PROVISION OF ENTRY/EXIT GATE, SENTRY POST, TOILET BLOCK, SHED, CONNECTING PATHWAYS AND ALLIED INFRA NEAR MH OFFICERS MESS AT ZONE-III UNDER GE(S) JAIPUR AT MIL STN JAIPUR

Amount

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft / loose soil complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5m depth for foundation etc or for shafts, wells cesspits manholes pier holes etc not exceeding 10 sqm on plan and in soft /loose soil etc complete all as specified and directed.

Returning, filing in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft/loose soil etc complete all as specified and directed

Removal of excavated materials (soil) not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting points etc complete all as specified and directed.

M&L for sand filling under floor or in foundations including gently punned as in cushioning to cable and for foundation in floor complete all as specified and directed. Note:- Punned thickness of sand shall be measured and paid.

M&L for earth filling including spreading and levelling in layer not exceeding 25 cm thick including watering and well ramming complete all as specified and directed.

M&L for broken stone or boulders hardcore of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

M&L for RCC (design mix) M-25 using 20 mm graded stone aggregates as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under reamed piles and mass concrete complete all as specified and directed . Note - Reinforcement and form work shall be measured and paid separately.

M&L for RCC (design mix) M-25 using 20 mm graded stone aggregates as in Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses complete all as specified and directed . Note - Reinforcement and form work shall be measured and paid separately.

M&L for RCC (design mix) M-25 using 20 mm graded stone aggregates as in slab supported on wall, beam and column in floors, roofs, landings, balconies, canopies and in shelves and similar work complete all as specified and directed. Note - Reinforcement and form work shall be measured and paid separately.

M&L for RCC (design mix) M-25 using 20 mm graded stone aggregates as in beam, cantilevers, bressummers, lintels over 1.5 m span and similar work complete all as specified and directed. Note - Reinforcement and form work shall be measured and paid separately.

M&L for RCC (design mix) M-25 using 20 mm graded stone aggregates as in columns, pillars, piers, posts and struts and similar work complete all as specified and directed. Note - Reinforcement and form work shall be measured and paid separately.

M&L brick work using old size sub class 'B' bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for brick protection cover to the under ground cable (with old size sub class 'B' bricks) with width equal to length of brick laid dry and flat abutting each other with gaps between adjacent brick not exceeding 10 mm all as specified and directed.

S&F Dholpur stone precast hut of size 1.20x1.20x1.70m dome structure (as per sample kept with engineer in charge) inlcuding fixing on brick/concrete walls with adhesive complete all as specified and directed. Note :- Stone adhesive of Asian/Roff/Weber(Saint Gobin) shall be used.

S&F 10mm thick PVC false ceiling fixed to metal framework suspended from temporary roof with the help of GI wires of 6 to 8 mm in wooden or any other pattern complete including filling of joints and gaps with silicon of same colour as of ceiling complete all as specified and directed. all as specified and directed.

S&F Dholpur stone precast projected members as on wall of size 1.20 x 1.20 x 0.30 m (as per sample kept with engineer in charge) inlcuding fixing on brick / concrete walls with adhesive complete all as specified and directed. Note :- Stone adhesive of Asian/Roff/Weber(Saint Gobin) shall be used.

S&F Dholpur stone minarets of size 0.30 m x 0.30 m x .10 m (as per sample kept with engineer in charge) inlcuding fixing on brick/concrete walls with adhesive complete all as specified and directed. Note :- Stone adhesive of Asian / Roff / Weber (Saint Gobin) shall be used.

M&L for 16 to 18mm thick Dholpur stone cladding gang saw cut with machine cut edges, uniform colour of each stone size exceeding 0.5 sqm area fixed with and including one number SS clamps (grade -202) of flat-30mm X 2 mm, 150 mm long made to shape in each slab, making V groove at top and bottom of stone and drilling hole for hold fastener, polishing, rubbing & including silicon treatment complete all as specified and directed.

M&L 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including screed bed 15 mm thick in CM 1:4 complete all as specified & directed.

M&L for Form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams etc and similar work, vertical or to batter for rough finished flat concrete surfaces complete all as specified and directed.

M&L for Form work to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter for rough finished flat concrete surfacescomplete all as specified and directed.

M&L for form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200 mm thick (horizontal or sloping) for rough finished flat surface of concrete complete all as specified and directed

M&L for form work to sides and soffits of floor or roof beam, beam hauchings, girders, bressummers, lintels, cantilevers, shelves, for flat rough finished concrete surfaces complete all as specified and directed.

M&L for Form work to sides of pillars, posts, struts, piers, columns and stanchions for square, rectangular or polygonal rough finished concrete surface complete all as specified and directed

M&L for Form work to edges of concrete flats, treads breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roof and sides of bands in walls, horizontal or sloping and similar work for fair finished concrete surface exc 10 cm but not exc 20 cm wide complete all as specified and directed.

S&F 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F aluminium, anodised, barrel tower bolts of extruded section 200 mm long complete all as specified and directed.

S&F aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy of 300 mm length of bolt complete all as specified and directed.

S&F butt hinges, medium weight, cold rolled mild steel 100 mm long complete all as specified and directed.

S&F extruded aluminium alloy handles fabricated type anodised of 150 mm size complete all as specified and directed.

M&L for mild steel TMT bar 10 mm dia and over cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bar 5 mm dia and over upto and including 10mm dia as in stirrups, spacers & binders cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F rolled mild steel section in framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc, complete drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging of grade Fe 290(Gde E-165) complete all as specified and directed.

S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed.

S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay complete with glazing bars, dovetailed or welded complete all as specified and directed.

M&L for applying fibre reinforced, single component, elastomeric liquid applied water proofing coating in white colour, anti-fungal, anti-algae, resistance to water and ageing, excellent UV resistant having Solar Reflective Index more than 105, with PU hybrid polymers and reinforcing acrylic fibers, elongation greater than 300% and applied in three layer complete all as follow :- (a) Preparation of surface by cleaning and removing loose particles then apply first coat of liquid water proofing after diluting as per manufacture instruction as a primer and allow the surface to dry for minimum 10 to12 hours complete all as specified and directed. (b) Apply second coat of liquid water proofing without dilution on the primed surface and allow time to dry the surface for minimum 10 to12 hours complete all as specified and directed. (c) Apply third coatof liquid water proofing without dilution over the second coat and allow minimum 48 hour complete all as specified and directed. Note : (i) Work shall be carried out by authorised applicator of manufacturer only and contractor will submit MoU with authorised applicator of manufacturer before execution of work. (ii) Material incorported in the work shall be calculated as per site requirement and full quantity of material shall be brought at site before execution of work. (iii) Necessary gurantee for 05 years shall be submitted by the contractor. Make :- Berger-HS Roof Kool & Seal, STP-Shali Urethane (R) BTD Plus, Asian - Smart care Damp Proof Ultra or equivalent make as approved by GE.

S&F 6mm thick polycarbonate sheet transparent in nature of approved colour shade fixed with screw as in roof coverings complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof overing/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for machine cut kota stone slab flooring mirror finished 20-25 mm thick (each slab not less than 0.25 sqm) over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing on treads of step and landing of stair including screed bed 20 mm thick in CM 1:4 complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in sub base flooring 25 mm thick surface finished even and fair without using extra cement complete all as specified and directed.

M&L for full body vitrified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished area of each tiles exceeding 0.42 sqm but not exceeding 1.0 sqm in floors etc. set and jointed with epoxy grounting with minimum 3mm spacer and including screed bed or bedding layer 15 mm thick in CM 1:6 complete all as specified and directed.

M&L for glazed digital ceramic coloured tiles in vertical surface 600x 1200x 10 mm thick, (digital tile ) as dado etc laid in concept /pattern using highlighters set and jointed in neat cement adhessive and pointed in white or coloured cement to match surface of tiles over and including rendering 10 mm thick in CM 1:4 complete all as specified and direct

M&L for machine cut kota stone slab mirror finished 20-25 mm thick (each slab not less than 0.25 sqm) in riser of step ,skirting, dado and pillar over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including rendering 10 mm thick in CM 1:4 complete all as specified and directed.

M&L for 75 mm thick Cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate as in sub base complete all as specified and directed.

M&L for 100 mm thick Cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base complete all as specified and directed.

M&L (except interlocking paver block) for interlocking paver block, any shape and size of 60 mm thickness, by vibratory compaction, cutting paver blocks in required size and pattern, filling joints with sand including sand cushing 50 mm thick and sweep out surplus sand complete all as specified and directed. Note : (1) Old paver block obtained from dismantle shall be used. (2) Sand cushioning shall be measured and paid separetely.

M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3, including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

M&L for providing and laying 60 mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

M&L for rendering on fair faces of brick work or concrete surface of wall 15 mm thick in CM 1:4 and to be finished even and smooth with out using extra cement complete all as specified and directed

M&L for rendering 10 mm thick in CM 1:6 on fair faces of brick or concrete surface of wall and finished even and smooth with out using extra cement complete all as specified and directed.

M&L for rendering 05 mm thick in CM 1:3 on ceiling surface and finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of new surface of ceiling of any description and applying two coats of oil bound distemper (OBD) over a coat of chalk whiting on plastered surfaces preparatory to distempering over and including 1 mm thick wall putty all as specified and directed.

M&L for preparation of new surface of wall of any description and applying two coats of oil bound distemper (OBD) over a coat of alkali-resistant priming paint over and including 1 mm thick wall putty all as specified and directed.

M&L for preparation of new surface of walls of any description with a coat of 1 mm thick wall putty and applying two coats of acrylic emulsion exterior grade weather proof paint over a coat of primer complete all as specified and directed. Make for Acrylic Emulsion Paint : Apex Ultima of Asian Paint / WeatherShield Max of Dulux / WeatherCoat Anti Dust of Berger or equivalent make as approved by GE. Note :- Acrylic Emulsion Paint shall be carried out as specified in clause 15.17 of SSR Part-I including all necessary arrangement such as scaffolding / working plateform for execution of work upto four storey building etc.

S&F 4.8 mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane, complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of steel of any description, over 10cm in width or girth and apply two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F bolt touch-free infrared hand dryer with 1150W rated power & carbon brush motor complete all as specified and directed. Make:- Jaquar cat part No. HDR-SSF-AK2803D or equivalent model of make Kohler / Grohe / Roca as approved by GE.

S&F Vitreous China bowl urinal flat back, size of 385 x 325 x 635 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and directed. Make:- Jaquar cat part No. URS-WHT-13253N or equivalent model of make Kohler / Grohe as approved by GE.

S&F Paper Towel Dispenser of stainless steel (AISI-304) with capacity to accommodate upto 400 towel C-fold or Z-fold, wall mounted type complete all as specified and directed. Make: Jaquar cat part No. PTD-SAP-DT0106CSN or equivalent model of make Roca / Dolphy as approved by GE.

S&F in bib taps 2-in-1 cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule fancy type of 15 mm bore dia of pipe complete all as specified and directed. Make : Jaquar CAT Part No KUP-CHR-35041PM / Kohler CAT Part No 25432IN-4-CP / Grohe CAT Part No 20281000 or equivalent as approved by GE.

S&F snow white colour vitreous china, rimless Wall Hung WC with UF Soft Close Seat Cover, Hinges, Accessories Set, Single Piece Slim concealed cistern with floor mounten frame, installation kit with twin flush control plate including fixing as per manufacturer instructions complete all as specified and as directed. Make : Jaquar CAT Part No LAS-WHT-91953BIUFSM / Roca CAT Part No RS34668900C / Kohler CAT Part No SKU: K-20217IN-S-0 or equivalent make as approved by GE.

S&F waste coupling of brass CP for 32 mm bore dia of pipe half or full threaded with long shank complete all as specified and directed.

S&F for 15mm bore dia of pipe brass CP fancy type ,with crutch butter fly handle , wash hand basin mixer for mixing hot & cold water screwed down for iron pipe complete all as specified and directed. Make : Jaquar CAT Part No OPP-CHR-15011BPM / Kohler CAT Part No 22534IN-4-CP / Grohe CAT Part No 32851000 or equivalent as approved by GE.

S&F 450 x 800 x 250 mm vitreous china wash hand basin floating type mounted on wall excluding taps, waste, chain & plug and porcelene stopper but including brackets /fastners, cutting for and pinning in ends of brackets but inclusive fixing of CP waste coupling/grating and waste pipe/CP bottle trap. Note: Waste pipe / CP bottle trap and CP waste coupling / grating shall be measured and paid separately.

S&F 50 mm thick PUF ( Polyurethane Foam) insulated sandwich panel with pre-coated GI Sheet not less than 0.5 mm thick on both sides , having a total density of not less than 40 Kg per cubic meter, including all necessary fixing arrangement complete all as specified and directed.

S&F toilet cubicles of size 2125 mm depth x 900 mm width having a clear door opening of 750 mm made with 12 mm thick high pressure laminate (HPL) compact board , exterior grade , moisture resistant , termite proof , scratch resistant and antibacterial surface finish to be fixed on floor, including all necessary hardware such as hinges , locks, handle and sliding bolt, cubicle panels anchored securely to floor, wall and ceiling as required using stainless steel brackets and fasteners or as per manufacture instruction complete specified and directed.

S&F rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) 1000 litre capacity hoisted and fixed in position complete all as specified and directed

M&L for Double Wall Corrugated (DWC) pipe of class SN-4, IS-16098 (part-II) of 200mm bore (internal), laid to slope in trenches, jointed complete with coupler, bends, Tee, reducers etc and tested complete all as specified and directed. Make : Ultra plus of Supreme / Corfit of Prince / D-Rex of Astral or equivalent as approved by GE.

M&L for PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors of 75 mm bore of pipe etc complete all as specified and directed.

M&L for PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors of 110 mm bore of pipe etc complete all as specified and directed.

M&L for PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls of 75 mm bore of pipe etc complete all as specified and directed.

S&F PVC (SWR) bends any radius of 75 mm bore without access door complete all as specified and directed.

S&F PVC (SWR) bends any radius of 110 mm bore without access door complete all as specified and directed.

M&L PVC (SWR) vent cowl 75 mm complete all as specified and directed.

M&L PVC (SWR) floor trap of diameter of outlet 75 mm, plain with grating including jointing with solvent cement complete all as specified and directed

M&L PVC (SWR) gully trap 125/110 mm setting and jointing with solvent cement complete all as specified and directed

M&L for cutting cast iron/ductile iron pipe and reducing to required length in position for insertion of new tees, branches etc for 80 mm bore dia of pipe complete all as specified and directed .

S&F GI tubes medium grade with all fittings laid in trenches of 25 mm bore of pipe complete all as specified and directed.

S&F 16 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls / ceiling or laying in floors complete all as specified.

S&F 20 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls / ceiling or laying in floors complete all as specified.

S&F Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe of 20 mm bore dia of pipe complete all as specified and directed.

S&F Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe of 25 mm bore dia of pipe complete all as specified and directed.

S&F ball valves for 20 mm bore dia of pipe high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight 210 gms) complete all as specified and directed.

S&F PVC connection 15 mm size bore with PTMT nuts of length 450 mm complete all as specified and directed.

M&L for cement concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid & tested for 100 mm bore of pipe with cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate complete all as specified and directed.

M&L for cement concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid & tested for 200 mm bore of pipe with cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate complete all as specified and directed.

M&L for cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required for 200/225 mm dia of pipe complete all as specified and directed.

M&L toilet paper holder , of stainless steel with flat recessed type, chromium plated, fixed to walls with chromium plated (CP) brass screws complete all as specified and directed. Make:- Jaquar CAT Part No. CPA-CHR-1151 / Grohe Cat Part No. 40367000 / Kohler cat Part No. K-5633IN-CP or equivalent model of make as approved by GE.

S&F sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed. Make:- Jaquar Cat Part No. CPA-CHR-1171 / Grohe Cat Part No. 407990CI / Kohler cat Part No. K-12158 or equivalent model of make as approved by GE.

S&F health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed. Make : Jaquar / Hindware / Cera or equivalent as approved by GE.

S&F chromium plated spreader for big urinal with CP pipe 15 mm dia with auto closing system complete all as specified and directed.

S&F angle stop valve, fancy type chromium plated cast copper alloy, for 15 mm bore dia of pipe screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and directed. Make : Jaquar CAT Part No KUP-CHR-35053PM / Hindware CAT part No. F320006 / Cera CAT Part No F1018201 or equivalent as approved by GE.

S&F for 32 mm bore brass chromium plated bottle trap for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and directed. Make:- Jaquar Cat part No. ALD-CHR-769L300x190 / Grohe Cat Part No. 28920000 / Kohler cat Part No. K-9033-CP or equivalent as approved by GE.

S&F liquid Push Button Soap Dispenser of brass fixed with and including chromium plated brass screws complete all as specified and directed. Make : Jaquar CAT Part No SDR-WHT-DJ0010FN or equivalent model of make Kholer / Roca / Grohe as approved by GE.

M&L in repair for round shape 15 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F ceiling rose 3 phase, PVC / polycarbonate, isolated body complete all as specified and directed.

M&L for point wiring complete with 1.5 Sqmm single core (Phase - Red, Neutral - Black) PVC insulated and unsheathed multi stranded copper conductor FRLS cable of 1100 V grade PVC insulated and unsheathed cable inclosed in and including concealed PVC conduit 20 mm dia medium grade with all accessories ISI marked, including MS sunken box / modular metal flush box of thickness not less than 1.2 mm, cover with 3 mm thick phenolic laminated white sheet cover for mounting fitting like switches, sockets fan regulators etc. including 1.5 Sqmm single core (Green colour) PVC insulated unsheathed copper earth continuity conductor FRLS cable 1100 V grade as continuous earth wire for one light / fan / bell point controlled by one, one way switch. Note :- (i) The Switch / Socket accessories shall be measure and paid separately. (ii) The cost of MS sunken box & cover plate of size as required at site and cutting chases in stone / brick masonry and making good disturbed surfaces using CM 1:3 shall deemed to be included in quoted rate.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 1.5 Sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 Sqmm (Green), concealed in wall and drawn into and including rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and terminated in MS sunken box modular metal flush box of thickness not less than 1.2 mm, cover with 3 mm thick phenolic laminated white sheet cover for mounting switches, sockets, fan regulator as required for one 3 pin socket outlet 5 Amps on the same board with other switches, complete all as specified and as directed.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 4.0 Sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 4.0 Sqmm (Green), concealed in wall, drawn into and including rigid non metallic PVC conduit medium grade not less than 25 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and terminated in MS Sunken box / modular metal flush box of thickness not less than 1.2 mm, cover with 3 mm thick phenolic laminated white sheet cover for mounting switches, sockets, fan regulator as required for 3 Pin 15 Amps socket outlet on independent board, complete all as specified and directed. Note :- (i) The Switch / Socket accessories shall be measure and paid separately. (ii) The cost of MS sunken box & cover plate of size as required at site and cutting chases in stone / brick masonary and making good disturbed surfaces using CM 1:3 shall deemed to be included in quoted rate.

M&L for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 25 sq. mm 4 core complete all as specified and directed. Note:- Excavation,earth work,sand,brick and protection pipe shall be measured and paid seperately.

M&L for earthing complete with galvanized steel earth plate 600x600x6mm thick, buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 m below normal ground level, connected to GI wire 4 mm dia as earthing lead by means of bolts, nuts, check nuts & washers of galvanized iron or steel besides building at all joints including excavation and earth work, GI pipe light grade 15mm bore for protection of GI wire from earth electrode, supply and laying charcoal dust, common salt, PCC (1:3:6) type B-1 using 20mm graded stone aggregate for chamber and MS angle iron frame 40x40x3mm and RCC cover 40 mm thick (1:2:4) type B-1 using 20 mm graded stone aggregate Reinforced with 6 mm dia round bars @ 75 mm C/C both ways with MS handle 12 mm dia, PGI funnel and wire mesh, 20 mm bore GI Pipe medium grade for watering complete all as shown in electrical plate No 3 of SSR Part-I(2009) and connected to earth test point including testing complete all as specified and directed. Note :- 1. PCC Chammer shall be constructed atleast 2.5 metre away form the earth electrode of the earth pit and pipe for watering shall be provided in slanting manner. 2. GI wire and protection pipe upto 7.5 meter from the earth plate electrode is deemed to be included in quoted rate. 3. Excavation for earthing to be done manually and Earth resistance below 3 Ohm should be obtained after measurement for every pit.

S&F electric water heater (Geyser), storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostat, NRV, connection piece etc. complete all as specified and directed. Note:- Connection with geyser inlet and outlet with 15mm bore GI pipe including PVC pipe is included in the quoted rate.

M&L for post top lantern LED type 40 watt, 230 volts AC outdoor type with decorative post top for 360 degree indirect light IP 65 protection with impact and corrosion resistant complete with driver and lamp complete all as specified and directed. Note : The quoted rate include the cost of assembling of the complete fitting and its testing before and after mounting or erection etc. for proper functioning.

S&F LED light fitting 1x20 W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F Modular Switch one way 6 A, 1 module complete all as specified and directed.

S&F modular switch 1 way 16A, 1 module complete all as specified and directed.

S&F Modular Socket, 6A - 2/3 pin combined, 2 module complete all as specified and directed.

S&F modular socket 6A/16A - 2/3 pin combined 2 module complete all as specified and directed.

S&F white cover plate with frame, 3 module complete all as specified and directed.

S&F white cover plate with frame, 8 module complete all as specified and directed.

S&F sheet metal enclosure with socket plug top and MCBs single pole and neutral enclosure with a two pin and earth plug and socket with one single pole MCB of capacity 20 Amps complete all as directed.

S&F sheet metal enclosure factory fabricated for MCB distribution board SPN double door type concealed in wall 240 Volt 8 way IP-42 protection with 200 amp rated bus bar complete all as specified and directed.

S&F exhaust fan, made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper winding of sweep of size 250mm complete all as specified and directed.

S&F amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of SPN and 40 to 63 Amp current carrying capacity complete with connection testing and commissioning all as specified and directed.

S&F amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of Single Pole and 06 to 32 Amp current carrying capacity complete with connection testing and commissioning all as specified and directed.

S&F wall mounted fan, complete with three blade, copper motor, 230 V, 50 to 60 watt, 400mm sweep, with 70CMM air delivery rated, fixing accessories complete all as specified and directed.

S&F PVC blanking plate one module complete all as specified and directed.

V S CONSTRUCTION (BID ID -3471012)