Construction of Balance Work Police Barrack for 40Nos NGO,s GD II at Bn Head quarters at Junga Tehsil , Distt Shimla HP

Amount

Excavation in foundation and trenches in earth work in all heights and depths in all kinds of soils, including saturated soils comprising of pick work, jumper work and blasting work both in soft and hard rock with chiseling and wedging out of rock (where blasting is prohibited) and their intermediate classification of soils including, dewatering wherever required, setting out to required lines, levels as shown on the drawing and directed by the engineer -in-charge at site., according to the HP.PWD. specification of 1990 (one thousand nine hundred ninety) volume-I (one) and sorting out useful and unuseful material and transportation of the unuseful material for disposing at dumping site (To be arranged by the contractor) as per satisfaction of Engineer- in -charge through all modes of transportation including head load ,animal load or mechanical means along with its leveling fine dressing and with all kinds of labour, machineries, tools equipments and safety measures and incidentals necessary to complete the work by mechanical means and labour ( if required ). All useful material such as stones, shingles aggregate and slates shall be properly stacked at site to the maximum possible extent in all leads and lifts through all modes of transportation and used /removed as per the direction of the Engineer - in- charge. Any loss to the public and private propriety during the course of execution and disposal of serviceable and unserviceable materials shall be the absolute responsibility of the contractor and shall have to be duly compensated by him in all respects including all incidental charges.

Providing form work with steel plates 3.15mm(three point fifteen milimetre) thick welded with angle iron in frame 30x30x5mm (thirty into thirty into five milimetre) so as to give a fair finish i/c centring, shuttering, strutting and propping etc. with wooden/steel battens and bailies in all heights or propping and centring, below supporting floor to ceiling and removal of the same for in situ- reinforced concrete and plain concrete work including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. i) Flat surfaces such as soffits of suspended floors, roofs, landing and the like. Floors etc. up to 200mm ( Two hundred milimetre) in thickness.

(ii) Beams cantilevers girders and lintels (i) Sides and soffits of beams, beam haunching cantilevers, brssumers and lintels not exceeding 1 metre ( One metre) in depth in all heights from floor.

( iii ) Edges of slabs and breaks in floors and wall: under 20 cm (Twenty centimetre) wide including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and laying cement concrete 1:5: 10(one cement: five sand: ten graded stone agg.40mm (forty milimetre)nominal size)Mechanical mixing and curing complete excluding cost of centring and shuttering in foundation and plinths required complete including carriage of all labour equipments and materials to various location through all modes of transportation with all leads and lifts as per directions of the Engineer-in-Charge.

Providing and laying cement concrete 1:6: 12(one cement: six sand: twelve graded stone agg.40mm (forty milimetre)nominal size)Mechanical mixing and curing complete excluding cost of centring and shuttering in foundation and plinths required complete including carriage of all labour equipments and materials to various location through all modes of transportation with all leads and lifts as per directions of the Engineer-in-Charge.

Providing and laying cement concrete 1:4:8 (one cement: four sand:eight graded stone aggregate 40mm (forty milimetre) nominal size) and curing complete excluding cost of form work in foundation and plinth including carriage of all labour equipments and materials to various location through all modes of transportation with all leads and lifts as per directions of the Engineer-in-Charge.

Providing and laying cement concrete 1:3:6 (one cement : three sand :six graded stone aggregate 40mm nominal size)( Forty milimetre) mechanically mixed and curing complete excluding cost of form work in foundation and plinth as per the direction of the Engineer-in-Charge but including carriage of materials up to all leads and lifts

Providing and laying upto all floor levels cement concrete work 1:1.5:3 (one cement One point five coarse sand) : three graded stone aggregate 20 mm (twenty milimetre) nominal size) to give surface including centring and shuttering but excluding cost of reinforcment and curing complete mechanical mixed and vibrated for compecting reinforced concrete upto floor all level including carriage of materials in all leads and lifts moulding as in cornices,window sills etc. exceeding 15 cm in girth including carriage of all labour equipments and materials to various location through all modes of transporation within all leads and other incidential charges. (i) Suspended Floor roofs, landing and shelves and their support balconies,beams,girders,bressumers and contilever upto floor twolevel and above including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and laying cement concrete work 1:1½:3 (one cement : one and half sand : three graded stone aggregate 20 mm nominal size) (twenty millimeters nominal size) michamically mixed and vibrated for compacting concrete and curing complete excluding cost of form work and reinforcement for reinforced concrete work, including carriage of materials within all leads and lifts and as per the direction of Engineer-in-Charge.(i) Foundation, footing, bases of columns and the like and mass concrete including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Providing mild steel/tor steel reinforcement for RCC work i/c bending, binding & placing in position including cost of binding wire complete up to all floor level/all heights including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. a) Tor steel.

Second class Brick work using common burnt clay building bricks in super structure up to all floor levels in cement mortar 1:6 (One cement : Six sand) as per the direction of the Engineer-in-Charge including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

35 mm thick factory made Solid panel PVC Door shutter, made out of single piece extruded soild PVC profiles, 5 mm (± 0.2 mm) thick, having styles & rails (except lock rail) of size 95 mmx 35 mm x 5 mm, out of which 75 mm shall be flat and 20 mm shall be tapered (on both side), having one side thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power, including reinforcing with MS tube of size 40 mm X 20 mm x 1 mm, joints of styles & rails to be mitered cut & joint with the help of PVC solvent cement, self driven self tapping screws & M.S. rectangular pipes bracket of size 190 mm X 100 mm of cross section size 35 mm x 17 mm x 1 mm at each corner. Single piece extruded 5 mm thick solid PVC Lock rail of size 115 mm x 35 mm, out of which 75 mm to be flat and 20 mm to be tapered at both ends, having 15 mm solid core in middle of rail section integrally extruded, fixing the styles & rails with the help of solvent and self driven self tapping screws of 125 mm x 11 mm, including providing 5 mm Single piece solid PVC extruded sheet inserted in the door as panel, all complete as per manufacturer's specification and direction of Engineer-in-charge

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges,zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately ). Casement window single panel with S.S.friction hinges (300 x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glass pane glazing bead of appropriate dimension. (Area of window upto 0.75 sqm.)

Providing and fixing 6mm (six milimetre ) thick cement fibre board of standard quality of approved shade & design in ceiling including fixing with approved adhesive, butt jointing and nails & screws complete including all leads and lifts as per the direction of Engineer-in Charge.

Providing and fixing 19mm (nineteen milimetre)thick water proof commercial board in shelves /box for cup boards with butt joints and fixing with nails and screws etc complete including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing 19mm (nineteen milimetre) thick commercial board water proof shutter for cup boards including fixing with nickle plated piano hinges with screws etc., complete including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Proding and fixing 8mm (eight milimetre) thick ply wood linning with butt jointing and nails ( framed work and cover fillets to be measured and paid for separartetly complete including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing square edged cover fillets (beading) 19mm x 6mm section,including mitring at junction with wood screws & nail in ceiling and lining Ist class deodar wood including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing powder coated sliding door bolt anodized colour and shade with bolts and nuts screws etc., complete: including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. ( a) 250 x16mm ( Two hundred fifty into sixteen milimetre).

Providing and fixing .magnatic catcher with screws bolts and nuts etc. M-10 (M-ten ) dia including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing chromium plated M.S. hasps and stapples (safety type) with necessary screws etc. complete (i) 90 mm thick ( Ninty milimetre) including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Kota stone slab flooring with 20mm (twenty milimetre ) thick base of cement mortor 1:4 (one cement is to four sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab. Including rubbing and polishing complete including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. i)40mm thick.( forty milimetre)

Kota stone slab 25mm (twenty five milimetre ) thick in risers of steps ,skirting dado and pillars laid on 12 mm (average) thick cement morter 1:3 (one cement is to three sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slab. Including rubbing and polishing complete including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

White glazed tiles 6 mm ( six millimetre) thickof size 30x45cm of approved shade and brand in skirting risers of steps and dado on of approved make and size 12mm ( Twelve milimetre) thick cement mortar 1:3 (one cement isto three sand) and jointing with neat cement slurry including carriage of material in all leads and liftrs :-( size thirty centimetre into twenty centimeter) as per HPPWD specification 1990 (one thousand Nine hundred Ninety ) volume-I Somany Or its Equivalent including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.

Cement concrete flooring 1:2:4 (one cement:twosand: four graded stone aggregate 20mm nominal size) laid in one layer finished with a floating coat of neat cement.including preparation of surface excluding grading complete as per the instruction of Engineer-in-Charge. including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. (i). 40mm (forty milimetre) thick.

Providing and laying granite in flooring 20 mm (average ) thickness base of cement morter 1:3 ( one cement is to three sand) including jointed with grey cement morter 1:2 ( one white cement is to two marble dust shade of marble including rubbing and polishing complete including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. a) 20 mm thick ( twenty milimetre).

Providing and laying heavy duty precast cement concrete pre polished inter locking paver blocks vibro compacted upto M-50 grade including border or kurb block grey or coloured over sub base of concrete with 25mm thick average thickness of cement mortar 1:4 (one cement : four sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks including curing rubbing and polishing complete( Sub base concrete floor to be paid for separately) including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. 60mm thick inter locked blocks.

Providing and fixing unistone cladding on RCC surface side as on faces or Arch masonary wall etc on 12 mm twelve milimetre thick in cement plaster 1:3 ( one cement:three sand) and jointed with white cement slury including scaffording etc complete iincluding carriage of material in all leads and lifts as per the direction of Engineer-in-Charge.

Providing and fixing 0.60mm ( zero point sixty milimetre) thick Tata Durashine or equivelent of approved brand & shade and design prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating including fixing with G.I. sheet drilling screws of required size prepainted to back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of Engineer-in-Charge.Tata make

Providing and fixing ridges or hips 60 cm overall with 0.45 mm thick Tata Durashine or equivelents prepainted sheet of approved brand shade and design in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer in Charges. including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. 0.60 mm ( zero point sixty millimetre) thick sheet.

Providing and fixing flushing 38 cm .overall with 0.45mm thick Tata Durashine or equivelents prepainted sheet of approved brand shade and design prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpetand bitumen washers complete with all accessories as required as per direction of the Engineer-in-Charge including carriage of materials upto all leads and lifts.

Providing and fixing 30 cm. wide 30 cm deep overall box type prepainted sheetgutter with bolts and nuts and washers etc. including making necessary connections with rain water pipe complete as per design 0.63mm thick sheet including entire carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing on wall face PVC and trenches rain water pipes of working pressure not less than 4.5 kg/sqm including filling the joints with approved adhesive complete including carriage of materials within all leads and lifts and as per the direction of Engineer-in-Charge. (i) 150 mm (one hundred fifty milimetre )Diametre pipe

Providing and fixing on wall faces PVC finolax accessories for rain water pipes including filling the joints with approved adhesive complete carriage of materials within all leads and lifts and as per the direction of Engineer-in-Charge. (i) PVC Plain door bend 150mm(one hundred fifty milimetre) dia

(ii) PVC shoe 150 mm ( one hundred fifty milimetre) dia

Providing and fixing m.s.holder bat clamps of approved design to C.I. or S.C.I pipes embeded in and including cement concrete blocks 10 x10x10 cm of 1:2:4:mix (1 cement 2 sand 4 stone graded stone aggregate 20 mm nominal size) and cost of cutting holes and making good the Wall including filling the joints with approved adhesive complete including carriage of materials within all leads and lifts and as per the direction of Engineer-in-Charge.(i) 150 mm ( one hundred fifty milimetre) diametre

Providing and fixing M.S B.P. sheet 2.00 mm( two milimetre) thick in eaves boards/ facia/ soffits and ceiling including cutting, welding to steel roof members and applying a coat of red lead p rimer etc. complete as per the instruction of Engineer in charge complete including carriage of materials within all leads and lifts and as per the direction of Engineer-in-Charge.

Steel work welded in built up sections, including hollow Section trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of red lead paint including carriage of materials upto all leads and lifts as per the directions of Engineer-in-Charge. (i)In trusses and trussed purlins in buildings including carriage of materials upto all leads and lifts as per the directions of Engineer-in-Charge.

(ii) In gratings framed guard bars,ladders,railling,brackets and similar works. including carriage of materials upto all leads and lifts as per the directions of Engineer-in-Charge.

Providing and fixing moulded hand rail of 50 mm dia M.S.welded in straight length over Mild steel. flat at top of vertical balusters including one coat of red oxide priming coat complete (Mild steel. flat and balusters of railings shall be measured and paid for separately) including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing moulded hand rail of 100 mm dia M.S.welded in straight length over Mild steel. flat at top of vertical balusters including one coat of red oxide priming coat complete (Mild steel. flat and balusters of railings shall be measured and paid for separately) including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Painting two coats (excluding priming coat) on new steel and other metal surfaces with enamel paint brushing to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matters:- With white enamel paint.or other than white including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter sand papering and knotting complete including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Painting two coats(excluding priming coat) on new wood and wood based surfaces,with enamel paint to give an even shade including cleaning the surface of dirt,dust and other foreign matter sand papering and stopping. (i) with enamel paint white other than white including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Applying Birla Two more coat white wall care putty or equivelation over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

15mm (fifteen milimetres) thick cement plasters in single coat on rough side of brick/concrete/stone walls for interior/exterior plastering upto all floor level including arises, internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth with cement mortar 1:6 (one cement: six sand) including carriage of materials within all leads and lifts and as per the direction of Engineer-in-Charge.(i) Cement mortar 1:6 (one cement is to six sand)

15mm (fifteen milimetres) thick cement plasters in single coat on fair side of brick/concrete/stone walls for interior/exterior plastering upto all floor level including arises, internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth within all leads, lifts and as per the direction of Engineer-in-Charge.(i) Cement mortar 1:6 (one cement is to six sand)

20mm ( twenty milimetre )cement plaster in single coat on fair side of brick/concrete/stone walls for interior plastering upto all floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 30cm in girth and finished even and smooth including carriage of materials within all leads and lifts :-(i) Cement mortar 1:3 (one cement is to three sand )

Distempering (two or more coats) ceiling /slopping surface with oil bound washable acrylic distemper of approved brand and manufacture of and of required shade of undecorated wall surfaces to give an even and including a priming coat withshade overAlkali-resistance primer of approved brand and manufactureafter thoroughly brushing the surface free from mortar dropping and other foreign matter and also including preparing the surface even and sand papered smooth.Priming coat with distemper primer including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Wall painting (two or more coats) with premium plastic emulsion paint of approved brand and manufacture on brand undecorated wall surfaces to give an even shade including thoroughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth including applying of putty a required for making the surfac including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge

Providing plinth protection 50mm ( fifty milimetre) thick in cement concrete 1:3:6 (1 Cement : 3 Sand : 6 graded stone aggregated 20mm nominal size) including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Providing under layer for plinth protection of 75mm thick (unconsolidated) bed dry brick/stone aggregated 40mm nominal size with rammed and consolidated and grouted with fine sand including preparation of ground including entire carriage of materials in all leads and lifts and as per the direction of Engineer-in-Charge. .

Constructing course rubble hammer dressed ‘U’ shape open surfaces drain with side wall 15x23cms (Fifteen into twenty three centimeters) in cement mortar 1:6 (One cement: Six sand) and inside plastering with cement plaster 1:3 (one cement: three sand) including earth work and laying 10cm (Ten centimeters) cement concrete in 1:5:10 (One cement: Five sand: Ten graded) crushed stone aggregate 40mm (Forty millimeters) nominal size and 7.5cm (Seven decimal five centimetres)cement concrete 1:2:4 (One cement: Two sand: Four graded) crushed stone aggregate 20mm (Twenty millimeters) nominal size and finished with a floating cost of neat cement complete as per standard design within all leads, lifts of materials and other incidentals.

Providing and laying in trenches, galvanised mild steel tubes (medium grade), tube fittings (earth work in trenches to be measured and paid separately) including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. (a) 25 mm (twenty five milimetre ) nominal bore

Providing and fixing to wall ceiling and floor galvanised mild steel tubes (Medium grade) tube fitting and clamps including making good the wall, ceiling and floor including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.15milimeters nominal bore

Making connection of galvanised steel distribution branch with galvanised mild steel main 20mm to 40mm nominal bore by providing and fixing tee including cutting and threading the pipes complete including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Fixing water meter stop-cock in galvanised mild steel tube including necessary fittings such as mild steel galvanised jam nut, sockets, etc. cutting and making long screws complete (water metre and stop-cock to be measured and paid for separately) including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. (a) 20 mm (twenty milimetre )

Providing and fixing P.V.C. water storage tank of I.S.I ; 12701 marked SINTEX or equivilent G.i. Inlet and outlet connecution, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement inculding hoisting up to all heights above ground level. including curing complete including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.(i) 1000 lters capacity

Providing and fixing vitreous China wash down, water closet squatting pan (Indian type W.C pan) Cat No. 2071 size 58X44 cm (Earth work, bed concrete, foot rest and trap to be measured and paid for separately).in white colour Of (PRIMA) Cera or its equivalent including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. i)Orrisa Patern cat No. 2071 of cera or its equilevent.

Providing and fixing vitreous China water closet squtting pan (European type W.C. ) cat No 2090 in white colour Of (PRIMA) Cera or its equivalent including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. (a) Anglo Indian Universal

Providing and fixing Plastic seat cover( solid/ hollow)for wash down water closet with c.p. brass hinges and rubber buffers (a) White plastic seat and cover including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing vitreous china wash basin cat no 10001 in white colour with single hole for piller tap with C.I. or M.S. brackets painted white inculding cutting hole and making good the same butt exculding fitting flat back size 55x40 cm Of (PRIMA) Cera or its equivalent

Providing and fixing stainless steel kitchen sink of approved standard ISI make with drain board and C.P. waste with C.I. or M.S. Brackets painted white including cutting holes and making good the same but excluding fitting. 610x510mm with bowl depth 200mm and as per the direction of Engineer-in-charge.No.6321 including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing 100 mm dia chromium plated grating of superior quality for floor, gully or nahani trap including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing 650mmx450mm bevelled edge mirror of supior glass mounted on 6mm thick A.C. sheet or ply wood sheet and fized to wooden plugs with C.P Brass screws and washer including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing C.P. Brass bib tap with capstan head ESS-ESS make including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. 15mm dia.

Providing and fixing C.P. Brass pillar tap with capstan head including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. 15mm dia.

Providing and fixing C.P. brass angle valve without nuts and pipe including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. 15mm dia

Providing and fixing CP. Brass Towel Rail complete. Fixed to wooden plugs with C.P brass screws. including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. (a) 750mmx20mm ( Seven hundred fifty milimetre into twenty milimetre).

Providing and fixing P.V.C. connection pipe with brass union including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge i) 45 cm. length 15mm nominal bore.

Providing and fixing brass full way valve with Wheel including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. (a) 25 mm ( twenty five milimetre )nominal Size

Providing and fixing Plytheline -Aluminium - Polyethylene (PE-AL -PE) composite pressure pipe U.V. stabilized with carbon black conforfing to IS -15450-2004 water supply inculding clamp at one meter spacing, cutting, fixing and making good the wall etc. but exculding the fittings (interal work) pipe exposed on wall . Interal exposed -Exposed on wall including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.i)1216 (16 mm O.D. pipe)

Providing and fixing composite end seal compression fittings as per IS-15450-2004 for cold water supply e.g. tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fittings complete including cutting and making good the walls etc. including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. a)Equal Tee .(i)1216

b)Female elbows (i) 1216 x15 mm thread (one thousand two hundred sixteen into fifteen milimetre ).

c)Male thread connector (i) 1216x15 mm thread ( (one thousand two hundred sixteen into fifteen milimetre ).

d)Female thread connector (i) 1216x15 mm thread ( (one thousand two hundred sixteen into fifteen milimetre ).

Providing and fixing PVC. floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.(i) 110x90mm ( one hundred ten into ninty milimetre).

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.(i) 160 mm ( one hundred sixty milimetre).

(ii) 110mm ( one hundred ten milimetre).

Providing and fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. complete including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. (i) 160 mm ( one hundred sixty milimetre).

(ii) 110mm ( one hundred ten milimetre).

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.(i) 160 mm ((i) one hundred sixty milimetre).

(ii) 110mm ( one hundred ten milimetre).

Providing and fixing PVC single equal branch plain ISI marked including fixing with approved adhesive etc. complete including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. i) 160 mm (one hundred sixty milimetre).

(ii) 110mm ( one hundred ten milimetre).

Providing and fixing PVC cowl ISI marked including fixing with approved adhesive etc. complete including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.(i) 110 mm ( one hundred ten milimetre).

Constructing Main hole with RCC. top Slab 1:2:4 mix in 1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) foundation concrete1:4:8 (1cement : 4 sand : 8 graded stone aggregate 40mm nominal size) inside plastering 15mm thick with cement mortar 1:3 (1cement 3 sand) finished with a floating coat of neat cement and making channels in concrete 1:2:4 mix (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) finished smooth complete including curing and testing: including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. (a) Inside size 800 mm x 800 mm and 500 mm deep including C.I cover with frame. (Light duty single seal pattern - 1) 455mmx610mm internal dimensions total weight of cover and frame to be not less than 38kg. (Weight of cover 23 kg and weight of frame 15 kg.)including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.(i) With 200mm thick walls of brick masonry using common burnt clay building bricks in cement mortar 1:3 (one cement : three Sand )

Supplying fixing RCC cover without frame for main hole including carriage of material within all leads and lifts and as per the direction of Engineer-in-Charge. a) for frame of internal diamansion 455x610mm (four hundred fifty five into six hundred ten milimetres) rectangular RCC Cover the weight of cover to be not less than 23 kg.(twenty three kilogramme) including carriage of material within all leads and lifts and as per the direction of Engineer-in-Charge.

b) For frame of 500 mm ( five hundred milimetres) internal diammeter RCC cover including carriage of material within all leads and lifts and as per the direction of Engineer-in-Charge.

Supplying fixing RCC Cover 300mmX300mm ( three hundred into three hundred milimetres)with frame for gully trap ( standard pattern) the weight of cover to the not less than 4.53 kg.( four point five three kilogramme ) including carriage of material in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing PVC low level flushing cistern White high density polyethylene / poly ropylene 10 litres capacity ( full flush) European standard control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, syphon, 15mm nominal size PVC ball valve with polythene float, with push button, couplings for connections with inlet, outlet and over flow pipe, 40mm dia C.P. flush bend including cutting holes in walls and providing and fixing making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) complete including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing CP. Brass waste for wash basin or sink including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. (a) 32 mm nominal size.

Providing and fixing PVC ‘P’ or 'S' trap for water closet (squatting pan) ISI marked including jointing the trap with the pan and PVC pipe with approved adhesive etc complete including entire carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. (i) 110 mm (one hundred ten milimetre) dia

PRAHLAD SING NEGI