GE/BAS-50/2021-22 SPECIAL REPAIR TO BLDG NO T-14S (STORAGE ACCN FOR FURNITURE) AT MES COMPLEX AT BASOLI GRN UNDER GE BASOLI AND JANGLOT

Amount

Demolition of brickwork or stone boulder masonary built in cement mortar including all quoins, arches, pillars etc cement complete all as specified and as directed.

Brickwork with sub class ‘B’ (old size) bricks, straight or curved on plan exceeding 6 metre mean radius built in cement sand mortar 1:6 complete all as specified and as directed.

-Ditto- all as per Srl item No. 2 here-in-before, but except bricks.

Taking down cement plaster of any description including raking out joints, hackisng for key, scrubbing down with water etc cement complete all as specified and as directed.

M&L for rendering 10 mm thick in cement and sand mortar 1:6 on fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15mm thick in cement mortar 1:4 finished fair and even without using extra cement complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil emulsion distember complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of cement base paint complete all as specified and as directed.

M & L Preparation of new surface of wooden and applying two coat of synthtic enamel paint over a coat of pink primer all as specified and directed .

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level ) complete all as specified and as directed.

M&L for 100 mm thick PCC 1:2:4 type B-2, using 40 mm graded stone aggregate,as in subbase cement complete all as specified and as directed.

M&L for 50 mm thick Sand filling/cushioning as in floor, foundation including watering and consolidation complete all as specified and directed.

M&L machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658- 2006 0f 60mm thickness with grey cement and pigment, M-35 grade complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-1, using 20 mm graded stone aggregate, including finishing surface of concrete topping even and rough as in levelling cousre cement complete all as specified and as directed.

M&L for 20-25 mm thick machine cut kota stone slab as in flooring, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 20mm thick screed bed in cement and sand mortar 1:6 complete all as specified and as directed.

M&L for 20-25 mm thick machine cut kota stone slab as in skirting/dado jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 10mm thick screed bed in cement and sand mortar 1:4 complete all as specified and as directed.

Dismantling of any type of roof covering (Plain, corrugated, semi-corrugated, steel etc.) sheet , complete all as specified and as directed.

S&F Pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of asbestos cement (corrugated, semi corrugated etc) sheets in roof coverings, complete all as specified and as directed.

Ditto all as per item No 18 here-in-above, but plain sheets

Dismantling wrough iron or mild steel work of any descrfiption not otherwise provided for, complete all as specified and as directed.

S & F Roof trusses (framed), trussed, purlins, crane gantries, rail and heavy brackets framing (Beams, tee, angle, channel or flat section) including distance pieces including two coat of synthetic enamel steel paint over a coat of red oxide complete all as specified and as directed.

S & F framed work such as grills , gratings etc framed guard bars , iron door/gate of any type and similar work including iron hold fast , sliding door bolt for locking arrangement and etc including two coat of synthtic enamel paint over a coat of red oxide complete all as specified and as directed.

S&F Steel windows/ventilator (Box type) factory made glass/glazed shutter,and including shutter for wire mess (glass panes and wire mesh shall be measured and paid separately) of size 79mmx39mm,16 gauge rectangular tubular frame with side hung shutter with glazing bars 12x3mm flat iron incl box type hinges with steel handle and steel peg stay dovetailed or welded incl 2 Nos tower bolts 100mm long and 10mm square bar grills including two coat of synthetic enamel paint over a coat of red oxide complete all as specified.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size exc 1.5 Sqm but n exc 4.0 Sqm each and removing from site complete all as specified.

S&F Pressed steel frame for doors of size 105 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc including including two coat of synthetic enamel paint on steel surface over a coat of red oxide complete all as specified and as directed.

S&F Pressed steel frame for doors of size 125 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc including including two coat of synthetic enamel paint on steel surface over a coat of red oxide complete all as specified and as directed.

M&L for PCC 1:3:6 type C-0 using 12.5 mm graded stone aggregate as in filling of pressed steel frame complete all as specified and as directed.

M&L PCC 1:3:6 type C-1 using 20mm graded stone aggregate for hold fast blocks, including necessary form work for rough finished surfaces etc complete all as specified and as directed.

S&F 35mm thick, IInd class hard wood plain, framed, panelled factory made shutters (two panel) with lock rail and panel of 12mm veneered particle board with commercial veneering on both faces. The size of rails and styles as per IS-1003 (Part-I) kiln seasoned and chemically pressure treated complete all as specified.

S&F 35 mm thick, 2nd class soft wood , glazed & skeleton factory made shutters, open rebated & prepared to receive glass, gauze etc. (without sash-bars), edges of framing plain, chamfered or rounded fitted with cut and metred beads for securing glass etc., sizes of members of shutters as specified in SSR Part-I, Section-8, clause 8.20(a) complete all as specified.

S&F butt hinges, 100 mm long medium weight, cold rolled mild steel, ISI marked complete all as specified and as directed.

S&F 250mm long aluminium alloy anodised sliding door bolt with hasp staple, bolt type, and fixing clips of sheet, cast or extruded sections & fixing bolts and sliding bolts of extruded section or cast aluminium alloy, ISI marked complete all as specified.

S&F 200mm long, aluminium anodised, barrel tower bolts, of extruded section ISI marked complete all as specified and as directed.

S&F Aluminium handles cast type anodised of size 150mm long ISI marked complete all as specified and as directed.

S&F Door closer of aluminium (Die cast body), hydraulically regulated, designation No 2, universal type, suitable for door shutters of weight between 36 to 60 Kg, ISI marked, complete all as specified and as directed.

S&F 300 mm size mild steel ordinary rat tail rod pattern springs including roller and roller plate, ISI marked complete all as specified and as directed.

S&F 3 mm thick sheet glass, ordinary quality and glazing with oil putty/wooden beads in square not exceeding 0.5 square metre in each pane complete all as specified and as directed.

S&F Galvanized mild steel wire-cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified.

M&L 75mm thick PCC (1:3:6) type C-2 using 20mm graded stone aggregate as in plinth protection laid in bays complete including finishing the surface of concrete topping even & fair, without using extra cement complete all as specified and as directed.

M&L PCC 1:2:4, type B-1 using 20 mm graded crushed stone aggregates as in copings, bed plates, kerbs, ramps etc, water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed.

M & L for PCC type B0 1 :2:4 (12.5 mm graded aggregate ) in roof ,kerbs,or mud stops,, rounded or chamfered on edges complete all as specified and as directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.

M&L Point wiring with 1.5 Sqmm FRLS, PVC insulated and unsheathed multi stranded flexible copper conductor cable in and incl rigid PVC conduit concealed medium grade with PVC terminal sunk boxes with suitable thickness plastic laminated sheet cover 3mm thick of adequate size for one light or one fan controlled by one switch incl 1.5 Sqmm FRLS, PVC insulated and unsheathed multi stranded flexible copper conductor cable as earth wire(green colour) to common earth dolly complete all as specified and directed. NOTE :- a) Rate for cutting chases for conduits and sinking for boxes and making good to wall, floors deemed to be included in each point etc (b) On RCC roof ceiling PVC conduit shall be provided on surfaces for any necessary point with proper fixing clips and no extra cost shall be paid for the job etc all as directed.

All as per item No 43 above but for one 3 pin 5 Amp socket outlet on independent board.

All as per item No 43 above but for one 3 pin 5 Amp socket outlet on same board.

Point wiring with 2.5 sqmm FRLS, PVC insulated and unsheathed multi stranded flexible copper conductor cable drawn in and including rigid PVC concealed conduit medium grade of suitable size with sunk cast iron/pressed steel terminal boxes(sheet not less than 1.6mm thick) of adequate size with suitable thickness plastic laminated sheet cover 3mm thick for one 3 pin socket outlet 15 Amp on independent board including continuous 2.5 sqmm FRLS,PVC insulated and unsheathed copper conductor cable (multistranded) as earth wire to common earth dolly, complete all as specified. .

Supplying & Fixing switch piano flush button single pole one way 5 amps 230 volts, complete all as specified and directed

Supplying & Fixing Switch socket combination 2 in 1, 5 pin, 5 Amp flush type. Make :-C&S/Havells/polycab/Plaza

Supplying & Fixing socket outlet 5 amps 5 pin flush type, 230 volts, complete all as specified and directed by Engr-in-Charge.

Supplying & Fixing socket out let, 6 pin, 5 and 15 amps multi purpose 2 in 1 flush type, 230 volts, complete all as specified and directed by Engr-in-Charge. Make :-C&S/Havells/polycab/Plaza

S&F ceiling rose surface bakelite two to three terminal isolated body fixed on PVC round block complete all as specified.

Supplying & Fixing switch piano flush button single pole one way 5 amps 230 volts, complete all as specified and directed

Supplying & Fixing socket outlet 5 amps 5 pin flush type, 230 volts, complete all as specified and directed.

S&F ceiling rose surface bakelite two to three terminal isolated body fixed on PVC round block complete all as specified.

S&F in replacement LED tube light fitting 1x16w,230v Industrial box tpye, including LED tube rod with polycarbonate diffuser , 4 feet fitting fixtures, complete with all accessories internally pre-wired and including connecting up with three core twisted flexible copper conductor cable with suitable size. complete all as specified

Suppy and fixing LED luminaire 600mm x 600mm 35/36 watt, 230 Volt AC ressed type with high efficeincy PMMA diffuser soft glare free light complete driver, holders & LED lamp suitable for roof ceiling including connecting up with dirver three core flexible copper coductor case of suitable size complete.

S&F Ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep, Min air delivery 210 CFM with service valu 6.00 BEE. Five Star rated with brushless direct current motor (BLDC) all as specified and directed.

S&F in replacmenet sheet metal powder coated vertical double door single pole and neutral (SPN) distribution board for MCB provision 230 Volts 50 Hz AC supply for 08 Way fitted with copper bus bar rated 200 Amps, neutral link, earth bar complete all as specified.

S&F MCB SPN 40 Amps with 10 KA Breakiing capacity of C series in distribution boards all as specified and dirrected.

S&F MCB SP 6 Amps with 10 KA Breakiing capacity of C series in distribution boards all as specified and dirrected.

M&L for Earthing complete with galvanized steel earth plate electrode 600x600x6mm thick buried directly in ground (Earth pit not less than 2.25 Metre deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level, connected to galvanized earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No.5 of SSR Part-I (2009) including filling of charcoal dust , common salt all around Earth plate up to 150mm, 20mm bore GI medium grade watering pipe, 15 mm bore light grade earth lead protection pipe up to main board, funnel with wire mesh, 40mm thick RCC 1:2:4 type B-1 using 20 mm graded crushed stone aggregate reinforced with suitable handle and angle iron frame and necessary excavation and earth work in any type of soil etc. complete all as specified and as directed including testing on completion. (Note: The rate quoted include cost of min 7.5 metre earthing wire .)

Excavation in trenches n.exc 1.5 mtr wide and n.exc 1.5mtr in depth for foundation of pole and laying of UG cable and getting out in any type of soil complete all as specified and directed.

Returning filling in and including spreading, levelling, watering and well ramming in layers not exceeding 25cm completed all as specified and directed.

Removing excavated material n.exc 50m and depositing where directed at a level n.exc 1.5M above the starting point complete all as directed.

Supply and Laying in trenches or passing through pipe or fixing to pole/wall UG cable XLPE 70 sqmm 3.5 core, PVC insulated,armoured heavy duty electric cable with aluminum conductor,1100 Volts grade,cross section area are as under of Make- polycab/KEI/RPG

Supply and Laying in trenches or passing through pipe or fixing to pole/wall UG cable XLPE 25 sqmm 3.5 core, PVC insulated,armoured heavy duty electric cable with aluminum conductor,1100 Volts grade,cross section area are as under of Make- polycab/KEI/RPG

S&F DWC high density polyethelene pipes in replacement having 63/50outer dia mm, inner as per site requirement having corrugation on the wall and plain surface on the inner wall conforming to IS: 14930(Part I & II) for protection of underground cable laid along pole/along wall/in PCC on GL/roof and including all fittings as required at site including aking down the old unserviceable complete all as specified and directed. Make -Trupati /Equivalent

S&F, Fabrication of double and outdoor type incorporated with Feeder pillar panel having with aluminium busbar capacity 100 amps insulatted with RYB& black PVC insulattion tape suitable for 415 volts 3 phase 4 wire system 50 c/s fixed on SMC/DMC in step way complete with dust and vermin proof provisions made of CRCA MS sheet not less than 3.00 mm thick also having provision for incoming/outgoing COS/ cables, 02 Nos earth terminal point complete with 10mm bolt, 02 nos nuts and 02 Nos Washers3mm thick complete earth . The panel body must be painted with powder coated paint after the complete 7 tanks dip process of to remove all impurties from the panel sheet, all the door must be fixed with detach able pin type hinges,steel door locking system, bus bar shall be through aluminium strip properly insulated fixed on SMC/DMC insulators. Panel body shall be fixed on iron angle frame of size 40x40x5mm 40 cm grouted in 1:2:4 type 1 PCC 20 mm graded and 40 cm above the ground level duly painted with two coat of synthetic enammelled black paint over a coat of red oxide primer all as specified and directed. Following accessories in & including shall be part of feeder piller box :- (ii) MCCB 2000 amps Ics=100% Icu 25 KA rating TP 415 volts 01 No(incoming) (iii) MCCB 63 Amps Ics=100% Icu 25 KA TP rating 415 volts 06 Nos (outgoing) (vii) RYB LED Indicator lamp- 03 Nos

M&L for earthing complete with galvanized steel earth plate electrode 600x600x6mm thick buried in ground vertical to a depth not less than 2.25 mtrs deep below ground level with top edge of plate not less than 1.5 mtr below normal ground level connected to GI strip of size 32 X 6 mm and 40 mm dia bore 7.5 mtr long light grade GI protection pipe for earth strip and GI watering pipe 20 mm dia medium grade from the top edge of earth plate fixed with deep cut on one end of pipe and fix from earth plate up to one feet above ground level of other end and plugged watering pipe at top with RCC 1:2:4 type B-1 using 20 mm graded crushed stone aggregate reinforced with suitable handle and angle iron frame and necessary excavation and earth work in any type of soil etc. complete all as specified and as directed including testing on completion. (Note: The rate quoted include cost of min 7.5 metre earthing wire .)

Om Sai Ram Builders

Ms Narinder Kumar Sehgal

M/S YASH PAUL RAINA AND CO

R K Builders

GANDOTRA CONSTRUCTION CO

Ms International Engineers

M/S RUDHRAKSH TRADING CO

Substantial Const. Co.

Ms Dalip Kumar and Co.