Vellore District,Upgradation / Strengthening Of CJA Road To Thellai Road In Kaniyambadi Block ( Km 0/0 -6/450) Kaniyambadi Block NABARD RIDF XXIX 2023-24

Amount

Vellore District,Upgradation / Strengthening Of CJA Road To Thellai Road In Kaniyambadi Block ( Km 0/0 -6/450) Kaniyambadi Block NABARD RIDF XXIX 2023-24

Clearing and Grubbing Road Land Clearing the scrub jungles including cutting the scrubs and removing away from site etc complete

Excavation in Soil using Hydralic Excavator and Tippers with disposal upto 1000m for roadwork in soil and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross-sections, and transporting to the embankment location with a lift upto 1.5 m and lead upto 1000 m as per Tecnical Specification Clause 302.3

Filling Using Carted Earth Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 1000 m as per Tecnical Specification Clause 303.1

Gravel Shoulder Collectiona and supply of gritty gravel from appd quarry including cost and conveyance of all materials to site including all labour charges for spreading and compaction with power roller etc.complete, for SHOULDERS

Granular Subbase -Gr.III (Table 400.1) Construction of Granular Sub base Grade III by providing well graded material (25mm to 4.75 mm IRC HBG @ 65%,4.75 to 2.36mm IRC HBG metal @20%&2.36 mm below IRC HBG metal @15%)& (the material passing 425 microns sieve shall have liquid limit and plasticlty index not more than 25 & 6% respectively) spreading in uniform layers with motor grader on prepared surface

WET MIX MECADAM Providing and laying spreading and compacting graded stone aggregate to wet Mix Macadam(WMM) specification including premixing the material with water at OMC in machanical mix plant carriage of mixed material by tipper to site laying in uniform layers 250mm thick with pavers in SubBase/Base course on well prepared surface and compacting with vibratory roller to achieve the desired density including cost of material labour charges

PRIMER COAT Applying PRIMECOAT over WMB/WMB surface at 7.00kg of SS-1 Bitumen Emulsion / 10 sq.m including labour for spraying hire charges for bitumen sprayer etc., complete

TACK COAT Applying TACK COAT over Primed WMM surface at 2.5kg of Rs-1 Bitumen Emulsion / 10sq.m including labour for spraying hire charfes for bitumen sprayer etc., complete

Bituminous Concrete Providing and laying bituminious concrete to 40mm thick using 0.13 cum of 19.00-9.50mm. 0.17 cum of 9.5-2.36 and below with 50.3kgs of BG30/BG40 heating the bitumen and aggregates to required temperature and mixing then in required temperature in central hot mix plant 20-30 ton capacity,carrying the mix by tipper trucks to paver site ,spreading the mix to uniform thickness of 40mm with mechanical paver to the specified grades and cross sections and consolidated by 8-10 tons vibratery / phenumatic

C.C ROAD (PQC) Construction of un-reinforced, dowel joined at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade0 coarse and fine aggregated conforming to IS:383, maximum size of coarse aggregates not exceeding 25mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing) spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days using curing compound (whrer specified)

Provision for Name Board

Providing and Fixing of Cautionary, mandatory And Informatory sign Board Providing and fixing of Retro Reflectorisedn Cautionary, Mandatory Signs with Definition Plate made out of High Intensity Grade Prismatic Sheeting conforming to IRC-67:2010 & ASTM D 4956-09, Type IV Specification and Fixed over 1.5 mm thick Aluminium Sheet Fixed on back support Frame of 25mm X 25mm X 3mm Mild steel angle and supported on a mild steel angle iron post 75mm x 75mm X 6mmfirmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 45cm X 45cm X 60cm below Ground Level etc Complete including 7 years warranty for the Retro Reflective Sheeting as per clause 6.9 of IRC 67-2010 Specification (as per MORT & Spec No.801)

60 Cm Equilateral triangle (Cautionary ) sign Board

60 CmCircular (Manda+tory ) sign Board

Chevron signs 90 Cm

Reflector

Road Marking with hot applied thermoplastic compound with Reflectorising Glass Beads on Bituminous Surface KM 0/000-6/450S

Kilometre Stone Reinforced cement concrete M15 grade kilometre stone/local stone of standared design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Claused 1703

Ordinary Kilometer Stone (Precast)

200m Stone (Precast)

Guard stone (Precast)

Construction of 10m Span 15 Deg Skew Bridge at Ch. 1013

Dismantling, clearing away and carefully stacking materials useful for re use for any thickness of walls. Brick / Stone masonry in Lime mortar walls ad for every additional 3m or part there of over the initial height of 3m.

Earthwork excavation in all classes of soil except hard rock requiring blasting and depositing on bank with al leads and lifts as per SS20B, including cost of all labour, equipments and all incidental charges such as Bailing our water, providing And maintaining necessary cofferdams, sheeting, shoring bracing and their subsequent removal, removal of all logs, stumps, grubs and other deleterious matter and obstructions, trimming bottom of excavation backfilling , and clearing the site and disposal of all surplus materials etc., complete as per relevant standard specification for DRESSING THE BED UP TO SILL LEVEL.

Earthwork excavation in all classes of soil except hard rock requiring blasting and depositing on bank with al leads and lifts as per SS20B, including cost of all labour, equipments and all incidental charges such as Bailing our water, providing and maintaining necessary cofferdams, sheeting, shoring, bracing and their subsequent removal,removal of all logs, stumps, grubs and other deleterious matter and obstructions, trimming bottom of excavation backfilling, and clearing the site and disposal of all surplus materials etc., completee as per relevant standard specifications for FOUNDATION (OPEN FOUNDATION, RAFT FOUNDATION, CUT OFF WALL, FLEXIBLE & RIGID APRON) UNDER ABUTMENTS & PIERS BELOW SILL LEVEL

Vibrated Plain Cement Concrete of Grade M 20 Design Mix using 20mm & 12mm ISS size HBG metal including cost and conveyance of all materials to site including cost of cement at site including cost of formwork, soft water, labour charges for mixing, transporting, laying and curing concrete, working at depths, tools and plants and maintaining of protective bunds, cofferdams, shoring,strutting etc., complete as per relevant standard specifications for footing under ABUTMENT and Returns and piers

Vibrated Plain Cement Concrete of Grade M 20 Design Mix using 20mm & 12mm ISS size HBG metal including cost and conveyance of all materials to site including cost of cement at site including cost of formwork, soft water, labour charges for mixing, transporting, laying and curing concrete, working at depths, tools and plants and maintaining of protective bunds, cofferdams, shoring,strutting etc., complete as per relevant standard specifications for Sub structure of ABUTMENT, Piers & wingwall above sill level.

Providing and fixing seepage pipes of 100 mm dia. PVC pipes of required lengths for abutments and wings including cost and conveyance of all materials to work site, cost and labour for 900 mm Dia. Semi spherical back fill arrangements with 100mm, size broken granite chips at the periphery and labour charges for fixing etc., to drain of the backfill IN BETWEEN THE ABUTMENTS AND RETURNS.

Vibrated reinforced Cement Concrete of Grade M 30 Design Mix using 20mm & 12mm ISS size HBG metal including cost and conveyance of all materials to site including cost of cement at site including cost of formwork, soft water, labour charges for mixing, transporting, laying and curing concrete, working at depths, tools and plants and maintaining of protective bunds, cofferdams, shoring,strutting etc., complete as per relevant standard specifications for BED BLOCK OVER RCC abutment wall above sill level.

Providing and fixing Kraft Paper for full width of seating of deck and including cost and conveyance to work site Labour for fixing the same in correct position and all other incidental charges etc.,complete.

Vibrated reinforced Cement Concrete of Grade M 30 Design Mix using 20mm & 12mm ISS size HBG metal including cost and conveyance of all materials to site including cost of cement at site including cost of formwork, soft water, labour charges for mixing, transporting, laying and curing concrete, working at depths, tools and plants and maintaining of protective bunds, cofferdams, shoring,strutting etc., complete as per relevant standard specifications for RCC Deckslab & Kerb.

Vibrated cement concrete M30 design mix using ISS size HBG graded metal including cost and conveyance of all materials to worksite and cement at site including all labour charges for fixing concrete,laying,vibrating, hire charges for tools and plants, compacting, curing with all leads for soft water, including all other incident charges, formwork, cost of premoulded expansion joints and fixing the same in position etc., complete for wearing coat of 7mm uniform thickness over deck slab and approach slab.

Vibrated reinforced Cement Concrete of Grade M 30 Design Mix using 20mm & 12mm ISS size HBG metal including cost and conveyance of all materials to site including cost of cement at site including cost of formwork, soft water, labour charges for mixing, transporting, laying and curing concrete, working at depths, tools and plants and maintaining of protective bunds, cofferdams, shoring,strutting etc., complete as per relevant standard specifications for RCC Handrail.

Supply and fabrication of High Yield Strength Deformed Bar with Grade Designation Fe.415, conforming to IS:1786 1985, steel required for all RCC items of works involved in the schedule cost of steel at site fabrication labour charges for cleaning, bending tying grills, including overlapping to the required length whenever necessary and placing the reinforcement in position as specified in the drawings, including cost of binding wire, provision of spacer bars, cover blocks and all other incidental charges etc., complete, Fe.415 grade. TOR STEEL

Providing & fixing PVC Expansion joint in between Deck Slab over Abutment & Piers as shown in the drawing including cost & conveyance of Expansion Joint including Shalimar Pad and Joint sealant etc., complete.

Vibrated Cement Concrete of grade M 15 Nominal Mix 1:2:4 using 20mm ISS size HBG metal including cost and conveyance of all materials to site including cost of cement at site including cost of formwork, soft water, labour charges for mixing, transporting, laying and curing concrete, working at depths, tools and plants and maintaining of protective bunds, cofferdams, shoring, strutting etc., complete as per relevant standard specifications for BASE COURSE BELOW APPROACH SLAB

Vibrated reinforced cement concrete M 30 Grade, Design Mix using 20mm & 12mm ISS size hard granite broken graded metal including cost and conveyance of all materials to site and cement at site but excluding cost and fabrication of steel but including form work and centering soft water labour charges for mixing, transporting, placing in position, vibrating and compacting finishing and curing concrete working at heights, hire chargs for tools and plants, including all other incidental charges etc., complete as per standard specifications for Approach Slab

Filling behind Abutments and wings with clean gritty gravel including cost and conveyance of gravel to worksite, laying, handling charges and filling in layers, tamping under optimum moisture content to get the maximum density including watering with all leads for water and all other incidental charges etc., complete for filling behind the abutment and wings

Providing filter media behind the abutments and wings with clean III graded material 53mm to 5.6mm to 600mm thick and well compacted in layers with smaller sized towards the soil and bigger size towards the wall including cost and conveyance to work site including all labours and other incidental charges including hire charges for tools and plants employed etc., for filter media as per MOST's (Roads Wing) specifications for Roads and Bridges " Fourth Revision Cl. 309-3-2-13 and 305 -4-4 etc., complete.

Manufacturing and fixing cement blocks of size 250 x 250 x300mm in CC 1:2:4 nominal mix 15 using 20mm ISS Sixe HBG metal including cost and conveyance of all materials to worksite and cement site including conveyance and handling charges for the same at both ends including all other incidental charges etc., complete for REVETMENTS

Construction of 1.50m Span Culvert at Ch. 2085

Earth work excavation for foundation soil as per SS 20 B for foundation.

Filling with M.sand including including all labour charges for filling etc complete.

Cement Concrete 1:4:8 mix using 40mm HBG metal including all labour charges for filling etc complete.

Cement Concrete 1:3:6 mix using 40mm HBG metal including cost and conveyance of all materials to site including all labour charges for filling etc complete.

Centering for the sides and soffits RCC items including all cost and conveyance and all labour charges etc., complete.

Below sill

Above sill

Supplying and fabrication of steel rods including all cost and conveyance and all labour charges and all other incidental charges.

C.C. 1:2:4 mix using 20mm ISS HBG metal including cost and conveyance and all labour charges etc.complete.

R.C.C. 1:1.5:3 mix using 20mm ISS HBG metal including cost and conveyance and all labour charges etc.complete.

Providing and fixing 20mm Bitumen felt for expansion joint Between Dirtwall &Deck slab

Providing and fixing Tar Paper for bearing Between Bed Block & Deck slab

Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing

Gravel filling between body wall including cost and conveyance of gravel, labour for filling, watering and compacting etc complete complying with standard specification and as directed by the departmental officer.

Construction RCC 6.0m Span 35deg Skew Culvert @ Ch 2225

Earth work excavation for foundation soil as per SS 20 B for foundation.

Filling with M.sand including including all labour charges for filling etc complete.

Cement Concrete 1:4:8 mix using 40mm HBG metal including all labour charges for filling etc complete.

Cement Concrete 1:3:6 mix using 40mm HBG metal including cost and conveyance of all materials to site including all labour charges for filling etc complete.

Centering for the sides and soffits RCC items including all cost and conveyance and all labour charges etc., complete.

Below sill

Above sill

Supplying and fabrication of steel rods including all cost and conveyance and all labour charges and all other incidental charges.

C.C. 1:2:4 mix using 20mm ISS HBG metal including cost and conveyance and all labour charges etc.complete.

R.C.C. 1:1.5:3 mix using 20mm ISS HBG metal including cost and conveyance and all labour charges etc.complete.

Providing and fixing 20mm Bitumen felt for expansion joint Between Dirtwall &Deck slab

Providing and fixing Tar Paper for bearing Between Bed Block & Deck slab

Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing

Gravel filling between body wall including cost and conveyance of gravel, labour for filling, watering and compacting etc complete complying with standard specification and as directed by the departmental officer.

Construction RCC 3.0m Span Culvert @ Ch 2650

Earth work excavation for foundation soil as per SS 20 B for foundation.

Filling with M.sand including including all labour charges for filling etc complete.

Cement Concrete 1:4:8 mix using 40mm HBG metal including all labour charges for filling etc complete.

Cement Concrete 1:3:6 mix using 40mm HBG metal including cost and conveyance of all materials to site including all labour charges for filling etc complete.

Centering for the sides and soffits RCC items including all cost and conveyance and all labour charges etc., complete.

Below sill

Above sill

Supplying and fabrication of steel rods including all cost and conveyance and all labour charges and all other incidental charges.

C.C. 1:2:4 mix using 20mm ISS HBG metal including cost and conveyance and all labour charges etc.complete.

R.C.C. 1:1.5:3 mix using 20mm ISS HBG metal including cost and conveyance and all labour charges etc.complete.

Providing and fixing 20mm Bitumen felt for expansion joint Between Dirtwall &Deck slab

Providing and fixing Tar Paper for bearing Between Bed Block & Deck slab

Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing

Gravel filling between body wall including cost and conveyance of gravel, labour for filling, watering and compacting etc complete complying with standard specification and as directed by the departmental officer.

Construction of 10m Span 15 Deg Skew Bridge at Ch. 3060

Earthwork excavation in all classes of soil except hard rock requiring blasting and depositing on bank with al leads and lifts as per SS20B, including cost of all labour, equipments and all incidental charges such as Bailing our water, providing And maintaining necessary cofferdams, sheeting, shoring bracing and their subsequent removal, removal of all logs, stumps, grubs and other deleterious matter and obstructions, trimming bottom of excavation backfilling , and clearing the site and disposal of all surplus materials etc., complete as per relevant standard specification for DRESSING THE BED UP TO SILL LEVEL.

Earthwork excavation in all classes of soil except hard rock requiring blasting and depositing on bank with al leads and lifts as per SS20B, including cost of all labour, equipments and all incidental charges such as Bailing our water, providing and maintaining necessary cofferdams, sheeting, shoring, bracing and their subsequent removal,removal of all logs, stumps, grubs and other deleterious matter and obstructions, trimming bottom of excavation backfilling, and clearing the site and disposal of all surplus materials etc., completee as per relevant standard specifications for FOUNDATION (OPEN FOUNDATION, RAFT FOUNDATION, CUT OFF WALL, FLEXIBLE & RIGID APRON) UNDER ABUTMENTS & PIERS BELOW SILL LEVEL

Vibrated Plain Cement Concrete of Grade M 20 Design Mix using 20mm & 12mm ISS size HBG metal including cost and conveyance of all materials to site including cost of cement at site including cost of formwork, soft water, labour charges for mixing, transporting, laying and curing concrete, working at depths, tools and plants and maintaining of protective bunds, cofferdams, shoring,strutting etc., complete as per relevant standard specifications for footing under ABUTMENT and Returns and piers

Vibrated Plain Cement Concrete of Grade M 20 Design Mix using 20mm & 12mm ISS size HBG metal including cost and conveyance of all materials to site including cost of cement at site including cost of formwork, soft water, labour charges for mixing, transporting, laying and curing concrete, working at depths, tools and plants and maintaining of protective bunds, cofferdams, shoring,strutting etc., complete as per relevant standard specifications for Sub structure of ABUTMENT, Piers & wingwall above sill level.

Providing and fixing seepage pipes of 100 mm dia. PVC pipes of required lengths for abutments and wings including cost and conveyance of all materials to work site, cost and labour for 900 mm Dia. Semi spherical back fill arrangements with 100mm, size broken granite chips at the periphery and labour charges for fixing etc., to drain of the backfill IN BETWEEN THE ABUTMENTS AND RETURNS.

Vibrated reinforced Cement Concrete of Grade M 30 Design Mix using 20mm & 12mm ISS size HBG metal including cost and conveyance of all materials to site including cost of cement at site including cost of formwork, soft water, labour charges for mixing, transporting, laying and curing concrete, working at depths, tools and plants and maintaining of protective bunds, cofferdams, shoring,strutting etc., complete as per relevant standard specifications for BED BLOCK OVER RCC abutment wall above sill level.

Providing and fixing Kraft Paper for full width of seating of deck and including cost and conveyance to work site Labour for fixing the same in correct position and all other incidental charges etc.,complete.

Vibrated reinforced Cement Concrete of Grade M 30 Design Mix using 20mm & 12mm ISS size HBG metal including cost and conveyance of all materials to site including cost of cement at site including cost of formwork, soft water, labour charges for mixing, transporting, laying and curing concrete, working at depths, tools and plants and maintaining of protective bunds, cofferdams, shoring,strutting etc., complete as per relevant standard specifications for RCC Deckslab & Kerb.

Vibrated cement concrete M30 design mix using ISS size HBG graded metal including cost and conveyance of all materials to worksite and cement at site including all labour charges for fixing concrete,laying,vibrating, hire charges for tools and plants, compacting, curing with all leads for soft water, including all other incident charges, formwork, cost of premoulded expansion joints and fixing the same in position etc., complete for wearing coat of 7mm uniform thickness over deck slab and approach slab.

Vibrated reinforced Cement Concrete of Grade M 30 Design Mix using 20mm & 12mm ISS size HBG metal including cost and conveyance of all materials to site including cost of cement at site including cost of formwork, soft water, labour charges for mixing, transporting, laying and curing concrete, working at depths, tools and plants and maintaining of protective bunds, cofferdams, shoring,strutting etc., complete as per relevant standard specifications for RCC Handrail.

Supply and fabrication of High Yield Strength Deformed Bar with Grade Designation Fe.415, conforming to IS:1786 1985, steel required for all RCC items of works involved in the schedule cost of steel at site fabrication labour charges for cleaning, bending tying grills, including overlapping to the required length whenever necessary and placing the reinforcement in position as specified in the drawings, including cost of binding wire, provision of spacer bars, cover blocks and all other incidental charges etc., complete, Fe.415 grade. TOR STEEL

Providing & fixing PVC Expansion joint in between Deck Slab over Abutment & Piers as shown in the drawing including cost & conveyance of Expansion Joint including Shalimar Pad and Joint sealant etc., complete.

Vibrated Cement Concrete of grade M 15 Nominal Mix 1:2:4 using 20mm ISS size HBG metal including cost and conveyance of all materials to site including cost of cement at site including cost of formwork, soft water, labour charges for mixing, transporting, laying and curing concrete, working at depths, tools and plants and maintaining of protective bunds, cofferdams, shoring, strutting etc., complete as per relevant standard specifications for BASE COURSE BELOW APPROACH SLAB

Vibrated reinforced cement concrete M 30 Grade, Design Mix using 20mm & 12mm ISS size hard granite broken graded metal including cost and conveyance of all materials to site and cement at site but excluding cost and fabrication of steel but including form work and centering soft water labour charges for mixing, transporting, placing in position, vibrating and compacting finishing and curing concrete working at heights, hire chargs for tools and plants, including all other incidental charges etc., complete as per standard specifications for Approach Slab

Filling behind Abutments and wings with clean gritty gravel including cost and conveyance of gravel to worksite, laying, handling charges and filling in layers, tamping under optimum moisture content to get the maximum density including watering with all leads for water and all other incidental charges etc., complete for filling behind the abutment and wings

Providing filter media behind the abutments and wings with clean III graded material 53mm to 5.6mm to 600mm thick and well compacted in layers with smaller sized towards the soil and bigger size towards the wall including cost and conveyance to work site including all labours and other incidental charges including hire charges for tools and plants employed etc., for filter media as per MOST's (Roads Wing) specifications for Roads and Bridges " Fourth Revision Cl. 309-3-2-13 and 305 -4-4 etc., complete.

Manufacturing and fixing cement blocks of size 250 x 250 x300mm in CC 1:2:4 nominal mix 15 using 20mm ISS Sixe HBG metal including cost and conveyance of all materials to worksite and cement site including conveyance and handling charges for the same at both ends including all other incidental charges etc., complete for REVETMENTS

Construction RCC 6.0m Span 35deg Skew Culvert @ Ch 3290

Earth work excavation for foundation soil as per SS 20 B for foundation.

Filling with M.sand including including all labour charges for filling etc complete.

Cement Concrete 1:4:8 mix using 40mm HBG metal including all labour charges for filling etc complete.

Cement Concrete 1:3:6 mix using 40mm HBG metal including cost and conveyance of all materials to site including all labour charges for filling etc complete.

Centering for the sides and soffits RCC items including all cost and conveyance and all labour charges etc., complete.

Below sill

Above sill

Supplying and fabrication of steel rods including all cost and conveyance and all labour charges and all other incidental charges.

C.C. 1:2:4 mix using 20mm ISS HBG metal including cost and conveyance and all labour charges etc.complete.

R.C.C. 1:1.5:3 mix using 20mm ISS HBG metal including cost and conveyance and all labour charges etc.complete.

Providing and fixing 20mm Bitumen felt for expansion joint Between Dirtwall &Deck slab

Providing and fixing Tar Paper for bearing Between Bed Block & Deck slab

Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing

Gravel filling between body wall including cost and conveyance of gravel, labour for filling, watering and compacting etc complete complying with standard specification and as directed by the departmental officer.

Construction RCC 6.0m Span 35deg Skew Culvert @ Ch 3445

Earth work excavation for foundation soil as per SS 20 B for foundation.

Filling with M.sand including including all labour charges for filling etc complete.

Cement Concrete 1:4:8 mix using 40mm HBG metal including all labour charges for filling etc complete.

Cement Concrete 1:3:6 mix using 40mm HBG metal including cost and conveyance of all materials to site including all labour charges for filling etc complete.

Centering for the sides and soffits RCC items including all cost and conveyance and all labour charges etc., complete.

Below sill

Above sill

Supplying and fabrication of steel rods including all cost and conveyance and all labour charges and all other incidental charges.

C.C. 1:2:4 mix using 20mm ISS HBG metal including cost and conveyance and all labour charges etc.complete.

R.C.C. 1:1.5:3 mix using 20mm ISS HBG metal including cost and conveyance and all labour charges etc.complete.

Providing and fixing 20mm Bitumen felt for expansion joint Between Dirtwall &Deck slab

Providing and fixing Tar Paper for bearing Between Bed Block & Deck slab

Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing

Gravel filling between body wall including cost and conveyance of gravel, labour for filling, watering and compacting etc complete complying with standard specification and as directed by the departmental officer.

Construction RCC 6.0m Span 35deg Skew Culvert @ Ch 3620

Earth work excavation for foundation soil as per SS 20 B for foundation.

Filling with M.sand including including all labour charges for filling etc complete.

Cement Concrete 1:4:8 mix using 40mm HBG metal including all labour charges for filling etc complete.

Cement Concrete 1:3:6 mix using 40mm HBG metal including cost and conveyance of all materials to site including all labour charges for filling etc complete.

Centering for the sides and soffits RCC items including all cost and conveyance and all labour charges etc., complete.

Below sill

Above sill

Supplying and fabrication of steel rods including all cost and conveyance and all labour charges and all other incidental charges.

C.C. 1:2:4 mix using 20mm ISS HBG metal including cost and conveyance and all labour charges etc.complete.

R.C.C. 1:1.5:3 mix using 20mm ISS HBG metal including cost and conveyance and all labour charges etc.complete.

Providing and fixing 20mm Bitumen felt for expansion joint Between Dirtwall &Deck slab

Providing and fixing Tar Paper for bearing Between Bed Block & Deck slab

Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing

Gravel filling between body wall including cost and conveyance of gravel, labour for filling, watering and compacting etc complete complying with standard specification and as directed by the departmental officer.

Construction of 10m Span 15 Deg Skew Bridge at Ch. 4090

Earthwork excavation in all classes of soil except hard rock requiring blasting and depositing on bank with al leads and lifts as per SS20B, including cost of all labour, equipments and all incidental charges such as Bailing our water, providing And maintaining necessary cofferdams, sheeting, shoring bracing and their subsequent removal, removal of all logs, stumps, grubs and other deleterious matter and obstructions, trimming bottom of excavation backfilling , and clearing the site and disposal of all surplus materials etc., complete as per relevant standard specification for DRESSING THE BED UP TO SILL LEVEL.

Earthwork excavation in all classes of soil except hard rock requiring blasting and depositing on bank with al leads and lifts as per SS20B, including cost of all labour, equipments and all incidental charges such as Bailing our water, providing and maintaining necessary cofferdams, sheeting, shoring, bracing and their subsequent removal,removal of all logs, stumps, grubs and other deleterious matter and obstructions, trimming bottom of excavation backfilling, and clearing the site and disposal of all surplus materials etc., completee as per relevant standard specifications for FOUNDATION (OPEN FOUNDATION, RAFT FOUNDATION, CUT OFF WALL, FLEXIBLE & RIGID APRON) UNDER ABUTMENTS & PIERS BELOW SILL LEVEL

Vibrated Plain Cement Concrete of Grade M 20 Design Mix using 20mm & 12mm ISS size HBG metal including cost and conveyance of all materials to site including cost of cement at site including cost of formwork, soft water, labour charges for mixing, transporting, laying and curing concrete, working at depths, tools and plants and maintaining of protective bunds, cofferdams, shoring,strutting etc., complete as per relevant standard specifications for footing under ABUTMENT and Returns and piers

Vibrated Plain Cement Concrete of Grade M 20 Design Mix using 20mm & 12mm ISS size HBG metal including cost and conveyance of all materials to site including cost of cement at site including cost of formwork, soft water, labour charges for mixing, transporting, laying and curing concrete, working at depths, tools and plants and maintaining of protective bunds, cofferdams, shoring,strutting etc., complete as per relevant standard specifications for Sub structure of ABUTMENT, Piers & wingwall above sill level.

Providing and fixing seepage pipes of 100 mm dia. PVC pipes of required lengths for abutments and wings including cost and conveyance of all materials to work site, cost and labour for 900 mm Dia. Semi spherical back fill arrangements with 100mm, size broken granite chips at the periphery and labour charges for fixing etc., to drain of the backfill IN BETWEEN THE ABUTMENTS AND RETURNS.

Vibrated reinforced Cement Concrete of Grade M 30 Design Mix using 20mm & 12mm ISS size HBG metal including cost and conveyance of all materials to site including cost of cement at site including cost of formwork, soft water, labour charges for mixing, transporting, laying and curing concrete, working at depths, tools and plants and maintaining of protective bunds, cofferdams, shoring,strutting etc., complete as per relevant standard specifications for BED BLOCK OVER RCC abutment wall above sill level.

Providing and fixing Kraft Paper for full width of seating of deck and including cost and conveyance to work site Labour for fixing the same in correct position and all other incidental charges etc.,complete.

Vibrated reinforced Cement Concrete of Grade M 30 Design Mix using 20mm & 12mm ISS size HBG metal including cost and conveyance of all materials to site including cost of cement at site including cost of formwork, soft water, labour charges for mixing, transporting, laying and curing concrete, working at depths, tools and plants and maintaining of protective bunds, cofferdams, shoring,strutting etc., complete as per relevant standard specifications for RCC Deckslab & Kerb.

Vibrated cement concrete M30 design mix using ISS size HBG graded metal including cost and conveyance of all materials to worksite and cement at site including all labour charges for fixing concrete,laying,vibrating, hire charges for tools and plants, compacting, curing with all leads for soft water, including all other incident charges, formwork, cost of premoulded expansion joints and fixing the same in position etc., complete for wearing coat of 7mm uniform thickness over deck slab and approach slab.

Vibrated reinforced Cement Concrete of Grade M 30 Design Mix using 20mm & 12mm ISS size HBG metal including cost and conveyance of all materials to site including cost of cement at site including cost of formwork, soft water, labour charges for mixing, transporting, laying and curing concrete, working at depths, tools and plants and maintaining of protective bunds, cofferdams, shoring,strutting etc., complete as per relevant standard specifications for RCC Handrail.

Supply and fabrication of High Yield Strength Deformed Bar with Grade Designation Fe.415, conforming to IS:1786 1985, steel required for all RCC items of works involved in the schedule cost of steel at site fabrication labour charges for cleaning, bending tying grills, including overlapping to the required length whenever necessary and placing the reinforcement in position as specified in the drawings, including cost of binding wire, provision of spacer bars, cover blocks and all other incidental charges etc., complete, Fe.415 grade. TOR STEEL

Providing & fixing PVC Expansion joint in between Deck Slab over Abutment & Piers as shown in the drawing including cost & conveyance of Expansion Joint including Shalimar Pad and Joint sealant etc., complete.

Vibrated Cement Concrete of grade M 15 Nominal Mix 1:2:4 using 20mm ISS size HBG metal including cost and conveyance of all materials to site including cost of cement at site including cost of formwork, soft water, labour charges for mixing, transporting, laying and curing concrete, working at depths, tools and plants and maintaining of protective bunds, cofferdams, shoring, strutting etc., complete as per relevant standard specifications for BASE COURSE BELOW APPROACH SLAB

Vibrated reinforced cement concrete M 30 Grade, Design Mix using 20mm & 12mm ISS size hard granite broken graded metal including cost and conveyance of all materials to site and cement at site but excluding cost and fabrication of steel but including form work and centering soft water labour charges for mixing, transporting, placing in position, vibrating and compacting finishing and curing concrete working at heights, hire chargs for tools and plants, including all other incidental charges etc., complete as per standard specifications for Approach Slab

Filling behind Abutments and wings with clean gritty gravel including cost and conveyance of gravel to worksite, laying, handling charges and filling in layers, tamping under optimum moisture content to get the maximum density including watering with all leads for water and all other incidental charges etc., complete for filling behind the abutment and wings

Providing filter media behind the abutments and wings with clean III graded material 53mm to 5.6mm to 600mm thick and well compacted in layers with smaller sized towards the soil and bigger size towards the wall including cost and conveyance to work site including all labours and other incidental charges including hire charges for tools and plants employed etc., for filter media as per MOST's (Roads Wing) specifications for Roads and Bridges " Fourth Revision Cl. 309-3-2-13 and 305 -4-4 etc., complete.

Manufacturing and fixing cement blocks of size 250 x 250 x300mm in CC 1:2:4 nominal mix 15 using 20mm ISS Sixe HBG metal including cost and conveyance of all materials to worksite and cement site including conveyance and handling charges for the same at both ends including all other incidental charges etc., complete for REVETMENTS

Construction of 8m Span 15 Deg Skew Bridge at Ch. 4256

Earthwork excavation in all classes of soil except hard rock requiring blasting and depositing on bank with al leads and lifts as per SS20B, including cost of all labour, equipments and all incidental charges such as Bailing our water, providing And maintaining necessary cofferdams, sheeting, shoring bracing and their subsequent removal, removal of all logs, stumps, grubs and other deleterious matter and obstructions, trimming bottom of excavation backfilling , and clearing the site and disposal of all surplus materials etc., complete as per relevant standard specification for DRESSING THE BED UP TO SILL LEVEL.

Earthwork excavation in all classes of soil except hard rock requiring blasting and depositing on bank with al leads and lifts as per SS20B, including cost of all labour, equipments and all incidental charges such as Bailing our water, providing and maintaining necessary cofferdams, sheeting, shoring, bracing and their subsequent removal,removal of all logs, stumps, grubs and other deleterious matter and obstructions, trimming bottom of excavation backfilling, and clearing the site and disposal of all surplus materials etc., completee as per relevant standard specifications for FOUNDATION (OPEN FOUNDATION, RAFT FOUNDATION, CUT OFF WALL, FLEXIBLE & RIGID APRON) UNDER ABUTMENTS & PIERS BELOW SILL LEVEL

Vibrated Plain Cement Concrete of Grade M 20 Design Mix using 20mm & 12mm ISS size HBG metal including cost and conveyance of all materials to site including cost of cement at site including cost of formwork, soft water, labour charges for mixing, transporting, laying and curing concrete, working at depths, tools and plants and maintaining of protective bunds, cofferdams, shoring,strutting etc., complete as per relevant standard specifications for footing under ABUTMENT and Returns and piers

Vibrated Plain Cement Concrete of Grade M 20 Design Mix using 20mm & 12mm ISS size HBG metal including cost and conveyance of all materials to site including cost of cement at site including cost of formwork, soft water, labour charges for mixing, transporting, laying and curing concrete, working at depths, tools and plants and maintaining of protective bunds, cofferdams, shoring,strutting etc., complete as per relevant standard specifications for Sub structure of ABUTMENT, Piers & wingwall above sill level.

Providing and fixing seepage pipes of 100 mm dia. PVC pipes of required lengths for abutments and wings including cost and conveyance of all materials to work site, cost and labour for 900 mm Dia. Semi spherical back fill arrangements with 100mm, size broken granite chips at the periphery and labour charges for fixing etc., to drain of the backfill IN BETWEEN THE ABUTMENTS AND RETURNS.

Vibrated reinforced Cement Concrete of Grade M 30 Design Mix using 20mm & 12mm ISS size HBG metal including cost and conveyance of all materials to site including cost of cement at site including cost of formwork, soft water, labour charges for mixing, transporting, laying and curing concrete, working at depths, tools and plants and maintaining of protective bunds, cofferdams, shoring,strutting etc., complete as per relevant standard specifications for BED BLOCK OVER RCC abutment wall above sill level.

Providing and fixing Kraft Paper for full width of seating of deck and including cost and conveyance to work site Labour for fixing the same in correct position and all other incidental charges etc.,complete.

Vibrated reinforced Cement Concrete of Grade M 30 Design Mix using 20mm & 12mm ISS size HBG metal including cost and conveyance of all materials to site including cost of cement at site including cost of formwork, soft water, labour charges for mixing, transporting, laying and curing concrete, working at depths, tools and plants and maintaining of protective bunds, cofferdams, shoring,strutting etc., complete as per relevant standard specifications for RCC Deckslab & Kerb.

Vibrated cement concrete M30 design mix using ISS size HBG graded metal including cost and conveyance of all materials to worksite and cement at site including all labour charges for fixing concrete,laying,vibrating, hire charges for tools and plants, compacting, curing with all leads for soft water, including all other incident charges, formwork, cost of premoulded expansion joints and fixing the same in position etc., complete for wearing coat of 7mm uniform thickness over deck slab and approach slab.

Vibrated reinforced Cement Concrete of Grade M 30 Design Mix using 20mm & 12mm ISS size HBG metal including cost and conveyance of all materials to site including cost of cement at site including cost of formwork, soft water, labour charges for mixing, transporting, laying and curing concrete, working at depths, tools and plants and maintaining of protective bunds, cofferdams, shoring,strutting etc., complete as per relevant standard specifications for RCC Handrail.

Supply and fabrication of High Yield Strength Deformed Bar with Grade Designation Fe.415, conforming to IS:1786 1985, steel required for all RCC items of works involved in the schedule cost of steel at site fabrication labour charges for cleaning, bending tying grills, including overlapping to the required length whenever necessary and placing the reinforcement in position as specified in the drawings, including cost of binding wire, provision of spacer bars, cover blocks and all other incidental charges etc., complete, Fe.415 grade. TOR STEEL

Providing & fixing PVC Expansion joint in between Deck Slab over Abutment & Piers as shown in the drawing including cost & conveyance of Expansion Joint including Shalimar Pad and Joint sealant etc., complete.

Vibrated Cement Concrete of grade M 15 Nominal Mix 1:2:4 using 20mm ISS size HBG metal including cost and conveyance of all materials to site including cost of cement at site including cost of formwork, soft water, labour charges for mixing, transporting, laying and curing concrete, working at depths, tools and plants and maintaining of protective bunds, cofferdams, shoring, strutting etc., complete as per relevant standard specifications for BASE COURSE BELOW APPROACH SLAB

Vibrated reinforced cement concrete M 30 Grade, Design Mix using 20mm & 12mm ISS size hard granite broken graded metal including cost and conveyance of all materials to site and cement at site but excluding cost and fabrication of steel but including form work and centering soft water labour charges for mixing, transporting, placing in position, vibrating and compacting finishing and curing concrete working at heights, hire chargs for tools and plants, including all other incidental charges etc., complete as per standard specifications for Approach Slab

Filling behind Abutments and wings with clean gritty gravel including cost and conveyance of gravel to worksite, laying, handling charges and filling in layers, tamping under optimum moisture content to get the maximum density including watering with all leads for water and all other incidental charges etc., complete for filling behind the abutment and wings

Providing filter media behind the abutments and wings with clean III graded material 53mm to 5.6mm to 600mm thick and well compacted in layers with smaller sized towards the soil and bigger size towards the wall including cost and conveyance to work site including all labours and other incidental charges including hire charges for tools and plants employed etc., for filter media as per MOST's (Roads Wing) specifications for Roads and Bridges " Fourth Revision Cl. 309-3-2-13 and 305 -4-4 etc., complete.

Manufacturing and fixing cement blocks of size 250 x 250 x300mm in CC 1:2:4 nominal mix 15 using 20mm ISS Sixe HBG metal including cost and conveyance of all materials to worksite and cement site including conveyance and handling charges for the same at both ends including all other incidental charges etc., complete for REVETMENTS

Construction RCC 6.0m Span 35deg Skew Culvert @ Ch 4630

Earth work excavation for foundation soil as per SS 20 B for foundation.

Filling with M.sand including including all labour charges for filling etc complete.

Cement Concrete 1:4:8 mix using 40mm HBG metal including all labour charges for filling etc complete.

Cement Concrete 1:3:6 mix using 40mm HBG metal including cost and conveyance of all materials to site including all labour charges for filling etc complete.

Centering for the sides and soffits RCC items including all cost and conveyance and all labour charges etc., complete.

Below sill

Above sill

Supplying and fabrication of steel rods including all cost and conveyance and all labour charges and all other incidental charges.

C.C. 1:2:4 mix using 20mm ISS HBG metal including cost and conveyance and all labour charges etc.complete.

R.C.C. 1:1.5:3 mix using 20mm ISS HBG metal including cost and conveyance and all labour charges etc.complete.

Providing and fixing 20mm Bitumen felt for expansion joint Between Dirtwall &Deck slab

Providing and fixing Tar Paper for bearing Between Bed Block & Deck slab

Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing

Gravel filling between body wall including cost and conveyance of gravel, labour for filling, watering and compacting etc complete complying with standard specification and as directed by the departmental officer.

Construction RCC 5.0m Span 35deg Skew Culvert @ Ch 6000

Earth work excavation for foundation soil as per SS 20 B for foundation.

Filling with M.sand including including all labour charges for filling etc complete.

Cement Concrete 1:4:8 mix using 40mm HBG metal including all labour charges for filling etc complete.

Cement Concrete 1:3:6 mix using 40mm HBG metal including cost and conveyance of all materials to site including all labour charges for filling etc complete.

Centering for the sides and soffits RCC items including all cost and conveyance and all labour charges etc., complete.

Below sill

Above sill

Supplying and fabrication of steel rods including all cost and conveyance and all labour charges and all other incidental charges.

C.C. 1:2:4 mix using 20mm ISS HBG metal including cost and conveyance and all labour charges etc.complete.

R.C.C. 1:1.5:3 mix using 20mm ISS HBG metal including cost and conveyance and all labour charges etc.complete.

Providing and fixing 20mm Bitumen felt for expansion joint Between Dirtwall &Deck slab

Providing and fixing Tar Paper for bearing Between Bed Block & Deck slab

Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing

Gravel filling between body wall including cost and conveyance of gravel, labour for filling, watering and compacting etc complete complying with standard specification and as directed by the departmental officer.

Construction Retaining Wall @ Ch 6275-6325 (Rightside) & Ch 6325-6445 (Rightside)

Earth work excavation for foundation soil as per SS 20 B for foundation.

Ch 6275-6325 (Rightside)

Ch 6325-6445 (Rightside)

Filling with M.sand including including all labour charges for filling etc complete.

Ch 6275-6325 (Rightside)

Ch 6325-6445 (Rightside)

Cement Concrete 1:4:8 mix using 40mm HBG metal including all labour charges for filling etc complete.

Ch 6275-6325 (Rightside)

Ch 6325-6445 (Rightside)

Cement Concrete 1:3:6 mix using 40mm HBG metal including cost and conveyance of all materials to site including all labour charges for filling etc complete.

Ch 6275-6325 (Rightside)

Ch 6325-6445 (Rightside)

Cement Concrete 1:3:6 mix using 40mm HBG metal including cost and conveyance of all materials to site including all labour charges for filling etc complete.

Ch 6275-6325 (Rightside)

Ch 6325-6445 (Rightside)

Centering for the sides and soffits RCC items including all cost and conveyance and all labour charges etc., complete.

Ch 6275-6325 (Rightside)

Ch 6325-6445 (Rightside)

Towards the charges for routline maintenance of the road work executed under MGSMT including dressing of berms by refilling the gully with the earth from borrow pits, cleaning of wild seasonal growth on berms, destilting of side drains and CD works, white washing guard stones, painting of KM, HM stones, parapets, cutting of branches of trees, refixing displaced guard stones, caution boards, speed limit boards etc., with the periodicity for the above activities as prescribed in IRC-SP-20:2002 and as directed by the departmental officers except for the constructional defects which has to be rectified by the contractor at his own cost for carriageway width of 3.00m & 3.75m

For the First Year from the date of completion of work

For the Second Year from the date of cpmpletion of work

For the Third Year from the date of completion of work

For the Fourth Year from the date of completion of work

For the Fifth Year from the date of completion of work

GST Amount for providing Service to Government Contract Works for the above Construction Works. { GST Amount is the Total GST Amount for total overall quoted amount above this row in column "BB" for all works in this package}

CKS CONSTRUCTIONS