SPECIAL REPAIRS TO BLDG No AFII OF 316 MED REGT AND ADDN ALTN OF TOILET AND BATHROOM NEAR BLDG No P 13 OF 316 MED REGT AT AJMER MIL STATION UNDER GE NASIRABAD

Amount

Demolition of cement concrete (unreinforced ) in floors and pavings n. exc 15cm thickness (above or below GL) complete all as specified and directed

M & L for vitrified ceramic light shade tiles 10 mm thick (square/rectangular) polished area of each tile exc 0.36 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with colour of tiles over and including screed bed 15cm in CM (1:6) complete all as specified and directed.

M & L for vitrified ceramic light shade tiles in vertical surface 10 mm thick (square/rectangular) polished area of each tile exc 0.36 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with colour of tiles over and including 10mm thick CM (1:4) as in backing coat complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.06 Sqm but not exc 0.11Sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bedding in cement mortar 1:6 complete all as specified and directed.

M&L for glazed ceramic coloured tiles 7 to 8mm thick in vertcial surfaces of size exceeding 0.11 Sqm but not excceding 0.18 Sqm set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick screed plaster in cement mortar 1:4 complete all as specified and directed.

M&L for 25mm thick PCC (1:2:4) type B-0 using 12.5mm graded stone aggregate as in floors complete all as specified and directed.

M&L PCC (1:3:6) type C-1 using 20mm graded stone aggregate, 75mm thick as in plinth protection finished fair & even laid in alternative bays n. exc 2M in length and joints filled with bitumen mastic 1:3 complete all as specified and directed.

M & L for GI wire netting 0.63mm dia and 12mm mesh lathing to wood or metal studding joints etc in walls ceilings stanchions beams etc including all laps cutting and waste complete all as specified and directed.

Taking down cement or cement lime plaster or stone / brick wall, ceiling including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

M&L for rendering in cement mortar (1:6), 15mm thick on stone masonary surfaces or other than fair faces of brick work, finished even and fair, complete all as specified and directed.

M&L for preparation of old plastered surface ,scrubbing & removing existing treatment of walls and apply two coats of acrylic washable distemper over a coat of primer over coat of 1mm average thick wall putty complete all as specified & directed.

M & L for rough cast plaster mix with crushed stone (6-10 mm) sand and cement in the ratio 1:1:1 over 15 mm thick rendering CM 1:4 including two coat of cement base paint over a coat of primer complete all as specified and directed by Engr-in-Charge.

M & L for Rendering 15mm thick in CM 1:4 on stone masonary external surface finished even and smooth with out using extra cement complete all as specified and as directed.

M & L for rendering 5mm thick in cement plaster 1:3 on fair faces of brick work or concrete surfaces , in ceilings, chajjas, isolated width etc finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

M&L for preparation of newly plastered surface of wall and apply two coats of oil bound distemper over a coat of primer over and including 1mm thick coat of white cement based wall care putty, complete all as specified and directed.

M&L for prepration of old ceiling surfaces, applying one coat of white wash on ceiling complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sq. m each removing from site and making good disturbed surface of wall in CM 1:3, complete all as specified and as directed by the Engineer-in-Charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.5 sq. m but not exc 4 sq. m each removing from site and making good disturbed surface of wall in cm 1:3, complete all as specified and as directed by the Engineer-in-Charge

S & F 2nd class hardwood Chowkhats and frames plain solid , straight wrought, framed rebated on the solid rounded or chamfered, put together with glue, pinned at joints complete all as specified and directed.

S & F solid PVC door frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet & edges will be painted to match with printed sheet as reinforced with M.S. square tube and fixing in opening as per specification & drawing complete all as specified and as directed by the Engineer-in-Charge.

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supply & fixing in the frame at site as per specification & drawing.

S&F for 100mm size stainless steel butt hinge complete all as specified and directed.

M & L for rolled mild steel work angle iron as in door frame (Chowkhats) including provn of 10mm dia deformed bar welded horizontally to bottom of frame conforming to Fe-290 ( Gde 165-E ) including preparing back of chowkhat and applying two coats tar and sanding newly tarred surfaces with clean sharp sand complete all as specified and directed.

S & F hold fast of flat iron conforming to Fe-290 (Gde-E-165) including preparing the surfaces & treated with two coats for coaltar & sanded with clean sharp sand complete all as specified & directed

S&F Jet flush including plate & PVC connection complete all as specified and directed.

S&F 2nd Class Hard wood small fittings such as brackets of any type, latch and hinges blocks , shaped door and window stops and the like, including all necessary labours , article n.exc 200cu.cm each complete all as specified and directed.

S&F MS butt hinges, medium weight, cold rolled, ISI marked of size 50mm including necessary welding, complete all as specified and directed.

S & F brass body magnetic catches with striking plate including letting in complete all as specified and directed.

S&F continous (Piano) hinges, mild steel, bright finish, width of flaps (when open) 30mm complete all as specified and directed.

Add extra for 6mm thick external teak wood lipping 18/19mm and fixed with nails. complete all as specified and directed.

S&F hasp & staple 100mm size safety type, aluminium anodised with mild steel hinges pin including bolt of hinge plate & fixed with screws complete all as specified and directed.

S&F 100mm long extruded aluminium handles, cast type, anodised complete all as specified and directed.

S&F 150mm long extruded aluminium handles, cast type, anodised complete all as specified and directed.

S&F 150mm long aluminium anodised barrel tower bolts of extruded section, ISI marked all as specified and directed.

S&F 300mm long alumimium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolt and sliding bolt of extruded section or cast aluminium alloy all as specified and directed.

S&F new double action spring hinge, 125mm size, mild steel with steel wire spring, stove enameled black fixed to angle iron door frame by welding complete all as specified and directed.

S&F factory made Steel window/ ventilator glazed & gauged (combination) with side hung/ top hung shutters including box type / projecting type hinges, and steel peg stay, handle & locking arrangement and frame made out of 1.25mm thick pressed steel frame complete including necessary cooler arrangement in window & guard bars all as shown in drg No. CEBZ/TD/14/11 sheet No 1/7 to 7/7 & specified.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of apertature 1.40mm and fixed with tinned tacks or stainless steel wire staples all as specified and directed.

S&F for 3mm thick sheet glass plain / pin headed, ordinary quality and glazing with oil putty in square n. exc 0.50 Sqm in each pane complete all as specified and directed.

M&L for preparation of new or previously untreated wood and wood based surfaces of any description not otherwise descriped over 10cm width girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surfaces over 10 cm width or girth & applying two coats of synthetic enamel paint of 1st quality over a coat of red oxide primer complete all as specified and directed.

S & F 20mm dia, aluminium anodised tubular curtain rail as fixed in repairs complete all as specified and as directed by the Engineer-in-Charge

S & F aluminium anodised brackets for tubular curtain rail 22mm dia as fixed in repair complete all as specified and as directed by the Engineer-in-Charge

Taking down existing tar felt or of any description including cement plaster or concrete of any thickness from the roof surfaces of building including cleaning the surfaces in all respect & preparing it for further treatment & removing rubbish from site complete all as specified and directed.

M&L for rendering 10mm thick in CM 1:4 mixed with water proofing compound @ 3% by weight of cement on fair faces of RCC/stone patti roof surfaces finished even & smooth without using extra cement complete all as specified and directed (WPC will be measured and paid separately).

Supply only Integral water proofing compound of approved quality and make confirming to IS complete all as specified and directed.

M&L for coved fillet in PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate at junction of roof & parapet wall and other vertical surfaces 75mm radius and surface painted with a hot paving bitumen grade 30/40 conforming to IS-73 @0.70 Kg/Sqm over a coat of bituminous primer conforming to IS-3384 @ 0.30 Ltr Sqm complete all as specified and directed

M&L roof treatment with APP modified polymeric water proofing membrane, 3mm thick having centre core not less than 100 micron high molecular high density polyethylene film (HMHDPE) protected on both sides with high polymeric asphaltic mix and 20 mircron HMHDPE film weight not less than 3.00 kg/ Sqm applied with bonding material using blown type bitumen primer Grade 85/25 @ 1.20 Kg/Sqm over bitumen primer conforming to IS -3384 @ 0.40 Kg /Sqm with final coat of bonding bitumen grade 85/25 @ 1.20 Kg /Sqm over APP membrane with all overlaps complete all as specified and directed

Material and labour for 40mm thick (avergae consolidated thickness) PCC (1:2:4) type B-0 using 12.5mm graded stone aggregate laid in slope as in padding, finished even and smooth on existing slope including provision of 'V' shaped groove 6mm wide and 10mm deep at 1.20 metre interval or parts thereof, both ways on top of PCC padding and filled with mastic bitumen of (1:1) proportion complete all as specified and directed.

M& L 16 to 18mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in CM(1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including necessary bull nosing to edging fixed over 15 mm thick Screed in CM (1:4) complete all as specified and directed.

S&F of for ISI Marked 20mm dia Ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and as directed by the Engineer-in-Charge.

Taking down old unserviceable 15mm GI tubing, fittings and connections and removing from site or keeping aside for refixing complete all as specified and directed.

Refixing old 15mm GI tubing galvanised with new fittings and fixed to walls, ceiling or laid in floors, trenches including necessary cleaning, cutting, screwing complete all as specified and directed.

S&F 15mm GI water tubing, medium grade, galvanised with all fittings ( and fixed to walls, ceiling or laid in floors/ trenches complete all as specified and directed.

Taking down old unserviceable 20mm GI tubing, fittings and connections and removing from site or keeping aside for refixing complete all as specified and directed.

Refixing old 20mm GI tubing galvanised with new fittings and fixed to walls, ceiling or laid in floors, trenches including necessary cleaning, cutting, screwing complete all as specified and directed.

S&F 20mm GI water tubing, medium grade, galvanised with all fittings ( and fixed to walls, ceiling or laid in floors/ trenches complete all as specified and directed.

Taking down old unserviceable 25mm GI tubing, fittings and connections and removing from site or keeping aside for refixing complete all as specified and directed.

Refixing old 25mm GI tubing galvanised with new fittings and fixed to walls, ceiling or laid in floors, trenches including necessary cleaning, cutting, screwing complete all as specified and directed.

S&F 25mm GI water tubing, medium grade, galvanised with all fittings ( and fixed to walls, ceiling or laid in floors/ trenches complete all as specified and directed.

S&F in repair 25mm bore gun metal, globe or gate valve with iron wheel head, screwed both ends for iron pipes and fixed complete all as specified and directed.

S&F in repair 20mm bore gun metal, globe or gate valve with iron wheel head, screwed both ends for iron pipes and fixed complete all as specified and directed.

S & F in repair of ISI marked 15mm bore stop valves/angle valve concealed cast copper alloy, chromium plated with long shank and cup , screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified.

S & F in repair of ISI marked 15mm bore stop valves/angle valve cast copper alloy, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified.

S&F in repairs 15mm bore cast copper alloy chromium plated ISI marked bib tap with crutch or butterfly handle, screwed down, screwed for iron pipe complete all as specified and directed.

S&F in repair Brass chromium plated shower rose 125mm size with arms with or without swivel joints, including fixing to steel pipe or union complete all as specified and as directed.

S & F for brass chromium plated soap dish, fixed to plugs with chromium plated brass screws complete all as specified and as directed by the Engineer-in-Charge.

S&F 15mm dia pillar taps cast copper alloy with capstan heads, cromium plated screwed down high pressure with or without lettered Hot or Cold with long screw shanks abd fly -nuts screwed for iron pipe and fixed complete all as specified and as directed by the Engineer-in-Charge

S & F tubular towel rail of brass Chromium plated, 20mm dia, D type 60cm long between flanges including Chromium plated brass screws and wooden/plastic cleats complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair for vitreous China wash basin, white, flat back, size 550x400mm including PVC connections 15mm size with PTMT nuts of length 450mm, 40mm PVC waste pipe of suitable length, brackets, and cutting for and pinning in ends of brackets or erecting stand complete all as specified and as directed by the Engineer-in-Charge.

S & F in repair 15mm bore ISI marked cast copper alloy chromium plated mixing valve with hot and cold water with crutch handle of approved quality for WHB complete all as per specified and directed.

S&F in repair for vitreous china wash down water closet pedestal pattern pan white with trap including connection to existing out joint pipe, flushing pipe or Cistern, antisyphonage pipe, including making, etc complete including making goood to floor etc complete all as specified and as directed.

S&F in repair PVC valve less, syphonic action type flushing cistern, 10 Litre capacity, low level, white with inlet, ball vlave float, handle including PVC rigid pipe 32mm bore as flush pipe fixed on walls by drilling holes and using PVC rawl plug of suitable size complete all as specified and directed.

Supply and fixing in repairs PVC cabinet of size 350 mm x 450 mm with mirror of good quality with shelves in bath fixed complete to walls complete all as directed by Engineer-in-Charge.

S&F in repair 1mm thick stainless steel kitchen sink with drainage board with plugs, washers and waste coupling and PVC waste pipe including fixing on half brick wall or cantilever brackets(angle iron ) and connecting union overall size 915mm x 460mm, bowl size 410mm x 330mm x 160mm, , complete all as specified and directed

S&F stainless steel plate rack made of 0.63mm thick of over all size 765mm x 920 mm x 220 mm and weight not less than 8.00 Kg each of approved quality complete all as specified and directed..

Taking down of PVC rainwater pipes and waste water pipe or gas pipe (any size or pattern) in any position , including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to store complete all as specified and as directed by the Engineer-in-Charge.

S&F 110mm PVC (SWR) pipes single socketed in any length with rubber joints fixed to wall or laid in floors / trenches with & including existing / new MS stack clamps of FI 50 x 3mm complete all as specified and directed.

S&F 75mm PVC (SWR) pipes single socketed in any length with rubber joints fixed to wall or laid in floors / trenches with & including existing / new MS stack clamps of FI 50 x 3mm complete all as specified and directed.

S&F 110mm bore PVC (SWR) bend / shoe of any radius with access door, complete all as specified and directed.

S&F 75mm bore PVC (SWR) bend / shoe of any radius with access door, complete all as specified and directed.

S & F PVC 110mm bore (SWR) branch piece, double (double Y) with access door equal or unequal, complete all as specified

S & F for 110mm bore PVC (SWR) junction double (double T) with access door equal or unequal, complete all as specified

S&F in repairs 110mm bore PVC (SWR) vent cowl complete all as specified and direted pleases.

M & L for PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and as directed by the Engineer-in-Charge

S&F PVC (SWR) floor trap/ Nahani trap 75mm, plain with grating including jointing to waste pipe fixed in cement concrete type (1:2:4) complete all as specified and directed.

S&F mild steel framed work such as grills, grating cooler stands, etc, with ends of bars shouldered and / or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railing, frame work of water tanks and similar work conforming to Fe 290 Gde E-165 complete all as specified and directed.

Demolition, reinforced cement concrete roofs, floors (other than ground floors), beams, staircases, landing, parapets, chajjas, and similar suspended work cut as required to facilitate demolition complete all as specified.

M & L for RCC 1:2:4 Type B0 using 12.5mm graded aggregate as in beams, cantilevers, bressummers, parapets, chajjas, lintels over 1.5m span etc, including formwork complete all as specified.

M & L for mild steel TMT bars of 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Demolition of brick work or stone masonary built in cement mortar etc complete all as specified and directed.

M & L for brickwork with fly ash bricks, in straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and as directed by the Engineer-in-Charge

M&L for brick work with flyash bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed.

S&F 2nd class HW 35mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated. complete all as specified and directed.

M&L 100mm thick cement concrete type D-2 1:4:8 (40mm graded stone aggregate ) as in floors / pavings complete all as specified and directed.

M&L for factory made 60mm thick machine pressed precast cement concrete coloured, reflective type interlocking paver blocks of Grade M-35 conforming to IS 15658-2006 of shape and size as directed with grey cement and pigment laid over & including 25mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as specified & directed.

Fabrication & fitting of cabinet / shelves & wardrobe / cupboard made out nof 18mm thick (one side decorative lamination & other side balancing lamination ) PVC sheet with piano hinges including providing cabinet for keeping baskets / cutlery basket with handles door shutters all as specified and directed. Note : PVC sheet, fittings & fixture will be measured and paid separately).

Supply only 18mm thick (one side decorative lamination & other side balancing lamination sheet) solid PVC board of make : Rajshree or equivalent all as specified and approved by Accepting Officer with cement solvent adhesive for shutter / cup boards / partition wall / wall cabinet and similar work complete all as specified and directed.

Supply only soft close clip on hinge bright finish complete all as specified and directed.

Supply only 125mm dia oval shape brass handle fancy type bright finish complete all as specified and directed.

Disconnecting & taking down the existing unserviceable water tank and Supply and fixing 1000 Litre capacity white colour rotational moulded polyethylene water storage tanks triple layered (cylindrical vertical with closed top) , hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

Disconnecting & taking down the existing unserviceable water tank and Supply and fixing 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

S & F false ceiling with Everest Fibre Cement Designer tile Ivory painted (High Pressure Steam Cured) of 4mm thickness(as per IS: 14862) of size 595x595 mm and any one of the desin (occeanic, lake & hill, cascade or electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length, and 15x32mm made from 0.30 mm thick sheet, and cross "T" of size 15x32mm made of 0.30 mm sheet, spaced between main "T" at 600mm c/c to form a grid of 600X600mm and wall angle of size 15x20mm made of 0.30 mm thick sheet and laying false ceiling tiles in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixures,smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing rafter, purlin,etc with dash fasteners,GI adjustable rods of 3mm dia with gavanised Butterfly level clips, spaced at 1200 mm c/c along main T, bottom exposed width of 15mm of all T-sections shall be centra black pre-painted with polyester paint, and having a load bearing capacity of 12 kg/sqm, all complete at all height and dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

M&L for preparation of new plastered surfaces of Walls and applying three coats of white wash complete all as specified and directed

M&L for preparation of newly plastered surface of ceiling and applying three coats of white wash complete all as specified & directed.

M&L for newly plastered surfaces two coats of cement base paint over one coat of cement based primer on plastered/ concrete surfaces of walls including preparation of surfaces complete all as specified and directed.

M&L for PCC 1:2:4 Type B-1 (using 20mm stone crushed agg.) as in rounded or chamfered on edges in any description complete all as specified.

M&L for non skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.11 Sqm but not exc 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bedding in cement mortar 1:6 complete all as specified and directed.

M&L PCC (1:3:6) type C-1 using 20mm graded stone aggregate, 50mm thick as in plinth protection finished fair & even laid in alternative bays n. exc 2M in length and joints filled with bitumen mastic 1:3 complete all as specified and directed.

Taking out old u/s water closet and S&F vitreous China "Orissa pattern" size 580 x 440mm" white, with intergral foot rests with vitreous china 'P' or 'S' trap front or back inlet including connection to trap and to flushing pipe, anti syphnage pipe and making good the floor to match the existing complete all as specified and directed.

S&F in repair PVC connection, heavy duty 15mm bore, 45cm long with 2 Nos PTMT nuts of approved quality complete all as specified and directed.

S & F of vitreous China urinal, flat back, half stall type white/ ivory colour with grating and Union for discharge pipe. Including connection to flushing pipe and outgoing waste pipe complete all as specified and as directed by the Engineer-in-Charge.

S & F in repairs grating square/round 125mm size of PTMT with centre hole movable or side hole for fix to waste pipe (minimum weight 50 gms) complete all as specified and directed.

S&F in repairs CI Nahani/Floor trap 75 mm outlet,with grating including jointing to waste pipe fixed in cement concrete type B1(1:2:4), complete, all as specified & directed..

M&L 50 mm thick sand stone slabs; set and jointed over joists etc. in CM 1:4 as in base of water tank and M&L 25 mm thick PCC 1:2:4 type B-0 (using 12.5mm stone crushed agg.) finished concrete surfaces even & smooth complete all as specified and directed

Taking down CI pipe 100/75 mm fixed wall and floor etc including accessories complete all as specified and directed.

S&F CI soil and waste pipe 100mm bore waste or vent pipe in any length with or without ears, with cement joints on vertical surfaces of wall complete all as specified and directed.

Fixing only 100 mm bore CI pipe as on wall, complete all as directed.

S&F CI soil and waste pipe 100mm bore waste or vent pipes single socket in any length with cement joints laid in floor or in trenches complete all as specified and directed.

S&F CI soil and waste pipe 75mm bore waste or vent pipes single socket in any length with cement joints laid in floor or in trenches complete all as specified and directed.

S&F CI soil and waste pipe 100mm bore waste or vent pipes single socket in any length with or without ears, with cement joints on vertical surfaces of wall complete all as specified and directed.

S & F 75 mm CI bend, fixed with cement solvent complete, all as specified and directed

S & F 75 mm CI bend, fixed with cement solvent complete, all as specified and directed

M&L for reinforced cement concrete M-25 grade (Nominal mix) using 20 mm graded crushed stone aggregate in slabs supported on walls, beams and columns in floors, roots, shelves and the like complete all as specified and directed.

M & L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), flat surfaces of concrete , surface is required to be fair finished complete all as specified and as directed by the Engineer-in-Charge.

M & L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide, as roughed finished surface of concrete complete all as specified and as directed by the Engineer-in-Charge.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fittings such as switches, ceiling roses, holders, regulators, sockets etc., removing materials from site and making good disturbed surface of walls, floors etc.

Disconnecting unserviceable sub main wiring/service connection of any size and including conduit of any type and accessories and removing from site and making good the disturbed surfaces.

Taking down MCB DB's complete with MCB's/Isolator etc removing materials from site and making good disturbed surface of walls, floors etc.

M&L for point wiring with 1.5 Sqmm, PVC insulated, unsheathed, multi stranded copper conductor single core FRLSH cable, IS-694 marked, drawn through and including non metallic rigid PVC concealed conduit 20mm dia or higher complete with all PVC conduit accessories such as socket, elbow, Modular junction box, bell mouth, reducer, bend and flexible conduit etc./ fittings ISI marked and sunk type pressed steel anodised terminal box 1.2 mm thick for moduler switch/socket fitting, brass screws and cup washers including 1.5 Sqmm multi stranded copper conductor PVC insulated green in colour as continous earth conductor connected to common earth and earth dolly with modular frame plate all accessories complete all as specified and directed

One light point/bell point controlled by one, one way switch.

One ceiling fan/exhaust fan point controlled by one, one way switch.

One three pin 5 Amp socket on same board with other switches.

One 3 pin 5 Amp socket on independent board.

All as per item No. 131.00 here-in-before but with 2.5 Sqmm, for one 5 pin 5/15 Amp socket on independent board including 2.5 Sqmm stranded copper conductor (FRLS) PVC insulated green in colour as continous earth conductor connected to common earth.

S&F of sub main wiring with two runs of single core PVC insulated and unsheathed multistranded (FRLS) copper conductor cable of size 6.00 Sqmm LT, 1100 volts grade, drawn through and including 25 mm dia or higher PVC non metallic concealed conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 6 sqmm single core multistranded copper conductor cable green colour as earth continuity conductor.

S&F of modular switch 1 way 6 Amp , 1 module, complete all as specified and directed.

S&F modular switch 1 way 16Amp, 1 module, complete all as specified and directed.

S&F modular socket 6Amp, 2/3 pin combined 2 module complete all as specified and directed.

S&F mdoular socket 6Amp/16 Amp, 2/3 pin combined 2 module complete all as specified and directed.

S&F ceiling fan regulator electronic flush , steped (four step) 230 Volts AC complete all as specified and directed.

S&F ceiling rose surface bakelite 3 terminals 63.5 x 17 mm complete all as specified and directed.

S&F of lamp holder PVC/polycarbonate type with back plate complete all as specified and directed.

S&F LED tube light fitting in acrylic linear tube (1x 18 watt),230V for single LED tube light including 1 x 18 W LED retrofit bar professional CW 6500 K cover channel, bipin holders,LED power driver, connector block, etc complete with all accessories internally prewired and including connecting up with three core flexible copper conductor cable with suitable size for connection of fitting from ceiling rose complete all as specified and directed.

Supply and fixing LED light fitting mirror type with high output diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete

S&F LED bulk head luminaire 1x 10 W bulk, IP 65 protection complete with all accessories and including connecting up with three core copper conductor cable complete all as specified and directed.

Supply and fixing testing and commissioning energy saving street light luminaire 35 watt LED , pressure die cast housing with epoxy powder coated with colour finish and prismatic poly carbonate coverlic cover complete, IP 66 protection including connecting with three core copper flexible wire from ceiling rose to connector of light fitting complete all as specified and directed by Engr-in-Charge.

Supply and fixing street light bracket made of 32 mm GI pipe, 1.2 mtr length fixed with two Nos of clamp, nut and bolts complete all as specified and directed.

S&F of MCB distribution board TPN 4 way, 415 volts, double door, with 200 Amps rated bus bar, neutral bar with shrouds, earth bar, IP-43 , made out of sheet steel enclosure, recessed type, factory made powder coated suitable for housing MCBs as incomer and outgoing complete all as specified and directed.

S & F of MCB SP, 240 volt, 6 Amp to 40 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

S & F of MCB SPN, 240 volt, 63 Amp capacity, 10 KA , 'C' curve complete all as specified and directed.

S&F of MCB TPN, 415 volt, 63 Amp capacity,10 KA, 'C' curve complete all as specified and directed.

S&F of MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door IP-42 DB's , made out of sheet steel enclosure, recessed type, factory made powder coated 8 way, 240 volts suitable for housing MCB's complete all as specified and directed.

S & F of MCB SPN, 240 volt, 32 Amp capacity, 10 KA , 'C' curve complete all as specified and directed.

Supply and fixing in repair surface mounted LED downlight 18 watt round shaped , Slim surface mounted LED panel with premium diffuser to ensure glare free & even light distribution complete all as specified and directed. Make Havells, Model -Trim Cosmo Surface Round, Cat Part No LHEAAHP7IL1W018, or equivalent model of Philips/Compton

Supply and fix exhaust fan, steel body AC single phase, 230V of size 300 mm sweep with blades and frame and louvers complete fixed and opening of wall with suitable MS bolts, grouted to wall and connecting up including provision of cable from connector to fan with flexible cable 24/0.2mm with copper conductor and necessary fitting arrangements complete all as specified and directed at site. Make - Havells/ Bajaj / Philips.

Supply and fix ventilation fan, steel body AC single phase, 230V of size 250 mm sweep with blades and frame and louvers complete fixed and opening of wall with suitable MS bolts, grouted to wall and connecting up including provision of cable from connector to fan with flexible cable 24/0.2mm with copper conductor and necessary fitting arrangements complete all as specified and directed at site. Make - Havells/ Bajaj / Philips.

M&L for earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground vertically to a depth not less than 2.25m below ground level with top edge of the earth plate at a depth not less than 1.5m below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and other end of earth wire connected to main switch board and protected by galvanised iron pipe light grade 15mm bore and water pipe 20 mm bore GI med grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 and RCC cover with handle all as specified and shown in elect plate No 3 of SSR Part-I of 2009 incl dismantling of old unsv existing earthing complete all as specified and directed.

S&F of sub main wiring with two runs of single core PVC insulated and unsheathed multistranded (FRLS) copper conductor cable of size 2.5.00 Sqmm LT, 1100 volts grade, drawn through and including 25 mm dia or higher PVC non-metallic concealed conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 2.5.0 sqmm single core multistranded copper conductor cable green colour as earth continuity conductor complete all as specified and directed. Note :- Two run of single core cable, one run of earth continuity conductor & conduit with conduit accessories shall be measured as one unit length complete all as specified and directed.

Supply & Fixing of coaxial cable wire for TV complete all as specified and directed.

Supply & Fixing of coaxial socket for TV complete all as specified and directed.

S&F LED lamp 9/10 watt suitable for 230 volts, 50 Hz B-22 Base complete all as specified and directed.

Supply & fixing ceiling fan 1200 mm sweep , 230 Volts, AC , 50 Hz, copper winded motor, BE star rated white colour complete with motor, blade set of three nos , down rod, canopy, shackle assy complete all as specified and directed.

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, 5 Star rated & Glass lined enamel coated incoloy heating element, Temperature indicating dial & Shock-resistant ABS outer body complete with all accessories such as safety valve, thermostate, NRV, connection piece etc complete all as specified and directed. Make: Bajaj, Havells, Usha.

S&F recess mounted 2' x 2' LED luminarie 36 watt, cool day/warm light with white powder coated CRCA housing with LED driver, efficiency>100 Lm/w complete all as specified and directed. Make Crompton/Havells/Philips.

S & F single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole 20 Amp MCB SP `C' series for AC complete all as specified and directed.

S&F Wall mounted decorative luminaire fitting suitalble for LED lamp B-22 base 9 watt complete all as specified and directed by Engr-in-Charge. Make:- Havells/Mepro/Philips

M&L for point wiring with 1.5 Sqmm, PVC insulated, unsheathed, stranded copper conductor single core FRLS cable, IS-694 marked, drawn through and including non metallic rigid PVC concealed conduit 20mm dia or higher complete with all PVC conduit accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc./ fittings ISI marked and sunk type pressed steel anodised terminal box 1.2 mm thick with bakelite laminated sheet top cover 3 mm thick, brass screws and cup washers including 1.5 Sqmm stranded copper conductor PVC insulated green in colour as continous earth conductor connected to common earth and earth dolly with all accessories for:-

One light point controlled by two Nos two way switch.

One exhaust fan point controlled by one, one way switch.

All as per item No. 165.00 here-in-before but with 2.5 Sqmm, for one 5 pin 5/15 Amp socket on independent board including 2.5 Sqmm stranded copper conductor (FRLS) PVC insulated green in colour as continous earth conductor connected to common earth.

S&F switch piano flush type 5 amps, single pole one way 240 volts complete all as specified and directed.

S&F switch piano flush type 15 amps, single pole one way 240 volts complete all as specified and directed.

S&F socket out let 2 in 1,multipurpose 3 pin 15/16 Amp flush type ISI marked complete all as specified and directed.

S&F distribution board single pole & neutral with 200 Amps rated insulated bus bar, double door, IP-43, DB's made out of sheet steel enclosure, recessed type, factory made powder coated, 04 way, 240 volts suitable for housing MCB's and isolator's complete in all fixing material/accessories etc complete all as specified and directed.

S&F of 1100 volts grade heavy duty cable PVC insulated aluminium conductor served with inner sheating of PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than one meter apart including 4 mm suspension wire one twin core cable 2 core flat of 10 sqmm size complete all as specified and directed.

Supply and laying including jointing, testing or fixing or passing through pipe, trench or duct commissioning and testing XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100 volt grade size 50 sqmm, 3.5 core complete all as specified and directed by Engineer-in-Charge.

Supply and fixing tubes light grade GI tubing 40 mm dia with all fitting laid in trenches/on wall complete all as specified and directed by Engineer-in-Charge.

Excavating in trenched not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. or for cable laying or not exceeding 10 sqm on plan and not exceeding 1.5 m in depth and getting out in soft/ loose soil complete all as specified and as directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in any type of soil, complete all as specified & directed.

M & L for removing excavated soils n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and directed.

Supply & spreading in trenches dry river sand cushioning to underground cable in trenches including spreading, levelling hand punning down complete all as specified and directed Note:- Depth of sand cushioning will be measured after punning down and levelling the sand properly.

M & L for laying of bricks locally available sub class 'B' bricks, non-modular sizes as per IS 1077: 1992 for cable protection cover laid flat and dry in trenches over the cable perpendicular to the direction of cable all as directed.

MAHARANI CONSTRUCTION

TARA CHAND JI GOMA CONSTRUCTIONS CO.

M/s SUNIL ENTERPRISES

JWALA ENTERPRISES

Shree Sai Ram Enterprises

BSB CONSTRUCTION COMPANY