SPECIAL REPAIR TO DSC OFFICE AND BILLETS AT AF STN BARNALA UNDER GE AF HALWARA

Amount

Demolition of cement conrcete of any description and in any position not otherwise specifically provided complete all as specified and directed.

Roughening surfaces of old concrete roofs by backing sweeping clean with iron brush and washing down with water etc and applying neat cement slurry @ 3.00 kg/Sqm complete all as specified and directed

M&L 40mm thick (Avg thickness), PCC(1:2:4) type B1, (using 20mm graded stone aggregate) finish even and smooth with using extra cement complete all as specified.

M&L for PCC 1:2:4, type B-1 (using 20mm graded stone aggregates) as in roof kerbs/mud stops complete all as specified and directed.

M&L for 15 mm thick screed bed in cement mortar 1:3 mixed with water proofing compound by 3% by weight of cement or as per manufacturers instructions complete all as specified and directed Note :- Water proofing compound will be measured and paid seperately.

Supply only Integral waterproofing compound

Demolition of cement concrete in floors and paving n.exc 15cm thickness (below or above ground level) complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6, type C-2 (using 40mm graded stone aggregates) as in plinth protection finished even and smooth without using extra cement complete all as specified and directed.

Taking down cement plaster on brick walls built in cement mortar including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed

Preparation of roof top surfaces providing and applying single component elastic cold applied polyurethene modified acrylic roofing system ,co elastic technology (CET) based on modified polyurethene and fully fibre reinforced having sun Reflectivity index (SR) of 106 on top of concrete roof surfaces all cracks upto 3mm at corner joints channel and parapets should be treated with crack seal . Applying three coats including one coat of primer of Shali urethene BTD/Sikalastic 560/smart care damp proof ultra having coverage @ min 0.75Kg/Sqm and dilution upto 10% and laying reinforced fibre net and applying two coats of shaliurethene BTD/Sikalastic 560/smart bcare damp proof ultra @ total consumption 2Kg/sqm in two coats for maintaining minimum dry film thickness 1.50mm and elongation at break of free film of approx 350% The material shall be applied with brush or rooller ,complete in all respect as per the direction of Engineer -in-Charge /Consultant (Note :6hrs interval between two coat will be maintain ) All auxillary and accessories involved during application should be supplied by single manufacturer as part of system . Make STP/Sikka/Asian paint or equivalent as approved by GE. i)The water proofing treatment shall be got carried out by the manufacturer or their authorised applicators duly approved by GE in writing. ii) 5% amount of the total amount of water proofing treatment shall be retained as a guarantee and shall be released after 10 years . However contractor may deposit the FDR of same amount in favour of Ge . If contractor fail to rectify the defect pointed out during this period in writing , the defect shall be got rectified at contractor " risk and cost and the payment shall be made from the amount of kept reserved or by encashing the FDR deposited by the contractor as guarantee. the contractor's quoted rates for this item shall deemed to be inclussive of this aspect.

M&L for 15mm thick cement plaster in cement mortar (1:4) on fair faces of brick work or concrete surfaces finished fair and even without using extra cement complete all as specified.

M & L 10mm thick cement plaster in cement mortar (1:6) on fair faces of brick work or concrete surfaces finished even & smooth without using extra cement complete all as specified.

M&L for 5mm thick cement plaster in cement mortar (1:3) on ceiling surfaces finished even and smooth without using extra cement complete all as specified.

M&L for preparation of new plastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distember over a coat of primer complete all as specified and directed.

M&L for preparation of old treated plastered/unplastered surfaces by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots, filling holes & cracks with cement or white putty and applying Two coats of white wash on walls complete all as specified and as directed.

All as per item No. 16 here in above but on ceiling

M&L for preparation of old decorated plastered & unplastered surfaces of walls by brooming down or steel wire brushing, scrapping down smoke soot, mould, moss and efflorescent salts trading oil and greasy spots, filling holes, cracks with cement base putty and applying two coats of distemper oil emulsion complete all as specified.

M&L for Mild steel curtain rod powder coated with fixing side brackets, end cups, rings @ 10 Nos per running metre and fixed with PVC rawl plugs & steel screws as in repairs complete all as specified.

Taking down chowkhat / frames with shutter (without taking off shutter from frames) n.exc 1.5 Sqm each complete all as specified and directed. Note : Distrubed surface of wall shall be make good by the contractor. The rate quoted shall be deemed included for the same)

All as per Sl item No 20 above but exc 1.5 Sqm but not exc 4 Sqm each.

S&F factory made pressed steel frames made out from 1.25mm thick steel sheet for doors of size 125x60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc.and including treated with tar or coal tar black paint on steel surfaces in contact / embeded in concrete or masonary work including filling hollow portion of frames with PCC 1:3:6 type C-0 (using 12.5mm graded stone aggregates) complete all as specified and directed.

S&F factory made, 35mm thick, 2nd class hard wood (Hollock), plain framed, panelled shutters, any number of panels, panels shall be of 12mm thick BWR glade veneered particle board medium density, wood particle board with commercial face veneers, size of members as specified in clause 8.20(a) of MES Schedule Part-I section-8 complete all as specified.

S&F factory made 35 mm thick, 2nd class hard wood (Hollock), glazed and skeleton shutters open rebated and prepared to receive glass/ gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut and mitered beads for securing glass etc for doors, size of members as specified in clause 8.24 (a) of MES Schedule Part-I Section-8, complete all as specified.

S&F small fitting of 1st class hard wood any shape not exceeding 200cu.cm, as for door stopper, cleat etc. or similar articles complete all as specified and directed.

S&F aluminium anodised, barrel tower bolts of extruded section with length of bolt 200 mm and fixed complete all as specified and directed

S&F 300mm long Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S&F Aluminium anodised Cast type handle of 150mm size.

S&F 300mm long Mild steel , ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S & F factory made Box type steel window, double shutter (glazed and wire gauzed) with side hung shutters including box type hinges, steel handles fabricated type for each leaf duly welded, mild steel barrel tower bolts 150mm size (02 Nos for each leaf) duly welded, complete with glazing bars dovetailed or welded including MS fillets, including provision and welding of guard bars including one shop coat of red oxide primer over window, frame & guard bars complete all as specified and directed. Notes: - (i) Windows shall be fabricated as per HQ CE Chandigarh Zone drawing No. TD-219 Sh 1/3 to 3/3 dated 02 Jan 2007 with one amendment dated 22 Jun 07 in Sh 1/3 and dt 15 Jun 07 in sh 2/3 & 3/3 and these drgs may be referred from GE office or from the office of CWE (AF) Ambala. (ii) Glazing, Wire cloth and guard bars shall be measured and paid separately as Supply only. (iii) The term double shutter stated is meant for providing glazed shutter as well as wire gauged shutter on outside & inside of the frame respectively.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqmin each pan complete all as specified and directed.

M&L for preparation of new steel surfaces of girth exceeding 10 cm and applying 2 coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new wooden surfaces of girth exceeding 10 cm and applying 2 coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Supply only framed work such as grills gratings, etc, with ends of bars shouldered and/ or riveted, or forged into apikes; framed guard bars; barred iron doors; ladders; framed baluster; walk ways; railings; framedwork or water tanks and similar work conforming to Fe 290 gde E 165 complete all as specified and directed.

M&L for coloured Non Skid Joint less ceramic tiles of size 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed .

All as per Sl item No 36 above but as in skirting over rendering 10mm thick in cement mortar 1:4.complete all as specified and directed.

M&L for 20-25mm thick machine cut kota stone slab flooring over and including 20mm thick cement screed in cement mortar 1:6 laid and jointed with grey cement slury mixed with pigment to match the shad of slab including grinding and polishing complete all as specified and directed.

All as per Sl item No 39 above but as in skirting /dado including 10 mm thick rendering in CM 1:4 complete all as specified and direcetd.

M&L for 25mm thick cement concrete type B-0, 1:2:4 (12.5 mm graded aggregate) as in sub floors finished fair and even to receive tiles/Kota stone flooring complete all as specified and directed.

Taking down carefully aluminium point wiring (light, fan, socket or power, bell complete fitting such as sockets, ceiling roses, pendants, batten holders, regulators and making good the disturbed surfaces of wall, floors, ceiling in CM 1:3 etc complete all as specified and directed by Engineer - in - Charge.

M & L for concealed conduit point wiring complete for light/ fan on independent /combine board with cable 1.5 sqmm (Nominal area) FRLS PVC insulated multistranded unsheathed copper conductor, drawn in and including PVC Concealed conduit pipe medium grade 20 mm dia, pipe hooks , elbows, juction covers and junction boxes , after cutting in wall chasing for conduits and sinking's for sunken cast iron/ pressed steel terminal boxes suitable length and thickness for mounting, switches, sockets,fan regulator with 3 mm thick plastic laminated sheet cover fixed with brass screwed and cup washers, duly grouting and painted with red oxide metal primer and making the good disturbed surfaces of wall in CM 1:3 with white wash or existing colour including provision of continuous earth continuity conductor along with point wiring of 1.5 sqmm copper PVC insulated cable for one light/ fan point controlled by one switch and connected to common earth dolly, complete all as specified and direced by the Engineer in charge.

All as per Sl item No 42 here in before but for one switch socket combination 5/6 Amp on independent board

All as per Sl item No 42 here in before but for one three pin socket outlet 5 Amp on same board

All as per Sl item No. 42 here in before but for one switch socket combinationt 6 pin 5/ 15 Amps on independent board with copper conductor 2.5 Sqmm

S & F switch piano flush type 5/6 Amps single pole one way complete all as specified and directed by Engir-in-charge

S & F switch socket combination 5 pin, type 5/6 Amps flush type complete all as specified and directed by Engir-in-charge

S & F switch socket combination 6 Pin, 5/16 Amps flush type complete all as specified and directed by Engir-in-charge

S & F Socket outlet 5 pin 5 Amps flush type complete all as specified and directed by Engir-in-charge.

S & F ceiling rose surface bakelite three terminals complete all as specified and directed by Engir-in-charge

S & F in replacment of existing light fitting with batton integrated LED channel 20 watt (integral sleek extruded polycarbonate body LED with white acrylic cover ) tube light fitting wall mounted complete with rod,driver and all other accessories including connection with flexible cable copper conductor twin core of size 23/.2 mm upto ceiling rose/connector complete all as specified and directed by Engir-in-charge

S & F LED light fitting mirror type with high output diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp includingconnecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engir-in-charge.

S&F flameproof cum waterproof LED Bulk Head Light fitting of 10W , IP 66 Protection of cast Aluminium alloy material and Heat and impact resistance toughen "A"clear glass having Anti corrosive epoxy powder coated finish complete with all accessories pre wired and including connecting up with three core flexible copper conductor cable with suitable size complete all as specified and directed by Engir-in-charge

S&F stepped type, single socket fan regulator not less than 400 watt for ceiling fan 1200/1400mm sweep complete all as specified and directed by Engir-in-charge

Taking down ceiling fan from hock and deposited at MES store yard.

Hanging only Ceiling fan after completion of repair work in said Bldg and connecting up including provision of cable from ceiling rose or connector of fan complete all as specified and directed by Engir-in-charge

S & F in replacement of sub-main wiring with two single core cables PVC insulated and un-sheathed 6 sqmm (Nominal Area) FRLS stranded copper conductor drawn in concealed PVC conduict dia 20mm “medium quality” conduit including 6.00 Sq mm (Nominal Area) copper cable as earth continuity conductor after chasing in wall and making good the disturbed surfaces and white wash or existing colour , necessary junction box and covers including necessary connections, PVC flexible pipes are used in pannel board while connecting the cable complete all as specified and directed by Engir-in-charge

S & F in repairs sheet metal enclosure for double door DB made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted SP & N 8 ways, 240 Volts, ISI marked, 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed by Engineer - in - Charge.

S & F in repairs sheet metal enclosure for double door DB made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted SP & N 2 ways, 240 Volts, ISI marked, 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed by Engineer - in - Charge.

S&F MCCB TP 100 Amps and 415 volts AC Supply ISI marked complete all as specified and directed by Engir-in-charge

S & F 240 V , 10 KA MCB ‘B’ curve Miniature Circuit breaker (MCB) single pole and current carrying capacity 6 to 32 Amp, in the MCB DB Complete testing and commissioning complete all as specified and directed by Engir-in-charge

S & F 240 V , 10 KA MCB ‘B’ curve Miniature Circuit breaker (MCB) SPN 32 AMP and in the MCB DB Complete testing and commissioning complete all as specified and directed by Engir-in-charge

Earthing complete with GI earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 Mtr deep below ground level ) with top edge of plate not less than 1.5 Mtr below ground level earth lead 4 mm dia along with GI pipe 20mm dia from plate to pannel board by means of bolts , nuts, check nuts and washers of GI all as shown electrical plate No -5 including alternate layer of charcoal dust and salt around the electrode and excavation , earth work, watering arrangement , funnel and wiremesh , 20mm GI pipe used for watering with iron funnel etc. all as specified and directed by Engir-in-charge

Supply and fixing LED building security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection including fixing arrangement with suitable galvanized iron pipe 35 mm bore “light grade” brackets 2 mtr length bent to shape to obtained required shape including clamps, nuts / bots / washers etc connecting with suitable flexible copper wire of size 23/0.0076 complete all as specified and directed by Engir-in-charge

S & F in repairs sheet metal enclosure for double door DBs made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted VTP & N 8 ways, 240 Volts, ISI marked 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation MCCB 100 Amp and isolators etc complete all as specified and directed by Engineer - in - Charge. (Make - Havells / Standard / Indo Asian)

Excavation in trenches not exceeding 1.5 mtr wide and not ecxceeding 1.5 mtr depth for laying of cables including taking up or down the LT cable in soft/loose soil complete all as directed

Returning filling in including spreading levelling watering and well ramming in layers not exceeding 25cm complete all as directed

Removal of excavated material (Soil) not exceeding 50 mtr and depositing where directed by Engr-in-Charge.

Material & labour for sand cushioning in trenches and well ramming in layers with 8 cm below and 15 cm above the cable with fine dry sand for cable protection and complete all as directed and specified

M&L for brick protection with sub class "B" bricks (old size) laid dry, flat in trenches over cable with longest dimension perpendicular to the axis of the cable complete all as specified and directed specified .

Supply and lay jointing and testing and commissioning in replacement of 35 Sqmmx4 core XLPE insulated, screened , PVC bedded galvanised steel strip or wire armoured electric power cable heavy duty multi stranded aluminium conductor & PVC sheathed LT cable 1100 V grade conforming to IS-7098 laid in trenches/ducts/fixed on poles wall/laid under roads/paths/drain/culverts or passing through pipes complete all as specified and directed by engineer in charge.

M&L for preparing new plastered surfaces of walls and applying three coat of white wash complete all as specified and directed.