CA NO CWE/CHM-03/2020-21 PROVN OF FURNITURE FOR OTM ACCN FOR FD REGT (PHASE-II) AT CHANDIMANDIR AND RENEWAL OF FURNITURE AGAINST SURVEYED OFF FURNITURE AT BSO GE CHANDIMANDIR

Amount

PART I WOODEN FURNITURE

TABLE PEG (DRG NO FD-277/384) Ist class seasoned teak wood shall be used through out. Top shall be made out of pre-laminated particle board 18/19 mm thick ISI marked exterior gde. 6 mm thick teak wood beading shall be used all around at top. Rubber PVC shoes shall be provided at the bottom of legs duly screwed. All wood surfaces shall be French polished to a glossy finish . Rest all as per drg complete all as shown as Drg No FD-277 complete all as specified and directed.

CHAIR DINING (DRG NO FD-1105/279) Teak wood Ist class shall be used through out . Canning shall be done/woven in Godrej pattern with cane plastic 2 mm wide and 3 mm wide for border. Make of cane shall be of Premier/ Usha. All exposed surfaces shall be french polished to a glossy finish. Rest all as per drg No FD-1105 complete all as specified and directed.

SIDE BOARD (DRG NO FD-241) All side shall be made out of Prelaminated Perticale board 18/19 mm thick. Top shall be made of Prelaminated Perticale board 18/19 mm thick . All wood surfaces exposed to view shall be French polished with high gloss finish. Complete prelaminated perticale board 18/19mm thick.

TABLE WRITING (DRG NO FD-275) (a) All wood work shall be of 1st class hard wood (Teak). (b) Irrespective of what is shown in the drawing, top of table shall be of 18MM thick Pre-laminated particle board exterier grade. 4MM thick teak wood edging shall be provided all-round. (c) Front of drawer and shutter of cabinet (below drawer) shall be of 18MM thick Prelaminated particles board (Prelaminated perticale board exterier grade sides, bottom and shelf of cabinet shall be of 18 MM prelaminate perticale board as per drg. (d) Bottom of drawer and back cabinet shall be of 6MM thick commercial plywood as per IS - 303. (e) All exposed surfaces of timber & wood based surfaces ( except laminated surfaces) and prelaminated particle board and 4mm teak wood bedding shall be French polished. (f) All joints fixing shall be done in accordance with standard workmanship and specifications. (g) Rest all as shown on drawing and as directed by GE/Engr-in-charge.

SOFA SET 4 SEATER WITH CUSHION (DRG NO FD-373) The set shall consist four small pieces of one seat . Timber work shall be of Ist class seasoned teak wood. Foam shall be 100 mm thick cushion of ‘cool’ foam of 40 density of size 530mmx500mm covered with best quality tapestry cloth of rate not less than Rs. 450/metre of approved make. All wood surfaces exposed to view shall be French polished. Rest all as per drg No FD-373 complete all as specified and directed.

CHAIR EASY (DRG NO FD-229) Teak wood seasoned 1st class shall be used through out. Canning shall be done with cane plastic 2mm thick and 3mm for border. Cane plastic shall be used of premier/Usha. Make - All exposed surfaces shall be french polished to a glossy finish and all as per drg No FD-229 complete all as specified and directed.

TABLE DRESSING GENTS WITH MIRROR (DRG NO FD-230/379) All wood shall be of Ist class hard wood teak .The bottom side of dressing table shall be of 18/19 mm thick prelaminated perticale board & prelaminated particle board 18/19mm on other side. Top shall be of 18/19 mm thick commercial particle board Frame work of mirror shall be of Ist class teak wood back shall be of ply wood 6 mm commercial ISI marked, Mirror shall be 5 mm thick ISI marked. Make of mirror shall be Atul/Modi. All wooden surfaces shall be French polished to a glossy finish and all as per drg No FD-230 complete all as specified and directed.

TABLE DINING 6 PERS (DRG NO FD-272) All as shown on drg. Over all size shall be 1500 mm long, 900 mm wide and 760 mm high. Frame shall be made out of teak wood through out. Top shall be made out of 18 mm pre-laminated particle board ISI marked one side teak face. All wooden portion shall be finished with French polish.

CHAIR DINING WITH CUSHION (DRG NO FD/MAP/E6/10) (a) All wood work shall be of 1st class hard wood (Teak). (b) Seat shall be 75 MM thick foam of 32 density covered with good quality tapestry cloth (cost of cloth not less than Rs 450/- per meter) as approved by GE over 12MM thick commercial plywood as per IS-303. (c) Nylon buffers of appropriate size shall be screwed to the bottom of each leg. (d) All exposed surfaces of timber and plywood shall be french polished. (e) All joint fixing shall be done in accordance with standard workmanship and specification. (f) Rest all as shown on drawing.

TABLE DRESSING LADIES WITH MIRROR (DRG NO FD-251) All wood shall be of Ist class hard wood teak .The bottom side of dressing table shall be of 18/19 mm thick prelaminated pertical board. Top shall be of 18/19 mm thick commercial particle board . Frame work of mirror shall be of Ist class teak wood. Back shall be of ply wood 6 mm commercial ISI marked, Mirror shall be 5 mm thick ISI marked. Make of mirror shall be Atul/Modi. All wooden surfaces shall be French polished to a glossy finish and all as per drg No FD-251 complete all as specified and directed.

BIN MULTIPURPOSE (FD/MAP/E6/03) (a) All wood work shall be of 1st class hard wood (Teak). (b) Teak wood stiffeners of size 25mm x 25mm and legs of size 45mm x 45mm shall be provided as per details shown in the drawing. (c) Back shall be of 12mm thick commercial plywood as per IS-303. (d) Top sides shutter, drawer and shelves shall be of 18mm thick prelaminated perticle board ( one side with decorative lamination of teak finish shade and other side white balancing lamination as specified 4mm thick teak wood edging shall be provided around to all exposed edges of prelaminated particle board shall be 30mm steel chromium plated knobs shall be provided to each shutter as per sample approved by GE/BSO. (e) 16’’ telescopic drawer slides high quality make-lexi centre drawer shall be provided to centre drawer as per sample spproved by GE/BSO and slide drawer O cray auto hinges/ hydraulic aickon hinges) shall be provided to sides drawer as per sample approved by GE/BSO. (f) All shutter shall be provided with mild steel power coated 50mm D type handle. (g) All exposed surfaces of timber, ply wood based surfaces (except laminated surfaces) shall be French polished. (h) Rest all as shown on drawing.

SOFA SET 5 SEATER WITH CUSHION (DRG NO FD-373) The set shall consist of one long piece of three seat and two small pieces of one seat each. . Timber work shall be of Ist class seasoned teak wood. Foam shall be 100 mm thick cushion of ‘cool’ foam of 40 density of size 550 mmx525mmx100mm covered with best quality tapestry cloth rate not les than Rs. 450 per metre. of approved make. All wood surfaces exposed to view shall be French polished and all as per drg No FD-373 complete all as specified and directed.

TABLE 3'x2' WOODEN as per No FD-284 drawing and approved by GE/Engineer-in-Chief.

TABLE BED SIDE as per No FD-276 drawing and approved by GE/Engineer-in-Chief.

STOOL DRESSING CB as per No FD-282/372/27 drawing and approved by GE/Engineer-in-Chief.

Almirah Mess Utensil (DRG NO FD-93) As per drawing and approved by GE/Engineer-in-Chief.

Table Computer (DRG NO FD/E6/MAP/03) As per drawing and approved by GE/Engineer-in-Charge. Make :- Godrej or equivalent.

RECEPTICAL PVC SMALL (DRG NO FD/E6/MAP/13) (a) Recepticle shall be of covered plastic container of 75 ltr capacity made with thick polymer plastic alongwith lid and handles. Recepticle shall be of bright colours ie. Red, Green, Blue etc. (b) Recepticle shall be of make: Blow plast/Neel Kamal/ Supreme/ Cello/Polyset, as approved by GE.

Desk Stand Lecture (DRG NO FD-125) DIMENSION :Over all size shall be 970mm wide and 1220mm high. DESCRIPTION: Two upright of mild steel rectangular tube of 75mmx25mm of 1202mm high shall be provided in rear side and shall be 635mm apart. The two upright shall be joinded with bottom, middle and top rails with 75mmx50mm mild steel tube of wal thickness 1.6mm. The two sides rails at bottom fixed at 125mm from bottom shall be 430mm long 75mmx50mm mild steel tube of wall thickness 1.6mm and shall form the part of bottom rails and join the long side of bottom rail of size 785mm long, . All edges of pre-laminated particle board remained exposed shall be covered with teak wood edging as per the size of board edging. FINISH : All steel surfaces exposed to view when placed in position shall be given two coats of enamel paint over a coat of primer with spray machine after preparation of steel surfaces and all wooden surfaces shall be melamine polish with lacquer finish as approved by Engr-in-Charge.Rest all as per drgs.

Hat Stand with Mirror (DRG NO FD-361) DIMENSION:Overall size shall be 1330 mm long, 710mm high. DESCRIPTION:The inner frame shall be of 50mmx20mm teak wood battens six in nos .The back and front of frame shall be covered with 6mm thick commercial ply.The edges of the frame shall be covered with 6mmx35mm teak wood edging fixed alround the frame with headless nails and adhesive.Six brass pegs 120mm long shall be fixed over the wooden membrane with brass screws as shown in drg.5mm thick looking mirror of (saint gobian,Modiguard/Atul) shall be provided as shown on drg with beading alround . Mild steel key plate shall be provided at both top corners of the hat stand. FINISH: All teak wood surfaces shall be given high gloss French polish with lacquer finish. All steel surfaces shall be painted with two coats of enamel paint over a coat of primer. Rest all as per drgs.

Stool dressing with cushion (DRG NO FD/E6/MAP/14) (a) The plywood 12mm thick wherever shown on drawing shall be 18/19 MM thick decorative type with Prelaminated partical board finish on one side. (b) The seat shall be removable type made of 75MM thick synthetic foam of 40 density covered with tapestry cloth of shade and texture as approved by GE. The tepestry cloth shall be costing not less than Rs 350/- per runing meter. (c) All exposed edges of particle board shall be provided with 4MM thick teak wood edging unless otherwise shown on drawing. (d) All exposed surfaces of wood and wood based material shall be French polished. (e) Rest all as shown on drawing and as directed by GE/ Engr -in-charge.

Teapoy Wooden (DRG NO FD-278) All as shown on drg. Overall size of peg table shall be 600mm long, 450mm wide 540mm high. All wood shall be of Ist class teak wood. Top of table shall be made out of prelaminated particle board 18mm thick exterior grade and 4mm thick teak wood beading shall be provided all round the table irrespective of what is shown on drg and all as per drg No FD-278 complete all as specified and directed.

Chair Eazy Cushioned (DRG NO FD-121(M) DIMENSION:Overall size shall be 510mm long, 545mm wide and 710mm high. DESCRIPTION:Timber shall be seasoned teak wood Ist Quality. Front legs shall be of size 70mmx25mm in section 520 mm high and rear legs shall be of section 70 mm x25 mm in section slanting 185 mm horizontally in the height of 490 mm . The front and rear rails shall be provided below the seat joining front legs and rear legs .Front legs shall be 510 mm apart and rear legs shall be 480 mm apart . The top of front legs shall have wooden arms rest of 65 mm x25 mm in section and 610 mm madfe to shape as shown on drg. The legs shall be joined by side rails 70 mm x 25 mm in section teak wood. The bottom frame of seat shall be of 55 mm x 20 mm in section over which 3/4 mm thick plywood commercial shall be fixed. 75 mm thick foam cushion of 32 density with upholster with leathersied rexine of approved shade and texture as directed by BSO/ GE.Hard rubber/ PVC shoes of 25 mm dia 25 mm high shall be provided to the bottom of legs with screws FINISH: All wooden surfaces shall be polished with two coats of melamine polish with spray machine after preparation of surfaces.

Table Bed Side (MAP)(DRG NO FD/E6/MAP/15(R) (i) Pipe shall be 18mm MS square pipe (18 gauge) black powder coated. (ii) Top and back portion above top of Table bed side shall be of 18mm thick Prelaminated particle board (one side decorative finish shade as approved by GE and other side white balancing lamination) as specified. Standard PVC edging (minimum thickness 1.6mm) shall be provided alround in top and pull out tray. Back of table bed side shall be of 6 mm thick commercial plywood as per IS-303. (iii) Sides and back of drawers shall be provided with 12 mm thick commercial plywood as per IS-303. Bottom of drawer shall be provided with 6 mm thick commercial plywood. (iv) Movement of Pull out tray and drawers shall be made on teak wood runners. One aluminum anodized handle shall be provided to each drawer. (v) Stoppers shall be 2nd class Hard wood (Sal/benteak/Bijasal/Hollock). (vi) Hard rubber/PVC shoe shall be provided to the bottom of each leg. (vii) All exposed surfaces of timber and plywood shall be French polished. (viii) All joints fixing shall be done in accordance with standard workmanship and specifications. (ix) Rest all as shown on drawing.

Table Center two tier (DRG NO 274) Make - Godrej Model Alic DIMENSION:Overall size shall be 900mm long, 450mm wide and 400mm high. DESCRIPTION: All wood shall be of teak wood. Top of the table shall be of 18mm thick prelaminated MDF board of approved shade with 4mm thick teak wood beading all-round the edges of top.Legs shall be made out of 60mmx30mm in section teak wood and 356 mm high. Bottom rail of teak wood of 20mmx50mm in section and 420mm long shall be provided between legs, widthwise at 100mm above the bottom of legs.The bottom tier shall be fixed on the top of bottom side rails with 50mm long screwss.The bottom tier shall be of 18mm thick prelaminated particle board exterior grade of approved shade with 4mm thick teak wood beading all-round the edges of both the tops.25mm dia hard rubber /PVC rings shall be fixed to the bottom of all legs fixed with 30mm long screws. FINISH:All wood surfaces shall be French polished with high gloss finish Rest all as per drg

Sofa Set 5 Seater (DRG NO FD-281) The set shall consist of one long piece of three seat and two small pieces of one seat each. . Timber work shall be of Ist class seasoned teak wood. Foam shall be 100 mm thick cushion of ‘cool’ foam of 40 density of size 550 mmx525mmx100mm covered with best quality tapestry cloth rate not les than Rs. 350. of approved make. All wood surfaces exposed to view shall be French polished and all as per drg No FD-281 complete all as specified and directed.

Table Dining 08 Persons (FD-273/376) (a) All wood work shall be of 1st class hard wood ( Teak). (b) Irrespective of what is shown in the drawing. Top of table shall be of 18/19 MM thick prelaminated particle board exteiar grade as specified. 4MM thick teak wood edging shall be provided all round. (c) Hard rubber/PVC rings shall be screwed to the bottom of each legs. (d) All exposed surfaces of timber shall be french polished. (e) All joints fixing shall be done in accordance with standard workmanship and specifications. (f) Rest all as shown on drawing and as directed by GE/Engr-in-charge.

PART II STEEL FURNITURE

BED MAP STEEL (DRG NO FD/E6/MAP/08(R) (i) Bed hard shall be manufactured all as per details shown in the drawing. All dimensions, shape and size shall be followed as per drawing. (ii) All square and rectangular MS pipes shall be of thickness 18 gauge. (iii) Top of bed shall be of 12mm thick commercial plywood (unpolished) as per IS-303 (iv) Head board and foot board shall be of 18mm thick Prelaminated particle board (both side decorative finish shade as approved by GE) as specified, screwed to MS strip all as per details shown in drawing. Standard PVC edging (minimum thickness 1.6mm) shall be provided alround in Head board and foot board . (v) Hard rubber/PVC shoe shall be provided to the bottom of each leg. (vi) All exposed steel surfaces shall be painted with two coats of synthetic enamel olive green paint over a coat of zinc chromate steel primer. The welding joints shall be filed smooth before application of primer. The surface shall be thoroughly cleaned and prepared prior to application of paint . (vii) Rest all as shown on drawing.

Chair Writing Map (DRG NO FD/E6/MAP/12) (a) All work shall be of Standard class. All dimensions shape and size shall be followed. (b) Rest all as shown on drawing.

Almirah Large Steel (DRG No FD-1031) (i) Steel Almirah (body, shutter, drawer, locker, vertical partitions and shelves) shall be made out of 1 mm thick mild steel sheet all as shown on drawings. (ii) All joints/welding/fixing shall be done all as shown on drawings and with standard workmanship. (iii) Almirah shall be provided with three way locking device as per ‘Godrej’ pattern .The handle shall be made out of steel chrominium plated as per ‘Godrej’ pattern. 4 lever brass lock 65 mm size shall be provided as per Godrej pattern, of make GODREJ, LINK, HARRISON. (iv) Almirah shall be provided with three numbers adjustable shelves with four compartments (v) One steel chrominium plated handle shall be provided to the drawer. (vi) All steel surfaces internally and externally shall be painted with two coats of synthetic enamel paint (olive green) with spray gun over a coat of zinc chromate steel primer. (vii) The welding joints shall be filed smooth before application of primer. The surface shall be thoroughly cleaned and prepared prior to application of paint. (viii) Rest all as shown on drawing.

ALMIRAH STEEL (MEDIUM) (DRG NO FD-1032) (i) Steel Almirah (body, shutter, drawer, locker, vertical partitions and shelves) shall be made out of 1mm MS plain black sheet all as shown on drawings. (ii) All joints/welding/fixing shall be done all as shown on drawings and with standard workmanship. (iii) Almirah shall be provided with three way locking device as per ‘Godrej’ pattern .The handle shall be made out of steel chrominium plated as per ‘Godrej’ pattern. Six lever brass lock shall be provided as per Godrej pattern. (iv) One steel chrominium plated handle shall be provided to the drawer. (v) Locker of the almirah shall be provided with locking arrangement operated with handle as per Godrej pattern. (vi) All steel surfaces internally and externally shall be painted with two coats of synthetic enamelled paint (silver grey colour) with spray gun over a coat of zinc chromate steel primer. (vii) The welding joints shall be filed smooth before application of primer. The surface shall be thoroughly cleaned and prepared prior to application of paint . (xiii) Rest all as shown on drawing.

BOOK CASE STEEL( DRG NO FD-1028) Item to be fabricated as per drg. Overall size shall be 840mm long, 310mm wide and 1675mm, cold rolled, cold annealed MS sheet 1mm thick to be used for channel base, top, sides, back, bottom, front and shelves. The book case shall be provided with four compartments of equal size. The shutters of each compartment shall be open towards top and slide into the depth of the book case. Two steel handles of 100mm shall be provided to each shutter of the compartment. The locking device shall be provided to each compartment. All joints and welding, fixting shall be done in accordance with standard workmanship. rest all as shown on drawing.

Table Cook House Large (DRG NO FD-1019) DIMENSIONS: Over all size shall be of 900x540x840mm. DESCRIPTION :All steel used in the manufacturing of frame structure shall be of 25mm square MS tube with wall thickness 1.6mm .Top shall be of 25mm thick marble stone slab duly finished and rounded edges.6mm dia MS lugs (04 in nos) shall be provided at top of upper rails through welding for the support of stone top.Hard rubber toes shall also be provided to bottom of each leg.All Dimensions, shape and size shall be followed as per drg. All joints, fixing shall be done in accordance with standard specifications. Rest all as shown on drg. FINISH: All steel surfaces exposed to view when placed in position shall be painted with two coats of silver grey hammer paint internally and extrenally with spray machine after preparation of surfaces.A mark of MES shall also be provided on top left corner of front shutter with visible colour. Painting shall be done with spray machine.Rest all as per drg.

Chair Writing Map (DRG NO FD/E6/MAP/12) (a) All work shall be of Standard class. All dimensions shape and size shall be followed. (b) Rest all as shown on drawing.

Magazine Rack Medium (DRG NO FD-356) DIMENSIONS: Overall size shall be 1200mm long, 800mm high and 100mm wide or deep. DESCRIPTION: Back shall be of 12mm thick MDF board.The vertical partitions(05 in nos) shall also be of 12mm thick MDF board.The horizontal rails of teak wood 10mm thick and 50mm wide (04 in nos) shall be fixed on back as shown on drg .The 16 equal partitions made so far shall be provided with housing faciity for acrylic transparent persepex sheet 3mm thick in slanting in 5mm groove made in vertical paritions.The top left and right back shall be provided with a key plate for hanging purpose.The all edges of MDF board shall be covered with 4mm thick teak wood beading. FINISH:All wood and teak veneer surfaces shall be french polished with high gloss finish.

Board Notice 6'x4' (DRG No FD-99M) DIMENSION:Overall size shall be 6'x4'. DESCRIPTION:25mm x 75mm Teak wood frame with 6mm Thick MDF edging all-round shall be provided as shown on drawing, 19mm thick soft wood board shall be fixed in side the frame over which best quality green baize cloth shall be fixed as shown on drawing.On front side 22mm x 10mm aluminum channel shall be provided in side of particle board frame to house 4mm thick glass shutter. Rest all as per drg. FINISH:All wooden expose surfaces shall be french polished two coats after preparation of surfaces. All Dimensions, shape and size shallbe followed as per drg. All joints, fixing shallbe done in accordance with standard specifications. Rest all as shown on drg.

Table card with 4 chairs :- As per drg No. and directed by GE/Engineer-in-Chief.

Ladder Aluminum 8' Long (DRG NO FD-1025) (i) Aluminium stringers with minimum wall thickness of 3.18mm shall be provided all as per details shown in the drawing. (ii) Rungs shall be of 23 mm dia aluminium pipe with wall thickness not less than 2.43mm. (iii) Hard rubber caps / shoes shall be fixed at the ends of aluminium rungs and stringers as shown on drawing. (iv) Rest all as shown on drawing.

Stool Steel Revolving (DRG NO FD-354) Overall as shown on drawing. Overall size shall be 455mm dia and 600mm high four legs of 25mm dia mild steel sheet pipe legs made to shape of thickness 1.6mm irrespective of what is shown on drawing. 12mm dia mild steel bar ring shall be provided at 150mm from bottom joining four legs as showon drawing. Two cast iron discs shall be provided at top of legs and at 100mm top of legs as shown on drawing and fixed to legs with 6mm dia bolt. 25mm dia threaded steel bolt 255mm long fixed with 6mm thick steel plate 100mm dia and top of 25mm dia threaded bolt shall be provided as shown on drawing the padded seat shall be fixed on 6mm thick, 100mm dia steel plate with screw for which four number holes are provided in steel plate. Padded seat shall be 38mm dia . The bottom of padded seat shall be 30mm soft wood over which a layer of coir shall be provided to give proper shape as shown on drawing. Hessian cloth shall be provided to cover the layer of coir and under the soft wood padded seat. A layer of cotton shall be provided and covered with Rexene cover alround the top and bottom to form the padded seat. All steel surfaces exposed to view when placed in position shall be given two coats of enamel paint over a coat of primer after preparation of surfaces. Hard rubber/PVC toes shall be provided to the bottom of legs.

CHAIR CBA STEEL WITH ARMS (DRG No.FD-75(M) Frame shall be fabricated out of 1.6mm thick MS Conduit 20mm dia made to shape as shown on drawings. Over all size shall be 535mm x 560mm x 900mm. Seat shall be 455mm high from floor.Seat, hand rest and back shall be of teak wood. Canning of seat and back shall be done in Godrej patterns shown on drawings with 2mm wide and 0.4mm thick plastic cane of Shah or Premier Brand. Four Nos. 20 x 3mm flat iron strips to each seat and back shall be provided at bottom and back welded to frame as directed by Engineer-in-Charge to provide the supports to seat and back. Bottom of legs shall have hard rubber shoes. Finishes: Wood surfaces of seat, hand rest and back shall be painted with high gloss back paint before caning. All iron surfaces shall be painted with two coats of synthetic black paint over a coat of primer. Vision shall be French polished.

Table steel 900x900x760mm (DRG No. FD-1009) DIMENSIONS : Overall size shall be 900mlong,900mm wide and 760mm high. DESCRIPTION: Steel frame shall be of 800 mm X800mm X742mm . Four legs shall be of 25mm square mild steel tube of wall thickness 1.6mm. Legs shall be joined together with the top rails of 25mm square mild steel tube of thickness 1.6mm. Top of the table shall be of 18mm thick pre-laminated MDF board with 4mm teak wood edging all round the top of table. Hard rubber/PVC toes shall be provided to bottom of legs. FINISH: All steel surfaces exposed to view when placed in position shall be painted with two coats of silver grey hammer paint internally and extrenally with spray machine after preparation of surfaces.A mark of MES shall also be provided on top left corner of front shutter with visible colour. Painting shall be done with spray machine.Rest all as per drg.

Table 1520x860x760mm (DRG No. FD-1010):- as per drg No. and directed by GE/Engineer-in-Chief

Chair CBA Steel Cushioned (DRG No. FD-2044) :- as per drg No. and directed by GE/Engineer-in-Chief.

Bar Stool Cushioned Steel (DRG No. FD-95/354) DIMENSIONS :The overall height of the stool shall be 900mm after lift . DESCRIPTION:It shall be of revoloving type with 360 degree swivel.The frame shall be of round pipe 1" dia and the frame and base shall be of chromeplated .The stool shall have gas lift and consist of foot rest.The seat sh all be of soft cushion 50 mm thick fitted with best quality tapestry/leatherite cloth.As per sample approved by GE. MAKE:-Godrej Model-FUS1M4HC13RSXTR

Table Pantry (DRG No. FD- 1020) DIMENSIONS: Over all size shall be 900mm long. 550mm wide and 840mm high. DESCRIPTION: Size of steel frame shall be 880mmx815mm. Legs shall be four in numbers. Legs shall be of 25mm square mild steel tube of wall thickness. All steel sheet used for drawers and side overing of drawer and for support of drawer shall be of mild steel and 1mm thick. Top of table shall be 25mm thick polished Kotah stone slab in one piece. Legs shall be provided with hard rubber/PVC toes at bottom. FINISH :All steel surfaces exposed to view when placed in position shall be painted with two coats of silver grey hammer paint internally and extrenally with spray machine after preparation of surfaces.A mark of MES shall also be provided on top left corner of front shutter with visible colour. Painting shall be done with spray machine.Rest all as per drg.

Teapoy Verandah (DRG No. FD- E6/MAP/17) (i) Frame, stiffeners, legs ,etc. shall be made of 18mm square MS pipe of thickness 18 gauge. (ii) Top of Teapoy shall be of 18mm thick Prelaminated particle board (one side decorative finish shade as approved by GE and other side white balancing lamination (iii) Base tray made with 5mm dia mild steel wire/rod shall be provided (iv) 4mm thick teak wood edging shall be provided alround. (v) FINISHES: All steel surfaces, exposed to view when placed in position shall be given two coats of enamel paint over a coat of primer with spray machine after preparation of surface. (vi) Rest all as shown on drawing

Rack 6 tier Steel (1800x900x500mm) (DRG No. FD-1038) DIMENSIONS: Overall size shall be 915mm long,610mm wide and 1905mm high. DESCRIPTION :The entire rack shall be made of 1mm mild steel sheet.The sides shall be provided with 40x40x4mm angle iron welded to 1.00mm thick MS sheet.75x75x3mm thick Flat iron cut to shape shall be welded at front corner.All partitions shall also be made of 1mm thick mild steel sheet and shall be riveted to side of rack . All Dimensions, shape and size shall be followed as per drg. All joints, fixing shallbe done in accordance with standard specifications. Rest all as shown on drg. FINISH: All steel surfaces exposed to view when placed in position shall be painted with two coats of silver grey hammer paint internally and extrenally with spray machine after preparation of surfaces.A mark of MES shall also be provided on top left corner with visible colour. Painting shall be done with spray machine.Rest all as per drg.

Table Office Clerk steel (DRG No. FD-1004) DIMENSIONS : Overall size shall be 1200mm long, 610mm wide and 760mm high. DESCRIPTION:Steel frame shall be of size 1160x570x742mm .four legs of 25mm mild steel tube of 1.6mm wall thickness shall be provided. Top of legs shall be joined together with 25mm square mild steel tube of wall thickness 1.6mm in long and short sides. Two short stiffeners of same size shall be provided at 130mm from bottom of legs. One long stiffener shall also be provided to the middle of short stiffeners. Three drawers of equal size shall be provided on the right hand side above the stiffener at 130mm high with overall size of 350mm wide and 430mm high and 410mm deep..The top of table shall be provided with pre-laminated MDF board of 18/19mm thick with teak veener shade and 4mm thick teak wood edging alround the table .Hard rubber/PVC toes shall be provided to the legs.Locking device shall be provided to drawers. FINISH: All steel surfaces exposed to view when placed in position shall be painted with two coats of silver grey hammer paint internally and extrenally with spray machine after preparation of surfaces.A mark of MES shall also be provided on top left corner of front shutter with visible colour. Painting shall be done with spray machine.Rest all as per drg.

Trestle Store Room Steel (DRG No. FD-1043) DIMENSIONS: Overall size shall be 2440mm long, 600mm wide a 300mm high. DESCRIPTION:Two long angle iron 40mmx40mmx6mm of mild steel 1980mm long shall be provided 520mm apart at bottom connected with 50mmx3mm iron bracing, four in numbers, and equally spaced with 50mmx50mmx6mm iron.Rest all as per drg. FINISH: All Steel and iron work surfaces shall be painted with two coats of enamel paint over a coat of primer with spray machine after preparation of steel surfaces on exposed to view when placed in position.

Side Rack with Tray 3 Tier Four Spaces (STEEL) (DRG No. FD-321):- Overall size shall be 1120mm long, 355mm wide and 810mm high. Angle iron 40mmx40mmx3mm legs shall be provided at four corners. The bottom shelf shall be at 100mm from bottom of legs made 1mm thick mild steel sheet bent 20mm on all sides and again bent inwards up to 20mm. The top shelf shall be provided at 50mm from top of legs and shall have four spaces of equal size. The back, sides and intermediate partition shall be of 1mm thick mild steel sheet. The top shelf shall be of 1mm thick mild steel sheet bent 20mm on all sides and bent in wards up to 20mm The middle shelf shall be provided equally spaced from top and botom and shall be 1mm thick mild steel sheet bent 20mm on all sides and bent inwards up 20mm. The lower space below the trays shall be open from all sides. all steel surfaces exposed to view when placed in position shall be painted with automotive paint over a coat of primer after preparation of surfaces as directed by Engr-in-charge. Painting shall be done with spray machine.

Chair Umpire Steel :- As per drg No. and directed by GE/Engineer-in-Chief.

Bench workshop1800x900x760mm (DRG No. FD- 145M) DIMENSIONS :- Over all size shall be of 1800x900x760mm. DESCRIPTION :- Four legs shall be of 32mm square mild steel tube of wall thickness 1.6mm.Size of the steel frame shall be 1700mmx 800mm x720mm. Legs shall be 720mm high.Top of legs shallbe joined together in long and short sides with 32mm sq mild steel tube ..Two Short stiffeners of 32mm mild sq steel tube shall be provided at 100mm from bottom of legs in short sides.A drawers shall be provided at right hand side of the table with locking arrangement,the drawer and bearer for drawer shall be made of 1mm thick MS sheet . Hard rubber shoe shall be provided for legs. The top of the table shall be of 40mm thick IInd class hard wood shisham/sal wood and shall be given with three coats of Ist class oil paint over a coat of primer. FINISH:-Top shall be painted in colour with two coats of oil paint and steel portion shall be painted over a coat of primer on steel frame. All joints/welding, fixing shall be done in accordance with standard specifications. Rest all as shown on drg.

PART III TRADE PATTERN FURNITURE

BATH MAT PVC (FD/MAP/E6/07) (i) All PVC work shall be of standard class PVC. All dimensions, shape and size shall be followed as per drg. (ii) Hard rubber shoe shall be provided to the bottom of each leg. (iv) Rest all as shown on drawing No FD/MAP/07 complete all as specified and directed. (iii) PVC Bath Mat shall be of make: Blow plast/Neel Kamal/Supreme /Cello / Polyset/Brite/syntex.

Chair PVC Cushioned:- (i) All PVC work shall be of standard class PVC. All dimensions shape and size shall be followed as per drg. (ii) PVC Bath Mat shall be of make blow plast/Neel Kamal/Supreme/Cello/Polyset/Brite/syntex. (iii) Rest all as per drg No. and directed by GE.

PLATE RACK 900x750x300mm (a) Overall size shall be 900mmx750mmx300mm teak wood throughout. Rest all as per drg and as specified. (b) All wooden surface exposed to direct vision shall be given two coats of white synthetic enamel paint over a coat of pink primer.

Deep Freezer 200/210 Ltr Make Blue Star (safe Meat & Milk)

Hot Case Large Drg No.FD 363) :- Overall size shall be 1350mm long, 540mm wide and 1140mm high. All wood shall be of first class hard wood teak. Legs shall be 45mmx45mm in section at top and 30mmx30mm in section at bottom, made to shape, as shown on drawing and 100mm high. Legs shall be four in numbers. Legs shall be joined together by 19mmx40mm stiffeners in long and short sides in such a way that top of stiffeners shall flush with top of legs. Bottom of hot case hsall be of 19mm thick wooden planks fixed on top of legs. The length of plank shall be 1330mm the width shall be 520mm. The numbers of planks in 520mm width shall be as directed by Engineer-in-charge. The width of planks shall not be less than 150mm. The sides and back shall be of 19mm thick particle board of teak veneer face outside and commercial on other. Front shall have shutters of 19 mm teak veneer particle board. Top shall have teak wood frame of 75mmx19mm long rails, two in numbers, 1330mm long joined two sides short rails 520mm long. Four numbers 19mm x 75mm stiffeners shall be provided joining the two long rails as directed by Engineer-in-charge. Irrespective of what is shown on drawing 996mm high partition vertical shall be provided in the front of shutters to support the front shutters. Two shutters on left hand side and one shutter on right hand side shall be provided as shown on drawing. Plain asbestos sheet shall be provided to the soffit of hot case. Aluminium sheet of 22 gauge shall be fixed to bottom, sides, soffit and shutters of hot case. Four numbers 12mm dia pins to support the flat iron frame of one shelf shall be provided as directed by Engineer-in-charge. Two shelves of welded mesh fixed on 12mmx3mm flat iron frame shall be provided. Top shall have 25mm thick polished stone slab on one piece of 1350mm long and 540mm wide. 30mm dia recessed knobs shall be provided, two to left shutter and one for right shutter. Ball spring catch shall be provided to each shutter. Shutters All wood and particle board shall be French polished with high gloss finish. Steel surfaces shall be painted with two coats of enamel paint ober a coat of primer after preparation of surfaces as directed by Engineer-in-charge. Aluminium sheet surfaces shall remain untreated.

Table Computer DRG No. FD/E6/MAP/03 DIMENSIONS :-Overall size of top shall be 900mm long,561.20 mm wide and 750mm high. DESCRIPTION:-All prelaminated particle board used in manufacturing of top ,shelves,drawers,tray shall be of 18mm thick prelaminated MDF board.The frame of table shall be of 25MM square pipe of wall thickness not lss than 1.6mm.The top of table shall be provided with 4mm thick teak wood beading.The legs shall be made out of 25mmx50mm MS rectangular CR pipe of 18 guage.Each leg shall be provided with rectangular PVC cover made to shape on front sides only.The drawers shall be provided with telescopic channel 300mm long.The legs shall also be provided with nylon buffers .Rest all as per drg. FINISH:- All wood surfaces shall be French polished with high gloss finish Rest all as per drg.

Table Laundry Drg No. FD-85(M):- As per drg No. and directed by Engineer-in-Chief.

Rack Laundry Drg No. FD-85(M):- As per drg No. and directed by Engineer-in-Chief.

Chair Computer Drg No FD/E6/MAP/01:- The Base pedestal assembly of chair computer shall be of dia 700mm and 1060mm high .The pedestal assembly shall be provided with injection molded in black 30% glass filled nylon. A 10.5mm dia forged bright Zinc plated MS Castor Pin is of press fitted into each prong for holding the castors. The seat and back of the chair computer shall be made of 12mm thick hot pressed plywood upholstered with fabric and moulded polyurethane foam. The back form shall be designed with contour lumber support for extra comfort with PVC lipping allround.The back rest shall be adjustable and consist of drop lift mechanism and shall be adjusted in the insert .It shall be scratch and weather resistant. Rest all as per drg.and as per sample approved by BSO/GE

Daya Nand Jindal

M/s Rajesh Kumar Jain