Proposed Expansion of Surveillance System at Jharkhand High Court Campus, Dhurwa, Ranchi.

Amount

100 mm X 100 mm X 60 mm deep

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess includingcutting the wall and making good the same in case of recessed conduit as required. Preferred Make- AKG/NORPACK/Polycab/Dauphin

SITC of Single Phase Online 05 KVA UPS Preffered Make-Delta/EATON/Numeric/BPE

NON SCHEDULE ITEMS SITC of Industrial Grade POE+ Layer 2 Fully Manageable Network Switch with Fixed-configuration half-rack width chassis with eight 10/100/1000 Base-T POE+ ports, two Gigabit combo ports and two 100/1000 Base-X SFP ports.The detailed Specification as follows. ; Preferred Make- Allied Telesis/Alcatel -Lucent/Juniper/Cisco

File system flash - 1 GB

RAM-1 GB

USB Port- 1 (type A, USB 2.0)

Console- 1 (RS232 RJ45)

IEEE 1588v2 capable ports- 12

MACsec capable ports-12

Operating temperature -10°C to 60°C (14°F to 140°F)

Storage temperature - -40°C to 85°C (-40°F to 185°F)

Humidity (operating & storage) - to 95% non-condensing

Altitude-13,000 ft

MTBF (Hours)- 1,298,328

Power Supply efficiency-85%

Acoustic (-10°C to 45°C) (dB)-Silent

Acoustic (45°C to 60°C) (dB)-56 dBA

System power consumption (idle)-8.5 W

System power consumption (full load)- 19 W

Heat dissipation (BTU- 64.8

PoE power budget 115 W

Switching capacity (aggregated-24 Gb/s

Forwarding capacity-17.9 Mb/s

Mac Address:16K or more VLAN: 4K or more System Policies: 1.5K or more Max Jumbo Frame: 9216 bytes Multicast Group: up to 1000

Auto QoS for switch management traffic,Policy-based QoS, Traffic Prioritization, Priority Queues: Eight hardware-based queues per port, SPQ, WRR

Static Routing, MSTP, RSTP, PVST+,IPv6 Tunneling, LACP, LAG, IGMPv3, DHCP, DHCP82,DHCP Relay for IPv4/IPv6,Multiple microcode image support with fallback recovery, ARP,SDN support through Restful API and openflow 1.3.1

Loopback IP address support for management per service, Policy- and port-based mirroring, Remote port mirroring, sFlow v5 and Remote Monitoring (RMON), Unidirectional Link Detection (UDLD),Digital Diagnostic Monitoring (DDM), LLDP-MED, NTP,MVRP, SNMP, sflow or equivalent

Dynamic change of authentication (CoA),MAC-based authentication for non-IEEE 802.1X hosts, MAC address lockdown, Prevention from ARP attacks, Web based Authentication, Autosensing IEEE 802.1X multi-client, multi-VLAN support,RFC 1321 MD5, RFC 2284 PPP EAP,RFC 1826/1827/4303/4305 Encapsulating Payload (ESP) and crypto algorithms, RFC 2104 HMAC Message Authentication, Built-in CPU protection against malicious attacks

Unified management, control and virtual chassis technology, Virtual Chassis 1+N redundant supervisor manager, Virtual Chassis In-Service Software Upgrade (ISSU),Smart continuous switching technology, IEEE 802.3ad/802.1AX Link Aggregation Control Protocol (LACP) and static LAG groups across modules

CE, EN 55032,24,35, RoHS, WEEE,REACH

US UL 60950, CSA22.2

EN 61000-3-2 & 3,EN 61000-3-2(all editions)

EN 60825-1/2 Laser

IEEE802.3: Hi-pot Test (2.25 KV DC on all Ethernet Ports)

SFP should be of same make as switch.

Vendor to be present in Gartner Magic Quadrant.

The Switch shall work with on-premise and cloud based NMS without change in hardware/software/OS Image.

Warranty-01 Years from OEM with Toll free number for support in India

SITC of Network managent solution in virtual mode on industry standard Server with AI ops monitoring tool. ; Preferred Make- Allied Telesis/Alcatel -Lucent/Juniper/Cisco

GENERAL

A Solution that shall include a client/server Network Management System that is WEB 2.0 based, providing a WEB GUI for different types of PCs, tablets and smartphones.

The NMS shall offer a single and consolidated interface for network deployment, troubleshooting, performance analysis and configuration operations.

The NMS shall offer northbound interface RESTful APIs for application interoperability

The NMS shall allow real-time monitoring and analysis of critical network performance indicators through visual and customizable widgets

The proposed solution should be premise based and should support seamless migration to cloud without change in hardware/firmware of the switch. This should be based on standard server (Physical/Virtual)

The centralized management function shall allow to display the physical topology of the network.

The centralized management function shall be able to handle wired equipment (switches) and wireless (Acces Point) management for a “unified management” approach.

The solution shall be able to automatically discover new Switch or APs added to the network.

The solution shall be able to blacklist a client, either manually or automatically after a client attack has been detected.

The centralized management function shall allow per equipment configuration and software backup and restore, and bulk backup and restore.

TOPOLOGY

The NMS shall build and present a visual topology for both logical and physical infrastructure with actual neighbor linkage info (IP subnet, layer 2, LLDP adjacency protocols) and live device status

The NMS shall present logical maps based on user-defined filters (IP subnet, location…).

NOTIFICATION MANAGER

The NMS shall allow monitoring and analyzing alerts, notifications and network performance from network equipment from any vendor

The NMS shall offer advanced alert capabilities through customizable filtering and sorting capabilities.

The NMS shall allow remediation and notifications actions based on predefined conditions with a single click

LOCATOR

The NMS shall be able to locate devices in the network based on MAC address or IP Address, irrespective whether the device is located on a fixed or wireless network.

RESSOURCE MANAGER

The NMS shall allow mass programmable equipment configuration by the mean of scripts.

The NMS shall allow infrastructure-wide software image update for baseline version management

UNIFIED ACCESS

The NMS shall offer a unified user interface for wired and wireless role profiles for user based access

The NMS shall offer a wired and wireless cohesive authentication configuration and end-user profile definition for appropriate network access rights and dynamic policies

ADDATIONAL FEATURES

The centralized management function shall allow access to all wIPS/wIDS features.

The centralized management function shall offer, on the basis of an application signature file, insight at application layer (e.g. facebook.com, youtube.com, salesforce.com…) even if the applications run on top of the HTTP or HTTPs protocols. It shall also allow control of those applications.

The solution should allow the admin to easily provision, manage and maintain a network infrastructure with alarms, unified access security policies

The solution should provide full visibility into wireless, devices and applications, as well as predictive analysis for forward planning

The management solution should act as comprehensive tools for infrastructure configuration, monitoring, security, device configuration, alert management, to accelerate, downtime resolution, and overall management.

It should be web based interface with customizable dash board

Provide details about problematic devices including temperature, memory etc

Monitor network bandwidth and end device traffic pattern

Provide top applications/users usage analytics real time and historical

Port utilisation details and threshhold limits

Provides threat mitigation through a secure perimeter against intrusion and malware attacks

Should support third party network devices for basic SNMP and report

SITC 01 Gigabit optical transceiver SFP. Supports monomode fiber over 1310nm wavelength nominal) with an LC connector. Preferred Make- Allied Telesis/Alcatel -Lucent/Juniper/Cisco

SITC of Video Management and enterprise server,Intel Xeon Silver 4410Y, 32 GB RAM, Redundant PSU, 2 NIC GIG, License for Microsoft Windows Server 2022 standard edi tion, 64 and Accesoories,Make Dell/HP/Lenevo, 3YR Pro Support Next Business Day Onsite, Preferred Make- DELL/HP/LENOVO

SITC of Video Management Operator Client System i9-13900/32GB/512 SSD + 1TB SATA/Win 11 Pro/No Monitor/DVDRW/5 yrs NBD/1000W / NVIDIAGeForce RTX™ 3070, 8 GB GDDR6, 3 DP, HDMI with 32 " Monitor; Preferred Make-Dell/HP/Lenevo

All the Switches, NMS, SFP Modules must be from the One OEM. Core to Access connectivity should be on 10G.

OEM Criteria for Passive Networking items.

OEM must provide declaration on conformity of all the passive components to the following standards: a) TIA/EIA 568-2.D ; b) TIA/EIA 568-3.D ; c) ISO/IEC 11801

OEM must be a member in the TIA and BICSI organization. OEM shall have RCDD certified manpower in India for design support and validation. Certificate is Mandatory

OEM should have valid ISO 9001 and ISO 14001 certificate on Design, development and manufacture of SW and HW solutions for communication networks.

All the products must have RoHS Compliance and from One OEM

6 Port LIU Switch : SITC of 6 Port Loaded LIU with SC Unit for 6 SM fiber Single Mode fibres OS2 (1 Nos. of Loaded Duplex adapter with Adapter plate) along with 1 Pc of Splice Tray - 6 Fiber Capacity & 6 Nos. of SC Pigtail - Pigtail 1 Meter SM Os2 (Make:Legrand/Molex/RIT/Siemon)

Detailed Specs for Fiber Optic LIU Rack Mount LIU (6 Ports)

Fiber optic patch panel : Fiber optic patch panel FMS Termination Drawer should have sufficient slots to accommodate 3 of 12/16 Port LC Adaptor Plates.

Should have Slide type drawer structure

Height: 1 U, 1.75 inches (12 & 24 Ports)

Material: Cold Rolled Steel in surface coated by electrostatic epoxy powder

Slots: FMS should have sufficient slots to accommodate adaptor plates

Empty Slots of FMS should be covered with blank plates.

Splice Tray : Splice Tray of ABS, Comply with UL 94V2 material should be supplied with LIU.

Detailed Specs for 6/12/16 Port LC/SC Type Adaptor Plates (SM OS2)

The adaptor plate should be pre-loaded with LC/SC Type Single ModeDuplex Adaptors.

Port Density :6/12/16 LC/SC Single mode Ports

All LC adapters should be duplex type with shutter for protection. Adapters should be snap mount for easy insertion and removal.

Insertion Loss: <0.2 to <0.1 dB

Compliance :RoHS Compliant

Detailed Specs for LC Type 9/125μm SM Fiber Optic Simplex Pigtail

Type : 9/125 micron fibre performance

Jacket Material : LSZH complying to IEC 61034-1 & 2,IEC-60332-1, IEC-60754-1 & 2

Operating Temperature: -40°C to +75°C

Connector Insertion Loss: 0.30dB(Max)

Attenuation: 1310/1550 : 0.36/0.22 dB/KM

SITC of 12 Port LIU Switch : SITC of 12 Port Loaded LIU with SC Unit for 12 SM fiber Single Mode fibres OS2 (1 Nos. of Loaded Duplex adapter with Adapter plate) along with 1 Pc of Splice Tray - 12Fiber Capacity & 12 Nos. of SC Pigtail - Pigtail 1 Meter SM Os2 (Make:Legrand/Molex/RIT/Siemon)

Detailed Specs for Fiber Optic LIU Rack Mount LIU (6 Ports)

Fiber optic patch panel : Fiber optic patch panel FMS Termination Drawer should have sufficient slots to accommodate 3 of 12/16 Port LC Adaptor Plates.

Should have Slide type drawer structure

Height: 1 U, 1.75 inches (12 & 24 Ports)

Material: Cold Rolled Steel in surface coated by electrostatic epoxy powder

Slots: FMS should have sufficient slots to accommodate adaptor plates

Empty Slots of FMS should be covered with blank plates.

Splice Tray : Splice Tray of ABS, Comply with UL 94V2 material should be supplied with LIU.

Detailed Specs for 6/12/16 Port LC/SC Type Adaptor Plates (SM OS2)

The adaptor plate should be pre-loaded with LC/SC Type Single ModeDuplex Adaptors.

Port Density :6/12/16 LC/SC Single mode Ports

All LC adapters should be duplex type with shutter for protection. Adapters should be snap mount for easy insertion and removal.

Insertion Loss: <0.2 to <0.1 dB

Compliance :RoHS Compliant

Detailed Specs for LC Type 9/125μm SM Fiber Optic Simplex Pigtail

Type : 9/125 micron fibre performance

Jacket Material : LSZH complying to IEC 61034-1 & 2,IEC-60332-1, IEC-60754-1 & 2

Operating Temperature: -40°C to +75°C

Connector Insertion Loss: 0.30dB(Max)

Attenuation: 1310/1550 : 0.36/0.22 dB/KM

SITC of Fiber Duplex Patch Cords SC-LC/SC-SC SM Patch Cord 2 mtr. (Make:Legrand/Molex/RIT/Siemon)

Detailed Specs for Patch Cord, LC SC, Duplex, SM, Bend Insensitive G651, PC, LSZH

Cable : LC/SC-SC/LC 9/125μm or 1310 μm SM Duplex Patch Cord Length : 2mtrs (as per requirement)

Connectors : The optical fiber patch leads shall comprise of Single Mode 9/125μm or 1310 μm fiber with 2XLC type fiber connectors terminated at one end of fiber patch cord and 2xSC type connector at other end of the fiber patch cord

Insertion loss should be better than ≤ 0.30 dB

Jacket Material : LSZH complying to IEC 61034-1 & 2,IEC-60332-1, IEC-60754-1 & 2

Attenuation: 50/1300 : 3.0/1.0 dB/KM

Connector Loss : 0.30dB(max)

Operating Temperature : -40°C to +75°C

Supply and laying of 6 core Single mode OS2 Loose tube Armoured Optical fiber cable through existing conduit: The Fiber should be OS2 Single Mode Optical Fiber Cable of Size 9/125µm. (Make:Legrand/Molex/RIT/Siemon)

Detailed Specs for Outdoor F/O Cable, Loose Tube, SM – 1x6 Fibers, Central Steel rod with CST, PE

The fiber should be optimized for operation at 1310 nm and at 1550 nm.

Should fulfill the requirements of ISO.IEC 11801 - 2nd Edition, type OS2, ITU-T REC G 652D spec IEC 60794-1-2 F5

Fibre Count : 6 /12

Fiber count per tube :6 / 12

Filler count :4

Filler Material : PP

Max. Attenuation: At 1310 nm <= 0.36 dB/km, At 1550 nm <=0.22 dB/km

Fibre/Tube Identification : Multi Tube

Fibre protection (Tubes) : Polybutylene Terephthalate (PBT)

Armouring : CST

Thickness : 1.6mm

Outer Sheath :UV Stabilised Polyethylene (PE)

Central Strength Member: Steel wire coated with PE

Water Blocking : Thixotropic Gel (Tube);

Petroleum Jelly (Interstices)

Cable Diameter (D) : 9.0 ± 0.5 mm

Mass (Nominal) : 91 kg/km

Min. Bending Radius (during Installation) : 20 D;D-Outer Diameter

Max. Tensile Strength-Short Term : 1500N

Max. Crush Resistance-Short Term : 2200N/100 mm

Operating Temperature range : -40°C to +70°C

Approved Make : Molex / RIT / SIEMON

All the cable and accessories are from the same OEM

SITC of Cat6 Shielded Field Termination Plug with Following Specifications (Make:Legrand/Molex/RIT/Siemon)

Standardization: Compliant with Cat.6, Class EA requirements: ISO/IEC 11801 2nd Edition backward Compliant with Cat.6 component standards IEC 60603-7-4 and 60603-7-5

Cable: UTP/STP

Number of conductors : 8

Termination: IDC type Tool less

RJ45 Plug Metal covers: Zinc die-casting with nickel plated

RJ45 Plug contacts: Phosphor bronze with nickel plated

Plastic Wire Organizer: PC, Color: White, UL 94V-0

IDC Durability: ≥20 Termination cycles

RJ45 Jack Durability: ≥750 Plug-Jack mating cycles per IEC 60603-7-81

Operating Temperature: -10 degree C to +60 degree C

Patch Cord retention strength: 7.7 Kg Max. according to IEC 60603-7-5

Rj45 Plug Insertion force: 3.1 Kg Max according to IEC 60603-7-81

Splicing of Armoured SM/MM Fibre Optics Cable: Splicing, testing and commissioning of supplied, OFC cable of 6-Core Armoured Fibre Optics

Providing, fixing, fitting, installation and testing of 42 U Network Rack as server cabinet 19" LCS2 along with all standard accessories, 800mm (W), 1000mm (D), CRCA 'D' grade 1.6mm thick sheet, pwoder coated for cabinet , 4mm Toughened Tinted Glass Door and along with following accessories:- 1. Cooling fan 220/230V AC, of 90 CFM-- 4 Nos. , 2. Cable manager Metal 4 Nos. 3. PDU- 230V /AC 1 No., 6. Mounting Hardware (20 Sets of M-6 screws, washers, cage, nuts (Nickle Coated)- 3 Nos. ,7. Earthing strips copper 150mm H 1 No. 8. Door Lock 1 No. ,9. Caster Wheels (with breake) 2 Nos. 10. Caster Wheels (without breake) 2 Nos. ,11. Front Metal Band 1 No. (Preferred Make-Valrack/President/Rittal/Netrack

SITC of 6 U Pole Mounted Outdoor Rack:19” Wall mount 6U 600W/500D IP55 protection Cabinet CRCA sheet, Top cover with (2)fan and filter. bottom cover with gland for cable entry(1), rain canopy(1) Front metal doors equipped with hood & IP55 filter for IP55 compatible cabinets,19” uprights facilitate in mounting of the 19” equipment. The mounting distance is in accordance with the standard DIN 41494, STANDARDS IEC 60529 : 2013 (NF C 20-010) Degrees of protection provided by enclosures (IP code) Permissible load bearing capacity - Upto 70 Kg,Corrosion Resistance Salt spray test according to ISO 9227 (NSS test) and IEC EN 60068-2-11 (Ka test) for 168 hours: degree of Rusting Ri1 according to ISO 4628-3, propagation ≤1 mm according to ISO 4628-8.Pure polyester powder coating paint applied by electrostatic dusting. Enclosures comes in one color. All components- RAL 7035 Pastel structure color . The rack should contain the follwing- One Metal Cable Manager - 01U - Plastic Cable Loop's Mountable - Black Fine Tex,One Cantiliver Tray - 01U - 255D - Pastal Fine Tex.One Packet Mounting Hardware Packet { Containg 1 Nos Each Of 3 } - 20 Set ,Power Distribution Unit - 06/13 Amp Multi-Standard - 06 Socket - Single Pole / Screw Mountable / 06 Amp MCB / Alternating Current - 06 Amp 3 Pin Plug with Power Cable 0.75 sq.mm 3 meter Length - Black Fine Tex. - Assembly– 1 No.; Preffered Make-MTS/Valrack/President

SITC of single Run Outdoor Cat 6 Cable(Category 6 4 Pair U/UTP cable. A HDPE compound insulates the cores with a IEC 60332-1 complied LS0Hn Category 6 compliant LS0H inner sheath and FR PVC outer UV resistantn Suitable for outdoor Installations n Compliant to TIA/EIA-568-C.2 Supports ultra hi-speed data net works such as Gigabit Ethernet (1000 Base-T and 1000 Base-TX) and beyondn Incorporates central spine maintaining pair separationduring installation to ensure installation); (Make:Legrand/Molex/RIT/Siemon)

SITC of 9 Mtr. MS Swaged Pole alongwith Mounting Arrangement with ISI Standard; Preffred Make- SK Poles/Bajaj/Standard

SITC of 32 MM OD and 25 MM ID HDPE Pipe with ISI Mark; Prefered Make- Sree/Mahavir/Modi

SITC of 3 Core 2.5 sq.mm Armored Copper Power Cable; Prefered Make-Polycab/Finolex/Havells

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C"curve, miniature circuit breaker suitable for inductive load of following poles with MCB DB complete withconnections, testing and commissioning etc. as required.Prefered Make-Legrand/ABB/L&T

SITC of Single Phase Online 02 KVA UPS Preffered Make-Delta/EATON/Numeric/BPE

SITC of 42 AH SMF Battery, with 24 months replacement

VRLA- AGM maintenance -free

SITC of MS Battery Rack suitable for 15 to 20 UPS Battery installation

Chemical Earthing

Supply, errection, fitting, fixing, commissioning and testing along with earth cutting, digging, earth refilling for chemical earthing of the building except G.I. Strips (25mmX5mm) Each earth pit has to be tested with earth tester 1000 V/1000 Ohms & the test report has to be submitted by the contractor to the department after certification of the same by the consultant. The above chemical earthing includes the provision of masonary enclosure and HDPE Earth Pit Cover 300mm X 300 mm (Under-floor earth inspection pit) having locking arrangement as earth chamber.The above chemical earthing includes the following items (3 Mtr Earthing)

Each chemical earthing shall have following details:-

Supply of Pollution free Earthcon Compound 4 bags of 25 Kg each

Supply of 17.2 mm dia, 250 micron,molecularly bounded copper coated 3 Mtr long electrode. Tested as per IEC 62561-2. Meets the requirement of IS 3043 & IEC 60364-5-54. Tested for short circuit withstanding capacity. High Tensile strength. (UL Listed).

Supply of Stainless Steel "U" Bolt Clamp

Supply of HDPE Earth Pit Cover for earth chamber (Capacity of 5 ton)

Sub-total-B( UPS System & Accessories)

SITC of 5MP Bullet camera with 1/2.7‑inch CMOS, 3.5-10mm (+-1mm) AVF Lens, Effective pixels 2,592 x 1,944, 30 fps sensitivity – (Measured according to IEC 62676 Part 5 (Color 0.14 lx, 120 dB Dynamic range,Electronic Day/Night, Automatic Electronic Shutter (AES), H.265, H.264 MP (Main Profile); M-JPEG Video compression,White balance, Backlight Compensation, Privacy Mask,Rule based alarms and tracking, Object in field; Line crossing; Enter / leave field; Loitering; Follow route; Counting; Occu pancy; Condition change; Similarity search; Objects stopping or starting to move. 2D tracking based on Duration, Size, Aspect ratio v/h, Direction, Color, AI based Object classes (Upright persons,vehicle),, MicroSD card slot for edge recording, Motion, tamper detection, FTP, Dropbox and e-mail applications, ONVIF Profile S, G,T & M. PoE, CE, FCC, UL certified. SD card support up to 2TB,IP66,IK10, Built in 30 Mtrs IR. Built in TPM, RSA 4096 bit; AES/CBC 256 bit, TLS 1.3, UL Cap/FIPS 140, NDAA Compliant, BIS. Preffered Make- BOSCH

SITC of 5MP Outdoor Bullet camera with 1/2.7 inch CMOS, Effective pixels 2592 × 1944, 30fps, Sensitivity – (Measured according to IEC 62676 Part 5 Color 0.044 lx Mono 0.010lx With IR 0.0 lx, 120 dB Dynamic range, Electronic Day/Night, Automatic Electronic Shutter (AES), H.265, H.264 MP (Main Profile); M-JPEG Video compression, White balance, Backlight Compensation, Privacy Mask,Rule based alarms and tracking, Line crossing, Enter /leave field, Follow route, Loitering, Idle / removed object, People counting, Crowd density estimation, Object classes (Upright persons, Vehicles) detect up to 64 objects simulataneously, Audio detection (if microphone used), 3.5-10mm (+-1mm) Automatic Varifocal (AVF) lens, MicroSD card slot for edge recording, Motion, tamper and audio detection, FTP, IR range upto 60mtrs, ONVIF Profile S ,G,T& M , PoE, IP66,IP67,and NEMA 4X, IK10, CE, FCC , UL certified. SD card support up to 2TB. Built in TPM, RSA 4096 bit; AES/CBC 256 bit, TLS 1.3, UL Cap/FIPS 140, NDAA Compliant, BIS. Preffered Make- BOSCH

SITC of 4MP Outdoor ANPR Bullet camera with 1/1.8 inch CMOS, Effective pixels 2688(H) x 1520(V), 60fps, Sensitivity – (Measured according to IEC 62676 Part 5 Color 0.078 lx Mono 0.0011lx With IR 0.0 lx, 141 dB Dynamic range, Electronic Day/Night, Automatic Electronic Shutter (AES), H.265, H.264 MP (Main Profile); M-JPEG Video compression, White balance, Backlight Compensation, Privacy Mask,Rule based alarms and tracking, Line crossing, Vehicles Detection up to 64 at a time,10.5 mm – 45 mm ( + - 2 mm) Automatic Varifocal (PiRIS) lens, MicroSD card slot for edge recording, Motion, tamper and audio detection, FTP, IR range upto 140mtrs, ONVIF Profile S ,G,T& M , PoE, IP66,IP67,IP6K9K and NEMA 4X, IK10, CE, FCC , UL certified. SD card support up to 2TB. Built in TPM, RSA 4096 bit; AES/CBC 256 bit, TLS 1.3, UL Cap/FIPS 140, NDAA Compliant, BIS. Preffered Make- BOSCH

SITC of AI-Neural Networks based 3D PeopleTracking Video Analytics Software for Vehicle monitoring and guidance. Can detect Vehicle Started moving and Stop. Classification of Car, Bus, Truck, Motorcycle, Bicycle and parking assistance. Software can intelligently adapt to challenging situations like lighting differences or environmental conditions, such as rain, snow, clouds, blowing leaves, and shaking cameras and automatically reduce false alarms that way. Preffered Make- BOSCH

Supply, Installation, Testing and Commissioning of Video Managemet software with Seamless management of digital video, audio, and data across IP network. Support of central monitoring/control/playback of cameras from different locations. Alarm management, Users management, recording quality management, Schedule recording, Drag & drop ,Bookmarks,snapshot, Pop-up alarm, site maps support, virtual matrix functaionality, Live & playback video, export, logbook, sequencing, GPU Decoding, LDAP Support, Up to 4 monitors support on a single Workstation, Dual-authorization logon, Email or SMS notification on alarm, Support for 3rd party cameras via RTSP, HTTP, MJPEG, ONVIF Profile S or better. Live Map support for camera plotting, Object Tracking support on multiple camera over Live Map, Complete system with 500 Device Licese including mandatory native N:N Recording Failover support. VMS shall seemlessly incorporate existing VMS, STORAGE and Client System to built up Centralize operation. Comprehensive Software Maintenance ( Existing + New Requirement) for 3 Year. Preffered Make- BOSCH

SITC of NAS/SAN with RAID5 & RAID 6 configurable Storage Appliance for 30 Days of Recording for Newly required Cameras video & Metadata. Intel® Core™ i7-12700E or higher including 25 MB Intel® Smart Cache and Installed memory of 16 GB DDR5-4800 1Rx16 ECC , UDIMM. DUAL Redundant Power Supply, Rack Mount 3 U. 288 TB Gross Storage Support. Minimum 16 Hard Disk Slots with support of 18 TB per Slot.The Hardware includes System drive 2x SATA3 2.5' 480 GB Enterprise SSD, RAID1 configuration . Onboard graphics Intel® UHD Graphics 770 , 12 Gb/s Sixteen-Port SAS RAID Card , Shall include Microsoft Windows Server IoT 2022 for Storage Standard. Certifications UL,CE,FCC,NDAA,BIS. FIPS 140. Discreet TPM 2.0 Preffered Make- BOSCH

SITC of Enterprise Grade Hard Disk, SATA-III, 18 TB , 7200 RPM for 30 Days Back up; Make-Seagate/WD

Add 18 % GST

Add 1% Labour Cess

Sanjay Sharan (BID ID -675276)