Construction of PHC with Residences at village Sinsar (Jind) (Pdg. Street Light and DG Set only). Recall

Amount

HSR Items

20.89 Designing, Supply & Erection of DG Set of capacity given below with noise controlled devices, acoustic rating, testing and commissioning of diesel generating set, radiator cooled 3 phase 4 wire 50 cycles 415 + (-) 1% volts AC alternator coupled directly through a set of flexible coupling on a common MS fabricated base frame with diesel engine complete with suitable size incoming cable from generator to change over /AMF panel, making 2nd incoming cable connection from transformer, outgoing cable connection from changeover / standard panel, making second incoming cable connection from transformer, outgoing cable connection from changeover / STD panel to incomer of motor starter panel, fenced enclosure with platform for DG set complete as per following detailed scope and specifications and directions of Engineer-in-Charge. The rating should be at 1500 RPM

Diesel Engine

Alternator

Battery 24 V

Base Plate

suitable Sqmm suitable core copper cable upto 40 meters

Tools, standard panel

Metering set 415 VAC-1 set (Amp. Meter, Volt Meter, ASS, VSS, Phase Indicator, Control Fuse, Frequency Meter, CT's)

Metering set 60/5A/110V (Amp. Meter, Volt Meter)

Overload protection for DC-1 No.

Battery Charger 24 V DC

Copper Bus Bar of Suitable Size

KWH meter 96 Sqmm size

Startig fuse button and key switch on / off

Indicating lamps for low lubricated oil pressure, high coolant temperature, set running, load on, DC control and other required accessories complete in all respect to the satisfaction of Engineer-in-Charge

20.89.3 25 KVA DG Set (Make as per approved list)

23.5 Coppper Wiring in existing PVC / MS Conduit Pipe Surface / Recessed

23.5.6 Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated copper conductor cable 1100 volts grade in existing MS / PVC conduit etc. as required

23.5.6.1 1 Run of Size 1.50 sqmm (1/1.40mm).

23.22 MCCB, Distribution Boards, MCB's, RCCB's, Change Over etc.

23.22.1 Supply and erection of moulded case circuit breakers single pole / 4 pole on existing wall /pedestal/Panel including bonding to earth and making necessary connections required to complete the job in all respect upto the entire satisfation of the Engineer-in-Charge of the work.

23.22.1.3 Triple Pole MCCB 16 Amp. to 100 Amp., 25 Ka

23.22.2 Mmccb Enclosure made of Sheet Steel suitable for mounting MCCB of following ratings

23.22.2.1 MCCB up to 125 A FP

23.22.5 Supply and erection of miniature circuit breaker 240/415 V in the existing distribution board including making necessary connections.

23.22.5.1 6 Amp. to 32 Amp. Single Pole

23.27 Supply and erection of Godrej Almirah typeM.S. pedestal mm angle iron frame with 3.00 mm thick M.S. sheet covering including shutters with made of 50 mm x 50 mm x 6 suitable hinges and locking arrangement with Godrej type handle including round bars The top covering should have downward overhang of 75 mm on all sides of pedestal , having two sets of water proof ventilation holes of Suitable size on the sides, at top and bottom, each set containing four Nos, holes to discharge the heat produced by the current. The shutters fixed with rubber gasket of superior quality and of suitable size to make it water proof. The pedestal duly painted both inside and outside with two coats of approved paint and primary coat and its legs are embeded upto the entire depth in 1:2:4 cement concrete block, projected 75 mm all around the pedestal and and 200 mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer in-charge of the work

23.27.1 M.S. pedestal of size 600 mm wide 750 mm high 300 mm deep and bottom totally open, duly embeded in 1:24 cement concrete block of size 750 mm x 450 mm x 200 mm above ground level, having a base of size 900 mm x 600 mm x 250 mm below ground leve

24.1 Earthing and Lightening Arrestor

24.1.1 Earthing with GI earth pipe 4.5 m long and 40 mm dia with masonry enclosure on the top etc. (but without charcoal or coke and salt) as required .

24.1.2 Extra for using salt and charcoal / coke for pipe earth electrode as required.

24.1.12 Supplying and laying of 6 S.W.G. G.I. wire at 0.50 meter below ground level from earth electrode including thimbles, soldering etc. as required .

24.5 Miscellaneous Items

24.5.2 Supply and erection of mark double walled corrugated (DWC) HDPE pipe 10 Kg./Cm2, laid 0.75 Mtr. below ground level including diging and refilling of earth including cost of sutiable size socket/cuppler for HDPE pipe including the cost of labour and material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of the work.

24.5.2.3 DWC /HDPE pipe 63/50 mm outer dia / inner dia.

24.4 Street Light

24.4.8 Supply & Erection of Hot Dip Galvanized octagonal pole of 3 mm thickness, with base plate including cost of nut and bolts, earthing studs, Integral Cable termination arrangement 5 mm thick bakelite base plate on suitable welded MS/GI bracket 32A four way connector 2 No. 10 A Sp MCB, end cover and all accessories as supplied by the manufacturer including providing RCC foundation of M 25 grade (1 Cement:1Stone aggregate:2Coarse sand) i/c excavation, steel reinforcement (Fe 500) @ 80 Kg./Cum of concrete contents, concrete cover 50 mm, anchor bolts etc. over a bed of PCC 1:5:10 of required dimensions for octagonal poles of various heights as per follwoing specification complete in all respects and as per directions of Engineer-in-Charge Make: VIPIN ST/GE/PHILLIPS

24.4.8.5 7 Mtr. Long pole with top dia 75 mm and botom dia 150 mm with base plate of size 300 x 300 x 20mm.

24.4.15 B.S.E.N. 10025 High Masts

24.4.16 Supply and erection of weather proof M.S. box of size 20 cm x 15 cm x 10 cm. covered with 3.00 mm thick M.S. sheet hinged cover, locking arrangement, housed in wall, including the cost of 1 no. 16 amp. 415 volts SP MCB and 2 nos. 63 amp. 415 volts neutral links fixed on hard wood board/10 mm Bakellite sheet in the M.S. box including painting and necessary connections

24.7 RCC Foundations for DG Set

Providing RCC foundation of M 20 grade (1 Cement: 1.5 Stone aggregate: 3 Coarse sand) i/c excavation, steel reinforcement (Fe 500) @ 50 Kg/cum of concerete contents, concrete cover 50 mm, over a bed of 75 mm thick PCC 1:5:10 of required dimensions as per OEM recommendations to provide levelled surface for placement of the DG set complete in all respect and as per directions of Engineer-in-Charge. Note: As size and dynamic load of DG sets vary from manufacturer to manufacturer, item of DG set foundation have been included on the basis of cubic contents of RCC)

24.7.1 30 to 40 KVA DG set

M.R. Items

N.S - 1 Supply and Erection of LED street light lumanaries of Havells make Endura CITYLINER NEOSL 70W LED or its equivalent model and specifications of Crompton/Wipro/Phillips/Bajaj make with die cast housing, toughened glass IP66 with all acessories as supplied by the manufacturer with all labour and material required to complete the job in all respect upto the Entire Satisfaction of the Engineer-in-Charge of the work.

N.S - 2 Supply & Erection of Single/double arm bracket made of 40mm dia G l pipe B class lSl 1.25mtr. Long with coller pipe (Gl) 75mm dia 60 cm Long top covered with ornamental cap duly welded painted 2 coats of aluminum paints on bracket and golden paint of ornamental cap including the cost of labour and petty material etc. complete in all respect up to the entire satisfaction of Engineer-in charge of the work.

i) Single Arm Bracket

N.S - 3 Supply & Erection of LED flood light fitting of Havels make JETA IRI SFL 100W LED or its equivalent make of Crompton/Wipro/Phillips/Bajaj make with pressure die cast alluminium housing, reflector and enclosed with toughened glass with all accessories as supplied by the manufacturer complete in all respect upto the entire satisfaction of Engineer-in-Charge of the work.

N.S - 4 S/E of underground cable loose in existing pipe or trenches complete in all respect upto the entire satisfation of Engineer-in-Charge of the work.

i) 10 Sqmm 4 Core Cable (Armd.)

ii) 16 Sqmm 4 Core Cable (Armd.)

iii) 50 Sqmm 3.5 Core Cable (Armd.)

N.S - 5 Supply and erection of MS Saddle and clamps duly galvanised , on wall / RCC parapit for fixing underground cable at a distance of 0.60 metre center to center fixed by means of rawl plug including the cost of all labour and material required to complete the job in all respect and upto entire satisfaction of the Engineer-in-charge of work. (Based on Old HSR 31.48)

N.S - 6 Supply and erection of MS stand made of 50mmx50mmx6mm angle iron frame and 150cm long, 30cm wide with MS sheet covering size 30cmx30cm 3.15mm thick fixed on the top of board & legs duly embedded in 1:2:4 cement concrete block 30cm below ground level including the cost of cement sand, welding, painting & fabrication charges etc. up to the entire satisfaction of Engineer - in - charge of the work. (Based on Old HSR 31.51)

M/S PANJETA ELECTRICALS