Provn of 07 Nos Rifle Rack and 07 Nos Bench Wksp and special repair replacement of Bed Hard Wooden and Charpoy GI pipe at Suratgarh Military Station

Amount

Supply & fixing Rifle Rack for 20 Rifles complete all as specified, shown on drawings and as directed. BTD-096

Supply of Work Bench Work Shop (Steel), 1500 x 900 x 760mm FD-1024

Material & Labour for removing carefully following existing unserviceable components/members of Bed Plywood Top and supply & fixing new components/members complete all as shown on drawing, as specified and as directed :- FD-246

Leg made out of Shisham wood. FD-246

Long rail made out of Shisham wood. FD-246

Short rail made out of long rail retrieved from serial item No. 3.02 here-in-before. Note : Short rail shall be prepared from old long rail and fixed in position. FD-246

Head Board complete as per drawing. FD-246

Foot Board complete as per drawing. FD-246

Ply wood 4 mm thick one side Teak face & other side commercial type on outer side of Head board. FD-246

Ply wood 4 mm thick one side Teak face & other side commercial type in inner side of Head board. FD-246

Ply wood 4 mm thick one side Teak face & other side commercial type on outer side of Foot board. FD-246

Ply wood 4 mm thick one side Teak face & other side commercial type in inner side of Foot board. FD-246

Beading of 1st class hard wood (Teak) of size 19 mm wide & 6mm thick for Head board / Foot board. FD-246

Top of bed of 12mm thick Plywood, 7 Ply, commercial type, BWR, exterior grade (water proof), ISI marked of size 1800mm x 900mm in single piece fixed with screws. Notes :- (i) The above mentioned size of plywood is firm and no tolerance in size, thickness etc shall be accepted. (ii) Plywood shall be provided in single piece in each Bed. (iii) Purchase voucher of plywood shall be obtained by the contractor from authorised dealer/manufacturer and shall be submitted to Engineer-in-Charge. FD-246

M&L for French polish two coats to achieve gloss finish on complete Bed Plywood Top after preparation of surfaces by removing old polish by scratching & rubbing with suitable sand paper, filling putty wherever required and making the surfaces smooth complete all as specified, shown on drawings and as directed. FD-246

Material & Labour for removing of unserviceable nylon newar from charpoy GI pipe, tightening of all loose components of complete charpoy such as check nuts, elbows, long rails, short rails, legs, etc and supply and fixing 12mm thick Plywood, 7 Ply, commercial type, BWR, exterior grade (water proof), ISI marked, of size 1980 mm x 920 mm in single piece fixed on top of Charpoy GI pipe with & including supplying and fixing two Nos stiffeners made out of mild steel flat iron 35mmx5mm, 880mm long between long rails parallel to short rails with equal spacing and power welding duly painted with two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer, plywood top fixed with and including mild steel galvanized iron nuts & bolts of size 70mm long x 6mm dia (Nos of bolts to be provided - 12 Nos) with GI washers of suitable size (Heavy weight) in sufficient numbers on top of bolts to maintain the plywood top in true leveled position and one GI washer on underside of each bolt for proper tightening of bolt, embossing word "MES” with height of letters 10cm on four corners of the plywood top with thick black synthetic enamel paint, complete all as specified, shown on drawings and as directed. Notes :- (i) The above mentioned size of plywood is firm and no tolerance in size, thickness etc shall be accepted. (ii) Plywood shall be provided in single piece in each Charpoy. (iii) Electric arc welding shall be used to fix stiffeners. (iv) Welding rod shall be ISI marked. (v) Purchase voucher of plywood shall be obtained by the contractor from authorised dealer/manufacturer and shall be submitted to Engineer-in-Charge. FD-220

Material & Labour for removing of unserviceable ply wood top from charpoy GI pipe with ply wood top and supply and fixing 12mm thick Plywood, 7 Ply, commercial type, BWR, exterior grade (water proof), ISI marked, of size 1980 mm x 900 mm in single piece fixed on top of Charpoy GI pipe, fixed with and including mild steel galvanized iron nuts & bolts of size 70mm long x 6mm dia (Nos of bolts to be provided - 11 Nos) with GI washers of suitable size (Heavy weight) in sufficient numbers on top of bolts to maintain the plywood top in true leveled position and one GI washer on underside of each bolt for proper tightening of bolt, embossing word "MES” with height of letters 10cm on four corners of the plywood top with thick black synthetic enamel paint, complete all as specified, shown on drawings and as directed. Notes :- (i) The above mentioned size of plywood is firm and no tolerance in size, thickness etc shall be accepted. (ii) Plywood shall be provided in single piece in each Charpoy. (iii) Purchase voucher of plywood shall be obtained by the contractor from authorised dealer/manufacturer and shall be submitted to Engineer-in-Charge. FD-220

Material & Labour for removing of unserviceable long rail of Charpoy GI pipe and supply and fixing new long rail made out of GI tubing 32 mm bore, medium grade, ISI Marked, 1980mm long, duly continuous welded properly at both ends as per best trade practice and also duly painted with aluminium paint on welded portion, complete all as specified, shown on drawings and as directed. Notes :- (i) Welding of new rail shall be as per best trade practice with continuous welding and as approved by GE. (ii) Unit for measurement of this item is ‘Each’ which shall comprise of removing of one old long rail and supply and fixing of one new long rail in lieu. (iii) Electric arc welding shall be used. (iv) Welding rod shall be ISI marked. FD-220

Dismantling carefully unserviceable short rail of Charpoy GI pipe and replacement by short rail made out from old long rail GI pipe retrieved under serial item No. 7 here-in-before, duly continuous welded properly at both ends as per best trade practice and also duly painted with aluminium paint on welded portion, complete all as specified, shown on drawings and as directed. Notes :- (i) Welding of rail shall be as per best trade practice with continuous welding and as approved by GE. (ii) Unit for measurement of this item is ‘Each’ which shall comprise of removing of one old short rail and fixing of one short rail in lieu made out of old long rail. (iii) The rate quoted for this item shall include for making of short rail by cutting from old long rail in appropriate size. (iv) Electric arc welding shall be used. (v) Welding rod shall be ISI marked. FD-220

Dismantling carefully unserviceable leg of Charpoy GI pipe and replacement by leg made out from old short rail GI pipe retrieved under serial item No. 8 here-in-before, duly continuous welded properly at one end as per best trade practice and also duly painted with aluminium paint on welded portion, complete all as specified, shown on drawings and as directed. Notes :- (i) Welding of leg shall be as per best trade practice with continuous welding and as approved by GE. (ii) Unit for measurement of this item is ‘Each’ which shall comprise of removing of one old leg and fixing of one leg in lieu made out of old short rail. (iii) The rate quoted for this item shall include for making of leg by cutting from old short rail in appropriate size. (iv) Electric arc welding shall be used. (v) Welding rod shall be ISI marked. FD-220

Material & Labour for removing of unserviceable long rail of Charpoy GI pipe and supply and fixing new long rail made out of GI tubing 32 mm bore, medium grade, ISI Marked, duly threaded at both ends complete all as specified, shown on drawings and as directed. Notes :- Unit for measurement of this item is ‘Each’ which shall comprise of removing of one old long rail and supply and fixing of one new long rail in lieu. FD-220

Dismantling carefully unserviceable short rail of Charpoy GI pipe and replacement by short rail made out from old long rail GI pipe retrieved under serial item No. 10 here-in-before, duly threaded at both ends complete all as specified, shown on drawings and as directed. Notes :- (i) Unit for measurement of this item is ‘Each’ which shall comprise of removing of one old short rail and fixing of one short rail in lieu made out of old long rail. (ii) The rate quoted for this item shall include for making of short rail by cutting from old long rail in appropriate size and providing threading at both ends of short rail. FD-220

Dismantling carefully unserviceable leg of Charpoy GI pipe and replacement by leg made out from old short rail GI pipe retrieved under serial item No. 11 here-in-before, duly threaded at one end complete all as specified, shown on drawings and as directed. Notes :- (i) Unit for measurement of this item is ‘Each’ which shall comprise of removing of one old leg and fixing of one leg in lieu made out of old short rail. (ii) The rate quoted for this item shall include for making of leg by cutting from old short rail in appropriate size and providing threading at one upper end of leg. FD-220

Supply & fixing in position GI 3 way elbow 32mm bore, medium grade (‘B’ Class), ISI marked in Charpoy GI pipe including dismantling & taking out carefully old unserviceable GI 3 way elbow 32mm bore complete all as specified, shown on drawings and as directed. FD-220

Supply & fixing in position GI check nut 6mm thick 32mm bore, medium grade (‘B’ Class), ISI marked in Charpoy GI pipe including dismantling & taking out carefully old unserviceable GI check nut complete all as specified, shown on drawings and as directed. FD-220

Supply & fixing mild steel 5mm thick & 35mm dia plate to the bottom of leg of Charpoy GI pipe duly continuous welded as per best trade practice and also duly painted with two coats of aluminium paint including taking out carefully old unserviceable wooden block from lower end of leg complete all as specified, shown on drawings and as directed. FD-220

Supply & fixing in replacement mild steel galvanized iron nut & bolt of size 70mm long x 6mm dia with GI washers (02 Nos) of suitable size (Heavy weight) to the Charpoy GI pipe complete all as specified, shown on drawings and as directed. Notes :- (i) Unit for measurement of this item is ‘Each’ which shall comprise of one bolt, one nut & two washers. (ii) This item shall not be paid for serial item No. 5 & 6 here-in-before. FD-220

Supply & fixing clamp made from flat iron 25x3mm, made to shape and welded to GI leg of Charpoy GI pipe for fixing conduit for MNF Set with & including 16 Gauge MS washer welded at bottom of clamp duly painted with two coats of black paint, fixed as lower clamp to leg, complete all as specified, shown on drawings and as directed. FD-220

Supply & fixing clamp made from flat iron 25x3mm, made to shape and welded to GI leg of Charpoy GI pipe for fixing conduit for MNF Set (without washer) duly painted with two coats of black paint, fixed as upper clamp to leg, complete all as specified, shown on drawings and as directed. FD-220

Material & labour for electric welding of long rails, short rails, legs of 32mm bore GI tubing by continuous welding around the broken joint duly painted with aluminium paint on welded portion complete all as specified & as directed. Notes :- (i) Unit for measurement of this item is ‘Each’ which shall comprise of welding of each broken joint all as specified above. (ii) Welding rods shall be ISI marked (iii) This item shall not be paid for serial item No. 7, 8, 9, 15, 17 & 18 here-in-before. FD-220

Gupta Suppliers

B K CONTRACTORS

M/s NIRMAN BUILDERS