ADDITION/ALTERATION AND SPECIAL REPAIRS TO BLDG NO P-12 (OVER HEAD RESERVOIR) AND P-64 (POS MD ACCN) AT HQ 31 WEU AND ADDN/ALTN AND SPL REP TO FIRE FIGHTING SYS AND FIRE ALARM AND HEAT DETECTION SYS WITH VISUAL INDICATION IN CERTAIN BLDG AT HQ 31 WEU

Amount

Taking down cement plaster on brick or stone walls & ceilings of concrete surfaces etc, including raking out joints, hacking for key, scrubbing down with water , etc complete all as specified and directed. Note for Item No 01.00 to 19.00 : The work to be executed upto and including 24.00 mtr height

M&L for 10 mm thick polymer modified ready mix cement based plaster on the wall surfaces including finishing surfaces even and smooth complete all as specified and directed Note: (i) The thickness of plaster specified above is the minimum thickness and the quoted rates shall also be deemed to include for provision of dubbing of the surfaces with ready mix plaster and nothing extra shall be payable on this account. (ii) This item shall be operated only for the locations where the thickness of existing adjoining plaster is to be matched

Chipping,removing carefully all the loose/damaged concrete including plastering from deteriorated /damaged concrete portions of columns, beams, slabs or any other RCC members etc by doing manually with wooden mallet (Carefully so that sound concrete should not be distrubed) and expose the sound concrete, de-rust existing reinforcement with electrically operated rotary grinders with cup-brush, wire brush or sand paper. Use portable air blowers to make the surface free from loose material, dirt, etc Complete all as specified and directed. Note: Item no.3 will not be applicable for the locations/areas where Item no.1 is applicable.

M&L for preparation of old surfaces of walls etc. including removing loose dirt, mortar, dust etc and applying one bond coat of epoxy bonding agent & cement in 1:1 ratio for bonding old and new concrete on damaged surface applying polymer modified mortar in CM 1:3 complete all as per manufacturers instructions including all necessary scaffolding or staging as required including mixing of polymer latex adhesive 15 % by weight of cement and average thickness 20 mm etc complete all as specified and as directed (1)To achive required thickness repeat this step after 24 hrs as required (2) Keep the surface moist using water for 5 to 7 days etc complete all as specified and as directed MAKE :- Epoxy bond agent shall be Krishna Conchem, Dr Fixit Chemistik & M C Bauchemie

M&L for preparation of old surfaces of walls etc. including removing loose dirt, mortar, dust etc and applying one bond coat of epoxy bonding agent & cement in 1:1 ratio for bonding old and new concrete on damaged surface, including polymer modified mortar in CM 1:3 complete all as per manufacturers instructions including all necessary scaffolding or staging as required including mixing of polymer latex adhesive 15 % by weight of cement and average thickness 40 mm etc complete all as specified and as directed (1) Use the electrical mixer to get homogeneous mixture of bond coat surfaces (2)To achive required thickness repeat this step after 24 hrs as required (3) Keep the surface moist using water for 5 to 7 days etc complete all as specified and as directed MAKE :- Epoxy bond agent shall be Krishna Conchem, Dr Fixit Chemistik & M C Bauchemie

M&L for preparation of old surfaces of walls etc. including removing loose dirt, mortar, dust etc and applying one bond coat of epoxy bonding agent & cement in 1:1 ratio for bonding old and new concrete on damaged surface, including polymer modified mortar in CM 1:3 complete all as per manufacturers instructions including all necessary scaffolding or staging as required including mixing of polymer latex adhesive 15 % by weight of cement and average thickness 60 mm etc complete all as specified and as directed (1) Use the electrical mixer to get homogeneous mixture of bond coat surfaces (2)To achive required thickness repeat this step after 24 hrs as required (3) Keep the surface moist using water for 5 to 7 days etc complete all as specified and as directed MAKE :- Epoxy bond agent shall be Krishna Conchem, Dr Fixit Chemistik & M C Bauchemie

M&L for providing TMT bars any dia in various structural RCC elements like columns, beams, Slabs etc. including cutting, bending, fixing of bars with welding/ tying as required at site with & including binding wires etc. and all relevant works like anchoring of the bars in the existing RCC Members, complete all as specified and directed.

M& L for preparation of new plaster/concrete surface of walls ,chajjas, soffits & beam including necessary scaffolding and applying two coats of 100% anti fungal acrylic exterior emulsion paint over a coat of primer including necessary scaffolding up to 24 m height, complete all as specified and directed.

M&L for prepration of surfaces by cutting V groove all along the crack and seoration gap , removing , all loose materials wash down by portable water applying bond of epoxy bonding agent of M/s Chemistic or Dr.Fixit or equivalent & cement in ratio 1:1 for bonding old and new concrete filled the gap by polymer modified mortar in CM 1:3 including polymer latex adhesive complete all as specified and directed.

Drilling and fixing teflon noozzles in RCC Members , including , drilling holes , drilling 12 mm dia , 50 to 100 mm deep holes in structural members at the interval of 300 to 500 mm staggered manner in RCC structural element , cleaning of holes , clean the holes by air blower prior to fixing the noozles, insert 12 mm dia Teflon nozzels in cleaned holes ,External end of nozolles to be machine to recive outlet of grouting gun , fix it inside the holes by applying thixotropic epoxy putty to ensure complete sealing , cure the system for min 12 hrs cutting of nozzles by chisel after completion of grouting without damaged structural element etc complete all as specified and as directed

M & L for Grouting injecting low viscosity high moleculer weight thermosett /monopol of Krishna Conchem or equivalent polymer by pressure and using injecter with accessorises till nozzles refused the accept the grout including, mixing of materials, quantities as per mfg instruction by weight batching grouting fill the grouting gun with material maintain desired pressure in the gun air by compressor maintain the pressure at exit ( 3 to 4 kg / cm2 ) by monitoring pressure gauge at exit ., grout the material through pre fixed nozzles in the structural elements till its refusal . seal the nozzles with putty after the refusal , moniter leakages through other nozzles while grouting and seal them as per requirement complete all as specfied and directed.

M&L for cleaning existing reinforcement with wire/ rotary wire brush to a shining bright finish, making the surfaces free from loose material, dirt etc complete and applying two coats of alkaline rust converting primer conforming to ASTM-B-117 of make. "Feovert" of "Krishna Conchem" OR "Roff Rust Cleaner' of 'Pidilite' OR 'Shali Rustoff' of 'STP Ltd', on rebars with time interval of 1 hour between the coats, complete all as specified and directed. Note :- Mode of measurement: superficial area covered between the end to end reinforcement bars (i.e., concrete area excluding all side covers) will be measured.

M&L for Anticorrosive Treatment to Reinforcement using IPNET-RB of M/s Krishna Conchem or Epoxy Zinc Primer of M/s. Dr. Fixit by application on exposed reinforcement in two coats with time interval of minimum 4 hours between each coat. The application shall be done by brush after cleaning/wire brushing to the exposed steel surfaces complete all as specified and directed. Note :- Mode of measurement: superficial area covered between the end to end reinforcement bars (i.e., concrete area excluding all side covers) will be measured.

Providing and applying concrete penetrating, migratory bipolar corrosion inhibitor EPCO KP-100 conforming to ASTMG-109 of Krishna Conchem or equivalent make by brush/spray with dosage of 4Sqm/ ltr, over the entire chipped off / exposed concrete area including material, equipment, labour etc. complete in order to arrest further corrosion of reinforcement bars. The application of EPCO-KP-100 of Krishna Conchem or equivalent make shall reduce the corrosion in terms of columns by 30% minimum upon migration through the embedded side of concrete as measured by mA - hrs complete all as specified and directed.

Providing & applying a coat of structural grade epoxy bond coat EPIBOND 21-LP of Fosroc or equivalent having excellent water and alkali resistance and has long tack free time of more than 120 minutes by brush conforming to ASTM-C-882-87 to the prepared concrete surface to be repaired / strengthened. This is applied prior to the application of polymer repair mortar / epoxy mortar / Micro concrete to have monolithic action between old concrete surface and new concrete surface complete all as specified and directed.

M & L for making up lost section of concrete/mortar with thixotropic repair mortar of Krishna Conchem or equivalent is one component thixotropic dual shrinkage compensated fibre reinforcement formulation for structural members. Built up section by hand packing as per manufactuer specification , applied by mean of hand gloves by expert applicator , the rehabilitated surface should be free from air gaps, voids should be in line with existing required line with existing surface, incl curing cleaning the area etc, complete the work should be carried out with all the safety measure like helmet, safety belt and adequate labour insurance under the supervision of qualified engineer etc. complete all as specified and directed.

M&L for casting & repairing of excessively damaged distressed RCC members (exceeding 60mm in thickness) with prebatched, prepacked, single component ready to use microconcrete from M/s. Krishna Conchem (Molith MC) or equivalent of Dr. Fixit or Fosroc as approved by GE at any level and at any lead or lift as directed including prefabricated water tight formwork, centering, scaffolding, also including mixing , laying, levelling, finishing, curing etc as per manufacturer's specifications complete all as specified and directed. Note : For payment purposes, actual weight of mircoconcrete used shall only be considered

M&L RCC M-30 (Design Mix) (using 20 mm graded aggregate) in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc basement slabs, under-reamed piles and mass concrete etc all as specified and directed. Note : Design mix shall be carried out from approved lab such as IIT/ NIT/ SEMT Pune or any NABL approved lab.

M & L for two coats of water proof paint inside OHT of approx 20.00 mtr of food grade paint materials from Pidilite, Dr Fixit or STP or Krishna Conchem or equivalent make all as specfied and directed.

Surface excavation n exc 30cm deep and averaging 15cm deep and getting out in loose soil complete all as specified and directed.

Removing excavated material exc 1.50 KM but n.exc 5 KM and depositing complete all as specified and directed.

M&L hardcore of gauge n exc 63 mm broken stone or boulders deposited spread and levelled in layers n exc 15 cm thick, watered and rammed to a true surface etc compelete all as specified and directed

M & L for plain cement concrete 1:3:6 type C2 using 40mm graded aggregate as in foundations, filling and mass concrete etc complete all as specified and directed.

M&L for 60mm thick pre cast concrete coloured with glazed finish(Lacquere finished) interlocking paver block of any size and shape of M-35grade , having compressive strength 30 N /mm2, shade as approved by complete all as specified and directed.

M & L for sand filling under floors or in foundations including watering and consolidation or sand cushioning for cable protection by gently punning down manually complete all as specifed and directed.

M&L for rendering 15mm thick in CM (1:6) on fair faces of brickwork or concrete surfaces,and finished the surfaces even & smooth including sagol finish layer complete all as specified and directed

M&L for rendering 20mm thick in cement mortar 1:4 on brick or concrete surfaces, on walls, laid in two layers, 1st layer 15mm thick and finishing layer 5mm thick mixed with integral water proofing compound @2 % by weight of cement content of finishing layer, finished fair and even without using extra cement , additional thickness provided as floating/setting coat, including all necessary scaffolding / staging as required complete all as specified and as directed

M & L rendering 5 mm thick in CM 1:3 on ceiling surfaces finished even and smooth including thin layer sagol finish complete all as specified and directed

M& L for preparation of newly plastered surface and applying three coat of white wash on ceilings complete all as specified and directed

M & L for preparing old decorated surfaces of wall (plasterered or unplastered or previously white washed) & applying two coat of oil bound distemper with white cement base wall care putty complete all as specified.

M & L for preparing old decorated surfaces of ceilings(plastered or unplastered or previously white washed) & applying three coats of whitewash complete all as specified.

M & L preparing new surfaces of walls applying two coat of oil bound distemper with white cement base wall care putty complete all as specified & directed

M& L for complete removal of existing painting by scraping, washing rubbbing etc surface of walls ,chajjas, soffits & beam including necessary scaffolding and applying two coats of 100% anti fungal acrylic exterior emulsion paint over a coat of primer etc including necessary scaffolding up to 24 m height complete all as specified and directed

S&F towel rail 600mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (Min wt 190 gms) complete all as specified and directed.

S & F in repairs harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc complete all as specified and directed.

S & F in repairs Vitreous China wash basin, white, flat back, size 580x450 mm including brackets, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe and tap complete all as specified and directed.

S&F floor door stopper of aluminium alloy body overall length of cover plate 140 mm and tonque anodised with hard drawn steel spring fixed in floor complete all as specified and directed.

Taking down carefully aluminium sliding window shutters including existing rubber gasket complete and re-fixing the shutters same in existing position after replacement of broken glass/stainless steel wire mesh with rubber gasket and area of window exc 1.20 sqm but not exc 3.78 Sqm in each including necessary scaffolding etc complete all as specified and directed. Note: Glass & stainless steel wire mesh will be measured and paid separately

Taking down carefully aluminium sliding window shutters from the frames or chowkhat and supply and fix New locking arrangement in place of old one and re-fixing the same shuters in existing position after repair work or replacement of new locking arrangement and necessary scafolding etc complete all as specified and directed

S & F aluminium anodised grills of approved design for window/ventilators/balcony and fixing with F/U channel for window, ventilators, balcony opening in architectural or rectangualr type design in existing building, including drilling as required in RCC sections/ any type of masonary, complete all as specified and directed.

Supply only 3.00 mm thick sheet glass, ordinary quality, in squares not exc 0.5 Sqm each pane, complete all as specified.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperature 1.40mm and fixed in repairs with stainless steel wire staples complete all as specified and as directed.

Taking down chowkats or frame with shutters ( without taking off shutters from the frame ) not exceeding 1.5 Sqm each including complete all as specified and directed.

Taking down chowkats or frame with shutters ( without taking off shutters from the frame ) exceeding 1.5 Sqm but not exc 4 Sqm each including complete all as specified and directed.

S& F second class hard wood , plain ,soild ,straight chowkats and frames, wrought , rebated on soild rounded or chamfered , put together with glue pinned at joints etc complete all as specified .and directed

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with Square tube, supply and fixing in opening as per specification given under SSR Part II 2010 including making good the disturbed surface all as specified and directed.

M&L for factory made solid panel PVC door shutter 30mm thick style consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rails,on either side and as gap insert for top rail and bottom rail on either side as gap insert for top rail & bottom rail panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with cement solvent supplying and fixing in the frame at site as per specifications and drawing given under SSR Part II 2010 complete all as specified and directed.

S&F 35 mm thick plain , framed ,panelled shutters ( any number of panels),in 2nd class hardwood,with panels of timber flat on both sides (feather edged) ,or of veenered particle board medium density, wood particle board with commercial face veneers supplied and fitted to chowkats complete all as specified.

S & F 35 mm thick glazed and skeleton shutters, in 2nd class hardwood, open rebated and prepared to receive glass, gauze etc,without sash bar edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24(a) complete all as specified and directed.

M& L for preparation of newly or previously untreated surfaces of wood or wood based surfaces of any description not other wise described , over10 cm width or girth and apply two coats of synthetic enamel paint over one coat of pink primer etc complete all as specified and directed.

M& L for preparation of old surfaces wood or wood based surfaces of any description not other wise described , over 10 cm width or girth and apply two coats of synthetic enamel paint over one coat of pink primer etc complete all as specified and directed.

M&L for treating with tar or coal tar black paint on back of chowkats area exc 0.10 Sqm but not exc 0.5 Sqm each complete all as specified and directed

M&L for treating with tar or coal tar black paint on back of chowkats, ends of posts, holdfasts etc. area not exc 0.1 Sqm each complete all as specified.

S&F bands, straps , supports or stays for rain water, ventilating pipes including bolts, clamps, hold fasts etc and similar small articles to Fe-410-0 or Fe-310-0 all as specified & directed.

M&L PCC (1:2:4) type B1 using 20 mm graded stone aggregate as in bed block, bed plate etc including necessary form work complete all as specified and as directed.

S&F 150 mm extruded aluminum alloy handles fabricated type anodised complete all as specified and directed

S&F 100 mm size stainless steel hinge medium weight complete all as specified

Dismantling floor, hearth or wall tiling including cement mortar, bedding but not backing removing serviceable tiles to store and rubbish off the premises all as specified and directed .

M&L non skid coloured ceremic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, as in floors over screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and as directed.

All as per Item No 60.00 here-in-above but screed bed or bedding layer of mortar 10 mm in cement mortar 1:4 on walls surfaces, such as skirting, dados etc. complete all as specified and as dircted.

S& F coloured glazed ceramic tiles 350 x 250 x 7mm/450x350x7mm thick in dado/ skiting etc set and jointed in neat cement slurry and pointed in coloured cement to match, over and incl 10mm thick backing coat in CM 1:4 complete all as specified and directed .

M & L for Plain Cement Concrete tiles with grey cement and no pigment 20cm x 20cm x 20mm thick, machine pressed set jointed and pointed in neat cement slurry in floors, and cut and polished over screed bed or bedding layer of mortar 15 mm in cement mortar 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface completed all as specified and directed.

M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab over 10mm thick backing coat in CM 1:4 including rubbing and polishing complete all as specified and as directed.

M& L for machine cut kota stone slab flooring 20-25 mm thick over screed bed over bedding layer of mortar 15 mm in cement mortar 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface mixed with pigment to match the shade of the slab including rubbing and polishing

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.

S&F in repairs 150 mm size aluminum anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F in repairs 300 mm Aluminium alloy , anodised , sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet , cast , exctruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified

S&F in repairs 15mm bore bib taps cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified and as directed.

S&F in repairs 15mm bore stop valve cast copper alloy screwed high pressure with crutch or butterfly handle, screwed both end for iron pipe or for union complete all as specified & directed

S&F in repairs 15mm bore pillar taps,chromium plated, cast copper alloy screwed high pressure with crutch or butterfly handle, screwed both end for iron pipe or for union complete all as specified and directed.

S & F in repairs 10 litres PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

Supply only integral water proofing compound

Disconnecting of up to 1000 litres capacity existing tanks, stacking safely for re-use (or lowering if required) and hoisting, reconnecting and refixing in position complete all as specified.

S&F in repair 15mm bore GI Steel tubing medium grade with all fitting to walls & ceiling or laid in floors complete all as specified and directed.

S&F in repair 20mm bore GI Steel tubing medium grade with all fitting to walls & ceiling or laid in floors complete all as specified and directed.

S&F Swivel shower of PTMT any colour for fixing with 15mm pipe. (Minimum weight 40gms) in repairs complete all as specified and as directed.

M&L Grating doom 100mm dia of PTMT (Minimum weight 25gms) in repairs complete all as specified and as directed.

S & F in repairs 110mm bore PVC (SWR) pipes double socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

All as per item No 79.00 above but 75mm dia complete all as specified and directed

S&F PVC (SWR) bends of 110mm bore complete all as specified and directed

S & F for 75 mm dia bend complete all as specified and directed

S & F PVC (SWR) vent cowl of 110mm bore complete all as specified and directed

S&F 75mm bore PVC (SWR) branch piece single (Single Y ) equal or unequal complete all as specified and directed

S&F 110mm bore PVC (SWR) branch piece single (Single Y ) equal or unequal complete all as specified and directed

S&F 75 mm bore PVC (SWR) branch piece, double (double Y ) equal or unequal complete all as specified and directed

S&F in repairs sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm etc complete all as specified and directed.

M&L for special treatment of sunken portion of WCs and Bath room as per following stages:- Stage 1 :- Demolition of WC including lime concrete and cement concrete coba etc and preparing the surfaces of existing sunken portion of WCs or bath etc with wire brush to remove all loose dirt, oil grease etc . Stage 2:- Providing 10mm thick plaster in CM 1:4 with chemical of Dr. Fixit Pidicrete URP or plaster seal of STP Ltd Stage 3:- Applying Dr Fixit Primseal primer or STP Ltd(and allow to dry for 8 hours) under torch dry condition Stage 4:- Applying two coats of water proofing decorative elastomeric coating system of Dr Fixit Raincoats with DFT 100 Micron or shalicry 215 of STP(The surface after painting one coats shall be allowed to dry for 6 hours before next coats) is applied all as per manufacturer instruction Stage 5:-Again rendering 10mm thick in CM 1:4 mixed with Dr Fixit Pidicrete URP or plaster seal of STP Ltd. Stage 6. All CI joints shall filled with mixture of cement fine sand and plaster seal of STP Ltd or Dr Fixit pidicrete URP. Stage 7:- Making holes in wall and fixing 600mm long 20mm dia GI spout for draining the surplus water if any

M & L for plain cement concrete 1:5:10 Type E2 (using 40mm graded stone aggregate) as in filling in sunken floor etc complete all as specified and directed.

S & F Wash down water closet (Pedestal pattern), complete white (excluding fixing bolts, flushing cisterns and flush pipe) complete all as specified and directed.

S & F PVC connections 15mm size with PTMT nuts of length 450mm etc complete all as specified and directed.

S&F cast iron Nahani trap 100mm dia out let including grating connecting jointing to waste pipe with lead jointing and taking out existing unserviceable traps by hacking out concrete joints and making good of surfaces complete all as specified and as directed .

Dismantling boarding any description fixed in any position with nails complete all as specified and directed .

S&F 18/19 mm thick prelaminated particle board both sides , interior grade , of approved shade and pattern fixed with screws to timber frame with beading piece for cupboard and shelves complete all as specified and directed.

S & F for continuous (piano) hinges, mild steel, bright finish or electrogalvanised width of flaps 30mm (when open) complete all as specified and directed.

S & F for 125mm aluminium handles, cast type, anodised complete all as specified and directed.

M & L for Granite (of any type) tiles 20 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed

Taking up old CI/DI pipe of upto 100 mm bore and connections including cleaning and setting a side etc complete all as specified and directed

Taking up or down steel water tubing of upto 80 mm bore and connections including cleaning and setting a side etc complete all as specified and directed.

M&L for DI pipe Class "K-7" 100mm (4") dia with flanged type ends centrifugally cast any length laid in trench, wall, floor including required Gasket, nut bolts as required etc complete all as specified and directed.

M&L for DI fittings confirming to IS 9523/2000 of class K-12 upto 150mm bore such as bends, tapers, tee pieces single branch, collars etc complete all as specified and directed.

Supplying, laying, connecting and testing of GI tubing medium grade of 80 mm dia with and including all fittings such as bends elbows, tees, short pieces, connectors, check nuts, diminishing pieces, caps and plugs, unions,etc fixed complete laid in trenches / along the walls / ceilings / floors / ducts / on pillar post including MS clamp of size 50x6mm of required size for support of pipe all as specified and directed

Supply, fixing, jointing and testing of 100 mm (4") dia, CI Sluice Valve heavy duty PN 1.0 with iron wheel head jointing, coupling both ends for cast iron pipes including nuts, bolts, rubber gaskets etc including taking down old unserviceable sluice valves complete all as specified and directed

M&L for water level indicator for RCC OH tanks of size 2.52 x 0.3 mtr made out of MS angle iron 25x25x4mm MS flat iron of 4mm thick, 150mm dia MS oval shaped float ball assembly with required length of staranded steel rope 10mm dia, pulley, MS indicator and slot and accessories required for smooth functioning and applying black bituminous paint and making letter and figure with black/white paint to the level indicator over black paint back ground surface including taking down old indicator assembly complete all as specified and directed.

Supply and fix single dome aviation obstruction LED light fitting including mounting arrangement of length 1.00 meter complete all as specified and directed

Supply & Fixing air termination Aluminium rod 12 mm dia, 300 mm long for lightening conductor including base plate with all necessary nut bolts and drilling job complete all as specified and directed

Supply and fixing of GI pipe light grade of size 40 mm bore for laying in trenches/floors or walls including all fittings for fixing complete all as specified and directed

Supply & fixing for aluminium strip 25 x 3.15 mm size on wall/roof or buried in ground including all saddles, insulators, screw, nut bolts for roof conductor and down conductor complete all as specified and directed

M&L for test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hex. head screw complete all as specified and directed .

M&L for lightening conductor assembly made out of GI pipe light grade of size 40 mm bore along with welded flange at one end & GI reducer socket at another end connected with GI pipe light grade of size 40 mm bore with one end GI reducer socket to connect air termination & connector for earth strip duly fixed with necessary nuts bolts & washers in PCC 1:2:4 type B0 30cm x 30cm x30cm complete all as specified and directed Note : GI pipe 40mm & air temination shall be measured & paid separately under relevant items

M&L for Earthing complete with M.S. galvanized earth plate electrode 600 x 600 x 6 mm thick buried directly in ground (earth pit not less than 4.25 M deep below normal GL) with top edge of the plate not less than 3.5M below normal GL, connected to Galvanized earth strip 32x6mm upto 7.5 mtr with protection pipe by means of bolts, nuts, check nuts & washers of GI or steel incl excavation, PCC (1:3:6) type C-1 chamber with RCC cover (1:2:4) type B0, 40 mm thick reinforced with 6 mm dia bar, 3 Nos. both way, 40mm dia light grade GI protection pipe, funnel with wire mesh,watering pipe of size 20 mm dia med. grade, lugs, main Earthing lead upto 7.5 mtr incl. Charcoal dust, salt etc. all as shown in electrical plate No. 3 of SSR Pt-I 2009 specification etc complete all as specified and directed.

Supply and lay XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 4 Sqmm 2 Core complete.

Taking down copper/ aluminum point wiring surface type, concealed type, flame proof type (Light/Fan/Socket or power) complete including fixtures and fittings such as switches, ceiling roses, pendants, regulators, socket, light fitting etc. Removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces to walls floors etc complete all as specified and directed.

M & L for point wiring with PVC insulated FRLS unsheathed 1100 Volts grade single core multistranded copper conductor cable 1.5 Sqmm drawn in and including casing-caping and accessories, fixed on wall / ceiling etc with necessary fixing accessories and earth continuity conductor cable of 1.5 Sqmm size connected to common earth and earth dolly including 1.6 mm thick pressed steel terminal boxes concealed in wall covered with laminated sheet top cover 3 mm thick for mounting switches / sockets / fan regulators fixed with Cadmium plated machine screws all as specified for one light / fan / bell point controlled by one switch.

All as per Item No 114.00 here-in-before but for one 5A 2pin/3pin socket out let multipurpose on the same board with other switches.

All as per item No 114.00 here-in-before but for one 5A 2pin/3pin switch socket out let multipurpose on independent Board.

All as per item No.114.00 above but wiring complete with 2.5 Sqmm for 3 pin 15A socket multipurpose on independent board

S & F Switch Piano, flush type, single pole, one way, 5 Amps, 230 Volts

S & F Bell push flush type 5 amp, 250 Volts

S & F Ceiling Rose, surface bakelite, three terminals, AC, 230 Volts

S & F Switch Socket combination 2 in 1, 5 Amps, 5 pin multipurpose, flush type, 230 Volts

S & F Switch Socket combination 5 in 1, 15 Amps, 6 pin multipurpose, flush type, 230 Volts

S & F Ceiling fan regulator electronic stepped type, AC, 230 Volts, flush type

Supply and fix bell ding dong AC 230 V single pole.

S & F in repairs MCB DB 8 way SPN, double door, vertical type, IP - 53 with 200 Amps rated bus bar, AC and connecting up complete all as specified.

S & F MCB SPN 40 Amps, 240 / 415 Volts, 50 Hz, 10 KA Breaking capacity

S & F MCB SP 6 to 32 Amps, 240 / 415 Volts, 50 Hz, 10 KA Breaking capacity

S&F in repairs Surface, hanging and wall mounted batten (Double side connection) suitable for LED tube 20/22 watts, 230 volts alongwith tube rod 22 watt (double side connection), including fixing mounting blocks 2 Nos, 15 mm MS conduit, 1.5 sqmm 3 core PVC insulated copper conductor cable including fixing arrangements complete . The fitting shall conform to Cat No. REGALBATTENT8UPTO1X22WDSBSWH for fitting and CRYSTAL 1213T8DSTL20WLED865SGLASS for tube rod of Havells /Bajaj/Crompton

S&F in repairs surface and wall mounted 10 Watt LED batten with LED rod complete, extruded aluminium housig provided for efficient heat dissipation with polycarbonate diffuser & interrated electronic driver including fixing arrangements and complete . The Fitting Shall conform to Cat no - LUMILINEPLUSBS10WLED865SPCSS of Havells / Crompton/Bajaj

M & L for Earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers, including excavation, PCC (1:3:6) type C-1 chamber with RCC cover (1:2:4) type B0, 40 mm thick reinforced with 6 mm dia bar, 3 Nos. both way, 40mm dia light grade GI protection pipe, funnel with wire mesh,watering pipe of size 20 mm dia med. grade, lugs, main Earthing lead upto 7.5 mtr incl. Charcoal dust, salt etc. all as shown in electrical plate No. 3 of SSR Pt-I 2009 specification all as specified or indicated including testing on completion complete all as specified and directed

M&L for sub main wiring with two single core 4.0 Sqmm PVC insulated FRLS multistranded copper conductor cable 660/1100 volts grade down in through non metalic PVC casing caping with and including PVC insulated 4 Sqmm single core single strand copper conductor as continous earth wire in green colour connected to common earth dolly all as specified and as directed Note : 1. Two runs of cable, one run of earth wire, one run of PVC casing capping will be measured and paid one unit.

M&L for sub main wiring with two single core 1.5 Sqmm PVC insulated FRLS multistranded copper conductor cable 660/1100 volts grade down in through non metalic PVC casing caping with and including PVC insulated 1.5 Sqmm single core single strand copper conductor as continous earth wire in green colour connected to common earth dolly all as specified and as directed Note : 1. Two runs of cable, one run of earth wire, one run of PVC casing capping will be measured and paid one unit.

S&F in repair/replacement of building Security light fitting made up of pressure die cast alluminium body with mid power 30 Watt LED as lighting sources and PC cover having Top opening seperate driver compartment with IP66 protection and impact resistance of IK07 including fixing arrangements complete all as specified and directed.

S& F in replacement of GI steel tubing medium grade 40 mm dia and length up to 1.5 meter bent to shape of offset angle upto 45degree for fixing of security /street light fittings including MS clamps made of 32mm x5mm flat iron, nuts , bolts, etc complete all as specified and directed.

Taking Down Ceiling fans 1200/1400 mm sweep and Exhaust Fan any size transporting to store for safe custody for reuse or for depositing at the MES Yard.

Fixing only ceiling fan 1200/1400 mm sweep and Exhaust Fan any size as obtained from taking down vide Ser No 136.00 herein before including painting of celing fan and Exhaust fan complete all as specified and directed

Supply & fix Heavy duty Metallic body Exhaust fan of sweep 300 mm, 900 RPM with frames, blades, mounting anchor fasterners aluminium louvers made of aluminium sheet of 0.5 mm thickness provision of three core 1.5 sqmm copper cable from ceiling rose to fan , making opening of requird hole with suitable size in cement mortar brick wall/RCC for fixing of exhaust fan, making good the distrubed surfaces in CM 1:4 including scafolding if any required to carry out the work in building of height up to 20 Meters complete all as specified and directed .

Supply and Laying or fixing or passing through pipe, XLPE/PVC insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area 35 Sqmm 3.5 core including necessary connection and providing cable lugs as required including disconnection/taking down of existing cable all as specified.

Excavation in trenches not exceeding 1.50 m wide and n.exc 1.5 m in depth for foundation of poles, cable etc, not exc 10 sqm on plan and getting out in soft/loose soil including taking out brick protection etc complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25cm thick complete all as specified and directed.

Supply and laying un-reinforced precast concrete cable cover class LV, type-I, flat size 250 mm x 150 mm x 40 mm laid in trenches all as specified.

Design, supply and fixing of new conventional 16 Zone Main Fire Alarm Control panel complete with annunciate windows for all individual zones, No/NC relay contacts for repeater panel in each zones and inter changeable zone modules, monitor module, test module for all zones test for fire open and short circuit test, All call facility for emergency evacuation, and visual indications with all standard specifications including taking down old unserviceable panel complete all as specified and directed. Make : - Ravel, Safetech, Minimax, ECD, ANG

Supply, installing and testing of Multi Sensor Smoke/Heat detector with flashing LED complete with mounting base, detector junction box and all fixing accessories including taking down old unsv detector complete all as specified and directed. Make: Apollo/ Hochuki/ System Sensor/Edward

Supply and fixing of 1.5 Sqmm x 2 Core Copper multistranded FRLS Armoured cable ceiling/along the wall/ floor/ ground etc including bens, end caps, junction boxes and complete with all fixing accessories including taking down old unsv cable complete all as specified and directed.

Supply and fixing of 1.5 Sqmm x 4 Core Copper multistranded FRLS Armoured cable ceiling/along the wall/ floor/ ground etc including bens, end caps, junction boxes and complete with all fixing accessories including taking down old unsv cable complete all as specified and directed.

Supply, installing and testing of Manual Call point (Pill box complete with hammer chain and all fixtures.) including taking down old unsv MCP complete all as specified and directed. Make : - Agni, Safetech, Minimax, ECD

Supply, installing and testing of electronic hooter (24 V DC) compactable for fire alarm and burglar alarm system complete with all accessories including taking down old unsv hooter complete all as specified and directed. Make : - Safetech, Minimax, ECD

Supply installation. Testing and commissioning of 12 V 15Ah maintenance free battery including taking down old unsv battery complete all as specified and directed. Make:- Exide/Amron

S & F Fire Extinguisher, Clean agent type 2 Kg Capacity (IS: 15683) fixed on wall complete including taking down old unsv fire extinguisher complete all as specified and directed. Make : Monarch/Intime/Bharathi /Safety plus Engineering

S & F Fire Extinguisher, CO2 type 3.2 Kg capacity (IS: 15683) fixed on wall Complete including taking down old unsv fire extinguisher complete all as specified and directed. Make : Monarch/Intime/Bharathi /Safety plus Engineering

S & F Fire Extinguisher, CO2 type 4.5 Kg capacity (IS: 15683) fixed on wall Complete including taking down old unsv fire extinguisher complete all as specified and directed. Make : Monarch/Intime/Bharathi /Safety plus Engineering

S & F Fire Extinguisher, CO2 type 22.5 Kg capacity Complete with the trolly mounted including taking down old unsv fire extinguisher complete all as specified and directed. Make : Monarch/Intime/Bharathi /Safety plus Engineering

S & F Fire Extinguisher, Mechanical foam (AFFF) type, 9 Liters capacity (IS : 15683) Complete including taking down old unsv fire extinguisher complete all as specified and directed. Make : Monarch/Intime/Bharathi /Safety plus Engineering

S & F Fire Extinguisher, Dry Chemical Powder (ABC) type, 6 Kg capacity (IS : 15683) Complete including taking down old unsv fire extinguisher complete all as specified and directed. Make : Monarch/Intime/Bharathi /Safety plus Engineering

S & F Fire Extinguisher, Dry Chemical Powder type, 25 Kg capacity (IS : 10658) Complete including taking down old unsv fire extinguisher complete all as specified and directed.

S & F Ceiling hook (IS: 927 ) including taking down old unsv ceiling hooks complete all as specified and directed.

S & F fireman's Axe ( IS : 926 ) including taking down old unsv fireman's Axe complete all as specified and directed.

S & F of fire bucket with sand, round bottom 9 ltrs capacity with mounting bracket (18 SWG) complete including taking down old unsv fire bucket complete all as specified and directed. Note : A sum of Rs 29,807.00 towards sch of credit shall be deducted to arrive the contract sum

Atharva Enterprises

sapana enterprises