Construction of Kitchen Block at Government General Hospital, Mahe.

Amount

Code No:2.8.1 Earthwork in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan),including dressing of sides and ramming of bottoms, lift upto 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed , within a lead of 50m - all kinds of soil.

Code No :2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50m and lift upto 1.5m.

Code No :2.27 Supplying and filling in plinth with river sand under floors, including watering ,ramming consolidating and dressing complete.

Code No: 4.1.3 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size).

Code No: 4.1.10 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size).

Code No: 4.8.1 Providing and fixing upto floor five level precast cement concrete hollow block,including hoisting and setting in position with cement mortar 1:3 (1 cement :3 coarse sand ) cost of required centering,shuttering complete - 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size).

Code No: 5.1.2 Providing and laying in position specified grade of reinforced cement concrete ,excluding the cost of centering ,shuttering , finsishing and reinforcement -All work upto plinth level 1:1.5:3 (1cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size).

Code No: 5.2.2 Reinforced cement concrete work in walls (any thickness) , including attached pilasters, buttresses , plinth and sting courses , fillets,columns , pillars , piers , abutments , posts and struts etc. upto floor five level excluding cost of centering , shuttering , finishing and reinforcement - 1:1.5:3 (1 cement : 1.5 coarse san :3 graded stone aggregate 20mm nominal size).

Code No: 5.9.1 Centering and shuttering including strutting , propping etc and removal of form for - foundations, footings, bases of columns etc for mass concrete.

Code No: 5.9.5 Centering and shuttering including strutting , propping etc and removal of form for - Lintels , beams , plinth beams ,girders , bressumers and catilevers.

Code No : 5.9.6 Centering and shuttering including strutting , propping etc and removal of form for - Columns , Pillars , Piers ,Abutments , Posts and Struts

Code No: 5.9.19 Centering and shuttering including strutting , propping etc and removal of form for -Weather shade , Chajjas, corbels etc., including edges

Code No: 5.9.20 Centering and shuttering including strutting , propping etc and removal of form for - Suspended floors , roofs , landings, balconies and access platform with water proof ply 12mm thick.

Code No: 5.12 Providing , hoisting and fixing upto floor five level precast reinforced cement concrete work in string courses, bands,copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but excluding cost of reinforcement , with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size).

Code No: 5.22.7 Steel reinforcement for R.C.C.work including straightening , cutting , bending , placing in position and binding all complete upto plinth level - Thermo-Mechanically treated bars (ISI BRAND OF APPROVED MAKE) Fe - 415 or more.

Code No: 5.33.2 Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work , using cement content as per approved design mix , including pumping of concrete to site of laying but excluding the cost of centering , shuttering ,finishing and reinforcement , including admixtures in recommended proportions as per IS : 9103 to accelerate, retard setting of concrete , improve workability without impairing strength and durability . Note:- Cement content considered in this item is @330 kg / cum. Excess or less cement used as per design mix is payable or recoverable separately. - All work above plinth level upto floor V level.

Code No: 5.35 Add for using extra cement in the items of design mix over and above the specified cement content therein.

Code No: 7.100.1 Laterite Stone Masonry for building work using neatly dressed Laterite Stone of size 30x20x20 cm in cement mortar 1:4 (1 cement : 4 Coarse sand ) for foundation and basement.

Code No: 7.101 Extra for laterite stone masonry superstructure above plinth level and upto floor five level.

Code No: 8.12 Providing and laying flamed finish granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18mm thick stone slab over 20mm (average) thick base of cement mortar 1:4 (1 cement : 4coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as - flamed finish granite stone slab Jet black , Cherry red, Elite brown, Cat eye or equivalent.

Code No: 9.1.2I Providing wood work in frames of doors , windows, clerestory windows and other frames , wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately) - Irul wood.

Code No: 9.33.4 Providing and fixing expandable fasteners of specified size with necessary plastic sleeves and galvanised M.S.screws including drilling holes in masonry work / C.C /R.C.C and making good etc.complete - 50 mm long

Code No: 9.53 Providing 40 X 5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30 x10x 15 cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Code No: 9.95.5 Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc.complete - 100 X 63 X 3.2 mm.

Code No: 9.96.2 Providing and fixing aluminium sliding door bolts , ISI marked , anodised ( anodic coating not less than grade AC 10 as per IS: 1868), transparent or dyed to required colour or shade , with nuts and screws etc complete - 250 X 16 mm.

Code No: 9.97.2 Providing and fixing aluminium tower bolts , ISI marked , anodised (anodic coating not less than grade AC 10 as per IS :1868) , transparent or dyed to required colour or shade , with necessary screws etc. complete - 250 x10 mm.

Code No: 9.121 Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness . The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S.stay shall be provided at the bottom to steady the frame.

Code No: 9.122.2 Providing and fixing to existing door frames - 30mm thick Fibre Glass Reinforced Plastic (FRP) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin , moulded to 3 mm thick FRP laminate all around , with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF) / Polystyrene foam to be used as filler material throuhout the hollow panel ,casted monolithically with testing parameters of F.R.P. laminate conforming to table -3 of IS : 14856 , complete.

Code No: 9.147A.3 Providing and fixing factory made uPVC white colour casement /casement cum fixed glazed windows comprising of uPVC multi-chambered frame , sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 + or - 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension , EPDM gasket , stainless steel (SS 304 grade) friction hinges , zinc alloy (white powder coated) casement handles, G.I fasteners 100 x8 mm size for fixing frame to finished wall , plastic packers , plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required)shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality , all complete as per approved drawing.(Single / double glass panes and silicon sealent shall be paid separately) - Casement window double panels with top fixed with S.S. friction hinges (350 x 19 x1.9 mm) made of (small series) frame 47 x50 mm , sash 47 x 68 mm & mullion 47 x 68mm all having wall thickness of 1.9 + or -0.2mm and single glazing bead of appropriate dimension – (Area of window upto 2.50sqm.) – Casement window size 1.20 x 1.80m.

Code No:11.3.1 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc .complete - 40mm thick with 20mm nominal size stone aggregate.

Code No: 11.36A Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer) , of approved make (Jhonson /Asian / Somany / Nitco) in all colours ,shades of size 200 x 300 mm as approved in skirting , risers of steps and dados,over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement with pigment of matching shade complete - size 200x300 mm.

Code No: 11.40.1 Providing and laying rectified ceramic rustic / matt finish floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer) of 1st quality conforming to IS:15622 of approved make (Somany / Nitco) in all colours ,shades, except white, ivory, grey, fume red brown, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigments etc., complete.

Code No: 11.46.2 Providing and laying vitrified tiles of size 600 x600 mm (thickness to be specified by manufacturer), with water absorption less than 0.08% and conforming to IS :15622 , of approved make , in all colours & shade, in skirting ,riser of steps , over 12 mm thick bed of cement mortar 1:3 (1cement :3 coarse sand), including grouting the joint with white cement & matching pigments etc.complete - size of tile 600x600mm.

Code No: 11.61 Providing and laying 22 mm thick factory made pre-polished cement concrete flooring tiles of required colour and design over 20 mm thick cement mortar 1:4 (1 cement : 4 sand ) and jointed with cement slurry mixed with an admixture of pigment to match the shade of the tile - (Endura \ Ultra \Dazzle \ Technic).

Code No: 12.41.1 Providing and fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS: 13592 Type A, including jointing with seal ring conforming to IS :5382, leaving 10mm gap for thermal expansion, (i) Single socketed pipes - 75mm diameter.

Code No: 12.42.6.2 Providing and fixing on wall face unplasticised - PVC moulded fittings /accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - shoe (plain) -110mm shoe.

Code No: 13.1.1 12mm cement plaster of mix -1:4 ( 1 cement : 4 fine sand)

Code No: 13.7.2 12mm cement plaster finished with a floating coat of neat cement of mix - 1:4 (1 cement :4 fine sand).

Code No: 13.47.1 Finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade - New work (two or more coats applied @1.43 ltr / 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg / 10sqm).

Code No: 13.60.1B Wall painting with plastic emulsion paint - Premium of approved brand and manufacture to give an even shade - two or more coats on new work.

Code No: 13.61.1 Painting with synthetic enamel paint of approved brand and manufacutre to give an even shade - Two or more coats on new work.

Code No: 16.68 Providing and laying 60mm thick factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction and of approved size and design / shape laid in required colour and pattern over and including 50mm thick compacted bed of course sand , filling the joints with coarse sand etc. all complete

Code No: 17.1.1 Providing and fixing water closet squatting pan (Indian type W.C.pan) with 100 mm Sand Cast Iron P or S trap, 10 litre low level white P.V.C flusing cistren, including flush pipe , manually controlled device (handle lever) conforming to IS : 7231 , with all fittings and fixtures complete , including cutting and making good the walls and floors wherever required. White vitreous china Orissa pattern W.C.pan of size 580x440mm with integral type foot rests.

Code No: 17.2.1 Providing and fixing white vitreous china pedestal type water closet (European type W.C.pan) with seat and lid, 10 litre low level white P.V.C. flusing cistern,including flush pipe, with manually controlled device (handle lever), conforming to IS: 7231,with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required - W.C. pan with ISI marked white solid plastic seat and lid.

Code No: 17.7.1 Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps ,32mm C.P.brass waste of standard pattern ,including painting of fittings and brackets ,cutting and making good the walls wherever required - white Vitreous China wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps.

Code No: 17.9.1 Providing and fixing kitchen sink with C.I. brackets, C.P. brass chain with rubber plug, 40mm C.P. brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required - white glazed fire clay kitchen sink of size600x450x250mm

Code No: 17.78.1 Providing and fixing CP brass health faucet of approved quality - 15 mm nominal bore.

Code No: 18.7.1 Providing and fixing Chlorinated Polyvinnyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete - internal work - exposed on wall - 15mm nominal outer dia pipes.

Code No: 18.7.2 Providing and fixing Chlorinated Polyvinnyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply,including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete - internal work - exposed on wall - 20 mm nominal outer dia pipes.

Code No: 18.7.3 Providing and fixing Chlorinated Polyvinnyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply,including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete - internal work - exposed on wall- 25mm nominal outer dia pipes.

Code No: 18.7.5 Providing and fixing Chlorinated Polyvinnyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply,including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete - internal work - exposed on wall -40mm nominal outer dia pipes

Code No: 18.48A Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI: 12701 marked , with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank - Circular Tank.

Code No: 18.51.1 Providing and fixing C.P.brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690gms - 15 mm nominal bore.

Code No: 21.17.2 Providing and fixing aluminium handle with lock of 75mm dia with necessary screws.

Code No: 21.17.3 Providing and fixing Anodised aluminium , minimum anodic coating of grade AC 15 grill of required pattern / design over the doors, windows and ventilators etc.,including fixing (but excluding the cost of the sections, which will be paid separately).

Code No: 22.20.1 Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3 mm thick water proofing membrane , black finished reinforced with non - woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre / sqm by the same membrane manufacture of density at 25 degree C, 0.87 -0.89 kg / litre and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parametres of the membrane shall be as under: Joint strength in longitudinal and transverse direction at 23 degree C as 650/450N/5 cm.Tear strength in longitudinal and transverse direction as 300 / 250N . Softening point of membrane not less than 150 degree C . Cold flexibility shall be upto- 2 degree C when tested in accordance with ASTM, D-5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane- 3 mm thick.

Code No: 30.26B Providing and laying filter media using HBG metal of 20 mm size to a required thickness.

Code No: 31.162.1B Providing, laying and jointing UPVC pipes(Finolex / jain / Supreme / Truebore / Nandi) (0.4 Mpa) conforming to IS specification 4985 and ISI marked including transportation to the site ,lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment, including cost of solvent cement,UPVC specials such as bends, tees, threaded pieces, couplers, reducer, endcaps etc.,complete all as per IS and CPWD specification. - 75mm dia.

Code No: 31.162.1D Providing, laying and jointing UPVC pipes(Finolex / jain / Supreme / Truebore /Nandi) (0.4 Mpa)conforming to IS specification 4985 and ISI marked including transportation to the site ,lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment,including cost of solvent cement,excluding UPVC specials such as bends,tees, threaded pieces, couplers, reducer, endcaps etc.,complete all as per IS and CPWD specification. - 110mm dia.

Code No: 31.177.1B Providing and fixing in position UPVC fabricated bend (Finolex / jain)(0.4 Mpa) conforming to IS 7834 part II and ISI marked,including labour charges for jointing, jointing materials etc,complete -75 mm dia.

Code No: 31.177.1D Providing and fixing in position UPVC fabricated bend (Finolex / jain)(0.4 Mpa) conforming to IS 7834 part II and ISI marked,including labour charges for jointing, jointing materials etc,complete -110 mm dia.

Code No:32.11.2.2 Constructing brick masonry manhole with 35 class designation bricks in cement mortar 1:4 (1 cement : 4 coarse sand ) R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand ) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) neatly finished complete as per standard design -inside size 90 x 80cm and 60cm deep including C.I. cover with frame (light duty) 455 x 610mm internal dimensions total weight of cover and frame to be not less than 38 kg. (weight of cover 23 kg. and weight of frame 15 kg.) - with bricks of class designation 35.