Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹1.1 CrAccepted-AOC | ₹1.1 Cr | L1 | Accepted-AOC L-1 |
| 2 | L2₹1.1 CrRejected-Finance | ₹1.1 Cr | L2 | Rejected-Finance L2 |
| 3 | L3₹1.1 CrRejected-Finance | ₹1.1 Cr | L3 | Rejected-Finance L3 |
| Sl No | Description | Qty | Unit | N K Enterprises L3 | M/S UNIVERSAL TELECOM L2 | RAKESH JAISWAL L1 |
|---|---|---|---|---|---|---|
| 1.00 | Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50 M. including all lifts, levelling, ramming the foudation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/l. | 368.69 | cum | 150 ₹55,303.50 | 124.7 ₹45,975.64 | 120.58 ₹44,456.64 |
| 2.00 | Extra for earth work in hard soil as per specification and direction of E/I (Vide classification of soil item_B) | 368.69 | cum | 15 ₹5,530.35 | 12.74 ₹4,697.11 | 12.32 ₹4,542.26 |
| 3.00 | Earth Filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50Mand lift of 1.5M all complete as per building specification and direction of E/I. (mode of measurement compacted volume) | 1,454.13 | cum | 55 ₹79,977.15 | 45.41 ₹66,032.04 | 43.9 ₹63,836.31 |
| 4.00 | Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including' cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement complacted volume). | 87.66 | cum | 589 ₹51,633.51 | 484.22 ₹42,448.18 | 468.19 ₹41,042.94 |
| 5.00 | Providing designation 75B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I. | 579.31 | sqm | 200 ₹1.2 L | 271.34 ₹1.6 L | 262.36 ₹1.5 L |
| 6.00 | Providing randam rubble stone masonry in CM (1:6) in foundation and plinth with hammer dressed stone of less than 0.03 M3 in volume and clean coarse sand of F.M. 2 to 2.5 including cost of screening raking out joints to 20 mm depth, curing taxes and royalty all complete as per building specification and direction of E/I. | 108.73 | cum | 1,800 ₹2.0 L | 2,070.59 ₹2.3 L | 2,002.02 ₹2.2 L |
| 7.00 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering .all work up to plinth level: 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) | 44.3 | cum | 2,700 ₹1.2 L | 3,081.6 ₹1.4 L | 2,979.55 ₹1.3 L |
| 8.00 | Providing designation 75B brick work in C.M (1:6 ) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I. | 104.5 | cum | 4,300 ₹4.5 L | 4,197.57 ₹4.4 L | 4,058.57 ₹4.2 L |
| 9.00 | Providing designation 75 B brick work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including, providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I. | 93.15 | cum | 4,300 ₹4.0 L | 4,307.49 ₹4.0 L | 4,164.85 ₹3.9 L |
| 10.00 | Providing designation 125 mm thick reinforced designation 75A brick work in CM (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 25 including the cost of screening, carriage of materials, scaffolding , raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/I. | 163.24 | Sqm | 600 ₹97,944 | 586.06 ₹95,668.43 | 566.65 ₹92,499.95 |
Tender Value
₹1.3 Cr
EMD Value
₹2.7 L
Closing Date
25 Aug 2025, 11:00 amClosed
E.E., BCD, Building Division, Simdega
E.E., BCD, Building Division, Simdega
Construction of Type-A (District Level) Akhra, Simdega, Jharkhand
2025_BCD_104016_1
07/2025-26/EE/BCD/BD,SIMDEGA
Open Tender
Civil Works - Buildings
270 days
Simdega
Please refer Tender documents.
2 documents required · 2 mandatory
₹10,000
₹2.7 L
10 Jan 2026
18 Aug 2025
26 Aug 2025
18 Aug 2025
25 Aug 2025
18 Aug 2025
Amount
Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50 M. including all lifts, levelling, ramming the foudation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/l.
Extra for earth work in hard soil as per specification and direction of E/I (Vide classification of soil item_B)
Earth Filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50Mand lift of 1.5M all complete as per building specification and direction of E/I. (mode of measurement compacted volume)
Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including' cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement complacted volume).
Providing designation 75B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I.
Providing randam rubble stone masonry in CM (1:6) in foundation and plinth with hammer dressed stone of less than 0.03 M3 in volume and clean coarse sand of F.M. 2 to 2.5 including cost of screening raking out joints to 20 mm depth, curing taxes and royalty all complete as per building specification and direction of E/I.
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering .all work up to plinth level: 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)
Providing designation 75B brick work in C.M (1:6 ) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I.
Providing designation 75 B brick work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including, providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I.
Providing designation 125 mm thick reinforced designation 75A brick work in CM (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 25 including the cost of screening, carriage of materials, scaffolding , raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/I.
Providing randam rubble stone masonry in CM (1:6) in superstructureincluding cost of screening of materials scaffolding raking out joints to 20 mm depth, curing taxes and royalty all complete as per building specification and direction of E/I.
Providing and laying in position specified grade of reinforced cement concrete,excluding the cost of centering,shuttering ,finising and reinforcement- all work up to plinth level,1:1.5:3(1 cement : 2 coarse sand : 4 graded stone aggregate 20mm normal size).
Reinforced cement concrete work min wall (any thikness), including attached pilasters,buttresses,plint and string courses,fillets,column,pillars,piers,abutments,posts and struts etc. above plint level up to floor five level, excluding cost of centering, shuttering ,finishing and renforcement: 1:1.5:3( 1 cement : 1.5 coarse sand (zone-III) :3 grade stone aggregate 20 mm normal size).
Reinforced cement concrete work in beam, suspended floors,roofs having slope up to150 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floors five level, excluding the coast of centering, shuttering, finishing and reinforcement ,with 1:1.5:3(1 cement :1.5 coarse sand (zone III) :3 graded stone aggregate 20 mm normal size).
Centering and shuttering including strutting,propping etc.and removel of form for. Foundation
Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.
Centering and shuttering including strutting,propping etc.and removel of form for Column
Centering and shuttering including strutting,propping etc.and removel of form for Plinth beam
wash basin slab
Roof slab
Providing TMT reinforcement of 8mm dia rods as per approved -do-TMT Fe 500(only valid for tata,sail,jspl,electrosteel,bokaro and vizag)
Providing TMT reinforcement of 10mm, dia rods as per approved -do-TMT Fe 500(only valid for tata,sail,jspl,electrosteel,bokaro and vizag)
Providing TMT reinforcement of 12mm,16mm & 20mm dia rods as per approved -do-TMT Fe 500(only valid for tata,sail,jspl,electrosteel,bokaro and vizag)
Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.
Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.
Water proofing for Old and New Roof Slab Providing and laying water proofing treatment on roof slab by applying two Component, factory designed, ready to use, acrylic modified flexible material applied wth brush, roller or spray for water proofing coating as Per ....Mier specificatIons with following steps (a)surface preparation -Providing and cleaning o1 concrete ...lece le remove dust, oil, grease including removal of existing loose paint r coating, and cement laitance by cleaning with comer..ed air 8 water let including all materials, labour, tools complete Ponding test to be done after plugging all outlets and to be checkedtrodentify seepage eakage On identification of seeps cem t be done with non shrink expanding admixt e a Ind, t 1MYK c g / Dr Fout/Fosroc or equive teems such as those betwe be chamfered with 15 1 41 admixed with ac Fixit or equivalent slum, of acrylic concretein base rovtartg and repaving of all c arapet wall and the roof slab et 50 mm fillet of mortar (Cement sand mer of Sika/ Fosroc/MYK SchomberglDr chamfering a prime coat shall be given with the Repairing surface irregularities, damaged ad cracks if any, with an acrylic
Covering of treated surface with PCC .- Providing 25 mm thick Cement Alf, Concrete M20 1:1. :3) maintaining slope in alternate 2 mt x 2 mt panels with aaprove. of stone chips of 20 mm to 6 mm size graded and cleaned sand 2.5 to 3 including screening,shuttering,and mixing cement concret . fixer with admixture of integral water proofing and placing in posi . ing curing,taxes and royality all complete as per building specifi nd direction of Ell. Panels that has been left shoul be casted next dysThere should be 6 mm gap between Panels .Brand Sika _Plastocrate Aus,MYK proof WP10, Fosroc- Conplast X421 lc& Dr Fixit Pidiproof LW+
Providing and filling of 6 mm thick Groove between 25 mm PCC Panels with Polysulphide Sealant (Poring Grade)as Per drawings and technical specifications and direction of E in Charge (with 18% GST Polysulphicle Fosroc-Thoflex 600.Dr Fixit Pidiseal PS(42P) !MraYndK -Seikaal PS or Euivalent
Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.
Providing 250mm wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 125mm apron including cost of earthwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I.
Providing and laying Doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 / ISO 13006 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm .
Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.
Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent
Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge.
Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by the rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification and direction of E/I.
Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)
Suppling, fitting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in doors, windows, skylight, fanlights and celetial windows openings, including wedge over clamps all complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all complete as per building specification and direction of E/l
Supplying, fitting and fixing 35mm thick solid core type decorative single leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resine of standard make with Aluminium fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.
Supplying, fitting and fixing 35mm thick solid core type decorative double leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with Aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l.
Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm).
Supplying, fitting, and fixing M.S. Grill made of 20X6mm M.S. Flate as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction of E/I. (where materials is not supplied by the deptt.)
Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l.
Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.80 mm thick C.C. paver block of M-30 grade with approved color design and pattern
Providing & fixing of White River (Stone) Pables size of 2" to 2.50" dia in natural colour at site of work including loading, unloading, carriage and all taxes paid etc.and as per direction of officer in charge.
Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item - A0 and disposal of excavated earth as obtained to a distance upto 50M including all lifts levelling, ramming the foundation trenches, removing roots of trees, shurbs all complete as per approved design, building specification and direction of E/I.
Providing 1.5mm cement punning including curing, carraige of water with all leads and lifts as per building specification and direction of E/I.
Supplying and fixing C.I. cover without frame for manholes : 500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg
Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item - A0 and disposal of excavated earth as obtained to a distance upto 50M including all lifts levelling, ramming the foundation trenches, removing roots of trees, shurbs all complete as per approved design, building specification and direction of E/I.
Providing 12mm cement mortar (1:3) with clean coarse sand of F.M. 1.5 with floating coat of neat cement in skirting including rounding of junctions with floor, curing, taxes and royalty all complete as per building specification and direction of E/I.
Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 100 mm nominal size dia
Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.
Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge
Supllying and matarials with lobour for construction inspection chamber of designation class 75b brick deep 600x450 internal diamention having 250mm wall thickness in cement morter(1:6)including 12mm cement plaster (1:4)with punning on inside and cement plaster (1:6)with 600x450mm G.I. cover with frame (weight not less than 36k.g)in foundation and refilling all complete as per specification and direction of E/I.
Supplying and fixing C.I. cover without frame for manholes : 500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg
Cost of Driling 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.(a) From 0.00 M to 50.00 M below G.L.
Cost of Driling 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.
(a) From 0.00 M to 50.00 M below G.L.
(b) From 51.0 M to 125.00 M
Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.200 mm nominal size dia
Supplying all materials, labours, equipments for lowering blue UPVC casing pipes as casing for protecting the sides from falling during the process of drilling all complete including carriage of materials to work site.
Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of useable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, including disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.
Supplying 100mm dis submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump. Submersible pump set 100mm dia (with Polypropylene/ Noryl Impeller) up to 20 stages.2 HP
PVC/XLPE insulated PVC sheathed heavy duty, armoured electrical cable with aluminium conductor for working voltage up to and including 1100 volts.(Conforming to IS:1554, part-1) 6sq.mm, 2 core.
63 amp. Four pole, on load change over switch in sheet enclousre with side handle operation.
Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia
Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp
Supply fitting and fixing of standard make starter panal board do…
Medium density polyethylene pipe (MDPE pipe) in standard length with necessary Jointing material like mechanical connector i.e., thread/insert joint / quick release coupler joint / compression fitting joint or flanged joints confirming to ISO: 4427 : 1996,MDPE pipe of material grade PE-80 PN16 (dia in mm),40 mm dia
Polythene water storage tank of mark with cover and suitable locking system in double layer confirming to IS: 12701-1996 with latest revision.
Providing & fixing brass stop cock of approved quality all complete as per specification and direction of E/I.
(A) Brass stop cock
(c) 25 mm dia
(d) 32 mm dia
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes joining of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I. (Approved Brand - ASTRAL/ SUPREME),Concealed work including cutting chases and making good the wall etc..
15mm dia
20mm dia
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.
25 mm dia
32 mm dia
Supplying, fitting and fixing viteous white glazed earthen ware I.W.C. Of parry Hindustan or any other I.S.S approved make with 100mm H.C.I. p trap 15 liters c.I pull and let go flushing cistern of names or other I.S.S. equivalent make , complete with all fittings.CI or CC brackets 32mm alkathene/PVC telescpope flush,pipe about 2 M long with one brass coupling and clams G.I. chain and pull including supplying and fixing a pair of vitreous white glazed earthen ware footrest to be fixed in floor 15mm C.I body brass spindle stope cock of weight not less than 50grams,15mm PVC connection pipe and 450 mm . long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all comlete as per specification and direction of E/l.(a) 580 mm long (b)12.5 lit. low level P.V.C. cistern
Supplying, fitting and fixing 40 mm high viterous white glazed earthen ware I.W.C. with "p" trap of Parry Hindustan or any other I.S.S. make including supplying & fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450 grms. , 15 mm P.V.C. alkathene pipe 45 cm long with brass coupling at both ends and white/ black plastic solid state seal and lead of commander/ cuckoo or other I.S.S. make with hinges or screw etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l.(B) E.W.C. With "S" trap (b)12.5 lit. low level P.V.C. cistern
Supplying, fitting and fixing flat back or angular, lipped front viterous white glazed earthenware urinal of "Hindustan" " Parry" or any other approved I.S.S. make with all fittings with C.I. or R.S. brackets, standard size G.I. flush pipe with fitting clamps, 15 mm C.I. body brass spindle stop cock of approved quality weight not less than 400 grms. , 15 mm P.V.C. alkathene pipe 450 mm long with brass coupling at both ends and doing plumber joints including painting of exposed part with 2 coats of approved paint over a priming coat of red oxide, cutting wall and floor, making good the same etc. all complete as per specification and direction of E/l.(A) Flat back or standing corner ( 450 mm x 350 mm )
Supplying, fitting and fixing viterous white glazed earthen ware wash hand basin of Parry or Hindustan or any other I.S.S. approved make supported on pointed c.l. or R.S. brackets 32m C.I. brass waste 15mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350grms., 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/l.
Providing and fixing lead connection pipe with heavy quality brass coupling 2 Nos. at both ends etc. all complete as per specification and direction of E/l .(ii) 15 mm dia and 45 cm long
Providing and fixing N.P/C.P brass/P.V.C porcelain shower rose of 15mm inlet etc. all complete as per specification and direction of E/l.(c) 150 mm dia P V C shower
Providing and fixing male ended 15 mm dia brass bib cock of approved quality ( wt not less than 350 gms ) with extra socket all complete as per specification and direction of E/l .
Providing and fixing 15mm size C.P brass pillar cock (Weight not less than 350 gms) C.I body brass spindle pillar cock of approved quality as per spcification and direction of E/l.(b) C.I. body brass spindle
Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/l.a, Glass shelf with C.P brass rail ,i) 600 x 125 mm glass shelf complete
Mirrors of 4 mm thick plate glass bevelled edge mirror including C.P brass revolving fittings, 3 mm plywood board and C P hinges to fix with mirror,i) 600x450 mm
i) C.P brass towel rail 20 mm x 600 mm with bracket container
ii) C.P brass shop dish container medium quality with screw and hinges etc.
(iii) C.P brass liquid shop container
Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:Inside dimensions 600x 850 mm and 45 cm deep for pipe line with three or more inlets :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm dia
Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.75 mm dia
Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.150 mm dia
Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.
75 mm Coupler
110 mm Coupler
75 mm Single pushfit Coupler
110 mm Single pushfit Coupler
75 mm Single tee with door
110 mm Single tee with door
75 mm Single tee without door
110 mm Single tee without door
75 mm Bend 87.5°
110 mm Bend 87.5°
75 mm Shoe (Plain)
110 mm Shoe (Plain)
Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1KV grade of size exceeding 95 sqmm but not exceeding 185 sq mm direct in ground including excavation, sand cushioning, protective covering and refiling the trench etc as required.
PVC / XLPE insulated PVC sheathed heavy duty, armoured electrical cable with aluminium conductor for working voltage up to 1100 volts. (Conforms to IS : 1554, part-1),16 sq mm, 4 core
Supplying and making cable route marker with cement concrete 1:2:4 (1cement: 2coarse sand : 4graded stone agreegate 20mm nominal size) of size 60 cm X 60 cm at the bottom and 50 cm X 50 cm at the top with a thickness of 10 cm including inscription duly engraved as required.
Providing & fixing M.V. danger notice plate of 250 mm X 150 mm, made of mild steel, at least 2mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.
P/F G.I. lighting conductor finial :- providing and fixing of lighting conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.
P/F G.I. lighting conductor tape in horizontal run:- providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lighting conductor complete as required.
P/F G.I. lighting conductor tape in vertical run:- providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lighting conductor complete as required.
Reverting, sweating and soldering of copper / G.I. tape with another copper / G.I. tape, base of finial or any other metallic object as required.
Providing fixing testing joint made of 20 mm X 3 mm thick G.I. strip 125 mm long with 4 nos G.I. bolts. Nuts chuck nuts and spring washers etc. complete as required.
Earthing with copper plate 600mmx 600mmx 3mm thick including acessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.(but without charcoal or cock and salt) complete etc. as required.
S/L 8 SWG G.I. wire in ground :- Supplying and laying 8 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including soldering etc. as required.
Providing & laying earth connection from earth electrode with 4mm dia copper wire in 15mm dia G.I. pipe from earth electrode, as required.
S/F rewireable double pole/TP&N switch disconnector:- Providing and fixing following DP/TP&N sheet metal switch disconnector fuse unit in the existing metal board with rewireable type fuses, including drilling holes in metal board. Making connection etc. as required.
16 amps, double pole
32 amps, double pole
Providing and fixing following rating and breaking capacity MCCB with thermomagnetic release and terminal spreaders in existing cubical panel board including drilling holes in cubical panel, making connections etc. as required.25 - 100 amps, 10 KVA fixed thermal setting
Providing and fixing following capacity bus bar chamber with 4 strips of length 300 mm made of copper suitable for following capacity complete with all accessories including connections, earthing the body etc. as required.100 amps
Providing and fixing following capacity 2pole / 4 pole ON / OFF - load changeover switches with side handle operation, in sheet enclosoure in existing metal board including drilling holes in metal board, making connection, earthing the body etc. as required.
32 amps, 2 pole
63 amps, 2 pole
Providing and fixing following ways surface / recess mounting, vertical type 415 volts, TPN MCB DB of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incommer) as required.
4 way ( 8 + 12 ), double door vertical type
8 way ( 8 + 24 ), double door vertical type
Supplying and fixing 6 amps to 32 amps rating, 240 volts, 10 KA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB's DB complete with connections, testing and commissioning etc. as required.6/32 amps, single pole
Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.
Supplying and fixing following rating, four pole ( three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having sensitivity current 30 mili amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.16/25 amps
Wiring for light point / fan point / exhaust fan point / call bell point with 1.5 sqmm FR PVC insulated copper conductor single core in surface / recessed PVC conduit, with modular switch, modular plate suitable GI box etc as required.Group C
Wiring for twin control points with 1.5 sq mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, 2 way with modular switch, modular plate, suitable GI box etc. as required.
Wiring for light/power plug with 2 X 4 sq mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, along with 1 nos 4 sq mm FR PVC insulated copper conductor single for loop earthing etc as required.
Wiring for Circuit / sub main wiring along with earth wire with following sizes of FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit as required.
2 X 1.5 sq mm + 1 X 1.5 sq mm earth wire
2 X 2.5 sq mm + 1 X 2.5 sq mm earth wire
Supplying and fixing stepped type electronic fan regulator on the existing modulat plate & switch box including connections but excluding modular plate etc. as required.
Supplying and fixing modular blanking plate & switch box excluding modular plate etc. as required.
Supplying and fixing following size / modules, GI boxes along with modular base & cover plate for modular switches in recess etc as required.
1 or 2 Module
6 Module
9 Module
12 Module
Supplying and fixing suitable GI box with modular plate and cover in front on surface of in recess, including providing & fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch connection, painting etc. as required (For light plugs to be used in non residential buildings)
Supplying and fixing suitable GI box with modular plate and cover in front on surface of in recess, including providing & fixing 6 pin 15/16 amps modular socket outlet and 15/16 amps modular switch connection, painting etc. as required (For light plugs to be used in non residential buildings)
Supplying and fixing of following modular switch / soket on the existing modular plate & switch box including connection but excluding plate etc. as required
5/6 Amps , one way switch
15/16 Amps , one way Switch
5/6 Amps socket one way
15/16 Amps socket one way
Supplying and fixing 2 pin 5 amp. Ceiling rose on the existing junction box / wooen block including connection etc. as required.
Supplying and fixing Batten / angle holder including connection etc. as required.
Supplying and fixing ding dong sound call bell single phase 230 voltscomplete as required.
Supplying, Installation, testing & commisioning of following size ceiling fan 3 blades confirming to IS:374:2019 including the wiring down rods of standard length up to 30 cm with 1.5 sq mm FR PVC insulated copper wire suitable for 230V 50HZ, single phase supply etc. complete as required.1400 mm (56") BLDC 5 star rating 32 W Ceiling fan.
Installation of exhaust fan up to 450 mm sweep in the existing opening including making the hole to suit the size of the above fan making good the damage, connection, testing , commissioning etc. as required.
15" (380 mm ) metal exhaust fan
S.I.T.C. of flowing rating reccess / surface mounted LED round / Square shade down light luminaire with pressure die cast housing for single phase supply voltage. Luminaire shall be confirming to IS: 10322 part-5 / section-2 or IEC:62722 with all neccssary accessories as required.12 W LED Round Down light
9/10 Watt LED Bulb
Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).
Supplying and stacking of good earth at site including royalty and carriage upto 5 km complete (earth measured in stacks will be reduced by 20% for payment).
Supplying and stacking sludge at site including royalty and carriage upto 5 km complete (sludge measured in stacks will be reduced by 8% for payment).
Providing and displaying of Philodendron Burgundy plant mounted on moss stick 90 cm ht., well developed with full of fresh & healthy leaves from bottom to top in 25 cm size of Earthen pot / Plastic pot & as per direction of the officer-in-charge.
Providing and displaying of Philodendron emrald red colour plant, mounted on moss stick 90 cm ht., having 3 plants placed at equal distance, well developed with full of fresh & healthy leaves in 25 cm size of Earthen pot / Plastic pot & as per direction of the officer-in-charge.
Providing and displaying of Aglaonema Silver Queen having 30 cm to 45 cm. ht. with 12 to 15 leaves, multi suckers, fresh and healthy leaves, well developed in 25 cm dia Earthen pot/Plastic pot & as per direction of the officer-in-charge.
Providing and displaying of Aglaonema ernesto (three in one), having ht. 45 cm & above with 12 to 15 leaves, well developed, fresh and healthy in 25 cm size of Earthen pot/Plastic pot.& as per direction of the officer-in-charge.
Providing and displaying of Aglaonema marentifolium variety having ht. 23 cm to 30 cm with 8 to 10 leaves, well developed, fresh and healthy with colorful leaves in 20 cm size of Earthen pot/Plastic pot. & as per direction of the officer-in-charge.
Providing and Displaying of Alpinia Variegated (three in one) plant having ht. 30 cm and above , with fresh and healthy variegated foliage in 25 cm size of Earthen Pot / Plastic Pot & as per direction of the officer-in charge.
Providing and stacking of Alternanthera species of height 15 cm to 20 cm, full of branches and foliage in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.
Providing and stacking of Asparagus marrie, well developed 15 to 20 leaves, full of branches and foliage in 25 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.
Providing and stacking of Euphorbia milli hybrid variety, having ht. 30 cm to 45 cm with multi branch, full bloom, fresh and healthy leaves in 30 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge..
Supply and stacking of Delonix regia (Gulmohar) plant of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge
Providing and displaying of Phoenix palm having ht. 75 cm to 90 cm with 10 to 15 or more leaves, well developed, fresh and healthy in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.
Supply and stacking of Nauclea cadamba (Kadam) plant of height 150-165cm. in big poly bag of size 25 cm as per direction of the officer-in-charge.v
Providing and stacking of Polyalthia longifolia (Ashok) of height 180-195 cm. in gunny bag of size 30 cm as per direction of the officer-in-charge.
Providing and stacking of Bottle palm of ht. 150-180 cm bottom girth 20-25 cm well developed in big poly bags of size 25 cm as per direction of the officer-in-charge.
Providing and stacking of Michelia champa (Golden Champa) of height 90- 105 cm. in earthen pots of size 25 cm as per direction of the officer-in-charge.
Supply and stacking of plant Bauhinia tomentosa (yellow) of height 60-75 cm. in earthen pots of size 20 cm as per direction of the officer-in-charge
Providing and stacking of Iresine herbstii, of height 20-25 cm. full of branches well developed in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.
Providing and stacking of Juniperus prostrata with 5 to 6 latral branches and green foliage in 20 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.
Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water)
Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, hedge, flower beds, foliages, creepers etc. including hoeing,weeding pruning replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter , removal of garden waste, applying insecticide, pesticide & fertilizers(whenever required) top dressing of lawn with good earth and menure and maintenance of other garden related works as directed by office-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide , Pesticide will be provided by the Department & lawn mover and brush cutter with fuel , other T & P material/articles shall be provided by the contractor.) Open spaces(as per yard stick 1Mali =3.00Acre).
Carriage of Material
Bricks =8 km(1+7)
Sand=8 km
Sand - 12 km
Stone chips & boulder =22 km
Add 18 % GST
Add 1% Labour Cess
M/S UNIVERSAL TELECOM (BID ID -674357)
N K Enterprises (BID ID -673882)
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid