SPL REPAIR REPLACEMENT OF LT OH LINE WITH UG CABLE FPB AND ALLIED WORKS AT DAUDPUR LINE UNDER GE DANAPUR CANTT

Amount

Dismantling of OH ACSR conductor of any size and removing unserviceable conductor from site complete all as specified & as directed.

Dismantling of LT insulators any type or size complete all as specified & as directed.

Dismantling of cross arms of MS channels or angle, section etc complete and setting aside for reuse complete all as specified & as directed.

M & L for Cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate in foundations, filling and mass concrete complete.

Excavation in trenches, in any type of soil not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc or not exceeding 10 Sqm on plan and not exceeding 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in any type of soil etc complete all as specified and directed.

Removing excavated soil not exceeding 50 m and depositing where directed at a level not exceeding 1.5m above the starting point ,complete all as specified and directed.

Returning, filling in excavated approved soil, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm each layer ,complete all as specified and directed.

M & L for dry sand cushioning to underground cables with 8cm thick before laying of cables and 15cm thick after laying and stretching of cable and gentally hand ramming and consolidation etc. complete all as specified and directed. Note :- Thickness of sand shall be measured 18 cm thick after punning.

M & L for Old size sub class ‘B’ bricks, laid in trenches as cable covers complete all as specified and directed.

Supply and fixing of GI tubing, light grade, 80 mm bore with all fitting laid in trenches / pole / wall for protection of cables in repairs complete all as specified and directed.

Supply and fixing of GI tubing, light grade, 40 mm bore with all fitting laid in trenches / pole / wall for protection of cables in repairs complete all as specified and directed.

M & L for horizontal boring mechanically across the existing road without disturbing the road surface for inserting 80/40 mm bore GI pipe complete all as specified and as directed by EIC. ( Note :- GI pipe will be measured and paid respective item of BOQ).

Taking out of pressed precast concrete interlocking paver block any shape and size and refixing of same with 50mm thick sand cushioning filling under floors or in foundations including watering and consolidation complete all as specified and directed by EIC.

S&F Cable route indicator / Marker made up of PCC Block in cement mortar 1:3:6 type C-1(20 mm graded stone aggregrate) of size 900mm x 300mm x 100 mm thick with "DANGER / LT 433 V CABLE / MES" embossing on cable route Indicator / Marker including painting as per approved colour and buried in ground 45 Cms including necessary earth work (as required / ordered at site) complete all as specified and as directed.

Supply and laying cable XLPE insulated screened, PVC bedded, galvanised, steel strip or wire armoured, electric power cable, (heavy duty) 1100 volts grade, with stranded aluminium conductor of size 185 Sqmm 3.5 core. (Make: Plaza/Finolex/ Polycab/Havells/Gloster).

All as per ser item No 15 above but of cross sectional area 150 sqmm 3.5 core

All as per ser item No 15 above but of cross sectional area 95 sqmm 3.5 core

All as per ser item No 15 above but of cross sectional area 16 sqmm 4 core

All as per ser item No 15 above but of cross sectional area 10 sqmm 4 core

All as per ser item No 15 above but of cross sectional area 10 sqmm 2 core

Supply and fixing pole mounted SMC junction box/bus bar chamber for loop IN/OUT connection of street light cable of size 295x195x100 mm high heat distoration temperature, non-fusing , shock proof, rustproof, 100 % weatherproof, fire retardant- class FV-O as per IS 11731 Part-II and suitable locking arragement with three phase and neutral aluminium busbar of size 20X3 mm of length 170 mm wrapped with PVC sleeves with maintained the colour code and provision of making holes with GI nuts, bolts & washers for cable connections mounted on hydrograpic insulators with nuts & bolts at both ends of busbar complete all as specified and directed. Make: Sintex /Hensel/Rittel.

Supply and fixing PVC Sheathed multi stranded unarmoured copper conductor cable LT 1100 volt grade Conforming to IS 7098 FRLS (inner sheet) of size 1.5 Sqmm 3 Core (Nominal Area) from pole junction box to light fitting with suitable size copper cable lugs and connector complete all as specified and directed. make Polycab/Havells

M & L for Cross arms, bracing, supports, clamps and back plate, fabricated from structural steel section including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as directed including two coats of synthetic enamel paint over a coat of red oxide primer, complete all as directed .

Supply, fabrication, installation and testing of LT factory made (CPRI approved) water and vermin proof protection pedestal type feeder pillar box of minimum size 1200mm x 600mm x 500mm (overalls), outdoor type made out of 3.00 mm thick CRCA sheet with frame and legs of mild steel angle iron of size 40 x 40 x 6 mm in all side with double door, front and back side openable and air ventilation arrangement including provision of cable looping box of size 600mm x 450mm x 400mm made out of 3 mm thick CRCA sheet with front side openable double door shutter hinged door and locking arrangement at back side complete painted with Powder Coated paint of approved shade and suitable for 3 phase 4 wire system 500 voltage grade complete wiring and all incoming connections with copper strip busbar of required size to MCCB input including PCC (1:3:6) type C-2 as in foundation of size 0.80m x 0.60m x 0.90m depth (30 cm below ground level & 60 cm above ground level) including necessary excavation and earth work complete all as specified and as directed alongwith comprising of the following accessories :- NOTE: Rate of earthwork and PCC are deemed to be inclusive in this item.

Supply ,fabrication, installation and testing of LT out door type factory made CPRI Approved , junction box of size 900mmX600mmX400mm (over all dimension) made out of 3.00 mm thick CRCA sheet dully supported with mild steel angle iron of size 25X25X5mm vertical frame and legs with mild steel flat iron 25X5 mm in horizontal sides of the frame with front and back side openable ,single hinged door / shutter with locking arrengement and powder coated finish both internal and external steel surfaces after necessary preparation of steel surfaces including providing PCC (1:3:6) type C2 foundation of size 0.80m X 0.6m X 0.90m depth (0.30m below ground level and 0.60m above ground level ) and connections of all outgoing / incomming existing cable of any size drawing / digging out cable from loops in trenches inclusive of necessary excavation and earthwork as required and relaying the cables including the following fitment accessories all complete as specified and as directed. (a) Alluminium bus bar of size 50 mm X 6 mm X 400mm long wrapped with PVC sleeves with maintained the colour code and provision of making holes as required with nuts, bolts & washers for cable connections including hydrograpic insulators with nuts & bolts at both ends = 04 nos. (b) Enamelled iron danger notice plate of 1.60 mm thick mild steel sheet of size 200 mm X 150mm , white with letters , figures and conventional skull and bones in signal red and fixed with nuts and bolts on door / shutter of JB for LT -01 No.

Supply, fixing and jointing of heat shrink LT cable end jointing kit suitable for 1100 volts grade 185 to 150 sqmm 3.5 core cable complete all as specified and as directed

Supply, fixing and jointing of heat shrink LT cable end jointing kit suitable for 1100 volts grade 95 sqmm sqmm 3.5 core cable complete all as specified and as directed

Supply, fixing and jointing of heat shrink LT cable straight through jointing kit suitable for 1100 volts grade 16 to 10 sqmm 4 core cable complete all as specified and as directed

M & L for Earthing to panels or junction boxes with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick, buried directly in ground (earth pit not less than 2.25m below normal ground level) with top edge of earth plate not less than 1.5m below normal ground level connected to main earth GI strip of size 32 X 6 mm by means of bolts, nut, check nuts and washers of galvanized iron or steel all as shown in electrical plate No.05 of MES Schedule pt-I 2009, GI earth wire protected by GI pipe 15mm dia light grade and connected to earth test point including excavation in any type of soil,returning filling, disposal of soil, providing charcoal dust and common salt upto top edge of earth plate, construction of PCC pit with RCC cover, funnel, watering pipe of 20mm dia GI light grade and provision of earth test point including testing on completion complete Note : Main earth lead beyond 7.5 meter shall measured and paid saperatly.

M/s Naresh Chand Agrawal

ANAHITAS INFOSOLUTIONS PRIVATE LIMITED

M/S SHATRUGHAN SINGH CHAUHAN

VAISHNAVI CONSTRUCTION

jaglalchoudharyandsons

M/S SAROJ KUMAR SINGH

HARINANDAN RAI SONS

SINHA CONSTRUCTION