PROVN OF GUARD ROOM WITH TOILET BLOCK FOR SECURITY TOWER NO 11 AT_H_ZONE_PROVN OF MULTIPURPOSE PARKING SHED INFRONT OF 12_I_RO FLT AND SPECIAL REPAIRS TO BLDG NO T_13 AND T_13 BC OF 165 MH AT RMS UNDER AGE BR_II OF GE 868 EWS

Amount

M&L for surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in soft/ loose soil complete all as specified and directed by Engr-in-Charge

M&L for excavation in trenches n.exc 1.5m wide and n.exc 1.5m in deepth; for foundation etc or for shafts, wells, cesspits, manhole, pier holes, etc n.exc 10 Sqm on plan and n.exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed by Engr-in-Charge

M&L for PCC 1:4:8 type D-2 (using 40mm graded agg) as in foundation, filling and mass concrete complete all as specified and directed by Engr-in-Charge

M&L for mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in-Charge

All same as per item No 4 above but 6mm to 8mm dia complete all as specified and directed by Engr-in-Charge

All same as per item No 4 above but 5mm dia and over and including 10mm dia in stirrups spacers and binders complete all as specified and directed by Engr-in-Charge

M&L for RCC (Nominal Mix) type B1 1:2:4 (20 mm graded aggregate) as in foundation, including rafts, footings, foundation beams; plinth beams; bases for coloumns, etc basement slabs under reamed piles and mass concrete complete all as specified and directed by Engr-in-Charge

M&L for RCC (Nominal Mix) type B1 1:2:4 (20 mm graded aggregate) as in columns, pillars, piers, posts and struts complete all as specified and directed by Engr-in-Charge

M&L for RCC (Nominal Mix) type B1 1:2:4 (20 mm graded aggregate) supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engr-in-Charge

M&L for RCC (Nominal Mix) type B1 1:2:4 (20 mm graded aggregate) as in chajjas complete all as specified and directed by Engr-in-Charge

M&L for RCC (Nominal Mix) type B1 1:2:4 (20 mm graded aggregate) as in beams, cantilvers, bressummers, lintels over 1.5m span complete all as specified and directed by Engr-in-Charge

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed by Engr-in-Charge

Use and waste of formwork to sides of pillars posts, struts, piers, columns and stanchions finished the suface rough complete all as specified and directed by Engr-in-Charge

Use and waste of formwork to sides and soffits of floors or roof beams, beams haunchings, girders,bressummers lintels, cantilevers, shelves including supports overhangs etc also splays between floors and beams etc complete all as specified and directed by Engr-in-Charge

Use and waste of formwork to chajjas, troughts and similar items including edges complete all as specified and directed by Engr-in-Charge

M&L form work with fair finished to soffits of suspended slabs such as roof slabs, floor slabs, landing and similar work nexc 200mm thick (horizontal or sloping) complete all as specified and directed by Engr-in-Charge

Supply only water proofing compound complete all as specified and directed by Engr-in-Charge

M&L for brick work with sub class `B' bricks straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed by Engr-in-Charge

M&L for brick work with sub class `B' bricks straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed by Engr-in-Charge

S & F 125 x 60mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and directed by Engr-in-Charge

S&F steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay, complete with glazing bars, devetailed or welded complete all as specified and directed by Engr-in-Charge

S&F steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay, complete without glazing bars, devetailed or welded complete all as specified and directed by Engr-in-Charge

S&F ventilator with top hung shutter including hinges, steel peg stay complete all as specified and directed by Engr-in-Charge

M&L 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed by Engr-in-Charge

S&F 35m thick factory made glazed and skeleton shutter open rebated and prepared to receive glass gauge etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitered beads or clearing glass etc, size of members of shutters as specified in SSR part I section 8 clause 8.20 (a) of IInd class hard wood complete all as specified and directed by Engr-in-Charge

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S square tube, suppling and fixing in opening as per specification and drawing complete all as specified and directed by Engr-in-Charge

S&F factory made solid panel PVC door shutter 30mm thick (style).consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with eat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement suppling & fixing in the frame at site as per specification and drawing complete all as specified and directed by Engr-in-Charge

S&F 3mm thick figured glass, pin head type and glazing with oil putty in squares n.exc 0.5 Sq.m in each pane complete all as specified and directed by Engr-in-Charge

S&F mild steel framed work such as grills, gratings etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed by Engr-in-Charge

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm complete all as specified and directed by Engr-in-Charge

S&F 300mm door spring ordianary rat taill rod pattern springs including roller and roller plate complete all as specified and directed by Engr-in-Charge

S&F 150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed by Engr-in-Charge

S&F 150mm extruded aluminium alloy handles fabricated type anodised complete all as specified and directed by Engr-in-Charge

S&F 100mm medium weight butt hinges cold rolled mild steel complete all as specified and directed by Engr-in-Charge

S&F 200mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed by Engr-in-Charge

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and siding bolts of extruded sections or cast aluminium alloy complete all as specified and directed by Engr-in-Charge

M&L for hardcore of gauge n.exc 63mm, deposited, spread and levelled in layers n.exc 15cm thick, watered and rammmed to a true surface complete all as specified and directed by Engr-in-Charge

M&L for PCC 1:5:10 type E-2 (using 40mm graded agg) as in foundation, filling and mass concrete complete all as specified and directed by Engr-in-Charge

M&L 40 mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded stone agg) as damp proof course to horizontal or vertical surfaces including necessary form works, applying evenly a coat of blown type bitumen at 1.50 kg per sqm and blinding with clean dry sand @ 0.05 cum per sqm including 150 micron thick polythene film laid on a coat of bitumen primer @ 0.30 to 0.50 kg per sqm complete all as specified and directed by Engr-in-Charge

M&L PCC 1:4:8 type D-2 75mm thick as in sub base of floor complete all as specified and directed by Engr-in-Charge

M&L for non skid coloured joint free tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exc 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed 15mm thick in CM 1:6 complete all as specified and directed by Engr-in-Charge

Same as per ser No 41 but on vertical surfaces such as skirting , dado risers to steps over and including 10 mm thick bedding layer in CM 1:4 , set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by Engr-in-Charge

S&F non-skid coloured ceremic tiles 7 to 8 mm thick (Square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floors etc set and jointed in neat cement slurry and pointed in neat cement slurry and pointed in white or coloured cement to match the existing surfaces including 15mm thick screed bed or bedding layer in cement mortar 1:6 for fixing of tiles complete all as specified and directed by Engr-in-Charge

M/L glazed ceremic tiles 200x300x7 mm in dado set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles including 10mm thick cement mortar 1:4 for fixing of tile complete all as specified and directed by Engr-in-Charge

M&L for 75mm thick PCC in 1:3:6 type C1 (using 20mm graded agg ) as in plinth protection/path finished the surface even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge

M&L for rendering 15mm thick plaster in CM 1:6 on fair faces of brick or concrete work finished the surface even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge

M & L rendering 15mm thick on cement mortar 1:4 mixed with water proofing compound @ 3% of qty of cement finished of brick or concrete work finished the surface even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge. Note : WPC will be measured and paid separately.

M&L for rendering 5mm thick plaster in CM 1:3 on fair faces of brick or concrete work finished even and smooth without using extra cement as in ceiling complete all as specified and directed by Engr-in-Charge

M&L for preparation of new plastered surfaces and applying two coats of oil bound distemper of approved shade/tint over a coat of primer on walls complete all as specified and directed by Engr-in-Charge

M&L for preparation of new wall surface and two coats of cement base paint on walls complete all as specified and directed by Engr-in-Charge

S&F 15mm dia bore tube medium grade galvanised with all fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed by Engr-in-Charge

S&F 20mm dia bore tube medium grade galvanised with all fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed by Engr-in-Charge

S&F 15mm bore dia bib taps cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed by Engr-in-Charge

S&F 15mm dia bore Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed dwon high pressure, with or wothout lettered `Hot' or `Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed by Engr-in-Charge

S&F CP angle cock 15mm cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed by Engr-in-Charge

S&F 1000 ltr capacity ratational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as per specified in SSR Part I complete all as specified and directed by Engr-in-Charge

S&F Vitreous China wash basin white flat back size 550x400mm excluding taps chain and plug and procelain stopper but including brackets including PVC waste pipe 32 mm complete all as specified and directed by Engr-in-Charge

S&F Gun metal globe or gate valves, with iron wheel head, screwed both ends for iorn pipe and fixed in 20mm dia bore pipe complete all as specified and directed by Engr-in-Charge

S&F Vitreous China squatting pan, `Orissa' pattern size 580 x 440mm white with integral foot rests (excluding flushing cistern and flush pipe) including provision of lime concrete bedding complete all as specified and directed by Engr-in-Charge

S&F vitreous china half stall urinal flat back, size of 465 x 355 x 265mm (minimum) white, with grating and union for discharge pipe including waste pipe of polythelene of low or high density or PVC 32mm dia complete all as specified and directed by Engr-in-Charge

S&F ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed in 20mm dia bore pipe complete all as specified and directed by Engr-in-Charge

Supply pnly 32 mm waste coupling of PTMT (half or full threaded) complete all as specified and directed by Engr-in-Charge

S&F Grating doom 100mm dia of PTMT (min wt -25gms) complete all as specified and directed by Engr-in-Charge

S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed by Engr-in-Charge

S& F flush pipe of polyethylene of low or high density of PVC 32mm dia for low level cistern complete all as specified and directed by Engr-in-Charge

S&F PVC 10 ltrs valveless syphonic action type flushing cistern low level, white, with inlet ball valve float and handle including brackets complete all as specified and directed by Engr-in-Charge

S&F towel rail 450mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (min wt - 170 gms) complete all as specified and directed by Engr-in-Charge

S&F 100mm cast iron sanitary connections socket to fit WC out let complete all as specified and directed by Engr-in-Charge

M&L for preparation of new wooden of wood based surface of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engr-in-Charge

M&L for preparation of new steel surface of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a red oxide primer complete all as specified and directed by Engr-in-Charge

S&F 15 mm dia concealed stop valve fancy type CP with long shank and cup complete all as specified and directed by Engr-in-Charge

S&F 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall/floor complete all as specified and directed by Engr-in-Charge

S&F 75 mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall/floor complete all as specified and directed by Engr-in-Charge

S&F of 110mm dia PVC (SWR) bends complete all as specified and directed by Engr-in-Charge

S&F 75mm PVC(SWR) bends any radius with adess door complete all as specified and directed by Engr-in-Charge

S&F of 75dia PVC (SWR) Vent cowl complete all as specified and directed by Engr-in-Charge

S & F 75mm dia, PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed by Engr-in-Charge

S&F bands , straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stays) , heavy , for large gates, hooks and pintle hinges, large hasp and staples, chains, hand made sliding bolts, clamps, hold fasts , wall ties, hooks for hanging fans, plain angles cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps , palte washers and similar small articles conforming to Fe 290 , Gde E- 165 complete all as specified and directed by Engr-in-Charge

S & F Pre-painted galvatume aluminum zinc coating GI vased corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed by Engr-in-Charge

S & F Pre-painted galvatume aluminum zinc coating GI vased Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed by Engr-in-Charge

S & F for 4 mm thick of size 600x600mm HSPC (high pressure Steam Cured) pre-Painted self embossed, textured designer board E-Board Classic to be fixed GI powder coated grid/section size 600mmx600mm with main runner 38x24x0.9mm thick ,cross tee 28.6x24x0.9 mm and wall angle 19x19x0.9 mm duly suspended with 4mm dia GI bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip including providing provisions for light fixtures of any size etc complete all as specified and directed by Engr-in-Charge

S&F 150mm dia mild steel sheet eaves gutters of 1mm thick sheet, galvanised class 3, half round with rounded edges complete all as specified and directed by Engr-in-Charge

S & F of steel work as in tubular trusses including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS – 1161 – 1979 grade St – 240 complete all as specified and directed by Engr-in-Charge

S&F mild steel screw bolts 11 to 15 mm dia (machine made) with hexagonal or square heads at one end and screwed the other or screwed both ends each screwed end to be fitted with washers and one hexagonal or square nut nexc 5 cm long complete all as specified and directed by Engr-in-Charge

S&F Plates (plain or chequered) channels. Square cut or notched ) (ordinary and counter sunk) forming holes, without any attachment of Fe-410-W (Gde-E-250 quality-A) complete all as specified and directed by Engr-in-Charge

S&F bands, straps or stays , plain angle cleat or flat iron cleat or securing purlins to wood trusses or rafters, knee piece and similar small articles etc conforming to Fe-290 Gde E-165 complete all as specified and directed by Engr-in-Charge.

S&F Draperly rod /Harrison rails of stainless steel of 20mm dia with fixing brackets , stops, rollers and rings etc complete all as specified and directed by Engr-in-Charge

S&F Brass chromium plated shower rose 125mm size complete all as specified and directed by Engr-in-Charge

M&L Cement concrete 1:3:6 type C-1 (20 mm graded agg ) in surface channels and drains complete all as specified and directed by Engr-in-Charge

Extra for forming fair finished drain or channel 30cm inner grith in cement concrete, using extra cement, including forms, moulds, mitred/stop ends etc complete all as specified and directed by Engr-in-Charge

Removing excavation material n exc. 50m & deposited where directed at a level n exc. 1.5m above the starting point complete all as specified and directed by Engr-in-Charge

Returning, filling in, including spreading, leveling, watering & well ramming in layer s not exc 25 cm complete all as specified and directed by Engr-in-Charge

M&L of earth filling under floor well ramming including watering as required Spreading & leveling in layers n.exc. 25cm thick complete all as specified and directed by Engr-in-Charge

S&F for depth 0.70m – 1.65 m, DWCPE (SN8) 180 (OD)/163(ID) mm diameter Pipes laid on 150 mm thick PCC 1:3:6 type C-2 including packing under and haunching against the sides of pipes bed with excavation in any type of soil, including manholes/drop manhole of standard size made of Brick masonry/ RCC/Precast RCC with SFRC ventilating cover and frame. Includes all items and activities to execute and make sewer line functional complete all as specified and directed by Engr-in-Charge

Providing pre cast cement concrete type B- 1, 1;2:4 (20mm graded aggregate) in cover slabs (for man holes etc) and similar articles with plain faces set in cement mortar 1:4 complete all as specified and directed by Engr-in-Charge

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft and loose soil complete all as specified and directed by Engr-in-Charge

Excavation in post holes (or similar holes) each n. exc 0.50 m and getting out ,in soft/disintegrated rock complete all as specified and directed by Engr-in-Charge

M&L for plain cement concrete 1:5:10 type E-2 (using 40mm graded stone aggregate) as in foundation, filling & mass concrete, sub base complete all as specified and directed by Engr-in-Charge

M&L preparing new plaster surfaces of wall and applying three coats of white wash on walls complete all as specified and directed by Engr-in-Charge

M&L for preparation of new steel surfaces of any description, n exc 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer complete all as specified and directed by Engr-in-Charge

Removing excavated soil & material n exc, 50m and deposition where directed at a level n exc. 1.5m above the starting point complete all as specified and directed by Engr-in-Charge

M&L Machine pressed precast concrete interlocking paver block any shape and size confering to IS 15658-2006 of 60 mm thickness M-35 grade fixed with grey cement and no pigment complete all as specified and directed by Engr-in-Charge

M&L sand cusion for interlocking tiles complete all as specified and directed by Engr-in-Charge

M&L for PCC 1:2:4 type B1 (using 20mm graded aggregate) in copings, kerbs, channels, water through and the like including weathering, slightly rounded or chamfered angles and throating as directed chamfered necessary for work complete all as specified and directed by Engr-in-Charge

Dismantling asbestos cement sheet (Corrugated, semi corrugated etc ) in roof covering complete all as specified and directed by Engr-in-Charge

Dismantling wall and ceiling boards (fibre pulp insulation etc) or insulation boards, slabs, blankets any thickness, incl cover fillets complete all as specified and directed by Engr-in-Charge

Dismantling timber scantlings 40 sqcm and over in section unframed work complete all as specified and directed by Engr-in-Charge

Dismantling boarding any description fixed in any position with nails complete all as specified and directed by Engr-in-Charge

Dismantling mild steel or wrought iron work of any description not otherwise provided for complete all as specified and directed by Engr-in-Charge

S & F Pre-painted galvatume aluminum zinc coating GI vased Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed by Engr-in-Charge

S/F 2nd class hard wood scantling as in purlins rafters ,& framed work etc clean sawn complete all as specified and directed by Engr-in-Charge

S&F Rolled sections as in roof truss, purlins including cleats GDE Fe 410-0-or Fe 310-0 complete all as specified and directed by Engr-in-Charge

S&F mild steel bolts purpase made with hexagonal or square head one end and screw the other or screwed both ends each screw end to be fitted with washers and one hexagonal or square nut length of bolt exc 5cm but n.exc 10cm complete all as specified and directed by Engr-in-Charge

M&L 25mm thick second class hard wood boarding , plained one side with butt joints as in eaves boards complete all as specified and directed by Engr-in-Charge

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness below or above ground level complete all as specified and directed by Engr-in-Charge

Dismantaling floor,hearth or wall tiling including cement mortar bedding (but not backing),removing serviceable tiles to store and rubbbish off the premises complete all as specified and directed by Engr-in-Charge

M&L 40 mm thick PCC (1:2:4) type B-1 using 20 mm graded stone aggregate as in floor complete all as specified and directed by Engr-in-Charge

M&L 25mm thick Cement concrete type B-0, 1:2:4 (12.5mm graded aggregate) finished even and smooth without using extra cement. complete all as specified and directed by Engr-in-Charge

M&L Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc complete all as specified and directed by Engr-in-Charge

M&L for Brushing neat cement slurry with 3.0 Kg of cement per Sq meter complete all as specified and directed by Engr-in-Charge

Demolition of unreinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engr-in-Charge

M&L for PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in cills, copings, benching on chajjas, roof kerbs, bed blocks and the like including weathering, slightly rounded or chamfered angles and throating as directed with and including necessary form work complete all as specified and directed by Engr-in-Charge

Taking down chowkhat or frame not exc 1.5 sqm each (with out taking off shutters from the frame) complete all as specified and directed by Engr-in-Charge

Taking down chowkhat or frame exc 1.5 sqm not exc 4 sqm each (without taking off shutters from the frame) complete all as specified and directed by Engr-in-Charge

Taking down shutters of any description exc 1 Sqm and not exc. 2 Sqm each complete all as specified and directed by Engr-in-Charge

Taking down shutters of any description n.exc 1 Sqm each complete all as specified and directed by Engr-in-Charge

M&L 2nd class hard wood plain solid straight chowkats and frames wrought framed rebated on the solid rounded or chamfered put together with glue pined joints complete all as specified and directed by Engr-in-Charge

M&L 35 mm thick 2nd class HW plain framed pannelled shutter (any number of panels) with panels of timber flat on both sides or of veneered particle board medium density , wood particle board with commercial face veneers , supplied and fitted to chowkats complete all as specified and directed by Engr-in-Charge

M/L 30mm thick 2nd class hard wood Glazed and skelton shutter, open rebated and prepared to receive glass, gauge etc. devided into squares with plain chamfered or rounded, mitred and rebated sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.24(b) complete all as specified and directed by Engr-in-Charge

M/L 30mm thick 2nd class hard wood Glazed and skelton shutter, open rebated and prepared to receive glass, gauge etc. devided into squares with plain chamfered or rounded, mitred and rebated without sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.24(b) complete all as specified and directed by Engr-in-Charge

S&F 12mm thick Veneered decorateive plywood, grade 1 (with BWR resin) with decorate face veneers on one faces; fixed with screws to timber frame work as wall panel complete all as specified and directed by Engr-in-Charge

S & F 18/19 mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work, for cup board including lipping / beading as required complete all as specified and directed by Engr-in-Charge

S&F in repairs aluminium (die cast) body door closer hydrulically regulated, designation No 2, universal type suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 Kg and fixed complete all as specified and directed by Engr-in-Charge

S&F Powder coated of any colour (Thickness or powder coating not less than 50 micron) Anodised aluminium frame for doors, windows ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed by Engr-in-Charge

Supply and fixing 3 mm thick frosted glass, ordinary quality and glazing with oil putty in square n.exe 0.50 Sqm in each pane complete all as specified and directed by Engr-in-Charge

M&L butt hinges, medium weight 75 mm long size complete all as specified and directed by Engr-in-Charge

S&F Aluminium handle cast type anodised 150 mm long complete all as specified and directed by Engr-in-Charge

S&F 125mm size aluminium handles,cast type,anodised all as directed complete all as specified and directed by Engr-in-Charge

S&F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, overall length of cover plate 140mm complete all as specified and directed by Engr-in-Charge

M & L sheet glass ordinary quality 3mm thick and glazing with oil putty in squares n.exc. .5 sqm each pane complete all as specified and directed by Engr-in-Charge

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing fixing new ones complete all as specified and directed by Engr-in-Charge

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed by Engr-in-Charge

S&F in repairs galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed by Engr-in-Charge

Taking down cement plaster on brick walls including raking out joints hacking for key, scrubbing down with water etc complete all as specified and directed by Engr-in-Charge

Demolition of reed lathing single or double inclduing batten and plaster or chicken wire lathing complete all as specified and directed by Engr-in-Charge

Demolition of brick work built in cement mortar incl all quions, arches pillars etc but excl ashalar facing complete all as specified and directed by Engr-in-Charge

Brickwork but except bricks with subclass `B' bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4 complete all as specified and directed by Engr-in-Charge

Brickwork but except bricks with sub class B bricks straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed by Engr-in-Charge

Supply only integral water proofing compound ( ISI marked ) complete all as specified and directed by Engr-in-Charge

M&L 18 mm thick plastering in CM 1:4 on one side of lathing in two separate layers even and smooth without using extra cement incl WPC complete all as specified and directed by Engr-in-Charge Note: (WPC shall be measured and paid separately)

M&L 12 mm thick plastering in CM 1:6 the other side of lathing finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge

M&L GI wire netting 0.71 mm dia and 12 mm mesh lathing in to reed in walls incl all laps cutting and waste complete all as specified and directed by Engr-in-Charge

Demolition of reinforced cement concrete in roofs, floors (other than ground floors), beams, chajjas, fascias, fins and similar works complete all as specified and directed by Engr-in-Charge

M&L for preparation of old painted surfaces of wood and wood based material of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engr-in-Charge

M&L for preparation of new untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engr-in-Charge

M&L for preparation of old painted steel and iron surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engr-in-Charge

M&L for preparation of old painted steel surfaces not exc. 10 cm width/girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engr-in-Charge

M&L for preparation of old decorated surfaces of walls by washing, rubbing down and stopping of distempered surfaces and applying one coat of oil bound distemper of approved shade/tint complete all as specified and directed by Engr-in-Charge

M&L for complete removal of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces and applying two coats of cement base paint of approved shade on walls complete all as specified and directed by Engr-in-Charge

M&L for preparation of old decorated surfaces of walls (plastered) by brooming down with steel wire brushing and applying one coat of white wash on wall complete all as specified and directed by Engr-in-Charge

Taking up or down steel tubing and connections including cleaning for refixing with all fittings for 15 mm bore GI tubing complete all as specified and directed by Engr-in-Charge

Taking up or down steel tubing and connections including cleaning for refixing with all fittings for 20 mm bore GI tubing complete all as specified and directed by Engr-in-Charge

Refixing of old steel tubing and connections in new or old position with all fittings to floor, wall or ceiling as directed, for 15mm bore GI tubing complete all as specified and directed by Engr-in-Charge

Refixing of old steel tubing and connections in new or old position with all fittings to floor, wall or ceiling as directed, for 20mm bore GI tubing complete all as specified and directed by Engr-in-Charge

M&L cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves lintels etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good cutting not exc 10cm girth complete all as specified and directed by Engr-in-Charge

S&F tubes medium grade, galvanised wih all fittings and fixed complete to walls and ceiling or laid on floors etc, 15 mm bore complete all as specified and directed by Engr-in-Charge

S&F tubes medium grade, galvanised wih all fittings and fixed complete to walls and ceiling or laid on floors etc, 20 mm bore complete all as specified and directed by Engr-in-Charge

M&L dismantling water tank of exc 500 ltr and not exc 1000 ltr Capacity complete all as specified and directed by Engr-in-Charge

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning the complete inner surface by rubber/nylon scraper to remove sludge/silt and washing with bleaching power solution and then clear water, etc. and hoisting in postion if required reconnecting and re-fixing in position exc 500 but n exc 1000 ltrs complete all as specified and directed by Engr-in-Charge

Taking down AC/Salt glazed ware pipes and fittings upto 110mm complete all as specified and directed by Engr-in-Charge

S&F in repair 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed by Engr-in-Charge

S&F in repairs vitreous china water closet Padestal pattern (white) excluding fixing bolts, flushing cistern and flush pipe and including EWC Sheet cover complete all as specified and directed by Engr-in-Charge

S&F in repairs for 15mm dia of pipe bib taps cast copper alloy, fancy type, chromium plated with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engr-in-Charge

S&F in repairs for 15mm dia of pipe stop valves,fancy type and chromium plated, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for Unions and fixed complete all as specified and directed by Engr-in-Charge

S&F grating doom 125mm dia with waste hole of PTMT (Min wt 40 gms) complete all as specified and directed by Engr-in-Charge

S&F in repairs 600mm long tubular tower rail brass chromium plated 20mm dia, D type 60cm longfixedwith two plugs (Gutties) of 2nd class hard woodembeded in cement mortor 1:3 with MS screws complete all as specified and directed by Engr-in-Charge

S& F in repairs PVC mounted 5mm thick bevelled edge looking mirror 550 x 400mm including taking down old fixed complete all as specified and directed by Engr-in-Charge

S&F PVC Shelves of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats. (Minimum weight 105 gms) complete all as specified and directed by Engr-in-Charge

M&L 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite & including 20 mm thick screed bed (bedding layer) in CM 1:4 complete all as specified and directed by Engr-in-Charge

M/L for 2 mm thick Birla white putty/JK white wall care putty on walls complete all as specified and directed by Engr-in-Charge

Writing letters or figures with synthetic enamel paint (Block, Roman, Italic or Indian) not exceeding 30cm high over old painted surfaces complete all as specified and directed by Engr-in-Charge

S&F Sheet glass assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 600 mm long complete all as specified and directed by Engr-in-Charge

M&L for anti-termite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed by Engr-in-Charge

M&L for anti-termite treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed by Engr-in-Charge

M&L for anti-termite treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and directed by Engr-in-Charge

Material and labour for precast Cement Concrete chequered tiles of size 200 x 200 x 25mm thick as in floor, set and jointed in neat cement slurry and pointed with cement laid over and including 20mm thick screed bed in CM (1:4) complete all as specified and directed by Engr-in-Charge

Material and labour for 20-25 mm thick machine cut kota stone slab over and including 20mm thick screed bed in cement mortar (1:4) with roughening of surface, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engr-in-Charge

Material and labour for 20-25 mm thick machine cut kota stone slab on verticle surface as skirting/dado over and including 10mm thick cement plaster in cement mortar (1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engr-in-Charge

M&L for Point wiring complete with 1.5 Sqmm single core PVC insulated cable, with multi strnded copper conductors FRLSH 1100 volt grade, drawn through and including PVC casing and caping with all conduit accessories and making good to the disturbed surfaces of walls, ceiling, floors etc. to match with the existing surface ) and including provision of 1.5 Sqmm FRLSH PVC insulated copper cable as earth continiuty conductor connected to common earth dolly complete with PVC switch board for fixing switch socket etc complete all as specified and directed by Engineer-in-Charge. Make: finolex/Havells/RR Kabel. Make of caping/casing & PVC boxes: Prestoplast/finolex/Supreme.

One light point controlled by one, one way switch .

One Ceiling fan point controlled by one, one way switch.

One 3 pin socket outlet 5 Amps on the same board with other switches.

One 3 pin socket outlet 5 Amps on the independent board.

All as per item No- 190.00 here-in-before but with 2.5 Sq mm for 3 pin 15 Amps socket point controlled by one switch on independent board and 2.5 Sq mm copper conductor green in colour as earth continuity conductor connected to common earth dolly complete all as specified and directed by Engineer-in-Charge.

M&L for Switch piano flush type single pole, one way 5A complete all as specified and directed by Engineer-in-Charge.

M&L for Socket outlet, 2 in 1, 5 pin 5A flush type complete all as specified and directed by Engineer-in-Charge.

M&L for stepped type electronic fan regulator 100 Watt socket size flush type on the existing phenolic laminated sheet etc complete all as specified and directed by Engineer-in-Charge.

M&L for ceiling rose 3 terminal PVC/Polycarbonate isolated body with PVC round/squareblock complete all as specified and directed by Engineer-in-Charge.

M&L for Lamp holder , PVC/ Polycarbonate type with PVC round/square block incl 9 watt LED lamp suitable for lamp holder fittings incl taking down old unsv light fitting complete all as specified and directed by Engineer-in-Charge.

M&L for 20W LED, 4', Wall mounted LED batten, extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver.etc with all accessories internally pre-wired and fixing the same on and including two Nos PVC blocks and connecting up with flexible copper cable of suitable size from ceiling rose to the light fitting incl taking down old unsv light fitting complete all as specified and directed by Engineer-in-Charge. Make : Havells Cat No LHFYBYPNIA1W022 Regal (batten) & LHDLEFXD5LR020(LED Tube) or equivalent in Bajaj/Philips

M&L for 10W LED, 2', Wall mounted polycarbonate batten internally pre-wired with electronic driver and polycarbonate diffuser and fixing the same on and including two Nos PVC blocks and connecting up with flexible copper cable of size 0.75 Sq mm 3 core from ceiling rose to the light fitting complete all as specified and directed by Engineer-in-Charge. Make: Havells Cat No LHEXBQP5IN1W009 or equivalent in Bajaj/Philips

M&L for LED 1x20W Security light fitting, drawn through including GI bracket of 25mm bore light grade bent to shape and fixed on wall with metal fastners 2 Nos 10mm dia incl drilling holes as required and connecting up with flexible copper cable of suitable size from ceiling rose to the light fitting complete all as specified and directed by Engineer-in-Charge. Make:-Havells Cat Pt No LHETBXU7PA6S020 or equivalent in Bajaj/Philips

Taking down LT UG cable/ service connection of any size and M&L for laying of LT UG cable, XLPE insulated, galvanised steel strip or wire armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area of 16 sq mm, 4 core complete all as specified and directed by Engineer-in-Charge. NOTE :- (i) Excavation and earth work, sand cushioning, cable protection cover, pipe etc. shall be measured and paid seperately under relevant items. Make : Havells/Finolex/Polycab/Richa

M&L for laying of LT UG cable, XLPE insulated, galvanised steel strip or wire armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area of 25 sq mm, 2 core complete all as specified and directed by Engineer-in-Charge. Note: (i) Excavation and earth work , dand cushioning , cable protection cover, pipe etc shall be measured seperately under relevent items.

M&L for MCB Distribution board double door type SPN 8 way, sheet steel, powder painted, with neutral link & earth bar etc. and fixing MCBs of various rating capacity including taking down old unsv MCB DBs complete all as specified and directed by Engineer-in-Charge. Make:- Legrand Cat No 507611 or equivalent in ABB/Siemens

M&L for MCB Distribution board double door type SPN 4 way, sheet steel, powder painted, with neutral link & earth bar etc. and fixing MCBs of various rating capacity including taking down old unsv MCB DBs complete all as specified and directed by Engineer-in-Charge. Make:- Legrand Cat No 507610 or equivalent in ABB/Siemens

M&L for MCB TPN 63 Amps, 415 volts, 50 Hz suitable for fixing in MCB DB 'C' series complete all as specified and directed by Engineer-in-Charge. Make:- Legrand Cat No 408702 or equivalent in ABB/Siemens

M&L for Isolator SPN 63 Amps 'C' series, 230 volts, 50 Hz suitable for fixing in MCB DB incl taking down old unsv MCB complete all as specified and directed by Engineer-in-Charge. Make: Legrand Cat No 408702 or equivalent in ABB/Siemens.

M&L for MCB SPN 40 Amps, 415 volts, 50 Hz suitable for fixing in MCB DB 'C' series complete all as specified and directed by Engineer-in-Charge. Make:- Legrand Cat No 408617 or equivalent in ABB/Siemens

M&L for MCB SP 5-32 Amps 'C' series, 230 volts, 50 Hz suitable for fixing in MCB DB incl taking down old unsv MCB complete all as specified and directed by Engineer-in-Charge.

M & L for Exhaust fan of 400 mm sweep metal body with metal louvers fixed with wall complete all as specified and directed by Engineer-in-Charge. ke: CG/Havells/Bajaj.

M & L for ceiling fan of 1200 mm sweep with 230 Volt, 50 Hz 'C' series complete all as specified and directed by Engineer-in-Charge. Make: CG/Havells/Bajaj.

Supply & laying tubes ' medium grade ' galvanised,GI tubing with all fittings, fixed complete to walls/laid in floors/ trenches/ road crossing of size 25 mm dia bore complete all as specified and directed by Engineer-in-Charge ke:- Jindal/TATA/Prakash surya

Supply & laying tubes ' light grade' galvanised, with all fittings, fixed complete to walls, poles, ceilings or laid in floors/ trenches/ road crossing for protection of cables of size 40 mm dia bore including taking down corroded GI tubing complete all as specified and directed by Engineer-in-Charge.

M&L for sub main wiring with two runs of 4 Sq mm and one run of 2.5 Sq mm for earth wire with multi standard copper conductors, 1100 volts grade, drawn through and including PVC double locked Casing & caping including complete all as specified and directed by Engineer-in-Charge. NOTE:- two runs of 4 Sq mm + one run of 2.5 Sq mm and one run of PVC casing & capping and its accessories of suitable size shall be measured as one unit length.

Taking down Ceiling fan/Exhaust fan of any sweep carefully from its installed position, dismantling complete, cleaning all dust, applying grease for bearing, painting of fans complete with superior quality synthetic enamel paint by spraying including filling cavaties with filler, after cleaning all dust, reassembling the fan and blades, hanging/ fixing the fan in its original position and testing on completion complete all as specified and directed by Engineer-in-Charge.

M&L for rubber bush with clamping set, comprising GI bolt, nut and split pin complete all as specified and directed by Engineer-in-Charge.

M&L for replacement of capacitor2.5 Mfd incl making electrical connection complete all as specified and directed by Engineer-in-Charge.

M&L for replacement of steel ball bearing/bush of suitable size compatible to the existing ceiling fan/Exhaust fan complete all as specified and directed by Engineer-in-Charge.

Dismantling and taking out burnt copper winding from ceiling fan of 1200mm sweep, any make, model, type and rewinding the same with new super enameled copper wire of similar gauge and number of turns as exist for full speed including cleaning and greasing of bearing/ bushes, taping varnishing, heating and replacement of defective parts and reassembling of fan after testing complete to the entire satisfaction of the Engr-In-Charge.

M& L for 25 Ltrs water storage electric Geyser 230 Volts AC incl fixing to wall with 4 Nos metal fastners 12mm dia complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m depth and getting out in soft/ loose soil complete all as specified and directed by Engineer-in-Charge.

Returning filling in trenches including spreading leveling watering and well ramming in layers not exceeding 25 cm thick all complete all as specified and directed by Engineer-in-Charge.

Removing of excavated material not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point all complete all as specified and directed by Engineer-in-Charge.

M&L for fine river washed sand in trenches complete all as specified and directed by Engineer-in-Charge. NOTE: For measurement purpose, punned down thickness shall only be taken.

M&L for laying brick sub class 'B' old size burnt bricks for cable protection of size 230mmx115mmx75mm complete all as specified and directed by Engineer-in-Charge.

M&L for earthing complete with galvanized steel earth plate electrode of size 600x600x6mm thick buried directly in ground (earth pit not less than 2.25m deep below the normal ground level) with top edge of the earth plate not less than 1.5 mtr below normal ground level connected to galvanised earth lead wire 4 mm dia as earth lead connectd by means of bolts, nuts, washers and check nuts all as shown in electrical plate No 3 of MES SSR Part-I, including testing on completion complete all as specified and directed by Engineer-in-Charge. NOTE:- (i) The unit rate shall also included for earth work in hard/ dense soil, PCC (1:3:6) type C1 chamber with CI cover plate 10mm thick including angle iron frame , funnel with GI watering pipe 20mm dia Medium grade, GI protection pipe light grade 15mm dia and wire mesh complete in addition to item No 1 (a) to (e) of preamble (notes) under sub heading earthing, specified on Sl Page No 389 of MES SSR Part-II. (ii) Earthing lead and GI protection pipe beyond 7.5m will be measured and paid separately. (iii) Test points shall be made of GI strip 32x6 mm bridge type mounted on insulators, where ever applicable

Shri H Kivigho Zhimo

Shri Atoshe Tuccu

M/S RAHUL TRADING CO.