JOINT FILLING OF RUNWAY AND TAXI TRACK AND OTHER B/R WORK IN 665 AND 201 ARMY AVN SQN AREA UNDER GE NASIK ROAD.

Amount

M&L for Raking out existing construction joints/dummy joints 10mm wide X 25mm deep in concrete pavements, cleaning surfaces and sweeping to make the surface free from dust/dirt with air compressor/blower and reoving debris to a distance exceeding 200m form edge of pavement for disposal in low lying areas.

M&L for Raking out existing expansion joints 20mm wide X 25mm deep in concrete pavements, cleaning surfaces and sweeping to make the surface free from dust/dirt with air compressor/blower and reoving debris to a distance exceeding 200m form edge of pavement for disposal in low lying areas.

M&L for Filling construction joints/ dummy joints 10mm wide X 25mm deep in concrete pavements with sealing compound Grade ‘B’ after applying primer to the sides of jopints as per manufacturer's instructions.

M&L for Filling expansion joints 20mm wide X 25mm deep in concrete pavements with sealing compound Grade ‘B’ after applying primer to the sides of jopints as per manufacturer's instructions.

M&L for Painting lines, dashes, arrows, letters, and painting dispersal area etc. on roads, concrete pavements and the like exc 10cm wide with two coat of water based paint, white or golden yellow including preparation of new or previously treated surfaces to receive the painting. (Painting shall stand out boldly and solidly without showing signs of brush marks or surface underneath. If necessary, the surface shall be repainted by one or more coats until the desired result is obtained.)

Dismantling asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings.

Dismantling wrought iron or mild steel work of any description such as purlins ofor roof and window guard bars.

S&F steel work in tubular or rectangular hollow section in rafters, purlins etc. and connected works complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240

M&L for Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M&L for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S&F 2mm thick Fibre glass reinforced translucent reinforced corrugated sheeting with two corrugations side lap fixed with coach screw and washers in roof wall etc complete all as specified and as directed.

M&L for Preperation of new untreated steel or iron surfaces of any description over 10cm girth or width, not otherwise described and two coats of synthetic enemel paint over a coat of red oxide, zinc chrome primer.

Taking down aluminium door shutters of any description.

Taking down aluminium window shutters of any description.

Taking down aluminium door and window frame of any description.

S&F Aluminium (minimum 50 micron powder coated) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified.

S&F Aluminium (minimum 50 micron powder coated) door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified.

S&F Aluminium (minimum 50 micron powder coated) window and ventilator shutters, side hung/sliding type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.) hinges type B-21, 100mm long (2 Nos.), suitable handle (1 No.), rollers, grip etc. complete all as specified

S&F 5.5mm thick sheet glass plain or tinted, ordinary quality, fixed in aluminium doors and windows.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staple or fixed in alumionium frames.

S&F Floor door closer hydraulically regulated, universal type (cast iron body) suitable for aluminium door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed

M&L for Preparation of old or previously treated steel or iron surfaces of any description over 10cm width or girth and two coats of aluminium paint over a coat of red oxide primer.

Demolition of cement concrete in ground floors and pavings n exc 15cm thickness (below or above ground level).

S&F 75 mm thick cement concrete 1:4:8 type D2 (40 mm graded aggregate) in sub floor.

M&L 40mm thk Cement concrete type B-1, 1:2:4 (20mm graded aggregate)

M&L for for screed bed or bedding layer20mm thick in cm 1:6 for laying floor finishes complete all as specified and directed by Engr-in-Charge.

M&L for for rough shahabad stone 25mm to 30mm thick in flooring /plinth set and jointed in neat cement slurry and pointed in cm 1:4 complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specially provided for.

M&L for Providing cement concrete 1:2:4 type B0 (12.5 mm graded aggregate) in roof kerb or mud stops, rounded or chamfered on edges.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

M&L for Vitrified Ceramic tiles (Superior quality) 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick cement mortar screed bed in cement mortar 1:6, set and jointed in neat cement slurry and pointed in coloured cement to match.

M&L for Vitrified Ceramic tiles (Superior quality) 10 mm thick (square/ rectangular) polished in skirting etc. cut out of tiles of area not exceeding 0.36 sqm, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 10mm thick cement mortar rendering in cement mortar 1:4, set and jointed in neat cement slurry and pointed in coloured cement to match.

M&L for Non Skid ceramic tiles coloured 7 to 8 mm thick (square/rectangular) area of each tile exc 0.06 sqm but not exc 0.11 sqm , in floors etc. including 15mmm thick cement mortar screed bed in cement mortar 1:6,set and jointed in neat cement slurry and pointed in white or coloured cement to match

M&L for Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick including 15mm thick cement mortar rendering in cement mortar 1:4 set and jointed in neat cement slurry and pointed in white or colour cement to match

Demolition of cement concrete of any description and in any position not otherwise specifically provided.

M&L for Cement concrete type C2 1:3:6 (using 40mm graded stone Aggregate) in foundation of manholes.

M & L for cement concrete 1:3:6 type C1 using 20 mm graded stone agregate in coping benching or similar work finish even & smooth all as specified and directed.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar.

M&L for Brickwork with flyash bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.

M&L for Rendering 15mm thick in cement mortar 1:4 on faces of brick work finished fair and even.

M&L for Rendering 15mm thick in cement mortar 1:6 on faces of brick work finished fair and even.

M&L preparation of newly plastered surfaces and applying two coat of cement base paint on wall complete all as specified and directed.

M&L for Extra for forming fair finished drain or channel upto 45cm inner girth in cement concrete, usingex-tra cement, including forms, moulds, mi-tred/stopped ends etc.

M&L for Machine pressed precast conctete interlocking paver block with grey cement and pigment with rubber moulded glossy finished surface, any shape and size confirming to IS 15658-2006 of 60 mm thickness M-30 grade laid over and including 30 mm thick stone dust cushion.

Eacavation in trenches n.exc 1.5 M in wdith & n.exc 1.5 M in depth for foundation & getting out in soft/loose soil all as specified and directed.

Returning, filling in soil incl. Spreading,leveling,watering and well ramming in layers n.exc 25 cm all as specified & directed.

Removing excavated materials (soil) exc 500 M but n.exc 1.5 KM and deposited where directed at a level n.exc 1.5 M above the starting point all as specified and directed.

Demolition and breaking up drain pipes 150mm dia (salt glazed ware or reinforced concrete) set in cement mortar all as specified and directed.

Demolition and breaking up drain pipes 200mm dia (salt glazed ware or reinforced concrete) set in cement mortar all as specified and directed.

M&L for reinforced concrete pipe class NP2, laid and joined complete with collars 150mm bore of pipe.

Demolition of reinforced cement concrete(reinforcement cut as reqd to facilitate demolition) in ground floor and paving as in manhole covers n.exc 15 CM thickness(below or above GL) as specified & directed.

M&L for Providing precast cement concrete type B-1, 1:2:4 (using 20 mm graded aggregate) in landings, cover slabs (for drains and manholes etc.) set in cement mortar 1:6.

M&L for Mild TMT steel bars 6 to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

NOTE : - AMOUNT OF SCHEDULE OF CREDIT RS. 30,950.00 WILL BE DEDUCTED FROM TOTAL AMOUNT OF BOQ.

Vinod Enterprises

Alpha Construction

M/S K. K. Construction

SVT ENGINEERS AND CONTRACTOR.

Bidder Name

M/S SAMEER SUBHASH PATANI

SVT ENGINEERS AND CONTRACTOR.

M/S K. K. Construction

Alpha Construction

Vinod Enterprises