pointed with white cement mixed with pigment to match with colour of tiles over and incl screed bedding 15mm thick in cm(1:6), complete all as specified and directed.

All as per item No 4 here-in-before but as in skirting over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M & L chequered cement concrete tiles 20 Cm x 20 Cm x 25 mm thick, set, jointed and pointed in neat cement slurry in floors mixed with pigment to match with colour of tiles over and incl screed bedding 20 mm thick in cm(1:6), complete all as specified and directed.

M&L machine cut prepolished kota stone flooring 18-20 mm thick over & including 20mm thick screed bed in cement mortar 1:6, laid jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing, complete all as specified and directed.

M&L machine cut prepolished kota stone 16-18 mm thick as in risers of steps, skirting, dado etc over & including 15mm thick rendering in CM 1:6, jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing complete all as specified and directed.

Taking down cement plaster from brick walls of any description, racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M & L Rendering/plastering, 15mm thick in cement mortar (1:4) on any face of brick walls or concrete surfaces finished even and fair complete all as specified and directed.

M & L Rendering/plastering, 12 mm thick in cement mortar (1:6) on any face of brick walls or concrete surfaces finished even and fair complete all as specified and directed.

M & L Rendering/plastering, 5mm thick in cement mortar (1:3) on concrete surfaces, finished even and fair as in ceiling complete all as specified and directed.

M&L for applying two coats of Cement base paint over a coat of primer on newly plastered surfaces of walls including preparation of surfaces complete all as specified and directed.

M & L for applying three coats of White wash on newly plastered surfaces of ceiling including preparation of surfaces complete all as specified and directed.

M & L for applying three coats of White wash on newly plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

M&L for applying two coats of oil bound distemper over 2 mm thick wall care putty of new plastered wall surfaces of wall including preparation of surfaces complete all as specified and directed.

M & L for applying two coat of Oil Bound distemper over 2 mm thick wall care putty on old surfaces of wall including preparation of surface complete all as specified and directed.

M & L for applying two coat of white wash over old surface of walls including preparation of surfaces complete all as specified and directed.

M & L for applying two coats of white wash on old Ceiling surface including preparation of surface complete all as specified and directed.

M & L for applying two coat of Cement base paint over old surface of walls including preparation of surfaces complete all as specified and directed.

S&F 18mm thick Celuka plywood of grade 1 qualiity, one side pre lamination plain and other side plain white colour fixed with screws , solvent cement/adhesive to make cupboard shutters/ shelves including Dismantling of boarding, any description, fixed in any position with nails complete all as specified and directed.

S & F Continous (piano) hinges of mild steel bright finish or electro galvanised with flap (when open) 30mm,fixed with steel screw complete all as specified and directed.

S&F in repair 100mm long hasp and staple, safety type, aluminium anodised including bolt to hinge plate and fixed with screws and fixed complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size not exc 1.50 Sqm each including cutting holes of appropriate size for insertion blocks of cement concrete for hold fasts complete all as specified and directed.

All as per item No 24 here-in-before but size exceeding 1.5 Sqm & not exceeding 4 Sqm each. complete all as specified and directed.

M & L Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

M & L solid panel PVC door shutters 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement and fixed in the frame at site complete all as specified in clause 8 B.2.1 of MES schedule Part-II (2004).

S&F Aluminium powder coated (minimum thickness of powder coating 50 micron) as in frame for doors, windows, ventilators with one or more rebates including joining cleats/aluminium beading for fixing etc. complete all as specified and directed.

S & F Aluminium powder coated (minimum thickness of powder coating 50 micron) for shutters of doors, window and ventilator including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (fiitings shall be paid for seperately) with extruded built up standard tubular sectios/appropriate Z section and other section of approved make conforming to IS:733 and IS:1285, fixing with dash dasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc aluminium section shall be smooth, rust free, straight, mitred and joined mechanically whenever required including cleat angle, aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screw all complete as per architectural drawing and the direction of Engr-in-chief. Anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (2 no.) . Note:- (i) Aluminium chowkhat /frame, glass,wiremess shall be measured and paid separately.

S&F Anodised aluminium powder coated window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 1.30 kg/m including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable tower bolt (02 no) handle (1no.) in each leaf complete all as specified. Note:- (i) Aluminium chowkhat /frame, glass,wiremess and aluminium grill shall be measured and paid separately.

S & F 4 mm thick ACP sheet for Aluminium door including rubber gasket, Aluminium bidding/stirrups complete all as specified and directed,

S & F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor overall length of cover plate 140 mm, complete all as specified and directed

S & F door closer hydraulically regulated designation No .03, universal type, suitable for door shutters of 851 to 1000 mm in width and off weight between 61 to 80 Kg and fixed aluminum (extruded section) complete all as specified and directed.

S&F Mortice lock,vertical type,size 100mm (04 lever) including necessary fittings complete all as specified and directed.

S & F Figured glass, 3mm thick, pin headed type and glazing with oil putty in squares not exceeding 0.50 square metre each pane complete all as specified and directed.

S&F 4.8 mm thick sheet glass ordinary quality and glazing fixing with rubber beads with solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers in windows/ventilators in square n. exc 0.5 Sqm in each pane complete all as specified and as directed.

S & F stainless steel Wire cloth galvanised mild steel, 0.56mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staples complete all as specified and directed.

S & F Framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

Preparation of old treated steel surfaces of any description, over 10cm width or girth and applying one coats of synthetic enamel paint complete all as specified and directed.

Preparation of old treated wooden surfaces of any description, over 10cm width or girth and applying one coats of synthetic enamel paint complete all as specified and directed.

S&F Aluminium Anodised handles 150 mm long fixed to doors/windows complete all as specified and directed.

S&F Aluminium Anodised tower bolts 200 mm long fixed to doors/windows complete all as specified and directed.

S & F Aluminium Anodised butt hinges, type C21, 125 mm long, fixed with galvanised mild steel hinge pin complete all as specified and directed.

S & F Water storage tanks 500 liters capacity rotational moulded, triple layer polythene (cyindrical vertical with closed top) hoisting and fixed in position on roofs including dismantling existing water storage tank complete all as specified and directed.

S&F Ball valve of PTMT 20mm bore, high pressure with polythene float and fly nut complete with aluminium rod, screwed for iron pipe or brass ferrule and fixed, complete all as specified and directed.

S & F CI Gate valve, 20mm bore, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union fixed in repairs complete all as specified and directed.

S & F CI Gate valve, 15mm bore, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union fixed in repairs complete all as specified and directed.

S & F 16 mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings fixed complete to walls and ceilings or laid in floors including fitting like elbow, reducer, tee, union, nipple etc incl taking up or down existing steel water tubing, 15mm bore alongwith connections fixed/laid in any situation, complete all as specified and directed.

All as per item above 48 herein before but 20 mm bore tubing. complete all as specified and directed.

S&F Stop valve of cast copper alloy chromium plated fancy type, 15mm bore, screwed down, high pressure with crutch or butter fly handle, fixed in repair complete all as specified and directed.

Ditto as above item 50 but fancy type, chromium plated with long shank and cup (concelled type), complete all as specified and directed.

S & F in repair Bib tap fancy type, cast copper alloy chromium plated, 15mm bore, with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F central hole basin mixer for wash hand basin including all fittings ie including connection pipe as per manufactures specification complete all as specified and directed.( Make Parko/ESSCO/Prayag.

S & F Wall mixture 3 in 1 with provision of overhead shower complete with 115 mm long bend pipe on upper side, connecting legs and wall flange complete all as per manufactures instruction and as directed. (Make Parko/ESSCO/Prayag.

S & F single piece WC of size 365x655x765 with flushing cistern and connection pipe P or S trap (Closed pattern incl all necessary accessories like rag bolts, kit/gel gasket etc (including flushing cistern, pvc seat cover, jet, health faucet and flush pipe complete all as specified and directed. Make :- cera, Parryware, somani

M & L for vitreous china shape wash basin white with pedastal type, flat back, size 560x470 mm including 32 mm dia CP waste coupling and waste pipe and pvc connection pipe complete all as specified and directed.

S & F Swivel shower of CP, size 150 x 150 mm any colour including shower arm for fixing with 15mm pipe complete all as specified and directed.

S & F Shelf of Brass chromium plated fixed with & including CP brass screws & wooden/Plastic cleats (min. weight 300 gms) complete all as specified and directed.

S&F tubular towel rail, 20mm dia of 600mm long with fancy type brass chromium plated brackets on both sides and fixed with steel screws and wooden/rawl plugs, complete all as specified and directed.

Dismantling CI pipe/any type alongwith fittings of 75/100mm dia, below or above ground level, jointed in cement mortar and taking out complete all as specified and directed.

S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches complete all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches complete all as spd and directed.

PVC (SWR) bend (any radius), 110mm bore, diminishing pieces or tapers (larger bore measured) jointed in cement mortar complete all as specified and directed.

All as per item 64 above here-in-before but 75mm bore, complete all as specified and directed.

PVC (SWR), floor trap, 75mm bore, Plain with grating including jointing with solvent cement complete all as specified and directed.

S & F PVC (SWR) junction single/double, (single/double T) or equal or unequal 110 mm complete all as specified and directed.

S&F PVC rain water pipes 110mm bore including fixing to walls with MS clamps complete all as specified and directed.

Dismantling brick tiles laid in single layer jointed & pointed in cement mortar complete all as specified and directed.

Demolition of mud phuska in roofs, any thickness, including leeping plaster (whether full thickness removed or only a part thereof) complete all as specified and directed.

M&L for Cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in roof padding complete all as specified and directed.

M & L 10mm plaster in CM(1:4) finished even and smooth without using extra cement on bottom layer of batten roof with water proofing compound (in case of re placement of bottom layer tile)complete all as specified and directed. (WPC shall be measured separately)

M&L for water proofing treatment to roof surface including parapet wall comprising with the following course of treatment/ specifications form bottom to top:- (a) Applying evenly a tack coat of industrial bitumen 85/25 @ 1.2 kg per sqm over a coat of bitumen primer @ 0.30 ltr per sqm including preparation of roof surfaces complete all as specified and as directed. (b) One layer of APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified. Polymeric membrane shall be taken to a height of 60 cm (minimum) and then inserted inside the groove of parapet walls and shall be finished by a membrane flashing. Note: (i) Laying of APP based membranes shall be done by torch on method or as per manufacturer's instructions. (ii) A minimum overlap shall be 75mm length wise and 100 mm width wise of polymeric membranes respectively and sealed all overlaps and joints as manufacturer's instructions.

M&L for two coat of aluminium paint over APP membrane complete all as specified and directed.

Demolition of brick work built in cement mortar of any specification and in any position complete all as specified and directed.

M&L for Brick work in cement mortar 1:6 using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6 metre mean radius complete all as specified and directed.

M&L All as per item 76 above here-in-before but using old bricks retrieved from demolition under item no 75 above here-in-before including cleaning and removal of mortar from old bricks complete all as specified and directed.

M&L Brick work in cement mortar 1:4 using sub class ‘B’ old size bricks, straight or curved on plan to any radius in half brick thick walls complete all as specified and directed.

Demolition of un-reinforced cement concrete below or above ground floor and paving not exceeding 15 cm thick (below or above ground level) complete all as specified and directed.

Cement concrete (1:2:4), type B-0 using 12.5mm graded stone aggregate as in benching, kerbs, mud stop, rounded or chamfered on edges including form work complete all as specified and directed.

M&L for laying APP based polymeric membrane 3mm thick with minimum weight not less than 3 kg/sqm, reinforced with non woven polyster fabric (wt not less than 160 gms/sqm) torching Joints/overlaps with a propane or a butane gas torch,laid with a minimum overlap of 150mm with thermo fusable finish laid/bonded over a coat of hot blown bitumen 85/[email protected]/sqm,over forced application bitumen primer @0.30 litres per sqm,including preparation of plastered surfaces of Sunken portion ,complete all as specified and as directed.

M & L rendering 10mm plaster in CM(1:3) finished even and smooth with using extra cement on vertical surface of sunken portion wall and floor with water proofing compound (in case of re placement of bottom layer tile) complete all as specified and directed. (WPC shall be measured separately)

S&F GI pipe 40 mm bore medium grade including fixing to walls as in spouts of sunken portion complete all as specified and directed.

M & L Cement concrete (1:5:10),type E-2 using 40mm graded stone aggregate in foundation filling and mass concrete complete all as specified and directed.

Mild steel curtain rod CP powder coated with fixing side brackets, end cups, pinion, rings @ 10 Nos per running metre and fixed with PVC rawl plugs & steel screws as in repairs complete all as specified and directed.

M & L for PCC (1:3:6) type C2 (20mm graded stone aggregate) 50mm thick as in plinth protection and the same filled with bitumen mastic (01 Part of bitumen and 03 Part of sand) complete all as specified and as directed.

M & L for formwork to chullah, hooks, chajjas, troughs and similar work including edges complete all as specified and directed.

M & L for reinforced cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in chajja, supported on walls, beams, roofs, landing, bolconies, canopies and in shelves and like complete all as specified and directed.

M & L for mild steel 10 mm dia and over TMT bars as in reinforcement cut to length bend to shape required including cranking, hooking at ends and binding with mild steel wire, (anneled) not less than 0.5 mm dia complete all as specified and directed.

M & L for mild steel 08 mm dia and over TMT bars as in reinforcement cut to length bend to shape required including cranking, hooking at ends and binding with mild steel wire, (anneled) not less than 0.5 mm dia complete all as specified and directed.

M & L for repairing the edges of concrete chajjas, facias, column & the like by providing PCC (1:2:4) type B-0 including all necessary formwork and/ or provision of rendering 15 mm thick (average thickness) in cement mortar (1:3) with chiken wire mesh, after applying a coat of cement slurry @ 3 Kg/Sqm of surface finished even and fair, surface area not execeeding 600 mm wide, in patches including taking down swoolen/damaged plaster or concrete complete all as spcified and directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons laid ,beded and pointed in any morter complete all as specified and directed.

M&L for Green marble work 18 to 20 mm thick ( table rubbed and polished) one piece as in stairs landing ,risers of steps,jambs,pillars, window cills cooking platforms etc , jointed with white cement (1:2) using marble dust with admixture of pigment to match with marble shade including 10mm thick rendering in CM 1:4 etc complete all as specdified and directed.

M&L cement concrete type D2 (1:4:8) (using 40 mm graded stone aggregate ) as in foundations, filling and mass concrete complete all as specified and directed.

M&L PCC 75 mm thick (1:2:4) type B-1 (using 20 mm graded stone aggregate ) as in base for pavings laid in alternative bays including glass dividing strips 3mm thick etc complete all as specified and directed.

S&F non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in flooring etc set and jointed in neat cement slurry and pointed with white cement mixed with pigment to match with colour of tiles over and incl screed bedding 15mm thick in cm(1:6), complete all as specified and directed.

S&F for Joint less non skid ceramic tiles8-9mm thick (square/rectangular) polished dark shade, area of each tile exceeding0.18 but n exc 0.38 sqm in flooring etc set and jointed in neat cement slurry and pointed with white cement mixed with pigment to match with colour of tiles over and incl screed bedding 15mm thick in cm(1:6), complete all as specified and directed.

M&L for wall/ roof projections including facia, cornices etc by scrapping and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over 2mm thick cement base putty and sanding the surface to prepare the surface even and smooth complete all as specified and directed at any height incuding necessary scaffolding complete all as specified and directed.

M&L for complete removal of existing treatment on wall/ roof projections including facia, cornices etc by scrapping and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over 2mm thick cement base putty and sanding the surface to prepare the surface even and smooth complete all as specified and directed at any height incuding necessary scaffolding over new/complete removal surfaces.

M&L for applying two coats of oil bound distemper of new plastered wall surfaces of wall including preparation of surfaces complete all as specified and directed.

M & L for applying two coat of Oil Bound distemper on old surfaces of wall including preparation of surface complete all as specified and directed.

M & L for applying bond coat of epoxy bonding agent & cement in 1:1 ratio for bonding old and new concrete on damaged surfaces applying polymer modified mortar in CM 1:3 including mixing of polymer latex additives upto 60mm thickness (Chajjas fins, border etc) (i) Qty of ploymer to be used 15% by weight of the cement. (ii) Use of electrical mixer to get the homogeneous dough on bond coat surfaces. (iii) To achieve required thickness repear this step after 24 hrs as required.(iv) Keep the surfaces moist using water forg for 5 to 7 days etc complete all as specified and as directed. (v) Rate shall be inclusive of all necessary scaffolding for building height up to 24 meters complete all as specified and directed by Engineer-in-CHarge. Make : - Epoxy bonding agent shall be Krishna, Dr Fixit, MC Bauchemie and M/s Cemistik, Sika as directed.

Material and labour for shotcreting average thickness 30 mm in RCC columns, beams and slab etc. with cement concrete1:1.5:3 nominal mix having minimum cement content of 350 Kg per Cum. Concrete having the specified minimun characterstic compressive strength (with ordinary portland cement, coarse sand and graded stone aggregates of 6 mm maximum size in proportion as per design criteria and Hardener/ admixture) incl the cost of centering and shuttering at edges and corner etc as directed by Engineer-in-Charge incl chipping of unsound/week concrete mateial 50 mm average thickness from slabs, beams/ columns etc with mannual chiesels or standerd power driven percussion type machine incl tapering of all edges, make square shoulder of cavities incl cleaning the exposed concrete surface and reinforcement with wire brushes and throughly washing with water and allowing it to dry etc incl removal of rust by applying approved rust remover chemical and the coating with Dr Fixit Epoxy zinc primer @ 6 Sqm per Litre at DFT of 100 micron, applying the SBR Latex based bonding agent on each layer of the shootcreting work of Dr Fixit Pidicrete URP on the entire surface complete all as directed including pressure grouting with epoxy injection grout including 5 mm thick cement plaster in CM (1:3) finished even and smooth without using extra cement including removing rubbish material from building and thrown in low lying lying area at any distance upto 500 metres from the site complete as directed by Engineer-in-Charge. Contd...103.01/-

Make of chemical : Epoxy bonding agent, Rust remover, Anti corrosive coating, Epoxy grout, Hardener/ admixture shall be of Berger/ Sika/Fosroc/Pidilite or Techno commercial or equivalent make approved by GE. Notes : (i) Complete treatment to be executed by approved applicator (Applicator to be approved by GE). (ii) The Contractor and manufacture of shotcrete shall give the warranty before commencement and also for the strengths achieved in the post completion of work. (iii) The chemicals to be used in the work shall be certified by the manufacturer with whom the MOU been entered into. (iv) Hard drawn steel wire fabric will be measured and paid seperately

Supply and fixing hard drawn steel wire fabric not exc 4 kg/sqm cut to lengths, wire mesh to be fixed and firmly anchored to the concrete surface by means of 'L' shaped mild steel shear key welded with existing reinforcement including cost of material, labour, tools and plants incl welding/L-clip/tying with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and as directed.

S&F Pressed steel frames made of 1.25mm thick MS sheet of profile 125x60mm for door and window frames with one or more rebates incl lock strike plate, shock absorbers, 20mm dia 60mm long MS conduit for housing of a drop bolt, butt hinges, hold fasts/lugs etc and treating of internal surfaces of chowkhats and hold fasts/lugs with a coat of coal tar or black paint incl hinges, hold fasts/lugs etc including making good jambs portion by providing plaster in CM 1:4 and finishes as per existing complete all as specified and as directed.

M & L Pressed steel frames made of 1.25mm thick MS sheet of profile 105x60mm for door and window frames with one rebate including lock strike plate, shock absorbers, 20mm dia 60mm long MS conduit for housing of a drop bolt, butt hinges, hold fasts/lugs etc and treating of internal surfaces of chowkhats and hold fasts/lugs with a coat of coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified and as directed.

M & L Cement concrete (1:3:6), type C-1 using 20mm graded stone aggregate as in bed blocks of hold fasts, coping etc including necessary form work complete all as specified and as directed.

S&F 35mm thick, 2nd class hard wood (Hollock), glazed and skelton shutters, open rebated and prepared to receive glass/ gauge etc divided in to squares with plain rounded mitered and rebated sash bars any numbers, fitted with cut and mitered beads for securing glass etc size of members as specified in clause 8.24 (a) of MES Schedule Part-I in Section-8, complete all as specified and as directed.

S&F 30mm thick, Flush shutters, solid core construction, with partical board core, commercial type on both sides,one face is covered with deco rative face veneer with lipping/frame to match complete all as specified and as directed.

S&F 4.8 mm thick sheet glass ordinary quality and glazing fixing with rubber beads in windows/ventilators in square n. exc 0.5 Sqm in each pane complete all as specified and as directed.

S&F 4.0 mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane fixed to aluminium ventilator complete all as specified and as directed.

M & L Painting to new wooden or wood based surfaces of any description, over 10cm width or girth in two coats with synthetic enamel paint over a coat of pink primer including preparation of surfaces complete all as specified and as directed.

M & L Painting to new steel surfaces of any description, over 10cm width or girth two coats with synthetic enamel paint over a coat of red oxide primer including preparation of surfaces complete all as specified and as directed.

S & F Aluminium Anodised butt hinges, 150 mm long, fixed with galvanised mild steel hinge pin complete all as specified and as directed.

S & F Aluminium Anodised Sliding door bolt, 250 mm long with bright bolt not less than 12mm dia with & including minimum of 6 bolts and nuts, four on bolt plate and two on staple plate fixed with galvanised mild steel hinge pin complete all as specified and as directed.

S & F 15mm bore GI tubes, medium grade with all fitting and fixed complete to walls and ceilings or laid in floors including cutting chases, pinning in making good facing where required and pointing in cement mortar 1:3 to ends or edges for concealed water tubing used in brick wall and incl taking up or down existing steel water tubing, 15mm bore alongwith connections fixed/laid in any situation, complete all as specified and as directed.

All as per item above 116 herein before but 20 mm bore tubing, complete all as specified and as directed.

Supply & Fix in repairs Squatting pan orrissa pattern vitreous china white of size 580mm x 440 mm with integral foot rests including necessary lime concrete and 100 mm bore sand cast cast iron ‘P’ trap with 550 to 600 mm long neck for connecting WC to branch piece with cement joints etc complete all as specified and as directed.

S & F Low level flushing cistern, PVC (white), 10 liters capacity, with inlet ball float valve, PVC flush pipe and necessary fixing accessories and connecting to water pipe and EWC etc and fixed in repairs complete all as specified and as directed.

S & F PVC connection 15 mm size PTMT nuts of length 450 mm fixed complete all as specified and as directed.

S & F in repair PVC waste pipe of 32 mm dia for Wash Hand basin/Urinals/Sink etc complete all as specified and as directed.

S&F stainless steel sinks 1 mm thick kitchen or laboratory with plugs, washers, CP coupling and including bedding in cement mortar fixed in RCC cooking platform including fixing cantilever brackets and connecting union to pipe overall size 495 mm x 420mm & bowl size 410mm x 330mm x 160mm, complete all as specified and as directed.

S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches including dismantling CI pipe/any type alongwith fittings of 75 mm dia, below or above ground level, jointed in cement mortar and taking out complete all as specified and as directed.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches including dismantling CI pipe/any type alongwith fittings of 100 mm dia, below or above ground level, jointed in cement mortar and taking out complete all as specified and as directed.

S&F PVC rain water pipes 110mm bore including fixing to walls with MS clamps including dismantling pipe any type alongwith fittings of 100 mm dia, below or above ground level, jointed in cement mortar and taking out complete all as specified and as directed.

Demolition of reinforced cement concrete in any position not described else where complete all as specified and as directed.

M&L Factory made 60mm thick pre-cast coloured interlocking tiles PCC (M-35 Nominal Mix) over 25mm thick layer fine sand and grouted with dry sand over and including 75mm thick brick hard core complete all as specified and as directed.

S & F providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement : 3 coarse sand), including making good joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opeing opening wherever required complete @ with two coat of synthetic enamel paint over a coat of primer complete all as specified and as directed.

M & L for pcc (1:3:6) type C2 (40mm graded stone aggregate) 100mm thick as in sub base complete all as specified and as directed.

Taking down carefully existig copper / alumn point wiring for light / fan / bell / socket 5/15 Amp points complete with fitting and fixtures such as switches, sockets, c/ rosess, holders and bracket fittings with battens / conduits / wires,T/L fittings and making good the disturbed surfaces of walls and roofs etc.and to match with existing colour complete all as specified and directed.

Taking down carefully unserviceable main switches and distribution boards with fuses/ MCB's (single phase or three phase) of any capacity,and meters and making good disturbed surfaces and matching with existing complete all as specified and directed.

Taking down carefully old unserviceable sub main wiring including meters and making good disturbed surfaces and matching with existing complete all as directed and specified

S&F Point wiring complete with 1100 volts grade PVC FRLS insulated unsheathed cable of copper conductor, multi stranded of size 1.5 Sqmm, single core, drawn through & including PVC rigid concealed conduit, medium grade of suitable size (not less than 20mm dia) duly ISI marked with all accessories such as bends, reducers, spacers, saddles, junction boxes, bakelite sheets, sizes for mounting switch/sockets, fan regulators etc complete with and including continuous earth wire of size 1.5 Sqmm, single core, PVC FRLS copper conductor, insulated, unsheathed, stranded (Green colour) connected to common earth dolly complete all as specified and as directed for following : (a) One light/fan/bell/Bldg security light point controlled by one single pole one way switch.

All as per item No. 133 here-in-before but One 3 pin 5 Amp socket outlet point controlled by one switch on Independent board, complete all as specified and as directed

All as per item No. 133 here-in-before but One 3 pin 5 Amp socket outlet point controlled by one switch on same board, complete all as specified and as directed

All as per item No. 133 here-in-before but one 15 Amps socket outlet point controlled by one single pole switch one way and wiring with 2.5 Sqmm PVC FRLS insulated, stranded, unsheated copper conductor on independednt board with continuous earth wire of size 2.5 Sqmm green colours PVC FRLS insulated, unsheathed, stranded copper conductor cable, complete all as specified and as directed

All as per item No. 133 here-in-before but one 15 Amps socket outlet point controlled by one single pole switch one way and wiring with 4.0 Sqmm PVC FRLS insulated, stranded, unsheated copper conductor on independednt board with continuous earth wire of size 4.0 Sqmm green colours PVC FRLS insulated, unsheathed, stranded copper conductor cable, complete all as specified and as directed

S&F 6 amps, single pole, one way switch urea back piece (IP20), 240V, 50Hz, white in colour, duly ISI marked complete all as specified and directed. Make- Anchor/ Cona/ Plaza.

S&F Switch piano flush type 16 amps, single pole one way, white in colour, duly ISI marked complete all as specified and directed. Make- Anchor/ Cona/ Plaza.

S&F 6 Amps Socket 2 in 1, Urea backpiece (IP20), white in colour, duly ISI marked complete all as specified and directed. Make- Anchor/ Cona/ Plaza.

S&F Socket outlet, UNI, 2 in one 6 Amps & 16 Amps, white in colour, duly ISI marked complete all as specified and directed. Make- Anchor/ Cona/ Plaza.

S&F Bell push flush, type 6 amp single pole one way, white in colour, duly ISI marked complete all as specified and directed. Make- Anchor/ Cona/ Plaza.

S&F Door Bell, AC, 230 volts, single pole, white in colour, duly ISI marked complete all as specified and as directed. Make- Anchor/ Cona/ Plaza.

S&F Ceiling rose surface type, 240 volts, 50 Hz, 6A, Pilot 3 plate, white in colour, bakelite 65 x 50mm, 3 terminals duly ISI marked complete all as specified and directed. Make- Anchor/ Cona/ Plaza.

S&F batten holder, 240 volts, 50 Hz, 6A, white in colour, duly ISI marked complete all as specified and directed. Make- Anchor/ Cona/ Plaza.

S&F rotary stepped type electronic fan regulator compatible for BLDC for ceiling fan 1200/1400mm size, 240 volts, 6 Amps, 100W, deluxe, white in colour, duly ISI marked complete all as specified and as directed. Make- Anchor/ Cona/ Plaza. Make- Anchor/ Cona/ Plaza.

Supply and fixing LED light fitting 1 x 20 Watt, 220V, AC connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and as directed

S&F LED bulb of 9/10 watts B-22 CDL 3 star 6500K, complete all as specified and as directed.

S&F Factory made three phase and neutral Sheet Steel made out of CRCA 1.2 mm thick, powder coated double door vertical distribution board 4 way, dust and vermin proof, fitted with two cover, one screwed cover for incoming and outgoing MCBs and the second for protection of MCBs fitted with colour bus bar of capacity 200 Amps, neutral link, earth bar and din rail suitable for use on 240/415V, 50Hz supply, VTPN DB, partly immersed in wall, including of MCCB 4 pole adjustable thermal & fixed magnetic type 100 Amps, 50Hz, 415 Volts with rupturing capacity 16 KA and making good distrubbed surfaces with matching colour, complete all as specified and as directed. Make- HPL/ INDOASIAN/ BENLO/ HAVELLS

S&F Factory made single phase and neutral Sheet Steel made out of CRCA 1.2 mm thick, powder coated double door vertical distribution board 8 way, dust and vermin proof, fitted with two cover, one screwed cover for incoming and outgoing MCBs and the second for protection of MCBs fitted with colour bus bar of capacity 200 Amps, neutral link, earth bar and din rail. suitable for use on 240V, 50Hz supply, partly immersed in wall and making good distrubbed surfaces with matching colour, complete all as specified and as directed.

S&F Factory made single phase and neutral Sheet Steel made out of CRCA 1.2 mm thick, powder coated double door vertical distribution board 12 way, dust and vermin proof, fitted with two cover, one screwed cover for incoming and outgoing MCBs and the second for protection of MCBs fitted with colour bus bar of capacity 200 Amps, neutral link, earth bar and din rail. suitable for use on 240V, 50Hz supply, partly immersed in wall and making good distrubbed surfaces with matching colour, complete all as specified and as directed.

S&F MCB SPN, 40A - 63Amps, 240 volts, "C" series, 10KA duly ISI marked, in MCB DB, complete with connection testing and commissioning, complete all as specified and as directed.

S&F MCB SP, 6A-32 Amps, 240 volts, "B" series, 10KA duly ISI marked, in the MCB DB, complete with connection testing and commissioning, complete all as specified and as directed.

M&L for Sub main wiring with two single core 2x6 sqmm FRLS insulated and unsheathed stranded copper conductor alongwith earth wire 6.0 sqmm drawn in FRLS rigid conduit connected to main board complete all as specified and directed (Two runs cable and one number earth wire and suitable FRLS conduit shall measured together as unit length).

S&F exhaust fan heavy duty copper winding with louvers complete of sweep size 300mm, 900 RPM, single phase, with bolts, nuts and washers, size of the bolt 15 cm long 12mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/00.0076 three core from ceiling rose to exhaust fan max 1.5 mtr for giving connection, complete all as specified and as directed.

Cutting holes making good the distributed surface, grouting nuts for fixing of Exhaust fans complete all as specified and directed.

M&L for disconnecting electric meter of any cap and refixing same after rewiring, in meter box including connection, complete all as specified and as directed.

S&F Sheet metal Meter Box single door minimum size 35x50x25cm for electric meter Factory made of MS sheets/CRCA sheet duly painted with powder paint and door hinged locking arrangement conforming to IS 5039 of 1983. The electric meter/switch box shall be suitable for fixing one number of electric meter and knock out holes for incoming and outgoing cable. Before the powder paint process the sheet steel shall go through the anti corrosion conditioning process in not less than seven tank process. Concealed in wall, including making good distrurbed surfaces with matching colour, complete all as specified and as directed.

Fixing or hanging only ceiling fans height upto 3mtr to 5 mtrs ceiling height of bldg including three core FR PVC Insulated & overall round sheathed flexible with PVC, colour of cores are Red, Black & Yellow/ Green is for earthing. Sheath colour is Black of cable size 23/0.0076 complete all as specified and as directed. Note : Ceiling fans obtained/ taking down from item Sr No. 130 as above

S&F LED street light fitting toughened glass 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp incl suitable size MS/ GI bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/ 66 protection, complete all as specified and as directed.

Earthing complete with galvanized steel plate elecrode of size 60 cm x 60cm x 6.3 mm thick burried directly in ground vertically to a depth not less than 2.5 mtr below the ground level with top edge of earth plate at a depth not less than 1.5 mtr below ground level. Earth plate surrounded by 15mm thick packed alternative layers of charcoal dust and comman salt, earth lead GI wire of 4mm dia (8 SWG) by means of bolts , nuts, check nuts and washers of galvanised iron with thimbles. The other end of GI earth wire is connected to main switch board and protected by light grade GI pipe of 15 mm bore. provision of 20mm bore light grade GI pipe for watering including GI funnel and wire mesh. Pipe shallbe provided vertically upto top level of earth pit and then taken horrizontally to the earth pit. Cement concrete chamber of PCC ( 1:3:6 ) type C-2using 40 mm graded stone aggregate.The chamber shall be constructed one metre away from edge of earth pit. 50 mm thick pre cast cover of cement conrete (1:2:4) type B-1 using 20 mm graded stone aggregate and MS angle iron 50 x 50 x 6 mm frame including two coats of painting over a red oxide to sxposed steel surfaces. excavation in soft / loose soil, returning filling and removal of surplus soil to a distance of 50 mm as directed and shown in Electrical Plate No- 3 of SSR Part-1 (2009).

S&F as in repairs XLPE insulated, armoured,1100 volts grade, heavy duty cable of size 25 Sqmm nominal cross section, 4 core, flat or circular, PVC FRLS insulated aluminium conductor, served with inner sheathing of galvanized steel wire or tape and over-all PVC FRLS sheathed in service connections, laid in trenches, duct, through pipe, in floor, on pole including jointing and testing, complete all as specified and as directed.

Excavation in trenches in soft/loose soil not exceeding 1.5 metre wide and not exceeding 1.5 metre deep and not exc 10 Sqm on plan, for laying of cable and getting out, complete all as specified and as directed.

M&L Dry and clean fine sand for cable cushioning to underground cable protection, complete all as specified and as directed. (Excavation and earth work measured separately). Note- Punned down thickness shall be measured.

S&F in repair Cover to underground cable with one layer of bricks using sub class ‘B’ bricks (old size) laid flat across the cable complete all as specified and as directed. (Excavation and earth work measured separately.

Returning, filling in, earth including spreading, leveling watering and well ramming in layers each not exceeding 25cm thick each layer, complete all as specified and as directed.

Removal of surplus soil to a distance not exc. 50 metre and depositing where directed at a level not exc. 1.5 metre above the starting point complete all as specified and as directed.

S&F Mild steel galvanised pipe, light grade, 50 mm nominal bore for passing of cable, fixed to poles/walls, laid under floor/road crossings, complete with and including clamps socket & elbow etc complete all as specified and as directed.

AKASH ELECTRICALS (BID ID -3500566)

JAWAHAR CONSTRUCTION COMPANY (BID ID -3497692)

M/s Kissan Engineering Works (BID ID -3497763)

B.L. Chaudhri and Co. (BID ID -3499222)

M/S N Maini Constrution (BID ID -3500079)

M/S Yashpaul Gulati (BID ID -3502410)

M/s Harkesh Kumar Bansal (BID ID -3502712)