GE/PNH-57/2019-20

Amount

Schedule 'A'Part-I (Building Work)

Total amount of Sch 'A' Part I (Building work)

Schedule 'A'Part-II (INTERNAL WATER SUPPLY & PLUMBING WORKS)

Total amount of Sch 'A' Part II (Internal water supply & plumbing Works)

Schedule 'A' Part-III ( INTERNAL ELECTRIFICATION WORKS)

Total amount of Sch 'A'Part III (Internal electrification Works)

Schedule 'A' Part-IV (SITE CLEARENCE WORK)

Total amount of Sch 'A' Part IV (Site clearence Work)

Schedule 'A'Part-V (PATH WORKS)

Total amount of Sch 'A' Part V (Path Works)

Schedule 'A'Part-VI (AREA DRAINAGE WORK)

Total amount of Sch 'A' Part -VI (Area drainage work)

Schedule 'A'Part-VII (SEWAGE DISPOSAL WORK )

Total amount of Sch 'A' Part-VII (Sewage disposal work)

Schedule 'A'Part-VIII (EXTERNAL WATER SUPPLY WORKS )

Total amount of Sch 'A' Part-VIII (External water supply work)

Schedule 'A'Part-IX (EXTERNAL ELECTRIFICATION WORKS )

Total amount of Sch 'A' Part-IX (External electrificationwork)

Schedule 'A'Part-X (HOT WATER SUPPLY WORKS )

Total amount of Sch 'A' Part-X (Hot water supply work)

Schedule 'A' Part-XI (Misc Items of Works)

4mm thick pressure stream cured vairant E-board designer pattern (IS: 14862-2000) in ceiling fixed with screw as per manufacturer's instructions, fixed with white powder coated galvanized iron grid with 24mm wide T-section exposed flanges comprising of main runner made from 0.33mm thick galvanised steel sheet & of size T 24x32mm and spaced at 1.2m c/c securely fixed to the structural soffits by hangers at 1.2m of GI wire 4mm dia fixed with rawl plug, level adjusters and screws etc.The last hanger at the end of each main runner shall not be more than 450 mm from adjacent wall flush fitting of 1200mm long cross tee with (double stitching) to be inter locked between main runners at 600mm c/c to from 600x600mm modules, angle along perimeter wall shall be of 0.45mm thick galvanized steel of size 19x19mm of white colour, fixed as in repairs, complete all as specified and directed. Make: Everest Industries Ltd or of equivalent approved make as approved by GE.

Demolition of cement concrete in ground floors and paving (unreinforced) n exc. 15 cm thick, (below or above ground level), complete all as specified and directed.

25mm thick PCC (1:2:4) type B-0 (using 12.5 mm graded crushed stone aggregates) as in base in flooring, finished even and rough to receive the top layers complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

20 - 25mm thick machine cut kota stone slab of size 600x600mm as in flooring over and including 20mm thick cement screed in cement mortar (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab incl rubbing and mirror polishing ,complete all as specified and as directed.

Kota stone slab 18-20mm thick in riser or steps, skirting, dado and pillar laid over and including 10 mm thick rendering in cement screed (1:4) and jointed with grey cement slurry mixed with pigment to match the shade fo the slab including rubbing and polishing complete all as specified and as directed.

50 mm thick PCC (1:3:6), type C-1 (using 20 mm graded crushed stone aggregagtes) as in plinth protection, finished even & smooth without using extra cement complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting any gauge, thickness, including naintal or similar pattern roof covering complete all as specified and directed.

Dismantling of asbestos cement sheets (corrugated, semi corrugated, etc ) as in roof covering complete all as specified and directed.

0.63 mm thick CGI sheeting with nominal grade of zinc coating 120 gms per sqm with two corrugation side lap fixed with 'J' or 'L ' hooks as in roof covering, walls etc complete all as specified and as directed. Make : SAIL/TATA/JSW STEEL

All as per item No 31 above but except sheeting

0.80 mm thick plain galvanised mild steel sheeting in ridges, hips, valley gutters drop and straight flashing (length and girth as fixed) of class-3 ,complete all as specified and as directed. Make : SAIL/TATA/JSW STEEL

Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with & including L-type or J- type or cranked hooks or screw etc complete all as specified & directed.

Pre- painted galvalume aluminium zinc coating GI based plain steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed including L-type or J- type or cranked hooks or screw etc complete all as specified & directed.

Preparation of new or previously untreated steel or iron surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red-oxide primer complete all as specified and as directed.

Preparation of old painted surfaces of steel or iron as in CGI sheet roofing of any description, over 10 cm width or girth and applying one coat of synthetic enamel paint ,complete all as specified and as directed.

Preparation of old plastered surfaces of wall and applying one coat of oil bound distemper,complete all as specified and as directed.

Preparing old plastered or concrete surfaces of wall and applying one coat of cement based paint , complete all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from matel frame including punching or drilling out old glazing pins/spribng clips and providing and fixing new onces complete all as specified and as directed.

3 mm thick sheet glass ordinary quality and glazing with oil putty in square not exc. 0.5 sqm in each pane, complete all as specified and as directed.

Taking down shutter exc 2 sqm and removing from site complete all as directed.

35 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and directed.

30 mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (with sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (b); supplied and fitted to chowkats using second class hard wood complete all as specified and directed.

40 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and directed.

Preparing of new or previously untreated surfaces of wood of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

Butt hinges 100mm long, medium weight, cold rolled mild steel, and fixed ,complete all as specified and as directed.

Butt hinges 75mm long, medium weight, cold rolled mild steel, and fixed ,complete all as specified and as directed.

Aluminium anodised sliding door bolts with hasp and staple ( bolt type) and fixing clips of sheet, cast or extruded section and fixing botls and sliding both of extruded sections of cast alu alloy 300 mm long, complete all as specified and as directed.

Cutting holes into or through stone walls exc half brick but not exceeding one brick built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required complete all as specified and as directed.

Aluminium handle 150mm long, cast type, anodised fixed with steel screws complete all as specified and directed.

Aluminium handle 100mm long, cast type, anodised fixed with steel screws complete all as specified and directed.

Aluminium anodised barrel tower bolts of extruded section of 150mm size fixed complete all as specified and directed.

Aluminium anodised barrel tower bolts of extruded section of 75mm size fixed complete all as specified and directed.

Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, overall length of cover plate 140mm complete all as specified and directed.

100mm thick Plain cement concrete 1:4:8, type D-2, using 40mm graded crushed stone aggregate as in sub base complete all as specified and directed.

Chequered cement concrete tiles with chemical resistant coating of size 30cmx30cmx2.5cm thick machine pressed laid in floors/Path etc. set and jointed with neat cement slurry and pointed with coloured cement to match over & including 20 mm thick screed bed or bedding layer of mortar in CM 1:4, complete all as specified and as directed.

Providing, cement concrete type B-1 using 20mm graded aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

15 mm thick rendering in cement mortar 1:4 on fair faces of brick work or stone masonary, surface finished even & smooth without using extra cement complete all as specified and directed .

Preparation of new plastered wall surfaces and brought to a perfectly even surfaces by applying 3mm thick wall putty by suitable steel sheet allowing it to dry completely, rubbing with the abrasive paper and after then applying two coats of distemper oil emulsion , complete all as specified and as directed.

Preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of alkali resistance priming paint, complete all as specified and directed.

Keyed pointing to random rubble masonry, uncoursed or brought upto courses in cement mortar 1:3 complete all as specified and directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position framed work complete all as specified and directed.

Joint, channel, angle or tee section, fixed independently without connecting plates etc, including welding as necessary conforming to Fe-290 Gde E-165 Complete all as specified and directed.

Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, clits etc including welding as necessary conforming to Fe-290 Gge E-165 Complete all as specified and directed.

Mild steel work as in hold fast, wind ties for roof including securing bolts including all necessary drilling, bolting or reverting etc and all similar work conforming to Fe-290 (Gde E-165) complete all as specified and directed.

Mild steel work conforming to Fe-290 Gde E-165 in wind ties for roof including cutting top to shape as directed, drilling holes and fixed with L or J type cranked hook bolts all as complete.

Taking down chowkhat or frame not exc 1.5 Sqm each with shutters (without taking of shutter from the frames ) complete all as specified and directed.

Taking down chowkhat or frame exc 1.5 Sqm but not exc 4 Sqm each with shutters (without taking of shutter from the frames ) complete all as specified and directed.

Pressed steel frames of size 105x60 mm for door with one or more rebates incl necessary fittings, lugs, hinges, lock strike plate, flat iron hold fast etc, complete all as specified and as directed.

Second class hard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Walling of random rubble stone masonary, coursed, well bonded, bedded and solidly hearted, built in CM 1:6. complete all as specified and as directed.

Taking down carefully unserviceable copper/aluminium point wiring of any description including all fittings (switch , socket, switch socket combination, lamp holder, ceiling rose, regulator etc.) and making good disturbed surfaces of wall, floor etc. to match with existing finishes complete all as specified and as directed.

Point wiring with two single core, 1.5 Sqmm (nominal area) size multistranded copper conductor cable and one single core 1.5 sqmm (nominal area) size copper conductor cable, as earth continuity conductor connected to common earth dolly,1100 volts grade , FRLS, PVC insulated unsheathed cable in and including PVC casing capping of suitable size with PVC boards of appropriate sizes and all requisite accessories such as PVC elbow, Tee, Collers, Bend, PVC Conduits for crossisng etc. complete with PVC terminals box for mounting switches, sockets, fan regulators etc for the followings:- One light point controlled by one switch

One fan point (Ceiling and Exhaust) controlled by one switch

One 5 pin, 6 A socket outlet on the same board

One 5 pin, 6 A socket outlet on the independent board.

All as per item No 76.00 here-in-before but with two 2.5 sqmm size cables as phase and neutral and one 1.5 sqmm size cable as earth continuity conductor for one 15/20 Amps socket outlet independent -ditto-

Switch piano, flush type single pole one way 6 Amp ISI Marked. Make : Cona/Havells/Anchor

Ceiling rose, 3 terminal PVC/Polycarbonate, isolated body ISI Marked. Make : Cona/Havells/Anchor

Piano type switch, 1 way, 16 Amps, flush type, ISI marked, complete all as specified and as directed.

Switch socket 3 & 5 pin, 6 Amps, flush type, ISI marked, complete all as specified and as directed.

Switch socket 2 in 1, 6 pin, 6 and 16 Amps, flush type, ISI marked, complete all as specified and as directed.

Step type electronic fan regulator, flush type on the existing phenolic laminated sheet, etc. as required. Make : Cona/Havells/Anchor

Taking down ceiling / exhaust fan and re-fixing including making connections and providing wire of suitable size from ceiling rose complete all as specified and as directed.

LED light fitting, Single tube, 1 x 20 w LED, T8, 230 V (power factor not less than 0.90) box type, CRCA body, bipin holders connector block, etc. complete with all accesssories internally pre-wired, including LED lamp T8 20 W with aluminium heat shrink and connecting up with PVC insulated and sheathed 1100 volts grade, flexible, multistranded 1.0 sq mm copper conductor three core cable, fixed as in repairs, complete all as specified & directed. MAKE: CG cat Part No. DIJB12LT8-20 for fitting & LTT 8-20 watt or equivalent in Philips/Havells.

Street light fitting 25 watt LED, IP-65 protection, single piece pressure die cast aluminium housing high grade powder coated finish with heat resistant toughned clear cover for lamp and contorl gear compartment with high voltage surge protection device up to 5 KV, prewired including 1.60 mtr. Long 40 mm bore light gade GI pipe mounting bracket made to shape with and including MS clamp of FI 40mmx6mm size with bolts, nuts & washers and connecting to fitting with 3 core 1.5 sqmm PVC insulated cable, fixed as in repairs complete all as specified. Make: Cat part No. LSTP-25-CDL of CG or equivalent in Philips/bajaj.

Sheet Metal enclosure for SPN DBs, 8 Ways, Double Door (IP-43), built- in bus bars complete suitable for 240 Volts, AC, 50 Hz, fixed as in repairs complete all as specified and as directed Make: Legrand (Cat No 607711)or equivalent in Schneider/L&T/Havells

All as per Serial Item No. 87 above but 6 Ways

MCBs, SPN, 240 volts, breaking capacity 10 KA, rating 6-32 amps, Ç'series, complete all as specified and as directed. Make: Legrand /Schneider/L&T/Havells

MCB, SP,240 volts, breaking capacity 10 KA, rating 6 to 32 amps, complete all as specified and as directed. Make: Legrand (Cat No 603237)or equivalent in Schneider/L&T/Havells

1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheated in service connection suspended by insulating hangers not more than 1 mtr apart including 4 mm suspension wire, one twin core cable flat or circular of size 16 sqmm 2 core, fixed as in repairs complete all as specified and as directed.

House service bracket (Hook type) complete with 3.00 metre long GI pipe 40mm dia medium grade, 02 Nos bends, mild steel hook and stay, fixed as in repairs complete all as specified and as directed.

Earthing complete with galvanized Steel earth plate electrode 600 x 600 x 6.0 mm thick, buried directly in ground (earth pit not less than 2.25 meters below normal ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level surrounded from all sides by mixture of charcoal and common salt and electrode connected to and incl galvanized earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel and earth wire protected by GI protection pipe light grade 15mm dia connected to main earth wire on pole or controll board GI pipe light grade 20mm bore for watering funnel with wire mesh PCC chamber pit in PCC 1:3:6 type C-1 40mm yhick Precast RCC -25 cover reincorced with 8 mm dia TMT bars @ 10 cm C/C on both sides and handle, excavation and earth work in any type of soil and removal upto 50m complete all as sprecified and shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion.

Heavy duty exhaust fans with Turbo force of 1400 RPM ,single phase of sweep 300 mm, 230V, 50 HZ with all its accessories i.e. louvers, nuts, bolts, washers etc. including makingopening in wall of required size, grouting holes for fixing bolts and making good disturbed surfaces of wall and Including plastering & Painting of wall as per existing all as specified and directed.Make :Havells / khaitan /CG.

Dome type angle holder made out of polycarbonate with metal lamp holder ISI marked with back plate fixed on PVC square block with LED 9 watt fixed as in repairs complete all as specified and as directed.

Supply, fixing, commissioning & testing geyser of capacity 25 ltrs, star rated, ISI marked, storage type, with suitable fixing arrangement i.e nuts, bolts, washers etc, including grouting holes in brick or stone masonary, making good the disturbed surfaces and matching with existing surface and finishing complete all as directed. Make: Havells model Monza DX, Cat Part No. GHWAMTWH025 or equivalent of Crompton Greaves or Bajaj.

PVC connection, heavy duty, nylon braided, suitable for hot water, with brass alloy chromium plated nuts and nylon washers complete of size15mm dia x 450 mm long complete all as specified and directed.

Chromium plated, brass, horizontal/vertical, non return valve of size 15mm dia bore, ISI marked, on inlet side of geyser complete all as specified and directed.

Deduct Schedule of credit demolished/dismantled materials Rs (-) 47,923.80 (Minus) as listed in Schedule of credit.

RAJINDER VAID

M/S SAIN CONTRACTORS