SPECIAL REPAIR/ REPLACEMENT OF OH TO UG CABLE AND ALLIED WORKS AT 21 MAHAR AND MD ACCN, PROVN OF FIRE HYDRANT SYSTEM INCLUDING PUMPING COMPLETE SET FOR STATIC WATER TANK AT SDP AND CERTAIN MINOR WORKS UNDER GE(U) MEERUT

Amount

Supply and Laying XLPE UG cable PVC insulated,bedded armoured heavy duty electric cable 1100 volts grade with aluminium conductor of size 120 Sqmm 3.5 core in trenches or fixed on wall/floor/ pole complete all as spd and directed.

Supply and Laying XLPE UG cable PVC insulated,bedded armoured heavy duty electric cable 1100 volts grade with aluminium conductor of size 50 Sqmm 3.5 core in trenches or fixed on wall/floor/ pole complete all as spd and directed.

Supply and Laying XLPE LT UG cable PVC insulated,bedded armoured heavy duty electric cable 1100 volts grade with aluminum conductor of 25 Sqmm 4 core in trenches or fixed on wall/floor/poles complete all as specified and directed.

Supply and Laying XLPE LT UG cable PVC insulated,bedded armoured heavy duty electric cable 1100 volts grade with aluminum conductor of 10 Sqmm 4 core in trenches or fixed on wall/floor/poles complete all as specified and directed.

Supply, installing, errecting, testing and commissioning, factory made and tested LT Panel board with all accessories. LT switchgear panel board of size 1000mmx1050mmx500mm, OUT DOOR type, platform mounted, suitable for 415 volts 3 phase 4 wire, 50 Hz AC supply system, having bus bar chamber with insulated Aluminum busbars 2 installed on porcelain / SMC insulators and all interconnection between main busbars as well as outgoing feeders shall be carried out with TPN Aluminum busbar of rating not less then 1.5 times rated capacity of individual out going feeders. The panel shall be dust and vermin proof, IP 56 class protection and made of 3.15 mm CRCA MS sheet and 50x50x6mm thick angle iron frame work, bottom channel of size: 70x40x5 mm powder coated finish over one coat of red oxide primer outside and two coats of red oxide primer on inside, front / back opening type, and fixing 2 Nos.danger notice plate with letter, figures and conventional skull bones in signal red colour and fixed front & back door to LT panel etc with voltage and danger indicated in Hindi and English, with double door shutter and locking arrangement (including provn of 65mm Godrej (Freedom) stranded lock with 2 keys, internal wiring with PVC insulated, stranded copper conductor, FRLSH cables, IS-694 marked of adequate size but not less than 1.5 Sqmm. The platform shall be such that it is of a height 30 cm above the nearest ground level. complete all as specified and directed including connections of all out going/in coming existing cables of size 25 to 400 sqmm by drawing /digging out cable from loops in trenches/ ducts out side the Bldg inclusive of necessary excavation and earth work as required and relaying the cables with retrieved bricks and providing new sand cushioning and crimping suitable size Alluminium lugs for terminal connections of cables, necessary PCC foundation with plastering to the Panel board, All out going feeders shall be connected by cable through suitable size gland plate / glands.& The various feeders shall be indicated by 50 mm size letters in synthetic enamel white paint. complete all as specified and as directed by Engr-in-Charge.

(b) Outgoing :- (i) MCCB 4P, 160A, 36 KA, with thermal magnetic: O/L & S/C protection , ICS= 100% ICU = 01 Nos. (ii) MCCB 4P, 125A, 25 KA, with thermal magnetic: O/L & S/C protection , ICS= 100% ICU = 02 Nos. (iii) MCCB 4P, 63A, 16 KA, with thermal magnetic: O/L & S/C protection , ICS= 100% ICU = 02 Nos.

Excavation in trenches in soft/loose soil n.exc 1.5m wide and n. exc 1.5m depth for laying of cable, errection of poles, stay and pipe line,and getting out complete all as specified and directed

Returning & filling including spreading, leveling watering and well ramming in layers n. exc 25 cm thick in any type of soil complete all as specified.

Removal of excavated soil to a distance n. exc 50 m above the starting point complete all as specified.

M&L fly ash old size bricks , straight or curved on plan , laid flat with width equal to length of brick , laid dry over electric cable for protection all as specified.

M & L for local sand coushioning with dry and clean over and under the cable for protection of cable , 80 mm sand laid before laying the cable 150 mm sand after laying the cable and filling the sand in cable duct of inside the sub station building complete all as directed

Dismantling the existing LT over head line (ACSR conductor) carefully any size from LT pole including disconnecting electric connection) complete all as specified & directed.

Dismantling/taking down carefully insulator any size and any type from existing LT lines complete all as specified and directed.

Dismantling of cross arms of MS channel or angle iron section with clamps etc. complete all as specified and directed.

Dismantling the existing stay assembly complete all as directed.

Supplying, installing, commissioing and testing of LT switchgear panel board ( Kiosk) of size not less than 600mmx600mmx500mm, IP-55 (outdoor type) , 415 Volts, 50 Hz, AC supply, three phase and neutral ( 4 wire) , 400 Amps coloured horizontal tinned Aluminium bus bars , factory made out of 3.15mm thick MS sheet structure mounted on rigid mild steel angle iron frame of 50mmx50mmx6mm with 400mm long extended legs grouting in PCC 1:2:4 type B1 of size 150mmx150mmx250mm , duly epoxy powder coated internally and externally with approved shade, rubber gasketted, hinged front double door and back openable doors with proper locking arrangements for dust and vermin proof ,complete including adjustable thermal and fixed magnetic release MCCB 4 pole, 200 Amps, 415V,36 KA,50 hz -01 No (incoming),suitable size cable allay, lugs , glands and making connections/ wiring with suitable size SC PVC insulated copper conductor cable all as specified.

Supplying, installing, commissioing and testing of LT switchgear panel board ( Kiosk) of size not less than 600mmx600mmx500mm, IP-55 (outdoor type) , 415 Volts, 50 Hz, AC supply, three phase and neutral ( 4 wire) , 200 Amps coloured horizontal tinned Aluminium bus bars , factory made out of 3.15mm thick MS sheet structure mounted on rigid mild steel angle iron frame of 50mmx50mmx6mm with 400mm long extended legs grouting in PCC 1:2:4 type B1 of size 150mmx150mmx250mm , duly epoxy powder coated internally and externally with approved shade, rubber gasketted, hinged front double door and back openable doors with proper locking arrangements for dust and vermin proof ,complete including adjustable thermal and fixed magnetic release MCCB 4 pole, 100 Amps, 415V,36 KA,50 hz -01 No (incoming),suitable size cable allay, lugs , glands and making connections/ wiring with suitable size SC PVC insulated copper conductor cable all as specified.

M&L earthing complete with galvanised steel earth plate electrode, 600 x600 x 6mm thick burried directly in the ground (earth pit not less than 3.25 mtr deep below ground level) with top edge of the plate not less than 1.5mtr below ground level connected to galvanised strip 25x4 mm size as earthing lead by means of bolts, nuts, check nuts and washers of GI up to test point, GI tubing 15 mm bore medium grade protection pipe, GI watering pipe 20mm bore light grade with funnel and wire mesh, charcoal, salt complete all as per SSR with PCC chamber, 50mm thick RCC cover in 1:2:4 type B-1 using 20mm graded stone aggregate reinforced with 8mm dia TMT bar @ 80mm c/c both way including earth work in any type of soil , removal of surplus soil to a distance n.exc 50m and connecting , testing on completion all as shown on electric plate No 03 of SSR -2009 Part I complete all as specified and directed.(Note: Excavation and earth work is deemed to be included in the rates quoted).

Material and labour for GI tubing light grade 100 mm bore for passing through cables, laid in treanches, under the floor, along the wall or along the pole with necessary clamps, nuts, bolts and washers etc. and making good disturbed surface of wall, floor etc complete all as specified and directed .

Material and labour for GI tubing light grade 40 mm bore for passing through cables, laid in treanches, under the floor, along the wall or along the pole with necessary clamps, nuts, bolts and washers etc. and making good disturbed surface of wall, floor etc complete all as specified and directed .

M & L for drilling suitable dia horizontal bore holes for insertion / laying of 50/100 mm bore GI tubing of any description below/under road surface/floors etc with using mechanical or manual devices as required at site including making good disturbed surface to match with the existing streta after laying pipes complete all as specified and directed

Supplying , intallation , commissioning and testing of Diesel engine driven fire pump set for fire fighting purpose horizontal end suction, centrifugal type confirming to IS- 12469 1988 with CI casing , bronze impeller and stainless steel shaft mounted on heavy duty bearings suitable for continuous operation with 'range of operation' 0 % to 150 % of rated capacity for 440 V , 3 phase, 50 Hz AC supply 70 m Head. 1620 LPM discharge and 1500 / 1800 RPM comprising of following details- (a) Horizontally mounted, single end suction type pump of cast iron body.Common bed plate of fabricated mild steel channel or cast iron type. (b) Common robust bed plate of fabricated out of mild steel channel of appropriate size with foundation including vibration damping arrangement fixed pad as per OEM recmondation . (c ) Suitably coupling between pump and engine including sheet metal coupling gravel.vibration clamping arrangement as required. with foundation bolts, anti vibration pads, washers etc. as per manufacturer's specifications and instructions. (d) The pump impeller shall be of bronze impeller and water cooled with mechanical seals, (e) Diesel engine developing suitable BHP for the above pump set with manual (f) Lead acid batteries of 12 V, 180 AH complete with bty charger -01 No. (g) Fuel tank of suitable capacity to run the engine for eight hours butnot less than 200 Ltrs complete with inlet and outlet connections, fuel filter, fuel pump, oil indication gauge, exhaust silencer, exhaust system of suitable dia. class `C' M.S. pipe including 50mm thick rock wool insulation and cladded with 22 gauge aluminium Sheet in an approved manner, fly wheel, air intake manifold, air cleaner, radiator, radiator fan, lub. oil pressure gauge, filter, cooling water temperature gauge and all as directed.

Supplying , installation,testing and commissioning of Fire pump electrically driven horizontal end Suction, centrifugal type confirming to IS- 12469 :1988 with CI Casing , bronze impeller and Stainless steel shaft mounted on heavy duty bearings Suitable for continuous operation with 'range of operation' 0 % to 150 % of suitable rated capacity for 440 V, 3 Phase 50 Hz to discharge 1620 LPM at 70 mtr head with comprising following details:- (a) Horizontally mounted, single end suction type pump of cast iron body. Common bed plate of fabricated mild steel channel or cast iron type. (b) Commomn robust bed plate of fabricated out of mild steel channel of appropriate size with foundation including vibration damping arrangment fixed pad as per OEM recommendation. (c) Suitably coupling between pump and electric motor including sheet metal coupling gravel. Vibration clamping arrangement as required with foundation bolts, anti vibration pads,washers etc as per manufacturer's speicifications and instructions. (d) The pump impelller shall be of bronze impeller and water cooled with mechanical seals. (e) Squirrel cage, TEFC induction motor suitable for 415 V, 3 phase having IP 55 protection and class 'B' insulation for the above pump and flexible coupling with the pump.

Supply,and fixing , of sluice valve of size 100 mm dia bore, class PN 1.6, cast iron body with forged brass spindle, non rising type, and case iron wheel head, both ends flanged, IS- 14846 marked complete with neoprene rubber gasket joint and nuts, bolts, (high tensile), washers, two nos. flanges welded with pipes etc. complete all as specified and directed.

Supply, laying & jointing MS ERW pipe 250mm dia (class C) ISI marked conforming to IS 3589 ( 1981) 6.0 mm thick including all fittings i.e. reducer, elbows, tees, flanges etc. below ground including, edge preparation, jointing by welding, providing two coats of coltar hot red paint over a coat of red oxide primer anti corrosion protection Laying the pipes in or out side the trenches in proper alignment, hydrostatic testing of the complete pipe work, disposal of surplus earth as directed, providing 1:2:4 type B-1 (using 20 mm graded stone aggregate) cement concrete thrust blocks of suitable size at bends and tees, completing the followings

Supply, laying & jointing MS ERW pipe 150mm dia (class C) ISI marked conferming to IS 3589 ( 1981) 6.0 mm thick including all fittings i.e. reducer, elbows, tees, flanges etc. below ground including, edge preparation, jointing by welding, providing two coats of coltar hot red paint over a coat of red oxide primer anti corrosion protection Laying the pipes in or out side the trenches in proper alignment, hydrostatic testing of the complete pipe work, disposal of surplus earth as directed, providing 1:2:4 type B-1 (using 20 mm graded stone aggregate) cement concrete thrust blocks of suitable size at bends and tees, completing the

Supply, laying & jointing MS ERW pipe 100mm dia (class C) ISI marked conferming to IS 3589 ( 1981) 6.0 mm thick including all fittings i.e. reducer, elbows, tees, flanges etc. below ground including, edge preparation, jointing by welding, providing two coats of coltar hot red paint over a coat of red oxide primer anti corrosion protection Laying the pipes in or out side the trenches in proper alignment, hydrostatic testing of the complete pipe work, disposal of surplus earth as directed, providing 1:2:4 type B-1 (using 20 mm graded stone aggregate) cement concrete thrust blocks of suitable size at bends and tees, completing the

Supply,and fixing , of sluice valve of size 150 mm dia bore, class PN 1.6, cast iron body with forged brass spindle, non rising type, and case iron wheel head, both ends flanged, IS- 14846 marked complete with neoprene rubber gasket joint and nuts, bolts, (high tensile), washers, two nos. flanges welded with pipes etc. complete all as specified and directed.

Supply & fixing of Non Return Valves ISI marked of size 150mm dia bore cast iron double flanged as per IS : 5312, part- I, suitable for pressure15 KG/cm2, including suitable size of nuts, bolts, gaskets and washers etc. complete including testing all as specified and directed.

Supply,and fixing , of stainer 'Y' type in suction pipe of size 150 mm dia bore, class PN 1.6, cast iron body with , both ends flanged, complete with neoprene rubber gasket joint and nuts, bolts, (high tensile), washers, two nos. flanges welded with pipes etc. complete all as specified and directed.

Supply,and fixing , of foot valve in suction pipe of size 150 mm dia bore, class PN 1.6, cast iron body one end flanged, complete with neoprene rubber gasket joint and nuts, bolts, (high tensile), washers, two nos. flanges welded with pipes etc. complete all as specified and directed.

Supply and fixing of foot valve in suction pipe of size 100 mm dia bore, class PN 1.6, cast iron body one end flaged complete with neoprene rubber gasket joint and nuts, bolts, (high tensile), washers, two nos. flanges welded with pipes etc. complete all as specified and directed.

Supply & fixing of Non Return Valves ISI marked of size 100mm dia bore cast iron double flanged as per IS : 5312, part- I, suitable for pressure15 KG/cm2, including suitable size of nuts, bolts, gaskets and washers etc. complete including testing all as specified and directed.

Supply,and fixing , of stainer 'Y' type in suction pipe of size 100 mm dia bore, class PN 1.6, cast iron body with , both ends flanged, complete with neoprene rubber gasket joint and nuts, bolts, (high tensile), washers, two nos. flanges welded with pipes etc. complete all as specified and directed.

Material and labour for Hose box to keep 02 Nos of hoses made out of 18 gauge MS Sheet of size 800mm X 600mm X 250mm with double door with 4 mm thick glasses and door frame made of 16 gauge MS sheet painted with two coat of red paint over a coat of red oxide primer and writting 'FIRE' out side the door with white paint complete all as specified and directed .

Material and labour for hose real drum with RRL ( Reinforced rubber lined ) synthetic yarn hose pipe 15 mtr long confirming to IS-363 including male and female brass connector at both end of size 63mm bore fixing in hose real box with welding moveable type heavy duty with red paint complete all as specified and directed.

supply and fix branch pipe brass nozzle 63mm instantaneous inlet, made threaded outlet, 15mm bore nozzle long complete all as specified and directed

Supply and fixing Gun metal double headed hydrant valves with flanged inlet with 63 mm dia oblique female instantaneous pattern outlet of gun metal complete with 80 mm dia butterfly valve, rubber blank cap and chain wing type plug with suitable size bolts, nuts, washers and gaskets. Landing valves shall be conforming to IS : 5290 specification.

Supply , laying and testing of Ductile Iron pipe with spigot and socket ends centifugally cast iron class KA 9 in any length laid in trenches of 150 mm dia

M & L DI/CI Specials class B as per IS such as bends, tappers,any type branches cross all sockets and spigot collar caps and plug up to 150mm bore all as specified and as directed

M&L for earthing complete with galvanized steel earth plate electrode 60cm x 60 cm x 6 mm thick buried directly in ground earth pit not less than 2.25 mtr deep below ground level with top edge of the plate not less than 1.5 mtr below ground level connected to galvanized earth strip 25x4 mm by means of bolts, nuts, check nuts and washers of GI or steel surrounded with adequate quality of charcoal dust mixed with salt on all side of earth plate including complete earthwork PCC 1:2:4 chamber and RCC 1:2:4 cover all as shown in electrical plate No 5 and all as specified and directed Note:- If desired earth resitance not found, earthing shall be redone by the copntractor at no extra cost to the department.

Supply and laying or fixing or passing through pipe, XLPE insulated , armoured heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area 25 Sqmm 4 Core including connecting with suitable size of aluminium lugs, nuts and bolts laid in trenches complete all as specified and directed .

Supply, installation, testing and commissioning of LT panel board made out of CRCA sheet steel 2.0mm thick fabricated cubical type Electrical Control Panel for fire fighting pumps floor mounting, dust & vermin proof, front operated construction, enclosure class - IP 52, Powder coated paint complete with top/bottom removable gland plates, as required, having 04 Nos of lugs of angle iron 40x40x6mm thick 0.5 mtr long grauted in PCC 1:2:4 type B1, cable glands, hinged and locking arrangement to doors iincluding internal wiring with having the following :-

(a) MCCB 63 Amp FP 415 Volt 50 Hz fixed type thermal relay.16 KA-01 No. (b) Supply and fix fully automatic, star delta starter of motor capacity 30 HP, 3 phase, 415 Volt complete with contactor , relay setting for protection against UV/ OV, short circuit.-01 No. (c ) Volt Meter Digital, square type 600 volt -01 No. (d) Amp meter digital square type 100 Amps -01 No. (e) Indicator lamp three phase RYB-01 Set of three.

Supply and fixing pressure gauge 4" dial type of range 0-14 Kg/ Sqcm complete with threaded in existing pipe and working satisfactory all as specified and directed.

Supply and fixing air cushion tant with relief valve of size 300mm dia fixed with suction line with 80 mm dia MS pipe heavy duty including painting of two coat of red paint over a coat of red oxiide complete all as specified and directed.

M&L for surface dressing n exc 15cm deep in soft/loose soil complete all as specified and directed

Excavating in post holes (or similar holes) each n.exc. 0.5 cum, getting out in hard dense soil returning, filling in and ramming earth or broken rubble mixed with earth around, in layers, n.exc. 25cm, watering and removing surplus soil to a distance n.exc. 50m and making good surface

M&L cement concrete type D-2 1:4:8 (40mm graded aggregate) as in foundation filling and mass concrete

M&L for brick work with fly ash bricks ( old size) straight or curved in plan exc 6 m mean radius , built in CM 1:6 Comlete ass as specified and directed

M&L rendering 15 mm thick on fair faces of brick work or cocrete surfaces in cm 1:4 complete including water proofing compound (Nore WPC will be measured and paid separatly)

Supply only intergal water proofing conpound Make:- sapseal, JK, Sikka or equivalent as approved by GE

S&F rolled trusses ( framed ), trussed purlins, crane and fastening feavy bracket framing ( bem, tee,anglechannel or flat sections) including distance pieces cleates etc confirming to Fe 410-W(Gde E-250 Quality)

M & L for preparation of new or previously un treated steel and iron surfaces over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide or zinc chrome on steel and iron surfaces all as specified and directed.

S&F pre painted galvalume aluminium zinc coated GI based corrugated steel sheet 0.50 mm thick of an colour having a tensile strength of 550 Mpa as in roof covering / clading to wall fixed with self tapping screws as specified

S&F MS wind tie for roof including securing bolte etc complete all as specified.

M&L hardcore of exc. 63 mm but n,exc 100 mm thick deposited spread and levelled in layers n exc 15 mm thick watered and rolled /rammedto a true surfaces complete all as specified.

M&L 100 mm thick cement concrete type D-2 1:4:8 (40mm graded aggregate) as in sub base of floor complete all as specified.

M&L 40 mm thick cement concrete type B 1:2:4 (20 mm graded aggregate) as in finishing surface complete all as specified.

M&L for preparing new plastered of walls and applying two coats of cement base paint all as specified and directed by EIC

M&L cement concrete Type C2 ( 1:3:6 ) ( 40 mm graded aggregate as in foundation and mass concrete compete all as specified.

S&F rolled sections as in framing for clading and the like fixed with angle cleats and connecting plates conforming to Fe 410-W ( Gde E- 250 quality A) compete all as specified.

S&F plates (plain or chequered ) channels square cut or notched ( ordinary and counter shunk ) forming holes without any attachment conforming to Fe 410-W ( Gde E- 250 quality A) compete all as specified.

S&F 1000 ltr capacity water tanks rotational moulded polyethylene water storage tanks ( cylindrical vertical with closed top ) hoisted and fixed in position 3 layer including 20 mm PVC ball valve.compete all as specified.

S&F 20 mm bore medium grade GI pipes galvanised with all fitting laid in trenched compete all as specified.

S&F 20 mm gate valve with iron wheel head screwed both ends for iron pipe line compete all as specified.

Supply and fix Reverse Osmosis(RO) Plant Commercial plant 100-150LPH flow rate, Stainless steel structure, fully automatic for water purification with the following components:- 1. Raw water pump 2. Multigrade Filter 3. Activated Carbon Filter 4. Antiscalent dosing pump. 5. Micron filter 6. Membrane housing 7.RO Membrane 8. Control Instrument. 9. Control Panel 10. Dosing Tank 11. 500 Ltrs Storage Tank. Note:-RO Rates included cost of raw water/clear water storage tank, softener, plumbing and electrical wks. Feed water characterstics:

mohanlal gupta (BID ID -3101150)

SIYA ASSOCIATES (BID ID -3113806)