REPAIR/MAINT OF CLEANING OF SEWAGE LINES, MANHOLES, SEPTIC TANK AND REPAIR TO STORM WATER DRAIN, FENCING, COMPREHENSIVE MAINTENANCE TO JOINERY OF OFFICE CUM RESIDENTIAL BLDG, REPAIR/MAINT OF LT DISTRIBUTION SYSTEM INCLUDING REPLACEMENT OF LT UG CABLE

Amount

Sch 'A' Part-I Taking out sludge including blockage and cleaning of the manhole of any size, any depth description, depth n. exc 1.50m each and removing and depositing sludge at a distance not less than 20m in a ditch including necessary excavation of pits and covering with earth & spraying unslaked lime on the covered ditch as well as around the manhole to make hygienic including necessary flushing of manhole with water after desludging, complete all as specified and directed. Note: The cost of excavation and earth work for pit, covering of ditch and providing sufficient bleaching powder shall deemed to be included in the unit quoted rate.

Dewatering/desludging & cleaning of septic tank of any depth, any size, taking out water minced with sludge and solid including any foreign materials such as stones, tree hedges etc, removing and depositing sludge at a distance not less than 20m in a ditch including necessary excavation of pits and covering with earth & spraying unslaked lime on the covered ditch as well as around the septic tank to make hygienic, complete all as specified and directed Note: The cost of excavation and earth work for pit, covering of ditch and providing sufficient bleaching powder shall deemed to be included in the unit quoted rate.

Cleaning of blockage in sewage lines/drain pipes of internal dia 100mm/150mm/200mm by rodding or by any other suitable means and cleaning the entire line and well flushing between the manholes, complete all as specified and directed.

Cleaning of blocked WC's and soil pipes of any dia up to first manhole by rodding or by any other means and well flushing with water the entire line after cleaning, complete all as directed.

Cleaning of blocked Floor/gully/nahani trap in bathroom/kitchen/wash basin etc and soil waste pipe of any dia upto gully traps by using rubber hand pump or rodding and opening the eye and making the line clear for smooth function, complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position, disposal of unserviceable materials, debris and rubbish to a distance not exceeding 100m, complete all as specified and directed. (Note:- Reinforcement shall be cut as required to facilitate demolition.)

M & L for precast RCC (1:2:4), type B-1 (using 20mm graded crushed stone aggregate) as in cover slabs (for manholes etc) and similar articles with plain faces and set in cement mortar (1:4), complete all as specified and directed.

S & F mild steel TMT bars 6mm to 8mm dia (Grade Fe-500D), cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia., or securing with clips, complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars, manholes etc. and disposal of unserviceable materials, debris and rubbish to a distance not exceeding 100m, complete all as specified and directed.

M & L for brick work with fly ash bricks old size, straight or curved on plan exceeding 6m mean radius, built in cement mortar (1:4), complete all as specified and directed.

M & L for PCC (1:2:4) type B0 (using 12.5mm graded crushed stone aggregate), cast in situ, in copings, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating as directed including use and waste of form work, complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc., complete all as specified and directed.

M & L for rendering 15mm thick in two coats (10mm+5mm each) on fair faces of brick work or concrete surfaces of wall in CM (1:4), mixed with integral water proofing compound top layer as per manufacturer's instructions and finished the surface even and smooth without using extra cement, complete all as specified and directed. (Note : WPC shall be measured and paid separately against respective item as supply only.)

M & L for rendering 15mm thick in two coats (10mm+5mm each) on other than fair faces of brick work or concrete surfaces of wall in CM (1:4), mixed with integral water proofing compound top layer as per manufacturer's instructions and finished the surface even and smooth without using extra cement, complete all as specified and directed. (Note : WPC shall be measured and paid separately against respective item as supply only.)

M & L for preparing newly plastered surfaces of walls and applying three coats of white wash, complete all as specified and directed.

Supply only liquid water proofing compound of approved quality, complete all as directed.

Dismantling of floor, hearth or wall tiles including cement mortar bedding (but not backing) and remvoing rubbish off the premishes, complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement of match over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 350x250x7mm/450x350 x7mm thick each as in skirting or dado on vertical surfaces of wall, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM (1:4), complete all as specified and directed.

Excavation in trenches not exceeding 1.5 metre wide and not exc 1.5 metre in depth for foundation of pole/stay, or cable trenches and getting out in soft/loose soil, complete all as specified and directed.

Removing of excavated materials to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 metre above the starting point in any type of soil, complete all as specified and directed.

Returning filling in incl spreading, leveling watering and well ramming in layers not exceeding 25cm in soft/loose soil, complete all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 round section) in PCC (1:2:4) type B1, smooth finished and reforming benching as required for 100mm bore pipe, complete all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 round section) in PCC (1:2:4) type B1, smooth finished and reforming benching as required for 150mm bore pipe, complete all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 round section) in PCC (1:2:4) type B1, smooth finished and reforming benching as required for 200mm bore pipe, complete all as specified and directed.

Demolition and breaking up 100mm bore drain pipes (salt glazed ware, AC or reinforced concrete) set in cement mortar, separation of serviceable materials from the unserviceable, stacking the serviceable materials within 100m and disposal of unserviceable materials, debris and rubbish to a distance not exceeding 100m, complete all as specified and directed.

All as per item No.26.00 here-in before but for 150mm bore pipe, complete all as specified and directed.

All as per item No.26.00 here-in before but for 200mm bore pipe, complete all as specified and directed.

M & L for PCC (1:3:6), type C 2, (using 40mm graded crushed stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 100mm bore pipe, complete all as specified and directed.

All as per item No.29.00 here-in before but for 150mm bore pipe, complete all as specified and directed.

All as per item No.29.00 here-in before but for 200mm bore pipe, complete all as specified and directed.

M & L for 100mm bore salt glazed stone ware drain pipes, grade 'A', laid in trenches and jointed in cement mortar and tested, complete all as specified and directed.

All as per item No.32.00 here-in above but for 150mm bore, complete all as specified and directed.

All as per item No.32.00 here-in above but for 200mm bore, complete all as specified and directed.

S&F in repair vitreous china squatting pan ,"Orissa pattern" white, size 580x 440mm with integral foot rest, 'P' or 'S' trap, including provision of lime concrete bedding, connection to trap, and to flushing pipe and vitreous china foot rest etc. complete making good to disturbed surfaces of floor to match with existing specifications, complete all as specified and directed.

S&F in repair wash down water closet EWC (cascade type) vitrious china, including plastic seat of same colour of WC, closed pattern with flat bottom, cover and mild steel chromium plated hinging device, complete all as specified and directed.

Taking down soil/waste vent and rain water pipes including all fittings of any size and pattern and in any position, complete all as specified and directed.

S & F 110mm bore PVC SWR pipe, single socketed, in any length with rubber ring joint, fixed to wall with and including clamps, complete all as specified and directed.

All as per item No.38.00 here-in-before but except pipes, complete all as specified and directed. (Note : Serviceable pipes obtain from item No. 37 shall be re-used).

S & F 110mm bore PVC SWR pipe, single socketed, in any length with rubber ring joint, laid in trenches or floor, complete all as specified and directed.

S & F 75mm bore PVC SWR pipe, single socketed, in any length with rubber ring joint, fixed to wall with and including clamps, complete all as specified and directed.

All as per item No.41.00 here-in-before but except pipes, complete all as specified and directed. (Note : Serviceable pipes obtain from item No. 37 shall be re-used).

S & F 75mm bore PVC SWR pipe, single socketed, in any length with rubber ring joint, laid in trenches or floor, complete all as specified and directed.

S&F in repair of 110mm bore, PVC (SWR) bends of any radius with access door, complete all as specified and directed.

S&F in repair of 75mm bore, PVC (SWR) bends of any radius with access door, complete all as specified and directed.

S & F 110mm bore PVC (SWR) junction single, (single T) equal or unequal, complete all as specified and directed.

S & F 110mm bore PVC (SWR) branch piece, single (single Y) equal or unequal, complete all as specified and directed.

S &F in repair 75mm bore PVC (SWR) floor trap, plain with grating including jointing to waste pipe with solvent cement, complete all as specified and as directed.

S&F in repair PVC flexible waste pipes, 40mm dia, 800mm long, for sinks/wash hand basins complete all as specified and directed.

S&F in repair PVC flexible waste pipes, 32mm dia, 800mm long, for sinks/wash hand basins complete all as specified and directed.

S&F in repair vitreous china wash hand basin white flat back of size 630x 450mm including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixinf of supply and waste pipe, complete all as specified and directed.

S&F PVC connection 15mm size with PTMT nuts at both ends 600mm, complete all as specified and directed.

S&F in repair 10 ltrs capacity low level valve less PVC syphonic action type flushing cistern white with inlet ball valve, float and handle and connection to flush pipes of polyethylene of low or high density or PVC 32mm dia, complete all as specified and directed.

S&F in repairs 32mm dia waste coupling of PTMT (half or full threaded) (minimum weight 32mm-45gms), complete all as specified and directed.

S&F in repair CP pillar tap, 15mm bore, capstan head, screwed down high pressure with or without lettered “hot’ or “ cold” with long screwed shanks and fly nuts screwed for iron pipe, complete all as specified and directed.

S&F in repairs 15mm bore, fancy type, chromium plated, stop valves,concealed type, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or union, complete all as specified and directed.

M&L for PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) as in cement concrete in foundations, filling and mass concrete, complete all as specified and directed.

M&L for PCC (1:3:6) type C-2 (using 40mm graded crushed stone aggregate) as in cement concrete in surfaces channels and drains, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and as directed.

S&F framed work such as grills,gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe.290, Gde-E-165, complete all as specified and directed.

S&F framed brackets of agles or tees web and flangs cut to shape, drilled and countersunk for screw including bending and welding angles as necessary gusset plates, riveting etc. n. exc. 10 kg each brackets conforming to Fe.290, Gde-E-165, complete all as specified and directed.

S&F in repair galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured), complete all as specified and directed.

Dismantling fencing wire mesh, any type, complete all as specified and directed.

Supply only chain link MS galvanisd fencing, any size or type, complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire, complete all as specified and directed.

M&L for preparation of new steel surfaces of any description n. exc. 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint (1st grade quality) over a coat of red oxide primer, complete all as specified and as directed.

Taking down chowkat with shutter (without taking off shutter from the frame) exc 1.5 Sqm but n.exc. 4 Sqm each, complete all as specified and directed.

Taking down chowkats with shutter (without taking off shutter from the frame) not exc. 1.5 Sqm each., complete all as specified and directed.

Taking down shutter of any description exc. 1 Sqm but n.exc 2 Sqm each, complete all as specified and directed.

S&F 125X60mm size factory made pressed steel frames for doors, made out of 1.25mm thick PBI sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified and directed.

S&F 105X60mm size factory made pressed steel frames for doors, made out of 1.25mm thick PBI sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified and directed.

M&L for pre-cast reinforced cement concrete (1:2:4) type B-0 (using 12.5mm graded crushed stone aggregate) as in door and windows frame, any size, single or double rebated including arrangements for fixed of hinges and fixures as required, complete all as specified and directed.

S&F 2nd class hardwood plain,solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints, complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, as per specification & drawings, complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified and directed.

S&F 35mm thick 2nd class hardwood glazed and skeleton door shutter open rebated and prepared to receive glass edges of frames plain cahmfered por rounded fitted with cut and mitred beads for securing glass etc., complete all as specified and directed.

M&L 35mm thick 2nd class hardwood factory made plain framed panelled shutter (two panel) with lock rail and panel of 9mm B.W.P commercial ply or 12mm veneered particale board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I) kiln seasoned and chemically pressure treated, complete all as specified and directed.

M&L for preparation of new or previously untreated wooden surfaces of any description exc. 10cm in width or girth not otherwise described and applying two coats of synthetic enamel paint (1st grade quality) over a coat of pink primer, complete all as specified and directed.

S&F powder coated anodised aluminium frame for doors window/ventilator and partitions etc. with one or more rebates including joining cleat for fixing etc., complete all as specified and directed.

S&F powder coated anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc., complete all as specified and directed.

S&F powder coated aluminium window/ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 Sqn kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodized aluminium fittings such as peg stays 150mm long (1 No.). hinges type B-21, 100mm long (2 No.) suitable handle (1No.), complete all as specified and directed.

S&F sheet plain glass 4.8mm thick, of any colour and glazing with and including anodised aluminium snap beading or rubber/neopren bead, fixed in aluminum frame either in window/ventilator or door frame, complete all as specified and directed.

S&F floor door stopper 150mm long of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, complete all as specified and directed.

S&F of 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type, on both sides, complete all as specified and directed.

S&F second class hard wood 15mm thick boarding, clean sawn with butt joints, fixed with nails in any situation, as shelves of built-in-cupboard including replacement of old and or decayed boarding in patches including cutting out old, piecing, heading joints, etc., complete all as specified and as directed.

S&F 100mm long, butt hinges,medium weight, cold rolled, complete all as specified and directed.

S&F aluminium alloy, anodised, sliding door bolt 300mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, complete all as specified and directed.

S&F 200mm long aluminium anodised barrel tower bolt of extruded section, complete all as specified and directed.

S&F 150mm long aluminium anodised barrel tower bolt of extruded section, complete all as specified and directed.

S&F 150mm long extruded aluminium alloy handles, fabricated type anodised, complete all as specified and directed.

S&F 125mm long extruded aluminium alloy handles, fabricated type anodised, complete all as specified and directed.

S&F MS flat as in clamps, hold fast, hook, washer & similar small articles confirming to Fe-290 Gde-E-165, complete all as specified and directed.

M&L for PCC (1:3:6) type C-1, (using 20mm graded crushed stone aggregate) as in hold fast blocks etc, complete all as specified and directed.

S&F in repair galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.00mm and fixed with tinned tacks, or galvanised wire staples, complete all as specified and directed.

S&F in repair mild steel 300mm ordinary rat tail rod pattern springs including roller and roller plate of mild steel, complete all as specified and directed.

S&F in repair 100mm hasp & staple safety type aluminium anodised with mild steel hing pin including bolt to hinge plate and fixed with screw, complete all as specified and directed.

S &F in repair continuous (piano) hinges, mild steel, bright finish or electrogalvanised width of flaps 30mm (when open), complete all as specified and directed.

S &F in repair ball catches with 8mm dia steel ball, and brass body striking plate including letting in and fixed, complete all as specified and directed.

S&F in repair of aluminum body door closer (extruded section) hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 kg and fixed, complete all as specified and directed.

M&L for steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, complete all as specified and directed.

S&F of steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

Hacking out old broken glass any thickness size quality or description from metal frame including punching or drilling our old glazing pins/spring clips, complete all as specified and as directed.

M&L for 4mm thick figured glass, pin head type and glazing with oil putty in squares n. exc. 0.5 Sqmm in each pane, complete all as specified and directed.

M&L for 4.00mm thick sheet glass, ordinary quality and glazing with oil putty/wooden beads in square n exc 0.5 sqm in each pane, complete all as specified and directed.

M&L 15mm thick rendering in CM (1:6) on other than fair faces of brick work or concrete surfaces of wall, finished even and smooth without using extra cement, complete all as specified and directed.

M&L for preparation of newly plastered or unplasterd wall surfaces and applying two coats of oil bound distemper over a coat of chalk whitening primer, complete all as specified and directed.

M&L for preparation of newly plastered or unplasterd wall surfaces and applying two coats of cement base paint over a coat of alkali resistant primer, complete all as specified and directed.

S&F coloured PVC designer modular wall cladding 5 to 6mm thick with air gap between installed with 'U' shaped GI channel with end joints on edges (design, colour patterns as directed by GE). The frame work of suitable size will be fixed to wall using aluminium screws including necessary demolition/dismentaling of existing unserviceable ceiling boards of any description/thickness and including cover fillets, complete all as specified and as directed. (Note :- Cost of frame work shall deemed to be included in the unit rate.)

M&L for 4mm thick pre-painted E-fibre board, designer/decorative, fixed or laid/inserted to GI snap grid frame size 605x605 mm work for false ceiling hangers with 4mm to 6mm dia. G.I. (length as required) adjusting level, fixed to roof slabs/truss by means of ceilling cleats made out of G.I. flat 40 x 3mm size 60mm long and expansion hold fasteners, 12.5mm dia, 40mm long including necessary demolition/dismentaling of existing unserviceable ceiling boards of any description/thickness and including cover fillets, complete all as specified and directed.

Supply, installing, testing and commissioning of out door type LT distribution box in replacement made out of 3.15mm thick CRCA sheet out door type, totally enclosed weather dust and vermin proof as per IS with front and rear opening suitable locking arrangement having copper bus bar of 600 Amp capacity for RYB and neutral and insulated with insulators, including connecting incoming and outgoing cables necessary PCC (1:3:6) in foundation and made out of 50 X 50 X 6mm angle iron grouted above 30cm from ground level including comprising the following:- Incoming:- (i) MCCB 100 Amp 4 pole 27 KA with adjustable thermal and fixed magnetic type - 01 No. (ii) Digital multi function Meter 01 - 500 Volt (iii) RYB Indicating lamps -03 Nos (iv) CT's 100 /5 Amp - Set of three Outgoing:- (i) MCCB 63 Amp, 4 pole, 10 KA with adjustable thermal and fixed magnetic type - 02 Nos (ii) MCCB 32 Amp, 4 pole, 10 KA with adjustable thermal and fixed magnetic type - 04 Nos Note : Unit quoted rate shall deemed to be included for necessary internal wiring for meters, CTs, indication lamps, etc and rigid bus bar connections from bus bar to MCCB terminals connection bus to MCCB/MCB connections.

S&F on load change over switch 415V in sheet metal enclosures 4 pole of capacity 250 Amps with barrier, handle and door locking kit system and necessary connection between two power sources as per site requirement, complete all as specified and directed.

S&F 4 pole MCCB 63 Amp, 50 Hz, 415 V with rupturing capacity 25 KA with adjustable thermal and fixed magnetic type, complete all as specified and directed.

S&F 4 pole MCCB 100 Amp, 50 Hz, 415 V with rupturing capacity 25 KA with adjustable thermal and fixed magetic type, complete all as specified and directed.

S&F 4 pole MCCB 125 Amp, 50 Hz, 415 V with rupturing capacity 25 KA with adjustable thermal and fixed magetic type, complete all as specified and directed.

S&F 4 pole MCCB 160 Amp, 50 Hz, 415 V with rupturing capacity 25 KA with adjustable thermal and fixed magetic type, complete all as specified and directed.

S&F in replacement LED type spike light 9/10 watt out door type 230 volts AC outdoor type, die cast aluminium housing, IP-65 protection, including necessary PCC fundation of size not less than 300 X 300 X 600mm, complete all as specified and directed.

S&F in replacement post top lantern LED type 40 watt 230 volts AC outdoor type with decorative post top for 360 degree indirect light, IP 65 protection, with impact and corrosion resistant complete with driver and lamp, complete all as specified and directed.

S&F post top lantern LED type 25 watt 230 volts AC outdoor type with decorative post top for 360 degree indirect light, IP 65 protection, with impact and corrosion resistant complete with driver and lamp, complete all as specified and dirtected.

S&F bollard LED type 9/10 watt 230 volts AC, aesthetically design, outdoor type with necessary foundation, piece of GI pipe and connection strip complete with driver and lamp, complete all as specified and directed. Make: Havell's Cat Part No. UFOBLS10WLED857PSYMTOPC(600), Bajaj Cat Part No.111771 BGBOS 600, Crompton Cat Part No. LBLSN-10-CDL

M & L for XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavyduty) with aluminium conductor, 1100 volts Earthed,grade cross sectional area 70 Sqmm 3½ core conforming to IS-7098 laid in trenches/ducts/fixed on poles wall/laid under roads/paths/drain/culverts or passing through pipes, complete all as specified.

All as per item No.120.00 here-in-before but crosssectional area 25 Sqmm, 3.5 core, complete all as specified and directed.

All as per item No.120.00 here-in-before but crosssectional area 16 Sqmm, 4 core, complete all as specified and directed.

All as per item No.120.00 here-in-before but crosssectional area 10 Sqmm, 4 core, complete all as specified and directed.

Supply and laying double walled corrugated (DWC) HDPE duct pipe of 40mm dia conforming to IS, approved colour complete with fittings for cable protection, complete all as specified and directed.

Supply and laying double walled corrugated (DWC) HDPE duct pipe of 50mm dia conforming to IS, approved colour complete with fittings for cable protection, complete all as specified and directed.

S & F junction box made from SMC/FRP sheet ready made of size 350X 250 X138mm with aluminium bus bar of 100 Amp capacity for RYB and for neutral made in suitable size fixed inside the junction box with necessary supporting insulators, fixed on hylem sheet, MS sheet steel fixed inside the bottom portion of box to connect the cable gland complete , entire assembly fixed to pole/wall with MS clamp 25 X 5mm and nuts & bolts, or inside the copping of pole/post top including MCB SP 6 Amp 10 KA 'C' series 240 V - 1 No, with suitable size copper lugs for connecting cables from junction box to fittings, complete all as specified and dirtected.

S&F in replacement LED street light fitting 90 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection, complete all as specified and directed.

M & L for painting steel tubular poles 9.0m height above GL including cross arm and bracings on existing surface after cleaning and removing dust, rust & dirt with one coat of red oxide primer and two coats of aluminium paint (1st grade quality), numbering of pole with (MES/Sl-Number) with synthetic enamel paint and white wash on pole coping, complete all as specified and directed.

Taking out 200 KVA unserviceable stabilizer from site by dismantling all electrical connectiion from panel and rearrange for bypass connection, temporary basis, and carry to the contractors workshop and dismantle the outer and inner fittings part by part carefully and repair/replacement of all under mentioned unserviceable spare parts along with connectivity accessories including overhauling other parts complete and reinstall its previous place with proper connection by thimboling all termination end of cable as directed, complete all as specified and directed.

Taking out burnt out coil from stabilizer of capacity 200 KVA and rewinding the same with DPC copper wire of existing gauge and weight with insulating materials for LT coil of approved quality, complete all as specified and directed.

S & F control PCB card suitable for 200 KVA stabilizer, complete all as specified and directed.

M&L for rewiring control circuit partially with single core copper conductor as per existing size including labour charge complete for 200 KVA stabilizer, complete all as specified and directed.

Supply and filling up transformer oil (Grade 'B') in Transformers and Oil Circuit Breakers installed at various Sub stations, having Di-electric strength not less than 40 KV on 4mm over gap for a period of one minute, complete all as specified and directed.

S&F in replacement power contactors 4 pole power contactors, 40 Amp, ML- 3, 2 NO+2 NC for street light after dismantling existing contactors from panel and connecting new contactors and making connection with incoming and outgoing MCCB/MCB, complete all as specified and directed.

S&F in replacement for electronic timer for 24 hrs, top mounting for all contactors (frame 1 to 4) suitable for street light application, complete all as specified and directed.

M & L for laying and spreading 40mm graded crushed stone aggregate at different E/M installations, complete all as specified and directed.

M & L for laying and spreading 20mm graded crushed stone aggregate at different E/M installations, complete all as specified and directed.

M & L for laying and spreading 12.5mm graded crushed stone aggregate at different E/M installations, complete all as specified and directed.

Supply, installing, testing and commissioning of in door type LT panel board made out of 2.0mm thick CRCA sheet, totally enclosed weather dust and vermin proof as per IS with front and rear opening suitable locking arrangement having copper bus bar of 800 Amp capacity for RYB and neutral and insulated with insulators, including connecting incoming and outgoing cables necessary PCC (1:3:6) in foundation and made out of 50 X 50 X 6mm angle iron grouted above 30cm from ground level including dismantling of old LT panel board of any description/size andcomprising the following:- Incoming:- (i) MCCB 250 Amp 4 pole 36 KA with adjustable thermal and fixed magnetic type - 02 Nos. (ii) On load change over 250 Amp 4 pole 36 KA - 01 No. (iii) Digital multi function meter 0 - 500 Volt (iv) LED type Indicating lamps -03 Nos (v) CT's 500 /5 Amp - Set of three Outgoing:- (i) MCCB 200 Amp, 4 pole, 36 KA with adjustable thermal and fixed magnetic type - 02 Nos. (One working and one Spare) (ii) MCCB 63 Amp, 4 pole, 36 KA with adjustable thermal and fixed magnetic type - 01 No. Note : Unit quoted rate shall deemed to be included for necessary internal wiring for meters, CTs, indication lamps, etc and rigid bus bar connections from bus bar to MCCB terminals connection bus to MCCB/MCB connections.

S&F bracket for fixing to street light poles, made out of 50mm bore medium grade GI pipe, bend to shape including preparation of surfaces and applying two coats of aluminium paint over a coat of red oxide primer, complete all as specified and directed.

S & F in replacement 3 core PVC insulated unsheathed multistranded copper conductor cable of size 2.5 Sqmm passing through PVC conduit from junction box to fittings, complete all as specified and directed. (Note: PVC conduit shall be measured and paid seperately.)

S & F in replacement rigid PVC non metalic flexible conduit 20mm dia heavy duty, on pole with necessary bend elbow, couplers, check nuts, FI clamp 40 x 4mm fixed to poles with nuts & bolts, connected from junction box to fitting etc. including painting to clamps, complete all as specified and directed.

Supply and laying in trenches/fixed on wall 50mm bore GI tubing, light grade, with necessary fittings such as bend, tee, elbow etc complete for protection of LT UG cable, complete all as specified and directed.

Supply and erection of asthetically designed decorative hot dipped galvanised mild steel step pole 3.0 Mtrs height, opening window of 300 x 110mm for terminal connection, including mounting accessories and foundation bolts with grey powder finish compatible for fixing post top luminaire of 45 Watt, including necessary excavation and earth work, PCC foundation (1:3:6) type B-1 as per manufacturer's instructions, complete all as specified and directed. Make: Havell's Cat Part No. ECO POLE 3M TOP Ø 76 MM or equivalent model of make Philips/ Crompton/Bajaj. (Note : Post top luminaire shall be measured and paid seperately.)

S&F in replacement post top lantern LED type 45 watt 230 watt volts AC outdoor type with decorative post top for 360 degree indirect light, IP 65 protection with impact and corrosion resistant complete with driver and lamp, complete all as specified and directed. Make: Crompton Cat Part No. LPTOI-45-CDL, Havells Cat Part No. RINKPT45WLED757PSYMTOPC, Bajaj Cat Part No. BGCPNP 45 LED WW.

Sch 'A' Part-II (REPAR TO FURNITURE) REPAIR TO ALMIRAH LARGE STEEL (FD- 1031) Taking down old unserviceable locking devise of almirah large steel and supply and fixing new lock of suitable size provided with duplicate keys as per sample, fixed with screws, all as per drawing, complete all as specified and directed.

M & L for repairing locking device of almirah steel large including lock bar, complete all as specified and directed.

M & L for repairing of door shutters by denting and necessary adjustment as required, complete all as specified and directed.

Taking down old unserviceable handle of almirah large steel and supply and fixing new chromium plated handle, fixed with screws, all as per drawing, complete all as specified and directed.

Taking down old unserviceable legs of almirah large steel and supply and fixing new legs made out of 1mm thick mild steel black sheet, all as per drawing, complete all as specified and directed.

Taking down old unserviceable shelves of almirah large steel and supply and fixing new shelves made out of 1 mm thick mild steel black sheet made to shape, all as per drawing, complete all as specified and directed.

M & L for scrapping out old painted (external and internal) surface of almirah large steel and applying spray painting two coats of synthetic enamel paint (1st grade quality) over a coat of red oxide zinc chrome primer by spray painting including preparation of surfaces and filling cavities with putty, complete all as specified and directed.

REPAIR TO LOCKER STEEL (FD- 1029) Taking down old unserviceable legs of locker steel and supply and fixing new legs made out of 1mm thick mild steel black sheet, all as per drawing, complete all as specified and directed.

M & L for replacement for old damaged hasp and staple with new hasp and staples of chromium plated safety type 100mm long, complete all as specified and directed.

Taking down old unserviceable handle of locker steel and supply and fixing new chromium plated steel handle, of 100mm size, ‘D’ type, complete all as specified and directed.

Taking down old unserviceable hinges of locker steel and supply and fixing new mild steel hinges, 75mm size of approved quality, complete all as specified and directed.

M & L for repairing of door shutters by denting and necessary adjustment as required, complete all as specified and directed.

M & L for scrapping out old painted (external and internal) surface of almirah large steel and applying spray painting two coats of synthetic enamel paint (1st grade quality) over a coat of red oxide zinc chrome primer by spray painting including preparation of surfaces and filling cavities with putty, complete all as specified and directed.

REPAIR TO CHARPOY GI PIPE (FD-220) S&F in repair of angle iron of size 25 x 25 x 5mm thick, 225mm long welded to long rail and short rail at corners of Charpoy GI Pipe drilling holes for fixing plywood with bolts and painting to angle iron pieces with two coats of black synthetic enameled paint over a coat of red oxide zinc chrome primer, complete all as specified and directed.

S&F in repair of angle iron of size 25 x 25 x 5mm thick, 850mm long welded to long rail horizontally (one end to each long rail) at equal distance including drilling holes where ever required for fixing plywood with bolts and painting to angle iron pieces with two coats of black synthetic enameled paint over a coat of red oxide zinc chrome primer, complete all as specified and directed.

Taking out old plywood and replacement of commercial plywood of Size 1950mm x 900mm x 12mm thick grade BWR confirming to IS 303-1975 with 4mm wide 2nd class hard wood beading all-round the plywood, fixed to charpoy frame with and including nuts, bolts and GI washers (minimum 12 Nos. per charpoy), dia of bolt not less than 8mm, complete all as specified and directed.

S&F in repair of long rail of charpoy GI pipe, made out with 32mm bore GI pipe, medium grade including cutting threading etc, complete all as specified and directed.

S&F in repair of short rail (converted from U/S long rail) of charpoy GI pipe, complete all as specified and directed.

S&F in repair of legs converted from U/S short rail, (complete with clamps for FMN set) of charpoy GI pipe, complete all as specified and directed.

S&F in repair of wooden plugs of charpoy GI pipe, made of 2nd class hard wood as per drg, complete all as specified and directed.

S&F in repair of GI elbow three way (ISI marked) 32mm dia of charpoy GI pipe, complete all as specified and directed.

S&F in repair of GI check nut (ISI marked) of charpoy GI pipe, complete all as specified and directed. ( Note for Sl item No. 161.00 to 166.00 : Dismantling of old unserviceable / worn out threaded following parts of the charpoy GI pipe and replace the same with new part without damaging other part all as per drg)

REPAIR TO ALMIRAH MEDIUM STEEL (FD- 1032) Taking down old unserviceable locking device from almirah medium steel and supply and fixing new lock of suitable size provided with duplicate keys, complete all as specified and directed.

M & L for repairing of door shutters by denting and necessary adjustment as required, complete all as specified and directed.

Taking down old unserviceable handle and supply and fixing new chromium plated brass handle, of size 125mm, fixed with screws, all as per drawing, complete all as specified and directed.

Taking down old unserviceable legs of almirah medium steel and supply and fixing (by welding) new legs made out of 1mm thick mild steel black sheet, all as per drawing, complete all as specified and directed.

Taking down old unserviceable shelves of almirah medium steel and supply and fixing new shelves made out of 1mm thick mild steel black sheet made to shape, all as per drawing, complete all as specified and directed.

M & L for scrapping out old painted (external and internal) surface of almirah large steel and applying spray painting two coats of synthetic enamel paint (1st grade quality) over a coat of red oxide zinc chrome primer by spray painting including preparation of surfaces and filling cavities with putty, complete all as specified and directed.

REPAIR TO CHAIR EASY (FD-229) S&F in repair of damaged front legs of chair easy with well seasoned 1st class teakwood, all as per drawing, complete all as specified and directed.

All as per item No. 174.00 here-in-before but rear legs, complete all as specified and directed.

All as per item No. 174.00 here-in-before but arm rest of chair easy, complete all as specified and directed.

All as per item No. 174.00 here-in-before but fillet for canning, complete all as specified and directed.

All as per item No. 174.00 here-in-before but rail of seat and back, complete all as specified and directed.

M&L for preparation of surfaces by removing of old existing fade out polish from chair wooden bottom by scrapping or with caustic soda and rubbed down by emery paper including filled up the cracks and pores with a paste of putty and applying two coats of french polish of approved quality/PFU with high glossy finish on exposed surfaces to view, complete all as specified and directed.

REPAIR TO CHAIR DINING (FD-279) S&F in repair of damaged front leg of chair dining with well seasoned 1st class teak wood, all as per drawing, complete all as specified and directed.

All as per item No. 180.00 here-in-before but rear leg, complete all as specified and directed.

All as per item No. 180.00 here-in-before but back rest, complete all as specified and directed.

All as per item No. 180.00 here-in-before but stiffener, complete all as specified and directed.

All as per item No. 180.00 here-in-before but side rail, complete all as specified and directed.

All as per item No. 180.00 here-in-before but front rail, complete all as specified and directed.

All as per item No. 180.00 here-in-before but back rail, complete all as specified and directed.

All as per item No. 180.00 here-in-before but fillet, complete all as specified and directed.

M&L for preparation of surfaces by removing of old existing fade out polish from chair dining by scrapping or with caustic soda and rubbed down by emery paper including filled up the cracks and pores with a paste of putty and applying two coats of french polish of approved quality/PFU with high gloss finish on exposed surfaces to view, complete all as specified and directed.

REPAIR TO PEG TABLE ( FD- 277 & 384) S&F in repair of top of peg table with 18/19mm thick pre-laminated particle board one side teak face (exterior grade) with 4mm thick teak wood edging all round, all as per drawing, complete all as specified and directed.

S&F in repairt of leg of peg table with new legs of required size made out of well seasoned 1st class teak wood, all as per drawing, complete all as specified and directed.

S&F in repair of damaged side/front rail of peg table with well seasoned 1st class teakwood, all as per drawing, complete all as specified and directed.

Taking out broken stiffener/bottom rail of peg table and supply and fixing new stiffener/bottom rail of required size made out of well seasoned 1st class teak wood, all as per drawing, complete all as specified and directed.

M&L for preparation of surfaces by removing of old existing fade out polish from peg table by scrapping or with caustic soda and rubbed down by emery paper including filled up the cracks and pores with a paste of putty and applying two coats of french polish of approved quality/PFU with high gloss finish on exposed surfaces to view, complete all as specified and directed.

REPAIR TO TABLE DINING FOR 4/6 PERSONS (FD- 273 & FD/MAP-II/03) Taking down old unseviceable top from table dining and S&F new top of table dining 4 persons made out of exterior grade prelaminated MDF board 18mm thick, complete all as specified and directed.

S&F in repair of top of table dining 6 persons with 18/19mm thick pre-laminated particle board one side teak faced (exterior grade) with 4mm thick teak wood edging all-round, all as per drawing, complete all as specified and directed.

S&F in repair of damaged long rail of table dining 4 persons with well seasoned 1st class teakwood, all as per drawing, complete all as specified and directed.

S&F in repair of damaged long rail of table dining 6 persons with well seasoned 1st class teakwood, all as per drawing, complete all as specified and directed.

S&F in repair of damaged short rail of table dining 4/6 persons with well seasoned 1st class teakwood, all as per drawing, complete all as specified and directed.

M&L for preparation of surfaces by removing of old existing fade out polish from table dining 4 persons by scrapping or with caustic soda and rubbed down by emery paper including filled up the cracks and pores with a paste of putty and applying two coats of french polish of approved quality/PFU with high gloss finish on exposed surfaces to view, complete all as specified and directed.

All as per item No. 199.00 here-in-before but for table dining 6 persons, complete all as specified and directed.

REPAIR TO SOFA SET 4/5 SEATER (FD-281/373) Supply of foam cushion of size 530mm X 500mm X 100mm thick (32 grade high density cool foam) covered with tapesty cloth (not less than Rs.225/- per mtr cost of cloth) including stitching, complete all as specified and directed.

S&F in repair of damaged front legs of Sofa set with well seasoned 1st class teak wood, all as per drawing, complete all as specified and directed.

S&F in repair of damaged rear legs of Sofa set with well seasoned 1st class teak wood, all as per drawing, complete all as specified and directed.

S&F in repair of damaged arm-rest of Sofa set with well seasoned 1st class teak wood, all as per drawing, complete all as specified and directed.

S&F in repair of damaged front and back rail of seat and back of sofa set with well seasoned 1st class teakwood, all as per drawing including taking out old rail, complete all as specified and directed.

S&F in repair of damaged side rail of seat and back of sofa set with well seasoned 1st class teakwood, all as per drawing, complete all as specified and directed.

Taking out broken stiffener of sofa set seat and back and supply and fixing new stiffener of required size made out of well seasoned 1st class teak wood, all as per drawing, complete all as specified and directed.

M&L for preparation of surfaces by removing of old existing fade out polish from sofa set 5 person by scrapping or with caustic soda and rubbed down by emery paper including filled up the cracks and pores with a paste of putty and applying two coats of french polish of approved quality/PFU with high gloss finish on exposed surfaces to view, complete all as specified and directed.

All as per item No. 208.00 here-in-before but for sofa set 4 persons, complete all as specified and directed.

RECANNING OF CHAIR DINING/CHAIR EASY (FD/DB) Taking down old worn out plastic cane from chair dining/chair writing/chair easy/Stool dressing and reweaving the same with new approved quality plastic cane 3mm wide half round, white, with bordering of 4mm wide half round white plastic cane, canning shall be done in godrej pattern, complete all as specified and directed.

TABLE CENTRE (FD-274) M&L for preparation of surfaces by removing of old existing fade out polish from table center by scrapping or with caustic soda and rubbed down by emery paper including filled up the cracks and pores with a paste of putty and applying two coats of french polish of approved quality/PFU with high gloss finish on exposed surfaces to view, complete all as specified and directed.

Note: An amount of Rs.55,415.00 on account of Credit Schedule for schedule 'A' Part - III shall be deducted from the total amount of BOQ to arrive at the contract sum.

M/S BIJAY KUMAR SHIVA

B L SHARMA

M/S. NARENDRA KUMAR GARG

BHARAT ELECTRIC

M/S RATHIN ENTERPRISES