Repairing and Painting works

Amount

Dismantling existing plaster including disposal of refuse as directed by the Engineer- in- charge within a distance of 60 m.

12mm cement plaster in single coat on rough side of single/ half brick wall for interior/ exterior plastering in singl;e storey building finished even & smooth 1 cement : 4 coarse sand including all L/M, T&P etc.

Providing and applying plaster of putty 2mm thickness over plasterd surface to prepare the surface even and smooth complete.

Scraping old white or colour wash including disposal of refuse as directed by Engineer-in-charge with in a distance of 60m.

One priming coat and two coat oil bound distemper including supply of all materials, labour and T&P etc.required for proper completion of work.

Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete(.a) 32mm dia

Providing & fixing 600x450mm bevelled edge mirror of superior glass (of approved quality) complete with 6mm thick asbestos cement sheet ground fixed to wooden cleats with C.P. brass screws and washers.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms

P/F C.P. brass Soap Dish with C.P. brass brackets fixed to wooden plugs plastic sleeves with C.P. brass screws.

Providing and fixing 45 cm long unplasticised PVC connection pipe with brass unions.(a) 15mm nominal bore

Providing & fixing CP brass bib cock of approved quality conforming to IS 8931 (a) 15mm nominal bore

P/F 15mm Nominal hole size C.P. brass pillar each cocks.

P/F ball valve ( brass) of approvd quality complete ( high or low pressure with plastic flote) a - 25 m Nominal bore

Providing and fixing gun metal gate valve with wheel of approved quality. (a) 25mm dia nominal bore

Providing & fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS : 8931.(a) 15mm nominal bore

Painting or varnishing on iron work in small areas or new wood work with one coat of ready mixed priming paint & two coat of approved superior quality ready mixed paint of clear synthetic varnish including supply of all materials ,labour, T&P etc required for proper completion of work .(Paint to be used should conform to the ISI no -103-1950.)

P/F C.P. jali for Nahani Trap 100 mm dia including cost of all m/aterail

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) ansparent or dyed to required colour or shade, with necessary screws etc. complete (a) 300 mm x 10mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete (a) 125 mm

Providing and fixing aluminium hanging floor door stopper, ISI marked,anodised (anodic coating not less than grade AC 10 as per IS : 1868)transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

vajid ali