PROVN OF COMMON TOILET IN BLOCK NO 43 AND 45 AT EKTA VIHAR AND PARKING SHED AT FIRE STN LOC BEHIND FIRE STN AND SPECIAL REPAIRS TO DRAIN ANDCULVERT AT ETT NEAR FOLLOWERS QTRS NO EV P 51 AND CERTAIN MINOR WORK AT NDA KHADAKWASLA

Amount

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in any type of soil

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard dense soil

Ditto all as per item No 01 above but in soft disintegrated rock.

Ditto all as per item No 01 above but in Hard rock.

M&L for cement concrete type D2 (1:4:8) (Using 40mm grade stone aggregate) in foundations, filling and mass concrete

M&L for reinforced cement concrete (nominal mix) type B1, (1:2:4) (Using 20 mm aggregate) in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete

M&L for reinforced cement concrete (nominal mix) type B1, (1:2:4) (using 20 mm aggregate) in columns, pillars, piers, posts and struts

M & L for reinforced cement concrete (nominal mix) type B1, (1:2:4) (Using 20 mm aggregate) in beams, cantilevers, bressummers, lintels over 1.5m span

M&L for reinforced cement concrete (nominal mix) type B1, (1:2:4) using 20 mm aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

M&L for providing precast RCC (1:2:4) type B1(using 20mm gde stone ag as in cover slabs for manholes set in CM (1:6) all as ( Note : Reinforcement shall be meashred & paid separately)

Use and waste of formwork to sides of concrete foundations,footings,bases of columns,plinth beams,and similar work,vertical or to batter,rough finished surface

Use and waste of formwork to sides of pillars,posts,strutspiers,columns and stanchions ,rough finished surface

Use and waste of formwork to sides and soffits of floor or roof beam, lintels, cantilevers etc,rough finished surfaces of pillars,posts,strut,piers,columns and stanchions ,rough finished surface

Use and waste of formwork to soffits of suspended slab such as floor slab, roof slab,landings and similar work not exc 200mm thick

Use and waste of formwork to edges of slabs of thickness exc 10cm but n.exc 20cm

M&L TMT Bars 10mm dia and over cut tolength bent to shape required uncl cranking bending and spirally for hooping for colums hooking ends and binding with ms wire n. less than .9mm dia

Ditto all as per item No 16 above but 5mm dia and over upto and incl 10mm dia in stirrups, spacers and binders

S & F for providing MS bands, straps and handles for MH covers and rungs in manholes and similar small articles, all as directed conforming to Fe 290 Gde -E- 165

M&L for precast cement concrete (1:3:6) type C-1 (Using 20mm graded aggregate ) block masonry with solid blocks exc10 cm thick in width and setting in cement mortar (1:6) completein wall complete all as specified.

M&L for precast cement concrete block masonry with solid blocks of PCC (1:3:6) Type C1 n. exc 10 cm in width and setting in cement mortar (1:4)

M&L for damp proof course 40 mm thick PCC (1:2:4) type B-0 to horizontal or vertical surface including necessary form work complete all as specified and as directed. Note : WPC shall be measured and paid separetely under respective items.

M&L for rendering 20mm thick cement plaster in CM (1:4) surface finished even and smooth without using extra cement complete.

M&L for rendering 15mm thick cement plaster in CM (1:6) surface finished even and smooth without using extra cement complete.

M & L rendering 10mm thick on ceilings concrete surface in cement mortar 1:4 finished fair and even without using extra cement complete.

M&L for precast cement concrete louvres and jallies, 25mm thick (mea sured solid), including all mouldings and setting in mortar complete with joints to match,type C0, (1:3:6) using 12.5 mm graded aggregate exc. 10 cm in width and setting in mortar (1:6), complete

Returning , filling, in incl spreading levelling watering and well ramming in layers n exc 25cms in soil in floor/ foundation.

Removing excavated material n exc 50mtr and depositing where directed at a level n exc 1.5 m above the starting point in soil

Spreading and levelling in layers n exc. 25 cm thick and well ramming including watering as required and filling under floors soil / rock obtained from excavation

M&L for hardcore of gauge n exc 63mm deposited spread levelled in layers n exc 15cm thick and rammed to a true surfaces of broken stone & boulders

M&L cement concrete type D2 1:4:8 (using 40mm graded stone aggregate) 100mm thick as in sub floor

M&L for non skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm,in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 20mm thick screed bed in CM 1:6

M&L for glazed, coloured , ceramic tiles,joint free,in vertical surface 350x250x7mm thick thick set and jointed in neat cement slurry and pointed in coloured cement to match including & over 10mm thick rendering in CM 1:4

M&L for PCC (1:3:6) type C-2 as in plinth protection & finishing the surface even & smooth (witout using extra cement ), 75 mm thick complete all as specified & directed.

M&L for 100 mm thick PCC type B- 2, (1:2:4) (40mm graded aggregate) and Spike rolling to surfaces or making impressions of expanded metal

M&L for preparation of new plastered surfaces of walls and applying two coats of cement base paint.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash

M&L for prepartion of new plasted surfaces of wall and applying three coat of white wash.

M&L for providing 20 mm thick (averag thickness) screeding in CM (1:4) over roof slab to slope with water proofing compound, including edges of slabs and vertical surfaces finished evenly to receive WP treatment all as directed by Engineer-in-Charge (Note-integral water proofing compound will be measured and paid separetely )

Supply only intergal water proofing compound

M&L for preparing plastered surfaces @ 1.2 kg/Sqm with primer and applying water proofing treatment on roof wall, edges and vertical surfaces using APP modified membrane 3 mm thick with non woven polyster mat as reinforcement weighing not less than 3.5 Kg/Sqm and applying one coat of aluminium top reflecting coating above the membrane complete all as specified

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

S&F Factory made solid panel PVC door shutter 30 mm thick ( style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of wood grain printed PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing

M&L for aluminium anodised barrel tower bolts of extruded section and fixed 150 mm long

M&L for aluminium alloy anodised sliding door bolt with hasp staples (bolt type and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded section a cast aluminium alloy and fixed 250 mm long

M&L for 100mm long butt hinges cold rolled mild steel medium weight and fixed

M&L for extruded aluminium alloy handles, fabricated type, anodised 150mm long

M&L for tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors 15mm bore of pipes .

M&L for GI tubes med grade galvanised with all fittings fixed complete to wall and ceiling or laid in floors of 20mm dia of pipe.

M&L for tubes, 'medium grade' galvanised, with all fitting and fixed complete laying in trenches 15mm bore of pipes .

M&L for tubes, 'medium grade' galvanised, with all fitting and fixed complete laying in trenches 20mm bore of pipes .

Cutting screwing exiting steel tubing incertion 25x25x20mm tee shot nipple union for branch connection of the internal dia 20mm alteration oraddition if necessary done without taking down.

S&F Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed 15mm bore of pipe

S&F fancy type Bib taps 15mm dia, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed including taking down old one complete all as specified and directed.

S&F 15mm bore of pipe fancy type Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe

S&F in vitreous china ware wash basin white, oval shape size 580 X 400mm (for Hospital use ) including 32 mm CP waste coupling, chain and plug, waste fittings, union and waste pipe 32mm dia or required length and all necessary inlet, out let PVC connections 600 mm complete

M&L for unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe 50mm bore of pipes

S&F watercloset (squatt pattern ) orissa pattern 580 X 440 mm complete including provision of lime concrete bedding

S&F Flush pipe of polyethylene of low or high density or PVC. 32 mm dia,for low level cistern

S&F PVC valveless syphonic action type flushing cistern 10 lit cap low level white with inlet ball valve float and handle including brackets

S&F Hat & coat hooks, solid body ,175 mm to 250 mm with aluminum body fixed in repair

M&L for providing bed to drain pipes 150mm dia in cement concrete (1:3:6) type C2 using 400mm graded stone aggregate including packing under & haunching against the sides of pipes after they are laid & tested.

M&L for providing reinforced cement concrete pipes 150mm dia class NP 2 with collars laid and jointed with cement jointed all as directed by Engr -in -charge.

Cutting into existing manholes for connecting new drains internal dia of pipe 150mm making good to pipe & rendering cutting out existing benching for forming branch channel (1/2 round or 3/4 section in cement concrete (1:2:4) type B-1, smooth finished .

M&L for providing plain cement concrete (1:2:4) type B1 using 20mm grade agg. as in surfaces channels & drains

M&L for providing cast iron soil & waste and vent spun pipes in any length with or without ears with cement joints fixed to walls using pipes 100mm bore pipes

S&F CI bend 100 mm bore with oval access door.

S & F 100 mm size branch piece , single (equal or unequal) ordinary or inverted (spigot or socket type) or with parellel branches.

S&F CI cowl 100 mm size

M&L for 20 mm thick granite (of any type) work (table rubbed and polished) as in platform/ vertical surface (fasia ect.) and like all as directed by Engg-In-Charge.

Labour only for chamferring and rounding the straight cut edges of stone slab such as in steps , platform and other similar situations complete all as specified

S&F rotational moulded polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed in position 1000 ltrs capacity complete all as specified in SSR Part I .

S&F gun metal globe or gate valve with iron wheel screwed both edns for iron pipe of 20 mm dia.

S&F ball valve high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for 20mm dia iron pipe and fixed.(Minimum weight 210gm)

S&F ball valve high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for 15mm dia iron pipe and fixed.(Minimum weight 210gm)

M&L for pre-cast cement concrete block masonry with solid blocks, type C1 (using 20mm graded stone aggregate,in PCC (1:3:6) exc. 10 cm in width and setting in cement mortar (1:6) complete

M&L for preparation of new plastered surfaces of walls and applying two coats of cement base paint over a coat of alkali resistant primer all as specified and directed.

S&F Compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc. Fe 410 -W (Gde- E- 250) quality- A-1

S&F Fe 410 (GdeE-250) quality-A, rolled section Roof trusses (framed), trussed,purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.

M&L for MS Plates,FE 410W,Grade E-250 (plain or chequred) channels,square cut or notched(ordinary and counter sunk)forming holes with riveted,bolted or welded attachment

M&L for pre painted galvalume aluminium zinc coating GI based corrugated /semi-corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall,fixed with self tapping screws as specified

M&L for pre painted galvalume aluminium zinc coating GI based Plain steel sheet 0.5mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall,fixed with self tapping screws as specified

M&L for preparation of new steel surfaces and applying two coats of synthetic enamel paint over one coat of red oxide primer

M&L for forming dummy joint 50mm deepx10mm wide filled with sealing compound grade'A'

M&L for Forming 12mm thick expansion joints filled with preformed bituminous filler and top 30mm primed and sealed with sealing compound grade 'A',in 150 mm thick concrete pavement

Demolition of brick/ block masonry built in Cement mortar

Demolition of unreinforced cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) including cleaning off premises where directed by Engr-in-charge.

Excavating over areas in soft / loose soil, n exc 1.5 m deep and getting out incl bailing out, pumping out or otherwise removing all water / mud / wastes which may accumulate in the excavations, from all causes

Excavating over areas in hard / dense soil, n exc 1.5 m deep and getting out incl bailing out, pumping out or otherwise removing all water / mud / wastes which may accumulate in the excavations, from all causes

Excavating over areas in hard / dense soil, exc 1.5 m n exc 3.0m deep and getting out incl bailing out, pumping out or otherwise removing all water / mud / wastes which may accumulate in the excavations, from all causes

Demolition and breaking up drain pipes ( SWG,AC or RCC pipes ) set in CM 300mm dia.

M&L for RCC (1:1.5:3) type A1 (Using 20 mm graded aggregate) in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete

M&L for RCC (1:1.5:3) type A1 (using 20 mm graded aggregate) in Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses

M&L for RCC (1:1.5:3) type A1 (Using 20 mm graded aggregate) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

S&F Formwork to faces of walls, retaining walls, abutments, parapets and staircase railing and similar work including attached pillasters, buttresses, etc.; vertical or to better

M&L for providing plain cement concrete (1:2:4) type B1 (Using 20mm grade agg) as in surfaces channels & drains

M&L for providing plain cement concrete (1:2:4) type B1 (Using 20mm grade agg). as in coping including weathering slightly, rounded or chamfered angles and throating and necessary use and waste of form work all as directed

S&F Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0

M&L for 100 mm thick PCC (1:2:4) type B1 using 20 mm graded aggregates finished even and smooth without using extra complete all as specified and directed

S&F for collapsible steel gate, consisting of chabbel pickets,pivoted flats bars, top and bottom runners,brass handleetc,as specified erected in position and secuuring runners with holdfasts and brackets complete all as specified and directd.

M&L for marble work 20 to 25mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using including marble dust with admixture of pigment to match as directed & specified

M&L for machine cut cuddapa stone slab 20 to 25mm thick over cement screed base ,laid and pointed with grey cement slurry mixed with pigment to match the shade of the slab incl rubbing and polishing complete including & over 20mm thick screed bed in CM 1:6.

Rounding /moulding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situation.

S&F Stainless steel sink, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever castiron brackets, connecting union etc. overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm

S&F steel plate rack of size of size not less than 750 X 250 X 900 mm made from stainless steel pipe section & steel bars suitable for hanging/fixing to wall.

S&F second class hard wood plain fillets. square, rectangular or triangular in section, wrought, se-cured with screw sectional area exc 13 sqcm but nexc 25 sqcm.

M&L for 12 mm thick Prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination , fixed with screws to timber frame work as shutter..

M&L for Plywood 12mm thick, grade BWR, type BB, fixed with screws to timber frame work

M&L for 75mm long butt hinges cold rolled mild steel medium weight and fixed

S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished

S&F 75 mm size Hasp and staple, mild steel fancy type, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws

Excavation in post holes (or similar holes) each n.exc 0.5 cum as in Hard and dence soil and getting out and removing surplus soil to a distance n.exc 50m

M&L for providing cement concrete type B2 (1:2:4) in foundation ,filling and mass concrete complete as specified.

S&F MS rolled /box sections as in main and cross beams ,columns ,purlins, brackets where connected to common rafters ,fixed with angle cleats or other connecting plates , Fe 410 W ,GRADE E- 250/ box sections complete all as directed.

M&L for MS Wind ties for roof including securing bolts incl all necessary drilling,bolting and similar work conforming to Fe-290,grade E-165

Excavation in post holes (or similar holes) each n.exc 0.5 cum getting out returing filling in and ramming earth or broken rubble mixed with earth around in layers n. exe 25 cm watering and removing surplus soil to a distance n exe 50 m and making good surface as in soft/loose soil all as specified and directed.

M&L for 20mm thick glossy finished cement concrete coloured interlocking pavers,patternsa approved,as in floor or pavements,laid in 25mm thick sand coushining all as specifed and directed.

M&L for steel work in tubular trusses including specila shaped washer etc,complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St 240 All as per specified and directed.

M&L for point wiring on PVC casing and capping confirming IS:3419-1988 with the help of multistranded unsheathed FRLS copper cable 1.5 sqmm 650/1100V grade confirming to IS:694 -1990 adhereing to colour code including earth wire of the size 1.5 Sqmm multi-stranded green colored connecting properly to the socket/ earth terminals with suitable terminal PVC boxes as required at site for the following :- (a) One light /fan point controlled by one switch one way

S&F switch piano Conform IS 4615-1968 flush type 5 Amps single pole one way.

S&F ceiling rose surface shall comply with IS :371-1979 Bakelite 60x 25 mm two to three terminals plates and of outside diameter not less than 63.5mm.

S&F polycarbonate angle holder retrofit type suitable for CFL/LED bulb of B-22 base including 01 nos 18/20 watt LED Bulb all as specified and directed by Engineer-in-Charge.

S&F LED tube light with diffused optics ultra bright LED tube light 18/20watt with high efficiency,integrated aluminum heat sink suited for installation in existing T8 tube light with G13 lamp holders all as specified.

S&F in 1x18/20W,230V surface and wall mounted batten suitable for installing LED Tube including connecting up with twin core twisted flexible copper condctor cable from ceiling rose complete all as specified .

S&F LED building security light fiitting 25W,IP-65 protection made up of die cast alluminium housing with high power LED as lighting source and lens complete fixing with bracket of adequate length, incl electrical connection from connector to light fitting. and fixed to pole/wall with necessary MS clamp accessories complete all as specified and directed by Engr-in-charge. Make:Havells/Philps/Luker

S&F MCB DB 04 way SPN double door sheet metal enclosure factory made suitable for MCB DB's 240 volts with 200 amp rated busbar, neutral & earthing link bar,surface mounting complete including taking down the existing DB of any type & size alongwith its accessories by removing from existing circuits and refixing the new DBs and circuits complete as reqd at site. Make:Legrand/L&T

S&F MCB SP 6 to 32 Amps 240V,10 KA breaking capacity , C curve as per IS/IEC 60898-1 2002 with IP 20 protected terminals all as specified including complete connection with copper /aluminium cable lugs with suitable size for incoming and outgoing. Make: Legrand/L&T

M&L for laying XLPE underground cable 10 sqmm 2 core armoured sheathed with PVC cable stranded aluminium conductor 1100 volts grade

Supply and filling of sand / crushed stone dust filling including gently punning around cables in trenches for cable protection complete all as specified and directed by Engr-in-charge.

Supply and laying reinforced precast concrete cable cover, Class LV, Type 1, flat, size 250mm x 150mm x 40mm complete all as specified.

M&L for cutting of existing road/ hard standing by providing suitable T&P to make suitable size bore for fixing 50 mm dia pipe in road crossing etc. including the cost of making good the disturbed surface and matching with existing (Chequered tiles/Road/PCC) complete all as specified.

S&F GI tubing light grade 50 mm dia ISI marked with all fittings laid in trenches and fixed pole by flat iron clamps, nut,bolt,washers suitable size complete all as specified and directed at size.

M&L for exhaust fan of sweep 300 mm,single phase 240V of not less than 3 star BEE star rating , louvers and making hole as per the required size of the exhuast fan and making good the disturbed surfaces and fixing to the wall with proper fasetner arrangements and all accessories.

M & L for earthing complete with GI earth plate electrode 600 x 600 x 6mm thick burried directly in ground (earth pit plate kess than 2.5 mtrs below ground level) with top edge of the plate not less than 1.5 mtrs deep below normal ground level, connected to galvanised earth wire 4mm by means of bolts, nuts check nuts to earth test point including necessary PCC (1:2:4) type B-1 pit, cover frame, GI pipe 15mm dia light grade with funnel and locking arrangement complete all as specified.

Harish Enterprises

ELIEYAS TRADERS