Construciton of Zonal Head Quarter building of ACB at Peer Bagh Srinagar

Amount

A-CIVIL Work:- Boring, providing and installing bored cast-in-situ reinforced cement concrete pile of specified diameter and length below the pile cap in M-30 cement concrete to carry a safe working load not less than specified ,excluding the cost of steel reinforcement but including the cost of boring with casing and/ or bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of pile to be embedded in the pile cap etc. complete including removal of excavated earth with all lifts and leads, (length of pile for payment shall be measured from top to shoe to the bottom of pile cap) 600 mm dia piles.

Chipping of RCC pile heads by way of chiseling/through cutter etc up to cut of level by manual means (Dia 600 mm)

Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading plate form and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of engineer-in-charge. (single pile upto 100 tonne capacity (2% of total piles as per code)

Initial test

Routine test

Conducting of bores for checking bearing capacity of soil including collection of samples at different levels upto bore depth of 10 metres including carriages of all equipments and conducting of soil tests in the lab complete job

Providing and erecting 2.00 metre high temporary barricading at site as per direction of engineer-in- charge The barricading provided shall be retained in position at site continuously i/c shifting of barricading from one location to another location as many times as required during the execution of the entire work till its completion. Rate include its maintenance for damages, painting, all incidentals, labour materials, equipments and works required to execute the job. (Note :-one time payment shall be made for providing barricading from start of work till completion of work including shifting. The barricading provided shall remain to be the property of the contractor on completion of the work).

Earthwork in excavation by manual / mechanically means in trenches for foundation, drains, pipes, cabels etc (exceeding 1.5 M, in width)and for shafts, wells, cesspits and the like exceeding 10Sqm on plan, depth upto 1.5M including disposal of excavated earth upto 1mtrs from cutting edge, disposed earth is to be levelled and neatly dressed in all kinds of soil.

Providing and laying of stone soling hand packed and compacted with hand roller including carriage complete.

Providing and laying in position cement concrete of 1:4:8 grade excluding the cost of centering and shuttering. All work upto plinth level (Crushed aggregate 40mm).

Providing and laying in position reinforced cement concrete 1:1.5:3 (1 Cement: 1.5 coarse sand: 3 graded Stone aggregate 20mm nominal size) excluding cost of centering, shuttering, finishing and reinforcement. All work upto plinth level.

Providing and laying in position cement concrete of specified grade excluding cost of centering and shuttering 1:3:6 mix (1 Cement: 3 coarse sand: 6 graded Crushed Stone aggregate 20mm nominal size) all work up to floor V-level including all carriages and cost of material involved.

Providing and laying in position reinforced cement concrete 1:1.5:3 (1 Cement: 1.5 coarse sand: 3 graded Stone aggregate 20mm nominal size) in suspended floors, balconies, landings and staircase having upto 15 degree slope. excluding cost of centering, shuttering, finishing and reinforcement. All work upto floor V level.

Centering and shuttering including strutting, propping etc. and removal of form work for foundation footings, bases of columns.

Centering and shuttering including strutting, propping etc. and removal of form work for Walls ( Any thickness) incl attached pilasters, buttresses, plinth & string courses etc (using 12mm water proof ply)

Centering and shuttering including strutting, propping etc. and removal of form work for lintel beams, plinth beams, girders, bressumers and cantilevers. (using 12mm water proof ply)

Centering and shuttering including strutting, propping etc. and removal of form work for Columns, pillars, piers, abutments, posts & struts. (using 12mm water proof ply)

Centering and shuttering including strutting, propping etc. and removal of form work for suspended floors, roofs, landings balconies and access platforms. (using 12mm water proof ply)

Centering and shuttering including strutting, propping etc. and removal of form work for Stairs (excluding landings) except spiral staircases. (using 12mm water proof ply)

Edges of slabs and breaks in floors and walls under 20cms wide

Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete (Thermo Mechanically Treated Bars)

Supplying & filling of Sand/ Nallah Muck under floors incl. watering, ramming, consolidating and dressing incl. all carriages, leads and lifts

Filling avalable excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming & watering lead upto 50mtrs and lift upto 1.5m.

Disposal of Excavated Earth beyond 50 Mtrs by M.T. upto 2 to 3 Kms due to restrained place at site of work.

Providing / laying of GSB of specified size in layers not exceeding 22cm in thickness and maximum size of stone agg, not exceeding 90 mm including watering, spreading, and consolidation with PRR of 8-10 ton capacity including carriages of all materials with loading , unloading and staking complete

Providing and fixing of 20mm dia 450mm long bolt full thread with nuts and washers for anchoring the wooden structure incl welding the bolts at bottom with 20 mm flat iron strip of at least 200mm long complete job.

Structural steel work welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

P/F pre-colour coated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by engineer-in-charge) 0.50mm +/-5% total coated thickness (TCT) Zinc coating 120gsm as per IS:277 in 240 mpa steel grade 5-7 microns epoxy primer on both sides of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/ self tapping screws of size (5.5x55mm) with EPDM seal or with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G. I, limpet filled with white lead complete up to any pitch in horizontal/vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required:

Providing and fixing pre-coated galvanized steel sheet roofing accessories 0.50mm (+/-5%) total coated thickness (TCT) Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and GI: Seam bolts and nuts, GI plain and bitumern washers complete. (Ridges plain (500 – 600mm)

Providing and fixing of 300 x 35mm thick Ist class kail wood eves boarding incl cost of nails.

P/F of 12mm thick T&G planks made of imported wood (New zealand pine or equivalent) for roof soffits & Ceiling on wood work in false ceiling, partitions sawn and put-up in position in budloo wood (Frame work). including cost of necessary adhesive & cost of nails etc.complete job. incl cost of nails / screws incl cost of Polish/ Finishing to be approved by Engineer-in-charge.

P/F of 50mm x 50mm thick budloo wooden cornice fixed with nails.

Brick work with FPS bricks of class designation 75 upto floor V level in cement mortor 1:6 (1 cement :6 coarse sand) incl carriage of all materials involved complete job.

Providing l wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position. (2nd class Deodar Wood).

Providing 40x5mm flat iron hold fasts 400mm long incl. fixing with frames with 10mm dia bolts, nuts wooden plugs and embeded in c. conc. Block 30x10x15cm in M-10 G.

15mm thick cement plaster on the rough side of single or half brick wall of mix 1:6 (1 cement :6 fine sand)

12 mm thick cement plaster on the External walls using mix 1:6 (1 cement :6 Fine sand) incl. cost of scaffolding complete job.

6 mm thick cement plaster on the Ceiling using mix 1:4 (1 cement :4 Fine sand)

Providing & applying Plaster of Paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete..

Distempering with oil bond washable distemper of approved brand and manufacture to give an even shade New Work (two or more coats over) and including priming coat with cement primer

Providing and applying white cement based putty of average thickness 2mm, of approved brand and manufacture, over the plastered wall surface to prepare the surface even and smooth complete.

Finishing walls with water cement paint of approved brand and manufacture on new works including applying one coat of water thinable cement primer of approved brand and manufacture on wall surface .

Providing & applying Exterior Rustic Texture Emulsion of thickness not less than 3mm over one cement based priming coat on new surface with rustic using exterior weather coated spray emulsion of specified colour & shade of approved manufacture complete including all necessary scaffolding etc. as directed by EIC at site complete.

Providing and fixing Ist quality ceramic glazed tiles conforming to IS:13753 of minimum thickness 5mm of approved make like NITCO. ORIENT, SOMANY, KAJARIA or equivalent make in all colour, shades except begundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slury @ 3:3 Kg per Sqm including pointing in white cement mixed with pigment of matching shade complete. including carriage of material.(Wall tiles)

Providing and fixing ceramic Antiskid floor tiles 300x300 mm (thickness to be specified by the manufactures) of Ist quality conforming to IS:13755 of NITCO, ORIENT, SOMANY, KAJARIA or equivalent make in colour such as white, ivory, grey, fume Red,brown laid on 20mm thick be bed of cement mortar 1:4 (1 cement :4 coarse sand) including pointing the joints with white cement and matching pigment etc. complete including carriage of material (including cost of all material, leads, lifts and carriages etc upto site of work complete).

Providing & laying 18mm minimum thick pre-polished (best quality) granite stone (Chima Pink / Textured Black/ other shade) slabs (non water absorbing) in skirting / riser of steps landing on 20mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand)/12mm thick backing of cement mortar 1:3 (1 cement : 3 coarse sand) and joined with white cement slurry mixed with pigment or with standard tile made compound to match the shade of the slab. Including rounding, rubbing, clamping, curing, molding, granite polish & making grooves as required complete (Note: The stone slab shall be cut to required size and laid to the required pattern including rounding, chamfering, bull nosing of the edges as directed. Actual areal of slab, as laid shall be measured) Sample to be approved by Engineer-in-charge.

Providing edge molding to 18 mm thick Granite / marble stone counters, vanities etc incl machine polishing to edge to give high gloss finish etc. (Double Molding) using glue type adhesive Araldite of Pedilite make for holding the bottom side of the molding (including cost of all material, leads, lifts and carriages etc upto site of work complete).

Providing and laying VC shield Vitrified tiles 8-10mm thick, scratch & strain resistant with high abrasion resistant glaze equivalent to group-25 or VC shield of Somany make or equivalent, sample to be approved by Engineer-in-charge. Size of Tile 600 x600 mm.

Applying priming coat on new wood and wood based surface with ready mixed wood primer

Preparing wooden based surfaces by knifing grey paste filler of approved brand & manufacture.

Painting with synthetic enamel paint of approved brand and manufacture of required shade and colour to give smooth finish with two or more coats on new wood and based surfaces

Providing and fixing of 32mm paneled or paneled and glazed shutters for window and clearstory windows incl. ISI marked black enameled MS Butt hinges with necessary screws using 1st class Kail Wood.

Providing and fixing of 35mm wire gauze shutters for window and clerestory windows incl. ISI marked black enameled MS But hinges with necessary screws using 1st class Kail Wood.

Providing & fixing ISI marked flush door shutters (Water Proof) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3mm pre laminated with vertical grains or cross bands on both faces of shutters, 35mm thick including ISI marked anodized aluminum butt hinges with necessary screws.

P/F of 12 mm dia heavy duty Stainless Steel Superior quality Hardware Items:

a)Tower bolts 150mm

b)Tower bolt 200mm

c)Handle 150mm

d)Handle 200mm

e) I Hook 125mm

f) Link Locks as per approved design & pattern

Providing and fixing of Aluminum Composite sheet cladding (exterior grade)/ Powder Coated Aluminum work incl glazing with glass panes of 5.5 mm thickness (weight not less than 13.75kg/sqm) with extruded built-up tubular sections / appropriate Z sections and other sections of approved make conforming to IS 733 and IS 1285, fixed with rawl plugs and screws incl necessary filling up of gaps at junctions, at tops, bottoms and sides with required PVC / neoprene felt etc. all complete as per directions of Engineer I/C for fixed portion, (minimum thickness of powder coated 50 microns)

Supply and installation of satin finish stainless steel AISI 304 stainless steel handrail and balustrade system having 50mm dia tube handrail (1.5mm gauge) weight 3.70 kg, erected with chemical grout to be fixed on the top of slab/skirting (Spigot Fixed) at max c/c distance of 600mm complete with all necessary bends and terminations complete, with cover plate, fixings, end terminations, custom bends, as manufactured by Dline or approved equivalent. Height shall be 1050 mm above the finished skirting level complete as per architectural drawings, pattern & design to be approved by Engineer-in-charge.

Supply and installation of satin finish stainless steel AISI 304 stainless steel Posts having 100mm dia tube, erected with chemical grout to be fixed on the top of slab/skirting (Spigot Fixed) at corners complete, as manufactured by Dline or approved equivalent & shall be fixed above the finished level complete as per architectural drawings.

Providing and fixing of 4 mm thick glass panes for window shutters incl cost of beading & nails etc complete job.

Making outside Border 3" wide along the wall by way of raised plaster in 1:3 mix ( 1 Cement: 3 Fine sand) including cost of all materials involved & required scaffolding all complete incl. Finishing wall with two or more coats with Acrylic smooth exterior paint (Apex) incl cost of cement primer (Terra-cota).

15 mm cement plaster 1:3 (1cement: 3 coarse sand) finished with a floating coat of neat cement on the rough side of single or half brick wall

Dry random rubble masonry in foundation and plinth using quarry stone with bond stones

B- SANITARY / PLUMBING:- Providing and fixing of following size of PVC Fitting ISI Marked (Prince/ Supreme or Equivalent)

100mm dia Door Tee

100mm dia Plain Bend

100mm dia Collar.

100mm dia P-Trap

100mm Door Bend

100mm PVC Prince Cliff

100mm x 75mm dia Reducer

100mm 45 deg Bend

75mm 45 deg Bend

75mm dia Door Bend

75mm dia Door Tee

75mm dia Plain Bend

75mm dia Collar.

75mm dia Floor Trap.

75mm PVC Prince Cliff

75mm dia PVC Cowel Caps

Providing and fixing of following size of PVC pipe including C/O (B-Type, specified adhesive. (Prince/ Supreme or Equivalent)

a) 100mm dia Pipes PVC Prince.

b) 75mm dia Pipes PVC Prince.

c) 50mm dia Pipes PVC Prince.

Providing, laying and fixing heavy duty Glass Fibre reinforced PPR (Polypropylene Random- Copolymer) pipes & Fittings of approved quality with solvent weld socket joints and necessary (female Elbow fittings brass thread) such as sockets, back nuts, elbows, bends, tees, reducers, enlargers, plugs, clamps, Transition Bushing, unions etc. including necessary excavation, backfilling, fixing with clamps, drilling holes in walls, slabs, hydraulic testing complete job.

16mm dia

20mm dia

25mm dia

32mm dia

40mm dia

50mm dia

Supply, installation, testing and commissioning of gunmetal, male or female threaded isolation control valve (Ball Valve), of approved quality confirming to IS 778, PN 10, with necessary specials, unions, nipple etc., to complete the job.

16mm dia

20mm dia

25mm dia

32mm dia

40mm dia

50mm dia

Providing and fixing water closet squatting pan ( Indian type W.C. Pan ) with 100 mm sand cast iron P or S trap, 10 litre low level P.V.C flushing cistern ( of approved make) with manually controlled device (handle lever) conforming to IS:7231, with all fittings C.I/M.S. rackets, 32 mm diameter flush pipe with fittings and clamps, over flow arrangement with specials and mosquito proof coupling of approved municipal design complete including painting of fittings and brackets, cutting and making good the walls and floors wherever required. Orissa pattern white vitreous china W.C pan of size 580x440 mm with integral type foot rests.

Providing and fixing of 32mm dia C.P long bend for WCs.

Construction of Brick masonry plate form for WC's using 2nd class bricks in 1:6 mix incl carriage of all materials involved.

Providing & Fixing first quality white vitreous china pedestal type water closet (European type) of approved qualitywith seat and lid, CP hings and rubber buffers C.I./M.S brackets, including connection 1.20 mtr ,40 mm dia flush bend with fittings and clamps, overflow arrangements with special and mosquito proof coupling of approved muncipal design including painted of fittings and brackets ,cutting and making good the wall and floors wherever required.

Providing & Fixing first quality white vitreous china pedestal type water closet ( European type WALL HUNG) with seat and lid, CP hinges and rubber buffers incl brackets ,cutting and making good the wall and floors wherever required.

Providing and fixing CONCEALED flushing cistern (8 to 10) liters capacity embebed inside the wall incl making the cavity inside the brick wall with all accessories complete job.

Providing and fixing Stainless steel Rack bolts 250mm long with all accessories complete job.

Providing & Fixing first quality "VANITY TYPE" white vitreous china oval wash basin 600 x 600 mm specially fabricated PVC counter type fixed with all accessories incl looking glass & top shelf cabinet rack complete job, Colour & type to be approved by the Engineer incharge.

Providing and fixing of CP Health Faucet 900 mm long complete of standard make.

Providing and fixing CP 2 in 1 Bib Cock heavy (Standard make) (Jaguar/ Cera or equivalent)

P/F wash basin with C.I. / M.S. brackets, 15mm C. P brass pillar taps, 32mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required: flat back white vitreous china wash basin size 630x450mm with a pair of 15mm C. P. brass pillar taps.

Providing and fixing of vitreous Pedastal complete of standard make.

Providing and fixing Stainless Steel Sink of size 18" x 24" heavy (Standard make)

Providing and fixing CP short body Bib Cock heavy (Standard make) (Jaguar/ Cera or equivalent)

Providing and fixing CP long body Bib Cock heavy (Standard make) (Jaguar/ Cera or equivalent)

Providing and fixing CP Angle valve (Standard make) (Jaguar/ Cera or equivalent)

Providing & Fixing C.P. Single hole Mixer of approved quality for wash basin of approved make including cutting and making good the walls wherever required. (Jaguar/ Cera or equivalent)

Providing & Fixing 15 mm dia C.P Wall mixer of approved quality (Non telephonic) of standard design and of approved make complete including C.P. wall flange, cutting and making good the walls wherever required. (Jaguar/ Cera or equivalent)

Providing & fixing C.P. Sink mixer of approved quality with swinging casted spout wall mounted complete including cutting and making good the walls wherever required. (Jaguar/ Cera or equivalent)

Providing and fixing CP Pillar Cock heavy (Standard make) (Jaguar/ Cera or equivalent)

Providing and fixing CP waste Coupling

Providing and fixing PVC Waste pipe

Providing and fixing of 6" geyser bolts of standard make

Providing and fixing CP Soap case.

Providing and fixing of CP Grating with Anti Cockroach trap below the grating hinge type.

Providing and fixing 15mm dia 2"- 3" long CP nipples.(50mm – 75mm)

Providing and fixing PVC connection pipe upto 24" long.

Providing and fixing CP Towel Rod

Providing and fixing CP Towel Ring

Providing and fixing CP cup

Providing and fixing looking Mirror (Belgium Type)

Providing and fixing of Steel Shelf of Superior quality

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked indicating the BIS license No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank (sintex, electroplast, star, lotus or equivalent having valid ISI license. (Three layer)

Construction of Brick masonry manholes using 2nd class bricks in 1:6 mix including plastering /CI frame with cover, Complete Job of following sizes.

Providing and fixing 1.0 H.P. Motor/ Pump from Crompton Greaves or Equivalent standard make complete job incl power supply & MCB for control.

Providing, installation, commissioning and testing Hot water Geyser of approved make (Venus, Racold, Jaguar or equivalent) including fixing with bolts and making necessary connections.

50 litre capacity

05 litre capacity Instant Geyser

C- Electrification Part-1 Supply, installation, testing and Commissioning of Sub Station:

9 mts steel tubular pole post 410 (SP-33) IS 2713 (part-II) 1990 as per REC Standard

MS Channel iron(ISLC 100 designation) 100x50x50x6 mm 9' long (2 No) duly fabricated as per site requirement and painted with two coats of Red oxide and Al. Paint as per REC Standard .

MS Channel iron(ISLC 75 designation) 75x40x40x6 mm 9' long (8No) duly fabricated as per site requirement and painted with two coats of Red oxide and Al. Paint as per REC Standard

MS Channel iron(ISLC 75 designation) 75x40x40x5 mm 6' long (2 No) duly fabricated as per site requirement and painted with two coats of Red oxide and Al. Paints per REC Standard .

MS Angle iron braces (ISA 5050 designation) 50x50x6mm 6' long (4 No) duly fabricated as per site requirement and painted with two coats of Red oxide and Al. Paint as per REC Standard

Providing of Chemical Earthling of Sub-Station for neutral earthing 2 mtr long 50mm dia GI to copper with additional 1 length GI pipe 38mm connected with chemical earthing and with extension of GI strip 25*3mm upto all equipments. Earthing has been laid through insulators to avoid with the existing structure for LA.

Galvanized Nuts & Bolts & washers of sorts. (Galvanized as per IS-2633/1986)

GI Strip for Earthing 25x5mm as per REC Standard

200KVA transformer11kV/440 Volts oil cooled Aluminum wound outdoor Type conforming to IS 1180 level II IS Standard ( as amended upto date and CBIP manual)

300 mm² PVC single core LT cable conforming to IS 1554 (part -I) 1988 Havells/Polycab make for incoming and outgoing circuits to be connected with LT Network including thimbling with 300 mm sq Al lugs.

Bi metallic Clamps19mm².

11KV 400 AMP Gang Operated switch gear

Drop-out set (Horn-gap type) as per REC standard F6

11KV Lighting Arrester Set (Station type) as per REC standard conforming to IS 3070 part -III and as per REC standard

11KV pin with insulators Brown glazed porcelain insulator confirming to IS-731/1971 Amendments 1 to 5 type B with 320mm minimum creep age distance and with lead/Zinc thimbles suitable for use with G.I forged pin having small steel heads as per IS-4l86 (P.I) 1993 and IS-2486 (P.II)1989 and revision with latest amendments if any as per REC Standard C-1

Danger plate as per REC Standard

Earthing for sub-station poles as per REC Standard (J-1) (Spiral Type)

Earthing insulating boots

Providing, Erection, testing & commissioning of MS Angle iron for Transformer Belt (ISA 5050 designation) 50x50x6mm 10' long duly fabricated as per site requirement and painted with two coats of Red oxide and Al. Paint as per REC Standard

Ant climbing Device as per REC Standard

Sign Board

Cement bottoming of pole structures as per REC drawing enclosed

Painting of poles/ structure with 2 coats of Al. & red oxide paint and painted of orange colour as per REC Standard

Supply, installation, testing and commissioning of 11 Kv Line:- 9 Mts steel tubular pole post 410 (SP-33) IS 2713 (part-II) 1990 as per REC Standard.

35mm² AB Cable 11 kv, Havells/Polycab make

Heat Shrinkable Outdoor Cable Termination Kit

Suspension/Tension Clamp with eye hook

Galvanized Nuts & Bolts & washers of sorts. (Galvanized as per IS-2633/1986)

11KV pin with insulators Brown glazed porcelain insulator confirming to IS-731/1971 Amendments 1 to 5 type B with 320mm minimum creep age distance and with lead/Zinc thimbles suitable for use with G.I forged pin having small steel heads as per IS-4l86 (P.I) 1993 and IS-2486 (P.II)1989 and revision with latest amendments if any as per REC Standard C-1(for tap line)

Cement bottoming of pole structures as per REC drawing enclosed for tap line

Earthing for poles as per REC Standard (J-1) (Spiral Type)tap line

Painting of poles/ structure with 2 coats of Al. & red oxide paint and painted of orange colour as per REC Standard tap line

Supply, installation, testing and commissioning of LT panel:- LT Prodigy Meter with all accessories

Supply, providing and installation /commissioning of Moulded Case Circuit Breakers (AC 415V) MCCB 630 A, 4-pole 50KA having adjustable Thermal & adjustable Magnetic setting of /Havell's/Schneider/Legrand make, installed in main panel

Supply, providing and installation /commissioning of Moulded Case Circuit Breakers (AC 415V) MCCB 100 A, 4-pole 35KA having adjustable Thermal & adjustable Magnetic setting of L&T/Havell's/Schneider make, installed in main panel (for security lights)

Supply, providing and installation /commissioning of Four Pole Changeover with Advance Neutral (AC 415V) On-Load Changeover Switch I-O-II, Conforming to IS standards 200amp of L&T/Havell's/Schneider make, installed in main panel (for DG supply)

Supply, providing and installation /commissioning of Four Pole Changeover with Advance Neutral (AC 415V) On-Load Changeover Switch I-O-II,for security lights, Conforming to IS standards 63 amp of L&T/Havell's / Schneider make, installed in main panel

LT Shackles Insulators brown glazed 90X75MM along with mukki clamps clamp

Galvanized Nuts & Bolts & washers of sorts. (Galvanized as per IS-2633/1986)

Part-2 WIRING PART :- Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable Finolex/ Havells/Polycab make in surface / recessed medium class PVC conduit(Ravinder/ polycab/ Alba make),complete in all respects as per standard specifications incl cost of conduit .

Lighting points/Bell points

Fan/Exhaust fan points

Wiring for 3-5 pin sockets/indicator points with 1.5 sq.mm FR PVC insulated copper conductor single core cable Finolex/Havells/Polycab with earthing wire of same specification(socket points) in surface / recessed medium class PVC conduit,Ravinder/polycab/Alba make),complete in all respects as per standard specifications excl. cost of conduit

3/5 pin socket points

Indicator points

Wiring for circuit/ submain /fire alarm point wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable Finolex/Havells/Polycab in surface/ recessed medium class PVC conduit Ravinder/polycab/Alba make),as required (as per Schedule)

2.5 Sqmm including earth wire

16 sq mm from sub boards to sub boards with earthing wire

25 sq mm copper multistoried wire

4 Sq mm including earth wire

TV /LAN & Telephone wiring part:- RG6 Co-axial Cables (Electrolytic Grade solid annealed Copper conductor, Jelly Field, Aluminium Foiled and Aluminium wire Braided) Havells/polycab/finolex make ,Laid in separate conduit Ravinder/polycab/Alba make)incl cost of conduit.

Telecom Switch Board Cables ,2 pair (PVC Insulated Telephone cables for indoor applications confirming to TECHNICAL specification )Havells/polycab/finolex mak,Laid in separate conduit Ravinder/polycab/Alba make)incl cost of conduit.

Telecom Switch Board Cables ,3 pair (PVC Insulated Telephone cables for indoor applications confirming to TECHNICAL specification )Havells/polycab/finolex mak,Laid in separate conduit Ravinder/polycab/Alba make)incl cost of conduit.

Supplying all material, storing, handling, fixing, laying wiring and testing for computer LAN points duly laid in CAT 6 cable(Electrolytic grade solid annealed bare copper conductor, 4 Pair unshielded twisted pair (UTP) Industrial cables for LAN Network (D-Link,HAVELLS/POLYCAB make) in concealed medium class PVC conduit complete in all respects as per standard specifications incl. cost of conduit/Channel Ravinder/polycab/Alba make)

Accessories part :- Supplying & fixing of following modular switch/ socket on the switch box including connections but excluding modular plates etc as required.( Make Legrand/Phillips ) as per the approved sample

6 ampere 1 way switch(brown/white)

Bell push 10 A

6A 3 Pin Socket

Telephone jack/Socket with shutter RJ11

T V dish Socket /jack with cable grip

RJ 45,Cat 6 Computer socket with shutter

16A 3pin Socket

16A 3pin switch

Dummy/Blank

Phase Indicator with LED

Buzzer

Supplying & fixing of following modular Plates with iron/GI boxes.( Make Legrand/ Phillips/Make) as per the approved sample switch cover plate with mounting frames and GI box

Supplying & fixing of pvc ceiling roses

Supplying & fixing of PVC Fan plates

FAN & EXHAUST FANS:- Providing and fixing of exhaust fan 200mm with allied accessories crompton/Havells/Usha make

Providing and fixing of 1200mm Sweep ceiling fan five star rated with allied accessories complete including necessary terminations crompton/ Havells/Usha Make.

Providing and fixing of exhaust fan 250mm with allied accessories crompton/Havells/Usha/orient make

Providing and fixing modular stepped type fan dimmers including necessary terminations as requried of Legrand /Phillips make

Earthing Part :- Providing and fixing of maintanence free chemical earthing including digging/drilling of 2mtr deep pit in hard/semi hard soil, chemical material and layng of pipe electrode with external dia of 50 mm and internal strip of 32x5 mm GI make with back fill compound 50 kg in the pit and disposal of unwanted material from earthing site to disposal site, and earthing should provide desrible earth resistance value as per IS standards

LED Down lighters /Tube Fittings:- Providing and fixing of LED lights of following type Syska make including necessary terminations as required.

T-5 LED 4' long 20watt

T-5 LED 2' long 9 watt

Providing and fixing of various types LED lights IP-65 protection grade slim fit downlights,with edge superior light output technology with allied accessories and terminations complete, crompton/ phillips/Havells make

LED 12 watt surface/conceal type

LED 15 watt surface/conceal type

LED 18 watt surface/conceal type

T-5 LED Mirror light

Providing and fixing of 20 Watt LED ,flood light IP65 certified, having constant voltage and current LED Driver, with Lens type LED crompton/syska/philips/Havells make.

Control gear/Distribution boxes:- Providing and fixing of following TPN horizontal /Vertical distribution boards, confirming to IP43 standards, double door with inbuilt tinned copper heavy duty bus bars for earth, having jumpers of proper current rattings Havells/Legrand/hager make.C Curve

Providing and fixing of following type of Legrand C curve MCB's of including testing and necessary terminations.

63A SPN(DP)

32A SPN(DP)

6A-20A SP MCB

Providing/fixing and installation of ACCL(Automatic Source Changeover with Current Limiter) Microcontroller based DIN rail mountable automatic source changeover with neutral isolation Havells/Legrang/Schiender make,with Mains 30A / Gen 1.5A to 20A Indication Mains, Generator, Load, Overload (UPS)

SUB PANNEL's for four floors: Providing and fixing of Sub Main powder coated Pannels in 14 swg with aluminium Bus bars and allied accessories of different size chambers consists individual doors for MCB's and MCCB's, energy meter chambers and other switch gears etc as per IS standards and requirement complete with following details including grouting/earthing with foundation complete. MCCB's should be Legrand/Siemens make, MCB's should be Legrand c curve make, CT's Meter should be AE/Rishab/Morley Make

Aluminium buss bars and allied accessories

Pannel size (3'-0"x3'-0'x1'-0") = 9 cfts

MCCB 125 A, 4-pole 35KA having adjustable Thermal & adjustable Magnetic setting of Legrand/Havell's/Schneider make,

MCCB 100 A, 4-pole 35KA having adjustable Thermal & adjustable Magnetic setting of L&T/Havell's/Schneider make,

Digital multi functional meter with CT's and indicator complete of Automatic/Rishab/Universal make

Supply, providing and installation /commissioning of Moulded Case Circuit Breakers (AC 415V) MCCB 630 A, 4-pole 50KA having adjustable Thermal & adjustable Magnetic setting of Legrand/Havell's/Schneider make, installed in main panel

Supply, providing and installation /commissioning of Moulded Case Circuit Breakers (AC 415V) MCCB 200A, 4-pole36KA having adjustable Thermal & adjustable Magnetic setting ofLegrand/Havell's/Schneider make, installed in main panel

Supply, providing and installation /commissioning of Moulded Case Circuit Breakers (AC 415V) MCCB 100 A, 4-pole 35KA having adjustable Thermal & adjustable Magnetic setting of L&T/Havell's/Schneider make, installed in main panel

Supply, providing and installation /commissioning of Four Pole Changeover with Advance Neutral (AC 415V) On-Load Changeover Switch I-O-II, Conforming to IS standards 200amp of L&T/Havell's/Schneider make, installed in main panel

Supply, providing and installation /commissioning of Four Pole By Pass Switch (AC 415V) Conforming to IS standards 200amp of L&T/Havell's/Schneider make, installed in main panel

Providing, installation, testing and commissioning of Outdoor type with water proof canopy ,125KVA 3 phase AVR servo stabilizer ,oil filled, WITH I/P 157-o/p 470 (unblanced load)complete with installation and cost of cement concrete foundation .ALBA/COSCO /Chinar make as per IS 9815 & 2026

Cabling/Service line part:- 240 sq mm 3.5 core Aluminum conductor , XLPE Insulated, PVC tape/Extruded Inner sheathed for Multicore Cables, Armoured as per IS, PVC Type ST2 sheathed, 650/1100V grade as per IS 7098(Part 1) 1988 Havells/Polycab make{Main operational line along with one spare line of same specifications with necessary( aluminium) thimbling of appropriate size

120 sq mm 3.5 core Aluminum conductor , XLPE Insulated, PVC tape/Extruded Inner sheathed for Multicore Cables, Armoured as per IS, PVC Type ST2 sheathed, 650/1100V grade as per IS 7098(Part 1) 1988 Havells/Polycab make{Main operational line along with one spare line of same specifications with necessary( aluminium) thimbling of appropriate size }

ONLINE UPS:- Supply /Installation and commission of EATON/Reputed make 6KVA Online UPS System with single phase input and single phase output/double conversion technology, wide input range, automatic bypass cold start on batteries ,LCD Display, having PF 0.9(approx.)

Supply /Installation and commissioning of Amron/reputed make 12Volt/42AH SMF VRLA Type Batteries for providing backup time upto 60 minutes

Input /output cables

Battery Link set

Iron rack for batteries

Lightening Protection:- Providing and fixing of ESE Type Lightining Protection for de-ionisation ELTEC /reputed make level 2 covering an area of 200 meters(apx) around with all allied accessories/fitments ,complete job

Providing and fixing of 70 sq mm copper flexible cable in PVC Conduit fixed with saddles clamps etc to earth termination as reqd including all allied items/fitments ,complete job

Providing and fixing of lightening strike counter having high sensitivity with 2.5 sq mm copper flexible cable from LA top to desired point, complete with all allied accessories/fitments

Providing and fixing of maintenance free chemical earthing including digging/drilling of 2mtr deep pit in hard/semi hard soil, chemical material and layng of pipe electrode with external dia of 50 mm and internal strip of 32x5 mm GI make with back fill compound 50 kg in the pit and disposal of unwanted material from earthing site to disposal site, and earthing should provide desrible earth resistance value as per IS standards

Part-3:- Supply, handling, fabrication and erecting of 8mtr. long hot galvanized octagonal pole make Phillips/Bajaj/Utkarsh ,standard make,(as per approved sample)having bottom dia 130-150 mm, top dia 70 mm made of 3mm thick HT Sheet along with base plate size 200-240 mm x 200-240 mm x 16mm ,including four no,s of foundation bolts with specification M20 X 700mm long with door size of 500 mm.(as per approved sample)complete with connectors and suitable amperage MCBs

Supply, handling, fabrication and erection of 1 mtr long hot dip galvanized double sided cross Arm,duly modified (as per the site requirement)arm, Phillips/Bajaj/Crompton/Utkarsh make

Design ,laying of specified cement concrete bottoming for 8mtr. long hot galvanized octogonal pole in 1:2:4 mix RCC.The cost includes ,cost of carriage of all materials upto site and all allied civil works ,complete job, as per REC Standards. including frame of 12mm dia Reinforcement complete.

Supply, Installation, testing & Commissioning of earthing to poles using G.I strip complete job as required as per REC norms

Supply, assembling, installation of Phillips/Havells (as per approved sample)100/110 watt LED flood Light powder coated, pressure die cast aluminium housing with heat sink IP 66 protected, with input voltage AC90-300V 50 Hz, incl testing and commissioning

Supply and laying of steel armoured PVC insulated XLPE 16 sq mm 4 core of Polycab/KEI /Havells make Aluminium cable . The cable is laid underground buried in soil in HDPE PIPE. . The job includes termination peeling thimbling of cable and laid under soil as required

Supply and laying of armored PVC insulated XLPE 10 sq mm 4 core of Poly cab/KEI or equivalent make Aluminium cable . The cable is laid underground buried in soil. The job includes digging out trench for laying of cable incl. neatly refilling of same.

Providing laying of 2.5 sq mm PVC insulated multi-strand copper conductor single core cable with testing and commissioning Havells/ Polycab/Finolex make

Providing laying of 4 sq mm PVC insulated multi-strand copper conductor single core cable with testing and commissioning Havells /Polycab/Finolex make

Providing and fixing of main outdoor feeder pillar panel ,Powder coated, weather proof canopy type with lockable arrangements fabricated out of 16 SWG sheet steel ,front door operated with Siemens grey colour Aluminum bus bars 25x 6 grade 1 , mounted on epoxy insulators , Digital multifunctional meter VIF meter and panel indicators complete with inner wiring .The panel is providing with angle iron stand for installation , grouted in cement concrete block and properly earthed.

Supply and fixing of 63 Ampere 4 pole termination connector incl testing and commissioning.

Providing fixing testing and commissioning of 100 ampere TPN MCCB’s (MAKE Schinieder / Havells) complete with connections

Providing and fixing of 32 -40 ampere DP MCB's (Make schineder/Havells/Legrand) complete with connections, testing and commissioning etc as required

Supply ,Installation, testing & commissioning of 10KVA 3 phase automatic voltage stabilizer, servo control , oil cooled (I/P 90-240V O/P 220V) of Servo point make incl making of necessary Protections/connections as red…ALBA/Cosco/ Chinar make along with canopy, Outdoor type (water proof arrangements)

Supplying and laying of appropriate/32 Sqmm, HDPE Pipe laid underground incl. all ccessories complete as required ,work includes excavation of earth and earth -re filling ,making the top surface smooth after completion of the job

Providing and fixing installation commissioning of onload change over switch 63 amp 4 pole Legrand /Schinieder/Havells make complete with connections etc

Providing and fixing of maintenance free chemical earthing including digging/drilling of 2mtr deep pit in hard/semi hard soil, chemical material and layng of pipe electrode with external dia of 50 mm and internal strip of 32x5 mm GI make with back fill compound 50 kg in the pit and disposal of unwanted material from earthing site to disposal site, and earthing should provide desirable earth resistance value as per IS standards

SABZAR AHMAD ROY

ARIF JAN QADRI