REPAIRS TO SECURITY WALL, CULVERT, PATHS, FENCING, BARBED WIRE AND CONCERTINA COIL, GLASS COPING ETC TO DMRL, ATC DEVATALAGUTTA, RCMA (MATT), DSC LINE ATC DEVATHALAGUTTA AND PCDA UNDER AGE B/R-II HYDERABAD

Amount

M&L for walling of squared rubble, brought upto courses, built in CM 1:4 including demolition of existing old stone masonry complete all as specified and directed.

M&L for walling of squared rubble, brought upto courses, built in CM 1:6 including demolition of existing old stone masonry complete all as specified and directed.

All as item No. 2 above, but except stones

M&L for Brick work with sub class 'B' bricks, straight or curved on plan exceeding 6m mean radius built in cement mortar (1:4) including raising height of existing manholes including demolition of old brick masonary complete all as specified and as directed.

M & L Brick work with sub class ‘B’ bricks straight or curved on plan exc 6 mtr mean radius using old size brick built in CM 1:6 including raising height of man holes from ground level including demolition of old brick masonary complete all as specified and as directed.

M&L plain Cement Concrete Type B0 1:2:4 (using 12.5 mm graded stone aggregate) cast in situ in lintels up to 1.5 M span, cills and other similar bands, plinth courses, parapets, copings, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating as directed including use and waste of form work including demolitions of old work complete all as specified and as directed.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc., including removal of rubbish off the premises, where directed and leaving the work clear of any plastering.

M & L for rendering 15mm thick in cement mortar (1:4) on fair faces of brick or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed.

Raking out joints to square rubble mas, coursed or uncoursed and M & L for Raised pointing in CM 1:3

M&L broken glass coping 25mm thick in CM 1:3 on top of wall including demolition of old coping complete all as specified and as directed.

M&L for boulder pitching, laid dry, hand packed tightly and grouted with cement sand mortar 1:6 including dismantling old boulder pitching complete all as specified and as directed.

Preparing new plastered surfaces and applying Two coats of cement base paint over a coat of alkali resistant primer on surfaces of walls complete all as specified and as directed.

Preparing surfaces plastered or unplastered old surfaces of walls and applying one coats of cement base paint complete all as specified.

S&F mild steel work such as angle iron in posts & struts in fencing including cutting tops to shape hand rail straight portion , drilled and contersunk for balusters , nosing to steps, struts in fencing including cutting tops to shape as directed , drilling holes, notching for wire etc flat iron fillets ( for securing chain link fencing ) including all necessary drilling, bolting or riveting etc and similar work conforming to Fe-290 Gde E-165 including dismantling old steel work complete all as specified and directed.

S&F framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc complete drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging also fastening and fixing complete including dismantling of steel work complete all as specified

S&F in repairs mild steel framed work such as grills, gratings etc with ends of bars shouldered and / or riveted or forged into spikes framed guard bars, ladders, framed balusters , walk ways, railing, framework or water tank and similar work conforming to Fe- 290 Gde E-165 all as specified

S&F Galvanized, 2 strand, steel barbed wire 2.24 mm dia., barbed with 2 mm dia., barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts, including securing or tying at crossings with and provision of galvanized mild steel pins etc., including taking down the existing wire complete as directed.

S&F in repairs Razor edge concertina coil, 750mm dia, consisting of spirals with sharp edged tape of 0.5mm thick, crimped to 2.6mm dia high tensile steel wire duly galvanized as per IS 4454 with scrapper barb having 51 spirals with 125 chips (when stretched to a length of 6 metre, weight of each coil shall be 8 to 9 Kg approximately) and fixed to MS frame work 'Y' shaped and placed at 1.5m apart and tied with GI staples/clips to retain horizontal including provision of necessary bolts, nuts etc. complete all as specified and directed. Make : Bengal sheet metal works, Kolkata/Armstrong wire.

Preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide zinc chrome primer.

Preparation of old painted steel surfaces of any description over 10 cm width or girth, not otherwise described and applying one coats of synthetic enamel paint (ordinary tint) complete all as specified and as directed.

Demolition of cement concrete (unreinforced ) in ground floors and pavings n. exc 15 cm thickness ( below or above ground level)

M&L for 75mm thick cement concrete type D-2, 1:4:8 (40mm graded aggregate) as in foundation, sub base for complete all as specified.

M&L 75mm thick cement concrete type B-2, 1:2:4 ( 40mm graded stone aggregate as in paths parking etc finished even and smooth without using extra cement complete

M&L 100mm thick cement concrete type B-2, 1:2:4 ( 40mm graded stone aggregate as in roads, hardstanding etc finished even and smooth without using extra cement complete

M&L Forming 12mm thick expansion joints for 100mm thick PCC filled with pre- formed bituminous filler and top 30mm primed and sealed with sealing compound Grade 'A' complete

M&L for Ready made speed breakers colour in yellow, black reflectors PMMA amber colour HIP reflected ( yellow , white) moulded in ABC alloy thickness, complete all as specified and directed. Make : DA-1009 of Dark eye or equivalent 3M/SIGMTECH/ DARK EYE / SIGNTECH

M&L for providing chequered cement concrete rubber moulded coloured tiles glossy factory made of hydraulic pressed finish of 25 mm thick and size not less than 300x300mm thick set and jointed in neat cement slurry in floors with grey cement and pigments and with 15mm thick screed bed or bedding layer in CM 1:6 including dismantling of old tiles and screed bed complete all as directed

M&L 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawn, drive ways or light traffic parking etc of required strength, thickness & size / shape , made by table vibratory method using PU mould , laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern finishing sweeping extra sand complete all as specified and including dismantling old tiles any description.

M&L repairing renewing cement concrete chequered tiles / inter locking tiles ISI Mark in patch, area n. exc 5 Sqm including removing and cleaning old tiles, preparing bed and laying or setting, jointing and pointing new or old tiles, including replaced damage tiles & providing PCC (1:4:8) 75mm thick sub base and 20mm thick CM 1:6 bedding layer complete all as specified and directed.

Excavating in post holes (or similar holes) each not exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25cm, watering, and removing surplus soil to a distance n.exc 50 m and making good surface in soft/ loose soil.

M&L for dismantling of Chain link fencing of any thickness complete all as directed

S&F chain link fencing of any type n exc 3.0 kg per Sqm including line wires, any mesh, size and type of standards, rails, straining bolts, etc., including provision of binding wire.

S&F mild steel round bars 10mm dia and over cut to length . bent to shape required for chain link fencing support complete all as specified

M&L for welding of existing damage / broken hinges, handle, frame and any other parts of gate, rolling shutters, fencing and adding angle to posts etc to achieve smooth function complete all as specified

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick with soils.

Removing Excavated soils exceeding 1.5 KM but not exceeding 5 KM and depositing where directed.

M & L plain Cement Concrete1:4:8 type D-2 (40mm graded aggregate) in foundation filling and mass concrete

Cleaning of drains by excavating of the filled earth. Vegetation and all foreign material average width 45 cm & avg depth 60cm and removing the excavated material to a distance exc. 50m and not exc. 250m complete all as directed.

M&L in repairs manufacturing, supplying and fixing retro reflective Mandatory/ Regulatory sign boards of 900 mm diametre with support length of 3750 mm and made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours).Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing , specification and direction of Engineer-in-charge.

Taking out carefully old disturbed / loose complete sign board of any size and height and refixing the same in position with PCC (1:2:4) including repairing and applying one coat of synthetic enamel paint complete all as specified

M&L preparation of old surfaces of bricks, stone, concrete of any description over 10cm girth or width not otherwise described and applying one coat of synthetic enamel paint complete

S&F 2mm thick fiber glass reinforced translucent plain sheeting with two corrugations / 10 cm side lap fixed with shelf tapping screws and washer in roof, wall etc complete all as directed

M&L for preparation of old decorated plastered / unplastered surfaces of walls, soffits of chajja, cornices etc and applying one coat of cement base paint upto three storey building including scaffolding arrangement all as specified.

Taking down carefully existing chain link fencing from post, refixing the post with PCC in base and refixing the same in existing position including replace damage nut and bolts complete all as specified

M & L for 18 to 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like including pointing white cement (1:2) using marble dust with admixture of pigment to match the shade of granite including cutting grooves and nosing including 15mm thick screed bed in CM 1:4 including dismantling existing granite work complete all as specified and directed.

M&L for 18 to 20mm thick polished granite work ( of any type) machine cut, in risers, skirting /dado fixed over 10mmthick rendering in CM 1:4 as backing coat and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone, including dismantling existing granite work complete all as specified.

Anjana corporation (BID ID -3101078)

Venkat Sai Enterprises (BID ID -3100677)

SRI SAI ENTERPRISES (BID ID -3099645)

Maruthi international (BID ID -3101023)

vvcenterprises (BID ID -3101332)

ELEVATORS MAINTENANCE ENGINEER WORKS (BID ID -3101491)

SUN LIGHT HOUSE (BID ID -3100791)