SPECIAL REPAIR TO BLDG NO T 198 ELECTRIC WIRING FITTING IN JCOS ORS LIVING BLDG SR TO SEWAGE PIT MANHOLE COVER SLAB DRAIN AND PROVN OF CERTAIN MINOR WORKS UNDER GE 865 EWS

Amount

Dismantling of wall and ceiling boards (fibre, pulp, insulation. etc) or insulation boards/slabs/blankets/ wooden panelling , any thickness, includinguding cover fillets all as specified and directed.

Dismantling timber scantling over 40Sqcm in section in any position ( frame work).

M&L for 2nd class soft wood clean sawn as in scantling fixed with nails. (timber framed and fixed)

S&F of wooden panelling on vertical surface of wall using following specifications complete all as specified and directed (i) S&F Iind class hard wooden gutties of size 25mmx25mmx200mm depth fixed in wall by making holes in brick wall and making good in cement mortar 1:3 (ii) S&F horizontal rummer IInd class soft wood (kali at 120c/c of sextional area exc 13 Sqm ans n.exc 25 sqm clean sawn treated with two coats of creoste oil mixed with good quality pesticide for antitermite treatment. (iii) S&F 1st classsoft wood (Deodar) boardig 12mm to 15mm thick as in wall panelling planed one side wrought and other side celan sawn and applying two coats of good quality varnish on plain surfaces of a coat of primer mixed with good quality pesticide for antitermite treatment on the other side and fixed with screws/nails on wooden runners. (iv) S&F 1st class soft wood (Deodar) decorative breading 40mm wide on top surface of wall panelling including two coats of vernish.

M&L for 7-9mm thick fine fissure teglar RH 99 Tringular and acoustic purpose of size 600x600x7mm thick fixed with dash through fastner bolt of approved quality with 04 Nos for per Sqm including necessaru cutting securing and making good, and including Anodised aluminium snap grid frame work for false ceiling including hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long complete all as specified and directed

Dismantling of floor,hearth or wall tiling includinguding cement mortar bedding but not backing and rubbish off the premises.

M & L 25mm thick PCC 1:2:4 type B-0 using 20 mm graded stone aggregate as in leveling course to floor complete all as specified and directed.

S&F Vitrified dark/double charged/ultracharged coloured flooring tiles 10mm thick (Square/ rectangular) of polished area of each tiles exceeding 0.42 Sqm but n exc 1.00 Sqm in floor etc, laid in floors with cement based adhesive , set an adjointed as per manufacture's instruction over and including 15mm thick screed bed or bedding layer in CM (1:6) complete

M&L for Non skid ceramic jointless/joint free coloured tiles 7 to 10mm thick (square/ rectangular) area of each tiles exceeding 0.11 sqm but not exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed with white as coloured cement to match over and including 15mm thick screed bed in cement mortor (1:6) complete all as specified and directed.

M&L for glazed ceramic colour tiles in vertical surfaces of size 450X350x7mm thick set and jointed in neat cement slurry and pointed with white or coloured cement to match over and including rendering 10 mm thick in cement mortor (1:4) on vertical surface as in backing coat all as specified and directed.

S&F powder coating for aluminium anodized door/partly paneled and partly glazed with 4.5mm thick plain glass sheet/wire mesh and 12mm particle board interior grade both side laminated and aluminium section weight not less than 0.55 kg/RM with self closing hydraulic door closer & floor srping etc with complete all fitting all as specified and directed.

Taking down chowckat or frame with shutters (without taking of shutters from the frame) exe 1.5 sqm each but n. exc 4 sqm each any type of door (wooden , aluminium & Steel etc)

Demolition of brickwork or stone boulder masonry, built in cement mortar including all quoins, arches, pillars, etc., but excluding ashlar facings, dressed stonework and precast concrete articles all as specified and as directed.

M&L Precast cement concrete 1:3:6 Type C1 (using 20mm graded stone aggregate ) block masonry with solid blocks exc 10cm in width and setting in CM 1:6

Taking down cement plaster on brick or stone walls, etc, incl raking out joints, hacking for key, scrubbing down with water, etc & prepare to receive new plaster complete all as specified and directed

M&L for 15mm thick rendering in CM 1:6 on fair faces of brick work, surfaces finished even and fair without using extra cement complete all as specified and directed

M&L for 15mm thick rendering in CM 1:4 on fair faces of brick work, surfaces finished even and fair without using extra cement complete all as specified and directed

Preparation of new plastered surface of wall and applying two coats of cement base paint over a coat of primer

Preparation of new plastered surface of wall and applying two coats of oil bound distemper over a coat of primer 2mm thick birla white care Putty on wall obtain smooth finish etc

Excavation in trenches n.exc 1.5M wide and n.exc 1.5M in depth for fdn, man holes etc in Hard/dense soil.

Excvation ovr area in Hard/dense soil not exceeding 3.0 mr deep including gettiong out complete all as specified and directed.

Returning filling in including spreading, watring and well ramming in layer n.exc 25cm each in loose/soft soil.

Removing excavated material n exc 50m and depositing where directed at a level n exc 1.5m above the starting point in soil.

Demolition and breaking up drain pipes upto 300 dia salt glazed ware, (SWG/AC/PVC/NP) or reinforced concrete) set in cement mortar including all fitting complete all as specified and directed.

M&L for Cement concerete bed to drain pipes incl packing under haunching against the sides of pipes after they are laid tested in 1:4: 8 type D-2 using 40 mm graded stone aggregate of bore of pipe 300mm.

S&F 300mm dia bore (inner dia) double wall corrugated HDPE pipe (SN-8) in any length including all fitting and jointing with eastomeric rubber link and cuppler/other jointing material laid in trenches are in floors all as sfd and directed.

M&L soakage well of 3.0 mtr internal dia at top and min 1.80 mtr dia at bottom having min 2.45 mtr height of 380mm thick random rubble uncoaoursed stone masonry wall in CM 1:6 with 150mm thick PCC 1:4:8 type D2(using 40mm graded crushed stone aggregate ) below stone masonry at bottom and RCC slab using Design Mix M-25 with reinforcement 10mm dia bars @ 150mm C/C bothways cranked at 1/4 th of span including arrangement for manhole opening and manhole cover, inlet for 100/150mm dia pipe and rest all as specified as per Drg No CESZ/TD-1078/2011 sheet 1/1. Note : The rate includes excavation in hard/dense soil and construction of soakage well as per drawing , connection of inlet pipe , 100mm dia PVC vent pipe with cowl, returning , filling and removing of surplus soil to a distance exc 50 mtr but n.exc 100 mtr from site. For any disputed issue regarding drawing decision, of Engr-in-Charge shall be final and binding for execution.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15cm thickness (below and above ground level) and removing the unserviceable materials to a distance not exceeding 100m all as specified and as directed.

M&L for 100mm thick PCC 1:4:8 type D2 using 40mm graded crushed stone aggregate as in sub sub base complete all as specified and directed

M&L for 100mm thick PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in floor complete all as specified and directed

Supply and fixed in repair One piece Vitreous china wash down water closet (Pedestal Pattern) size 710x390x790mm 'white' with soft close seat cover & twin flush fittings, toilet paper holder, health faucet, PVC connection, angular stop cock (valve) (2 Nos) with flange etc all as specified in Particular specifications. Note : Vitreous china wash down water closet (Pedestal Pattern) cat Part No. CRUISER S1013137S TRAP 300MM trap 250mm of 'Cera' or equivalent model of Jaguar/ Hindware

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 120mm (minimum) wide with chromium plated brass bracket guard and railing 600mm long complete.

S&F in repair Chromium plated brass soap dish (oval shape) to walls (size not less than 125mm long) complete all as specified and directed

S&F in repair Chromium plated brass paper holder Note :- Cat part No- F5004110 of carrier equivalent of Jaguar/ Hindware.

S&F in repair (cat part No F840012 HINDWARE/JAQUAR/ CERA) double bar (Hollow) towel rail 600mm long and 20mm dia of CP fixed with and including Chromium plated brass screws and wooden/plastic cleats

Taking up or down 25 mm or 32mm dia steel tubing/16mm 3 Layer PP-R Polypropylene rndom copolymer) and connections including cleaning for refixing or removal to store complete all as specified and directed.

Supply & Fixed 25mm 3 Layer PP-R Polypropylene rndom copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc with all fitting and fixed to walls, complete all as specified and directed.

S&F PP-R 25mm Gate valve (brass insert) as per requirment of the site

S&F 15 mm Bib tap long body with wall flange fancy type chromium plated brass screwd for iron pipe with capstain head complete all as specified and directed Note : Bib cock Cat part No- F1012151, 'Cera' or equivalent model of make Jaguar/ Hindware.

S&F Two way Angle cock , fancy type, chromium plated with long shank and cup (two way Angle valve type) cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of bore of pipe 15mm complete all as specified and as directed. Note : Two way angle cock Cat part No-F200211 GARNET QUARTER TURN FITTING 2 WAY ANGLE COCK , 'Cera' or equivalent model of make Jaquar/ Hindware.

S&F grating doom 100mm dia of CP (Minimum weight 60 Gms) complete all as specified and directed

S&F in repair PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and as directed.

S &F in repairs health faucet, brass, chromium plated with pipe length 1000mm, washers, connections etc. Cat part No F160002 of Hindware JAQUAR/ CERA or Equivalent complete all as specified and as directed.

S&F in Repair Vitreous China Urinal full stall type white (excluding flushing cistern flush pipe and wast pipe) Vitreous China Urinals bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement fixing automatic flushing cistern with brackets, flush pipe grating and union for discharge pipe complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not other wise specifically provided for and removing debris outside the MD land.

M&L for providing precast reinforced cement concrete type A1, 1:1.5:3 using 20mm graded aggregate as in landings, cover slabs (for man holes etc) and similar articles with plain faces and setting in cement mortar 1:6 complete with joints to match including use of necessary formwork . Note : S&F reinforcement shall be measured and paid separately.

S&F TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia

S&F TMT bars 6 to 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia

Supply only Integral waterproofing compound complete all as specified

Material & Labour 75mm thick PCC 1:3:6 type C1 (using 20mm graded stone aggregate) as in plinth protection and finished concrete surface even and smooth without using extra cement complete all as specified and as directed.

M&L for 75mm thick PCC 1:4:8 type D-2, using 40mm graded crushed stone aggregate as in sub base .

Demolition and breaking up 150mm dia drain pipes (Salt glazed ware, AC or reinforced concrete) set in cement mortar including the pipe inserted in Man holes walls etc. for undermentioned drain pipes, including removal of rubbish outside MD land :-

All as per above Item Ser No 53.00 but 200mm dia

M&L for providing cement concrete 1:3:6 type C-2 bed to 150mm bore of drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for:-

All as per above Item Ser No 55.00 but 200mm dia

S&F, 150mm dia bore (inner dia) double wall corrugated HDPE Pipe (SN-8) in any length including all fittings and jointing with eastomeric rubber link and cuppler /other jointing materials laid in trenches are in floors all as sfd and directed by Engr-in-charge.

S&F, 200mm dia bore (inner dia) double wall corrugated HDPE Pipe (SN-8) in any length including all fittings and jointing with eastomeric rubber link and cuppler /other jointing materials laid in trenches are in floors all as sfd and directed by Engr-in-charge.

Cutting in to existing manholes for forming new drains and making good to pipe and making good to pipe and rendering ,cutting out existing benching in cement conc 1:2:4 type B1(in 1/2 or 3/4 round in section)and reforming benching as reqd for 150mm bore pipe.

M&L for cleaning of man holes n.exc 1.5m deep and removing sludge/waste material to distance n.exc 50m and burying in pits and refilling the same complete all as spfd and directed by Engg-in charge .NOTE: The cost for excavation and earth work for pits is deemed to be included in the unit rate

All as per above item NO 60.00 but exceeding 1.50m depth

Dismantling of 75 / 110mm bore cast iron ,PVC or reinforced concrete pipes jointed in cement mortar and taking out of trenches if reqd of any dia

S&f 75 mm bore PVC (SWR) pipe single socketed , in any length with rubber joints laid in trenches or in floors.

S&f 75mm bore PVC (SWR) pipe bends any radius

S&F 75mm bore PVC (SWR) junction single, (Single T) equal or unequal

M&L for 7mm thick non skid coloured ceramic tiles (area of each tile exc 0.06 and nexc 0.11sqm) etc set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments.

Demolition of cement concrete (unreinforced) of any description and in any position not other wise specifically provided for and removing debris outside the MD land.

M & L PCC 1:3:6 type C2 using 40mm graded aggregate in surface channels and drain, complete all as specified and as directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement incl forms, moulds, mitred/stopped ends etc.

M&L for Preparing newly plastered surfaces of walls including Chalk whiting, on plastered surfaces and applying two coats of distemper oil emulsion, complete all as specified and as directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

Prepration of new plaster surface of wall and applying two coat of cement base paint over a coat of primer including balance area complete removal.

S&F Powder coated (minimum thickness of powder coating 50 micron) anodised aluminium frames for door, windows, ventilators with one or more rebates including joining cleat for fixinf etc complete all as specified.

S&F Powder coated (minimum thickness of powder coating 50 micron) anodised aluminium door shutters, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading screws etc. complete all as specified and directed by Engr-in-Charge.

Supply and fixing Sheet glass 5.5 mm thick, exc 0.5 sqm in each pane complete all as specified and as directed. Make of Glass : Modi Guard/Saint Gobin/Swastik

S&F Powder coated (minimum thickness of powder coating 50 micron) anodised aluminium window and ventilator shutters, side hung/top hung/partitions type without sash,aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading screws, anodised aluminium fittings such as peg stays 150mm long (1 Nos) hinges type B-21 100mm long (2 Nos) suitable handle (1 Nos) etc. complete all as specified and directed By Engr-in-Charge.

S&F in repair aluminum door closer ( aluminum extruded section) hydraullically regulated , designation No 3 , universal type , suitable for door shutters of 851mm to 1000 in width and of weight 61 to 80 kg complete all as specified and directed By Engr-in-Charge.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials complete.

M&L for Point wiring for one light point or fan point or bell point controlled by one switch with PVC insulated FRLS copper conductor stranded cable of size 1.5 sqmm and including PVC casing/caping terminated in pressed steel terminal boxes for fixing and 1.5 sqmm PVC insulated copper wire as earth wire connected to earth wire connected to earth dolly and 3.00mm thick plastic lamiated sheet cover complete.

All as per item No 79.00 here -in-before but 1.5 sqmm for one 3 pin 5 Amps socket outlet including 1.5 sqmm insulated copper wire as earth wire to the same earth dolly on same board.

All as per item No. 79.00 here -in-before but 1.5 sqmm for one 3 pin 5 Amps socket outlet independent including 1.5 sqmm insulated copper wire as earth wire to the same earth dolly.

M&L for point wiring for 3pin 15 Amps socket outlet independent with FRLS copper conductor cable PVC insulated multistrand 2.5 Sqmm with 2 .5 sqmm PVC copper conductor as earth wire connected to earth dolly and including PVC casing/caping with sunk cast iron.

S&F switch socket combination outlet , 2/3pin 5 Amps complete all as specified and directed.

S&F socket outlet 3 pin 5Amps flush type complete.

S&F switch socket combination 2in 1, 3 pin 5 and 15 Amps piano flush type single pole ISI marked complete.

S&F switch piano flush type single pole one way 5 Amps ISI marked complete.

S&F ceiling rose surface bakelite 65 x 50 two to three terminal all as specified and directed.

M&L for lamp holder PVC/Polycor bonate type insulated body with back plate suitable for batten /angle fittings as specified and directed.

Supply and fixing surface/wall mounted LED fittings with LED tube 18 watts, 6000Kcapacity decorative ultra slim round profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient 4 feet long type bracket including neccessary conection prewired and making connection with 3 core copper flexible cable of appropriate size from ceilling rose/PVC connector to light fittings Make: Havells, Cat No: LHEXBLP7PN1W018 ,or equivalent in Bajaj/ Philips/ Wipro.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

S&F of MCB DB TPN 4Way double door 415Volt 50Hz with complete accessories.

S&F of MCB DB SPN Regal Gray 12Way double door 240Volt 50Hz with complete accessories. Make : Havells / ABB/Schenider

S&F in replacement of MCB DB SPN 8Way double door 240Volt 50Hz with complete accessories.

S&F MCB TPN 63Amps 'C' series complete all specified and directed by Engr-In-Charge. Make : Havells/ABB/ C&S

S&F for MCB SPN 32 Amps 'C' series complete all specified and directed by Engr-In-Charge. Make : Havells/ABB/ Indoasian/ C&S

S&F for MCB SP 5-32Amps 'C' series complete all specified and directed by Engr-In-Charge. Make : Havells/ABB/ Indoasian/ C&S

S&F for sub main wiring with 2 runs of FRLS PVC insulated multistrand, copper conductor cable of size 6 Sqmm along with one run of 6 sqmm PVC insulated cable 1100 volts multi stranded copper conductor as earth wire in and including PVC casing caping incl taking down old one complete incl taking down old one complete all as specified and directed.

Supply, fixing and testing of Fire alarm control panel complying with BS EN 54 Single loop panel of capacity from 4 detectors & 4 modules upto 200 detector and modules (per each loop) complete all as specified and directed.

Supply, fixing and testing of Addressable type multisensor detector with heat and smoke combination complete all as specified and directed.

Supply, fixing and testing of Addressable manual call point resettable type complete all as specified and directed.

S&F 1.5 Sqmm 2 core flexible FRLS copper cables through rigid PVC conduit including wall mounting with saddles, clamps, screws, junction boxes all complete all as specified and directed.

Supply, fixing and testing of Fire Alarm Sounders / Sirens Electronic type horizontal single/two stage continous normal operation for atleast 50 minutes with sound level 65 DB to 120 DB measured at 1.5 Mtr with sound output variation of + 5 DB 1000 mtrs range complete all as specified and directed.

S&F in replacement 2'x2' Recess mounting low depth White LED Luminaires white powder coated CRCA sheet housing LEDs front frame with translucent cover fixed to the housing fixed in front frame 36w LED extruded alluminium heat sink projected in false ceiling . Make-BAJAJ /Philips/Wipro/Crompton/Syska)

S&F in replacement of old U/S LED Mirror light fitting 9/10 watt 230 volts box type , with standard specification etc warm white colour complete confirming to Crompton cat part No- LCL-07-CDL or eqvt in Philips/Wipro/Bajaj/Havells.

S&F in replacement of old U/S Lamp LED 7 Watt, 230 volts 50 Hz AC complete all as specified. Make: Bajaj/Crompton/Havells/Wipro

Supply and fix in replacement of exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 150 mm sweep all as specified and directed.

S&F in replacement of Old UNSV sheet metal enclosure SPN for DBs with 200 Amps bus bar of 12 way 240 volts with blank plate Double Door all as directed by Engr-in-Charge. Make :Legrand or equivalent in L&T

S&F in replacement of old MCB SPN,C- curve, 230 volt 40 amp 10KA

Earthing complete with galvanised iron earth plate electrode 600x600x6mm buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of earth plate not less than 1.5mtr below normal ground level, connected using galvanised iron strip 25×4mm as earthing leadby means of bolts, nuts, check nuts and washers of galvanized iron or steel complete with 40mm dia GI light grade protection pipe, 20mm dia GI medium grade watering pipe with funnel including charcoal, dust, salt, PCC M-15, type B-1 in pit with precast RCC M-15(1:2:4), type B-1 (using 20mm graded crushed stone aggregates) in cover reinforced with XPM not less than 4.0 Kg per Sqm, test point etc. all as shown in electric plate No-3 of SSR Part-I (2009), complete with necessary earth work in any type of soil, removal to a distance not exceeding 50mtr, including testing on completion, complete all as specified and as directed by Engineer-In-Charge. Note: Earth pit chamber and RCC pit cover shall be painted with two coats of red synthetic enamel paint over one coat of primer including preparing of surfaces.

M/S BALI CONSTRUCTIONS

bharat construction

M/S RIGDOL CONSTRUCTION

M/S Praveen Kumar and Sons