PROVN OF SEPTIC TANK, DG SET, TOILET BLOCK AND SPL REP TO CERTAIN BLDG UNDER AOR OF GE 874 EWS

Amount

Demolition of brick or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Dismantling posts or struts (wood, steel or R.C.C.) embedded in concrete brick work, masonry, etc. any section including taking out embedded portion and making good disturbed ground complete all as specified and directed.

Taking down cement or cement lime plaster of any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete as specified and directed.

Dismantling floor, hearth or wall tile/ stone slabs including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises etc complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with nails, complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/ slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

Dismantling in fillets, rails, posts, rafters, purlines, etc in any position complete all as specified and directed.

Dismantling timber scantling, in any description, fixed in any position complete all as specified and directed.

M & L for dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings etc complete all as specified and directed.

Taking down chowkat with shutters n. exc.1.5 Sqm (w/o taking off shutters from chowkhat) including all fitting complete all as specified and directed.

Taking down chowkat with shutters exc.1.5 Sqm but n exc.4 Sqm (w/o taking off shutters from chowkhat) including all fitting complete all as specified and directed.

Taking up or down 15 mm steel tubing and connections including for refixing removal to store complete all as specified and directed.

Taking up or down 20 mm steel tubing and connections including for refixing removal to store complete all as specified and directed.

Demolition and braking up drain pipe (SGW, AC, RCC) set in cement mortar complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, laying of cable, pipe, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft/loose soil.

M&L for Brick work sub class 'B' bricks, straight or curved on plan exceeding 6 metre mean radius, built in cement, mortar 1:4, complete all as specified and directed.

M&L for Walling of random rubble stone uncoursed, well bonded, bedded and solidly hearted, built in CM (1:4), complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick complete all as specified and directed.

M&L for providing cement concrete type B-0, 1:2:4 using 12.5mm graded stone aggregate 25 mm thick as in flooring finishes the surfaces even and fair without using extra cement complete all as specified and directed.

M&L for Plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

M & L for Cement concrete 1: 3: 6 type C-2 using 40 mm graded stone aggregate as in surface channels and drains and extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. complete all as specified and directed.

M&L for plain cement concrete (1:2:4) type B-1 using (20mm graded crushed stone aggregate) as in copings, plinth band, bed blocks and like slightly rounded or chamfered angles as directed including necessary form work complete all as specified and directed.

M&L for rendering 10mm thick on fair faces of brick work or concrete surface, in cement mortar 1:6 finished the surface even and smooth without using extra cement complete all as specified and directed.

M&L for 15 mm thick rendering cement plaster in cement mortar (1:4) on stone masonry surface or other than fair faces of brick work, finished even and smooth without using extra cements complete all as specified and directed.

M&L for raised pointing in CM 1:4 to random or polygonal rubble, uncoursed or brought up to courses complete all as specified and directed.

M&L for PVC (SWR) pipes, single socketed, in any length, with rubber rings 75 mm dia complete all as specified and directed.

M&L for PVC (SWR) pipes, single socketed, in any length, with rubber rings 110mm dia complete all as specified and directed.

M&L for Non-skid ceramic-coloured tiles 7-8 mm thick, area exc 0.06sqm but n exc 0.11 sqm of each tile in floor etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile over and including 15 mm thick screed bed in CM 1:4 including providing 25mm thick PCC 1:2:4 type B-0, using 12.50mm graded crushed stone aggregate complete all as specified & directed.

M&L for Vitrified Ceramic light shade tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete laid over and including 15mm thick screed bed in CM 1:4, complete all as specified and directed.

M&L for machine cut Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over and including 15 mm thick rendering in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified & directed.

M&L for Glazed ceramic coloured tiles of size 300 x 200mm and 7mm thick, as in vertical surface such as in skirting and dado etc, set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, over and including 10mm thick rendering in CM 1:4 complete all as specified & directed.

S & F granite (of any type) work (table rubbed and polished) in steps Jambs, pillars, window cills, platform and likes 16-18 mm thick in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture pigment to match with shade of granite, complete all as specified and directed.

S & F stainless steel drapery or curtain rods, 25 mm dia, with end brackets, decorative type cut to length as required size, colour coating including matching socketed brackets complete all as specified and directed.

S & F for 2nd class soft wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S & F for plain framed, panelled shutters 30mm thick 2nd class softwood, (any numbers of panels), with panels of timber flats on both sides of veneered particle board med density, wood particle board with commercial face fitted to chowkhat complete all as specified and directed.

All as per item No 38 above but for window and ventilator shutter with stiles and rails all as specified in SSR Part-I, section 8 clause 8.24(b) complete all as specified and directed.

S & F for MS barrel tower bolt, stove enamelled black, with bright bolt of 150mm long complete all as specified and directed.

All as per item No. 40 above but 100 mm long.

S & F for mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed of 300mm long complete all as specified and directed.

S & F for mild Steel butt hinges medium weight, cold rolled 100mm long complete all as specified and directed.

All as per item No. 43 above but 75 mm long.

M & L for mild steel pressed handles, oval type, stove enamelled black of 100mm long.

All as per item No. 45 above but 75 mm long.

Hacking out old broken glass (any thickness, size quality of description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

S&F for 4 mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

S & F in repair Galvanized mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned stacks, or galvanized wire staples complete all as specified and directed

S & F Galvanized mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned stacks, or galvanized wire staples complete all as specified and directed

M&L for framed and fixed timber scantling second class soft wood for post, sturts etc (except Timber) complete all as specified and directed.

S & F for 20mm thick, second-class soft wood boarding, planed one side, with butt joints and fixed with nails in facia, eaves boarding, complete, (except flooring and skirting) complete all as specified and directed.

All as per item No 52 above, but except boarding, complete all as specified and directed.

M&L 2nd class soft wood wall /ceiling panelling of good quality wood planed one side and edge tonged and grooved or rebated other side and dovetailed joints, chamfered both side fixed to frame work with secret nailed as in wall panelling 15 mm including cornice and beading as required and applying two coats of varnish over a filler coat of thin varnish after preparation of the surface, complete all as specified and directed. Note: Frame work shall be measured and paid separately.

M&L ply wood 4mm thick 3 No ply grade BWR, type fixed with screws to timber frame as in ceiling applying two coats of varnish over a filer coat of thin varnish after preparation of the surface, complete all as specified and directed. Note:-Frame work shall be measured and paid separately.

All as per item No 55 above but except ply wood

S&F for plain fillets, rectangular or triangular in section clean sawn, secured with nails or brads sectional area exc 3 Sqcm & nexc 6 Sqcm, second class soft wood (Kail) complete all as specified.

M&L Second Class soft wood clean swan in timber scantling complete all as specified and directed.

S&F for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self-tapping screws, complete all as specified and directed.

S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self-tapping screws complete all as specified and directed.

S&F PVC connections 15 mm size with PTMT nuts of length 600mm complete all as specified and directed.

S&F PVC (SWR) floor trap 75mm dia outlet, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F PVC gully trap square or round mouthed type (P), size of trap 125x 110mm and jointing to drains with solvent cement in repairs complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F Vitreous China European type water closet of size 700 mm x370mm x 410 mm and making necessary connection to drain or outgoing pipe fixed on floor fixed in repairs completed all as specified and directed

M&L for Vitreous china squatting Pan "Orrisa Pattern" size 580 x 440mm white with integral foot rests including flush pipe of PVC 32mm dia for low level cistern fixed in repair complete all as specified and directed.

S&F in repair PVC valveless syphonic action type flushing cistern, low level white with inlet ball valve float and handle including brackets (10 Ltr) capacity, with flush pipe etc fixed complete all as specified and directed.

M & L for Vitreous china wash basin, vertically mounted fancy bowl flat back size 550 x 400 m including waste pipe and coupling 32mm for basins, etc. with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed including MS brackets& waste Pipe complete all as specified and directed.

S&F Pillar tap 15mm bore cast copper alloy, with capstan head chromium plated screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

M&L for Stop/Angle valve 15mm bore, cast copper alloy screwed down, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F bib tap cast copper alloy chromium plated fancy type with crutch of butterfly handle, screwed down, screwed for iron pipe of for brass ferrule of 15mm bore (ISI marked) complete all as specified and directed.

S & F tubular towel rail 60 cm long, aluminium anodised fixed with and including CP brass screws and wooden/plastic cleats complete all as specified and directed.

S & F Waste coupling of PTMT (half or full thread) (Minimum weight 32 mm-45 gms / 40mm-60gms) for 32mm bore dia of discharge pipe to WHB etc complete all as specified and directed.

S &F in repair 15 mm bore, steel water tubing medium grade, galvanized with all fittings and fixed complete to walls and ceiling or laid in floor complete all as specified and directed.

S&F in repair 20 mm water tubes, ‘medium grade’ galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

M&L for applying two coats of 100 % premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004 ,Alkali & fungal resistance ,dirt resistance exterior paint of required shed all as specified and directed.

M&L for preparing new plastered surfaces of wall and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and directed.

M&L for preparing new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of 3 mm thick wall care putty including primer complete all as specified and directed.

M&L for complete removal of old decorative plastered surfaces of wall including cornices, pilastered etc by brooming down or steel wire brushing ,scraping down smoke soot ,moulds ,moss and efflorescent salt and trading oil and greasy spots including filling depressions of scrapped surfaces and applying two coats of oil bond distemper over and including a coat of 1 mm thick wall care putty with preparation of plastered surfaces complete all as specified and directed.

M & L for complete removal of old decorative plastered surfaces of wall including cornices, pilastered etc by brooming down or steel wire brushing ,scraping down smoke soot ,moulds ,moss and efflorescent salt and trading oil and greasy spots including filling depressions of scrapped surfaces and applying two coats of 100 % premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance ,dirt resistance exterior paint of required shed complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint over a coat of pink primer including preparation of new untreated wooden surfaces of any description, not otherwise described over 10cm width or girth complete all as specified and directed.

M&L for applying one coat of synthetic enamel paint including preparation of old treated steel surfaces of any description, not otherwise described over 10cm width or girth complete all as specified and directed.

M&L for cement concrete bed in PCC (1:4:8) type D-2 to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested and make sewer line functional for 150 mm dia bore pipe complete all as specified and directed.

Surface excavation n. exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out Soft/loose soil complete all as specified and directed.

M&L brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed.

M &L for second class soft wood as in scantling clean sawn fixed in position.

M&L for applying two coats of oil bound distemper on internal wall surfaces over a coat of primer including preparation newly plastered surface complete all as specified and directed.

M&L for moorum/red bajri filling in floors or paving, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L for hard core filling under floor, breaking stone or boulder exc 63mm and n. exc 100mm gauge of sand stone complete all as specified and directed.

M&L for 75mm thick PCC type D-2 1:3:6 (40 mm graded crushed stone aggregate) as in sub base of floor complete all as specified and directed.

M&L for Non skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm and n.exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM (1:4) laid over and including 25mm thick PCC (1:2;4) type B1 using 20 mm graded crushed stone aggregate, complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plaint color PVC sheet reinforced with MS square tube, and fitted in opening complete all as specified and directed.

S&F factory made solid PVC moulded door shutter with particle board core 28 to 30mm thick (style) with 2, 4, or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face, supplying and fixing in frame at site as per specification and drawing.

S&F steel ventilator with top hung shutter including hinges, steel peg stay, complete with glazing bars, dove tailed or welded including one shop coat of zinc chromite primer complete all as specified and directed.

S&F Sheet glass ordinary quality 3mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50Sqm in each pane, in repairs, complete all as specified and as directed.

S&F Aluminium handles, cast type, anodised 150mm size complete all as specified and directed.

S&F 150mm size Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

M&L for PCC 75 mm thick 1:3:6, type C-1 (using 20mm stone aggregate as in plinth protection complete all as specified and directed.

S&F rotational moulded polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed in position of 500 ltrs capacity fixed with PVC tank nipples, complete all as specified in SSR Part-I.

S&F Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe and fixed with 15mm dia complete all as specified and directed.

S&F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and directed.

S&F soap dish, vitreous China white, approximate size 160x 160x90mm complete all as specified and directed.

S&F PVC connection 15mm dia and 600mm long with PTMT nuts and washer complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipe single socket in any length with rubber ring jointed, fixed to wall complete all as specified and directed.

S&F 110mm bore PVC (SWR) bend or tee or radius complete all as specified and directed.

M&L for PVC (SWR) WC connector with lip ring 110mm complete all as specified and directed.

M&L for PVC (SWR) vent cowl for 75 mm dia complete all as specified and directed.

S&F grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified and directed.

M&L for concrete bed 1:3:6 type C-2 using 20 mm graded stone aggregate to drain pipes 100 mm dia bore including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

Excavation over areas, n exc 1.5 m deep and getting out soft/loo soil complete all as specified and directed.

M & L for PCC 1:3:6 Cement concrete type C-2 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed.

M & L for rendering 15 mm thick in CM (1:4) on fair faces of brick work or concrete surfaces rendering is to be finished even and smooth (without using extra cement) complete all as specified and directed.

M&L for precast cement concrete 1:2:4 type B-1, using (20 mm graded crushed stone aggregate) but in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces complete all as specified and directed.

M&L for RCC (1:1.5:3), using 20 mm graded crushed stone aggregate, slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M & L for rough finished flat formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed.

M & L for MS TMT bars Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

M&L for 150 mm dia salt -glazed stoneware drain pipes laid in trenches and jointed complete all as specified and directed.

M&L for cutting into existing manholes for using 150 mm dia bore of pipe connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching complete all as specified and directed.

M&L for construction of Soakage well, of size 3.60 m dia at bottom and 6.00 m total depth complete all as specified and shown on drawing No. CESZ-TD-/2015 sheet No 1/3 & 3/3 dated 22 Feb 2015 (Revised dt 21 Mar 2015) and specified in particular specifications.

M&L for conventional 10 users on site LLDPE septic tank designed to carry sewage and sullage water, excavation in any type of soil including providing PCC (1:4:8) type D-2, 150 mm thick in foundation, Vent shaft, connection etc., complete all as specified and directed.

M&L for construction of Soakage well, of size 1.80 m dia at bottom and 3.00 m total depth complete all as specified and shown on drawing No. CESZ-TD-/2015 sheet No 1/3 & 3/3 dated 22 Feb 2015 (Revised dt 21 Mar 2015) and specified in particular specifications.

Taking down carefully copper/ aluminium unserviceable/ perished point wiring (light, fan, socket or power complete including fixture and fittings such as switches, ceiling roses, pandents, regulators, sockets, light fittings, removing material from site for taking credit etc and making good disturbed surfaces of wall, floors, complete all as specified and directed.

Taking down MCB DB's complete with MCB's/Isolator etc removing materials from site and making good disturbed surface of walls, floors etc. complete all as specified and directed.

M&L for point wiring for one light point/fan point controlled by one switch with 1.5 sqmm PVC (FR-LS-H) insulated un-sheathed copper conductor single core multi strand flexible cable and 1.5 sqmm PVC (FR-LS-H) insulated un-sheathed copper conductor single core multi stranded flexible cable (green colour) as earth lead in and including cable 1100 volts grade including casing and capping (ISI marked) for one light/ fan point controlled by one switch including CI/MS sunk box of required size, & as directed by Engr in Charge including 3mm thick plastic laminated top sheet cover, including cutting chases to wall and making good the disturbed surfaces to match with the existing specification complete all as specified and directed.

All as per item No 126 herein before but wiring with 1.5 sqmm copper wire (FR-LS-H) and 1.5 sqmm earth wire for socket outlet 3 pin 5 amps on same board.

All as per item No 126 herein before but wiring with 1.5 sqmm copper wire (FR-LS-H) and 1.5 sqmm earth wire for socket outlet 3 pin 5 amps on independent board.

All as per item No 126 herein before but wiring with 2.5 sqmm copper wire (FR-LS-H) and 1.5 sqmm earth wire for socket outlet 6 pin 15 amps on independent board.

S&F switch piano flush button single pole, one way 5 amps complete all as specified and directed.

S& F of Socket outlet 2 in 1, 3 pin, 6A complete all as specified and directed.

S & F switch socket combination 2 in 1,5A, flush type complete all as specified and directed.

S & F switch socket combination 5 pin 16A, flush type complete all as specified and directed.

Supply and fix ceiling rose with earth terminal connection, 3 terminal/ PVC/ polycarbonate, isolated body complete all as specified and directed.

S&F LED, 20 Watts, 4 ft, fittings complete with all accessories for mounting light fittings complete with earth terminal connection, 3 terminal/ PVC/ polycarbonate, isolated body. complete all as specified and directed.

M & L for Lamp holder, PVC/Polycarbonate type with cord grip cap suitable for pendant fittings complete all as specified and directed.

Supply and fix LED Bulb 9 Watt complete all as specified and directed.

S&F 09W/10W Bulk head luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F Exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230V, 50HZ, RPM 1200, Copper winding of sweep 300mm, with complete all as specified and directed.

M&L for Wiring for circuit/submain wiring along with earth wire with the following sizes of FR-LS-H PVC insulated copper conductor, single core cable in surface/recessed as required in PVC casing caping of size 2x4sq. mm + 1x2.5 sq. mm earth wire

S&F of distribution board single pole & neutral with 200 Amps rated bus bar, for double door IP-42 DB’s made out of sheet steel enclosure, recessed type, factory made powder coated 8 way -240 volts suitable for housing MCB's and isolator's complete in all fixing material/accessories etc complete all as specified and directed.

S&F of distribution board single pole & neutral with 200 Amps rated bus bar, for double door IP-42 DB's made out of sheet steel enclosure, recessed type, factory made powder coated 4 way -240 volts suitable for housing MCB's and isolator's complete in all fixing material/accessories etc complete all as specified and directed.

S&F MCB's single pole 240 volts 6 to 32Amps 10 KA 'C’ curve series complete all as specified and directed.

S & F of MCB SPN, 240 volt, 32 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

Supply and Fixing 1100 Volts grade heavy duty cable PVC insulated multistranded aluminium conductor served with PVC tape and overall PVC sheathed in services connections suspended by insulating hanger not more than 1 mtr apart including 4mm dia GI suspension wire one twin core cable flat or circular of size16 Sqmm 2 core including service bracket complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60x60cmx6.3 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge lead of the plate not less than 1.5 mtr below normal ground level, connected galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in Electrical plate No 3 connected to earthing test point all as specified or indicated including testing on completion.

Supply & laying Sand coarse dry as in cushioning of underground electric cable in trenches, laid to a uniform thickness of 23cm (15cm under the cable & 8cm over the cable) and gently punned down to 18cm thickness all complete all as specified and directed. Note: - Only punned down sand thickness 18CM shall be measured and paid.

M&L for Supplying and laying un-reinforced precast concrete cable cover, class LV, type 1, flat, size 250mm x 150mm x 40mm complete all as specified and directed.

M&L for Supply and laying/fixing GI tubing light grade ISI marked for cable protection of size 50 mm dia complete all as specified and directed.

M&L for Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 2 core complete all as specified and directed.

S&F GI water tubing 20mm dia bore 'medium grade', galvanized, with all fittings like socket, union, elbow, bend, tees etc jointed and laid in trenches/Wall complete all as specified and as directed.

All as per description of srl item No-151 above but 25mm dia bore.

All as per description of ser item No-151 above but 40mm dia bore.

S&F gun metal, globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of bore of 20mm complete all as specified and directed.

All as per description of ser item No-154 above but 40 mm dia bore.

M&L for lagging to pipes used in water supply or plumbing all round with, 40 mm thick bounded mineral wool preformed 'SNAPON' pipe section of density 144 Kg/cum conforming is IS 9842. On pipe of internal dia 20 mm with chicken mesh wire netting 25 mm gauge,20mm mesh complete all as specified and directed.

M&L for construction of masonry valve pits of size 60x60x60 complete with MS Sheet cover and locking arrangement etc suitable for pipes up to 50 mm complete all as specified and directed.

M&L for cutting of existing DI/CI/GI steel tubing (of any size) for alteration or additions and insertion of Tee of required size for output connection of 50 mm GI pipe, union, socket complete all as specified and directed.

Supply and installation of 7.5 KVA 1 Phase Kirloskar Green Silent DG Set comprising of KIRLOSKAR make Diesel Engine model 2R550NA 4G1 (CPCB IV+ NORMS COMPLIANCE developing 10.74 BHP @ 1500 RPM 7.5 KVA, Alternator rated at 1 phase, 230 Volts , 50 Hz: 0.8 p.f @ 1500 RPM both mounted, and aligned on a common MS base frame complete with MS Fuel Tank, Manual Control Panel Residential Exhaust Silencer, AVM pads fitted on base frame ,1 No. 12 Volts DC Battery, Battery Leads, 1st Fill of Lube Oil all housed in Sound proof Acoustic Enclosure complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 2 core complete all as specified and directed.

Supplying and laying old size bricks, laid flat ie length of brick shall be laid across the cable, common burnt clay building bricks sub class `B' designation 75 complete all as specified and directed and testing on completion complete all as specified and as directed by Engineer in charge.

M&L for point wiring for one light point/Ex/fan point controlled by one switch with 1.5 sqmm PVC FRLS insulated un-sheathed copper conductor single core multi strand cable and 1.5 sqmm PVC FRLS insulated un-sheathed copper conductor single core multi stranded cable (green color) as earth lead in and including cable 1100 volts grade including 25mm casing and capping (ISI marked) for one light/ fan point controlled by one switch including CI/MS sunk box of required size, & as directed by Engr in Charge including 3mm thick plastic laminated top sheet cover, including cutting chases to wall and making good the disturbed surfaces to match with the existing specification complete all as specified and directed.

M&L for LED Batten 1x20 W for regal batten for LED universal batten for G 13 T with 18 W tube rods and Ultra bright LED Polycarbonate tube light very high efficiency suited for installation in existing T8 and connecting electrically using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core all as required at site complete all as specified and directed.

Supply and fixing lamp holder bracket type, PVC/polycarbonate type with skirt cap suitable for batten fittings, complete all as specified and directed.

RATHER BROTHERS (BID ID -3105960)

patriotic builders (BID ID -3097159)

M/S MUNEER AHMAD WANI CONSTRUCTIONS (BID ID -3096981)

Bidder Name

M/S AB AHAD RATHER

patriotic builders

RATHER BROTHERS

M/S MUNEER AHMAD WANI CONSTRUCTIONS