SPL REPAIR TO BLDG NO T 35 OF SCC BHOPAL WIRE MESHING WIRE NETTING OF TOP FLOOR BALCONIES AT BLDG NO P 341 P 342 OF SCC BHOPAL PROVN OF INTERLOCKING TILES IN NCC SINGLE OFFR ACCN AND INTERLOCKING DRAIN GRATING OF P 48 AT SI LINES UNDER GE BHOPAL

Amount

Note :(i) Please refer Sch A/ BOQ Notes before quoting the tender for all phases/ items mentioned below. (ii) Amount of Schedule of credit shall be deducted offline

Taking down chowkats or frames exc 1.50 Sqm but n.exc 4 Sqm with shutters (without taking off shutters from the frame) complete all as specified and directed.

Taking down chowkats or frames n exc 1.50 Sqm with shutters (without taking off shutters from the frame) complete all as specified and directed.

Taking down shutters of any descripition exc 1 sqm and n exc 2 sqm each complete all as specified and directed.

Taking down shutters of any descripition n exc 1 sqm each complete all as specified and directed.

Taking down shutters and refixing in same opening of any descripition exc 1 sqm and n exc 2 sqm each complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connections of any descrition complete all as specified and directed.

Taking up or down 20mm bore steel tubing and connections of any descrition complete all as specified and directed.

M&L for cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc; and cutting chases for concealed water tubing or concealed conduit wiring, etc and making good, cutting not exc 10cm girth complete all as specified and directed.

S&F of tubes 15mm dia, `medium grade' galvanised, with all fitting and fixed to walls and ceilings or laid in floors complete all as specified and directed.

S&L of 16 mm dia CPVC pipes SDR 11 and plain CPVC SDR 11 fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed.

S&F of tubes 20mm dia, `medium grade' galvanised, with all fitting and fixed to walls and ceilings or laid in floors complete all as specified and directed.

M&L for Endura joint free colour tiles 9 to 10 mm thick (square/rectangular) area of each tiles not exceeding 0.11 sqm as in floors etc; set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tiles complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7-8 mm thick (square/rectangular) area of each tile exc 0.11 sqm but not exc 0.18 sqm as in floors etc; set and jointed in white or colour cement to match the surface of the tile complete all as specified and directed.

M&L for glazed ceramic coloured tiles joint free in vertical surfaces 350x250x7mm / 450x350x7mm thick such as dados, skirting etc; with and including 10mm thick rendering backcoat in CM 1:4; set and jointed in white or colour cement to match the surface of the tile complete all as specified and directed.

M&L for providing, cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, copings, kneelers, apex stones, bed plates and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

M&L for PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in foundation, sub base, mass filling etc complete all as specified and directed

Demolition of flag stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and directed.

M&L for granite stone work (of any type) 20mm thick, machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing complete all as specified and directed.

M&L for 15mm thick screed bed or bedding layer of cement mortar 1:4 for laying floor finish, finished even and rough complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

M&L for making good under cills and over archs, lintels and bressummers including all pinning where necessary in cement mortar in 1:6 complete all as specified and directed.

S&F of providing powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (fixed portions) with extruded built up standard tubular sections/appropriate sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc; aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, C.P.brass/ stainless steel screws, etc; and fixed complete all as specified and directed.

S&F of 4.8mm thick plain sheet glass ordinary quality exc 0.50 Sqm in each pane complete all as specified and directed.

S&F of stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples/ screws complete all as specified and directed.

S&F of 100 mm size butt hinges medium weight cold rolled mild steel and fixed complete all as specified and directed.

S&F of 75 mm size butt hinges medium weight cold rolled mild steel and fixed complete all as specified and directed.

S&F of 100 mm butt hinges, extruded alluminium alloy with galvanised mild steel hinge pin, anodised, type C-21 and fixed complete all as specified and directed.

S&F of 150 mm long aluminium handles, cast type, anodised and fixed to shutters complete all as specified and directed.

S&F of 100 mm long aluminium handles, cast type, anodised and fixed to shutters complete all as specified and directed.

S&F of 150 mm long aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F of 100 mm long aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F of 35 mm factory made single extruded WPC (Wood Polymer Composite) solid plain glazed shutter door of 35 mm size open rebated and prepared to receive gauze, etc.(without sash bars) edge of framing plain, chamfered or rounded, etc; size of members of shutters comprising of virgin polymer of K value 58-60(Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm 2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws complete all as specified and directed. (Note : Wiremesh Shall be measured and paid separetely).

S&F of machine moulded and factory made 40 mm thick flush shutters, solid core construction, with block board core and ply wood face panels, decorative type on both sides and fixed to chowkats complete all as specified and directed. Make: A-1 TEAK, Rajshree, M.P. wood

S&F of 0.90 mm thick decorative laminate type-1 of surface finish, any colour and pattern as approved and fixed with approved adhesive as per manufacturers instructions complete all as specified and directed.

S&F of pressed steel frames of size 165x60 mm for fixing of panelled and fly proof doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and directed.

S&F of 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed and fixed complete all as specified and directed.

S&F of anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing, approved anodised aluminium standard section around the opening, all complete as per requirement for windows, vintilators complete all as specified and directed.

S&F of 15 mm bore wash basin mixutre, centre hole, mixing hot & cold water, fancy type, cast copper alloy, chromimum plated with capstan head, screwed down high pressure, screwed for iron pipe etc and fixed in repairs complete all as specfied and directed. Make: Jaquar Cat No: 5001B of equivalent in Cera / Hindware

S&F of handshower (health faucet) with 8 mm dia and 1 meter long flexible tube and wall hook fixed in repairs complete all as specified and directed. Make: Jaquar Cat No: 573 of equivalent in Cera / Hindware

S&F of stainless steel chromium plated grating doom 100 mm dia with waste hole and fixed in floors complete all as specified and directed.

S&F in repairs PVC low level flushing cistern of 10 Litres with all internal fittings incl flush pipe and fixing to supply pipe complete all as specified and directed.

S&F of PVC connection 15mm size with brass nuts of length 450 mm and fixed complete all as specified and directed.

S&F in repairs 15 mm bore stop cock, cast copper alloy, chromium plated, screwed down high pressure with capstan head, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repairs 15 mm bore bib taps, cast copper alloy, chromium plated, screwed down high pressure with capstan head, screwed for iron pipe and fixed complete all as specified and directed.

S&F of factory made single extruded WPC (WoodPolymer Composite) solid door/ window/ ceosetory windows & other frames/ chowkhat of size 65x100 mm comprising of virgin PVC polymer of K value 58-60 (suspension grade), calcium carbonate andnatural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance tospread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and directed.

S&F of factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35 mm size comprising of virgin polymer of K value 58-60(Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws complete all as specified and directed.

S&F of 75mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and direcetd.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc; complete all as specified and directed. (measured overall as fixed along the centre line over fitting and accessories)

S&F of 75 mm bore PVC (SWR) pipes single socketed in any length with rubber rings joints laid in trenches complete all as specified and directed.

S&F of 110 mm bore PVC (SWR) pipes single socketed in any length with rubber rings joints laid in trenches complete all as specified and directed.

S&F of 75mm bore PVC (SWR) pipes single socketed in any length with rubber rings joints laid in trenches complete all as specified and directed.

S&F of 110 mm bore PVC (SWR) bend and fixed with solvent cement complete all as specified and directed.

S&F of 75 mm bore PVC (SWR) branch piece single (Y) equal or unequal bend and fixed with solvent cement complete all as specified and directed.

S&F of 110 mm bore PVC (SWR) branch piece single (Y) equal or unequal bend and fixed with solvent cement complete all as specified and directed.

S&F of 75 mm bore PVC (SWR) junction single (single 'T') equal or unequal and fixed with solvent cement complete all as specified and directed.

S&F of 110 mm bore PVC (SWR) junction single (single 'T') equal or unequal and fixed with solvent cement complete all as specified and directed.

S&F of 75 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F of 110 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F of plastic water closet seat, white, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S&F in repairs tubular towel rail, brass chromium plated 20 mm dia, D type, 60 cm long between flanges complete all as specified and directed.

S&F in repairs of vitreous china wash down water closet pan (pedestal pattern), white (excluding flushing cistern and flush pipe) including connection to drain (or outgoing pipe) and to flushing pipe, anti syphonage pipe, etc. complete all as specified and directed.

S&F in repairs brass chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe of 15 mm bore complete all as specified and directed.

S&F in repairs corner sheet glass shelf assembly consisting of 8 mm thick sheet glass shelf, 300 mm long railing with brass chromium plated brackets complete all as specified and directed.

S&F of sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf, 12 cm wide with brass chromium plated bracket guard and railing 60 cm long complete all as specified and directed.

S&F in repairs 5 mm thick looking mirror approved quality of any size, mounted on 6mm thick plywoord and decorative type egde bedding alround and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed.

S&F in repairs angle cock, cast copper alloy, chromium plated fancy type, with capstan head, screwed both ends for iron pipe of 15 mm bore and fixed complete all as specified and directed.

M&L of 15 mm thick rendering in cement mortar 1:4 on fair faces of bricks wall surfaces, finished even and smooth without using extra cement using water proofing compound as per manufacturer instruction complete all as specified and directed. (Note: Water proofing compound shall be measured and paid seperately)

M&L for 15mm thick rendering in CM 1:6 on any face of brick walls/ concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

Supply only integral water profing compound ISI marked complete all as specified and directed.

Taking down cement plaster, terrazzo/cement dado, skirting etc of any description on brick/stone walls, concrete surfaces etc including racking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

M&L for preparation of newly plastered surface of walls and applying two coats of oil emulsion distemper over a coat of white cement based putty complete all as specified and directed.

M&L for preparation of new plastered surface and applying two coats of exterior weather proof water base emulsion paint (white/tinted) over and including one coat of white cement based putty complete all as specified and directed.

M&L for complete removal of existing treatment of walls and applying two coats of exterior weather proof water base emulsion paint (white/tinted) over and including a coat of primer complete all as specified and directed.

M&L for complete removal of existing treatment of walls and applying two coats of oil emulsion distemper over one coat of white cement based putty complete all as specified and directed.

M&L for providing 3mm thick wall care putty on wall/ceiling, finished even and smooth complete all as specified and directed.

M&L for 75 mm thick plain cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in plinth protection, finishing the surface even and smooth without using extra cement laid in bays n exc 2 m in length and joints filled with bitumen mastic 1:3 complete all as specified and directed.

Demolition of concrete in ground floors and pavings (un reinforced) n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Demolition of brick work or stone masonery built in cement mortar complete all as specified and directed.

M&L for brick work with fly ash modular bricks, straight or curved on plan to any radius in half brick thick walls built in ceement mortar 1:6 complete all as specified and directed.

M&L for brickwork with fly ash modular bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

S&F in repairs 25mm dia stainless steel drapery rod type including brackets (02 Nos) of approved quality complete all as specified and directed.

Dismentling of asbestos cement (corrugated, semi corrugated, etc.) sheets as in roof coverings including fillets complete all as specified and directed.

Dismantling timber rails, posts, rafters, purlins, etc. under 40 Sq cm in section in framed work complete all as specified and directed.

Dismantling timber scantling 40 sq cm and over in section, in any position in unframed work complete all as specified and directed.

S&F of mild steel rolled section/tubular sections in purlins, cross beams, rafters, posts etc. including connected cleats, hold fasts etc of grade conforming to Fe 410-O or Fe 310-O complete all as specified and directed.

S&F of hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts including necessary drilling bolting as riveting etc and similar work to Fe 410-S or Fe 310-S complete all as specified and directed.

S&F of pre-painted galvalume aluminium zinc coating GI based corrrugated steel sheet 0.50 mm thick of any color having tensile strength of 550 Mpa as in roof covering /cladding to walls and fixed with self-tapping screws on angle iron frame of each side complete all as specified and directed.

S&F of pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any color having tensile strength of 550 Mpa as in roof covering /cladding to walls and fixed with self-tapping screws on angle iron frame of each side complete all as specified and directed.

M&L for preparation of old painted surfaces of steel and iron surface of any description not otherwise described and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new steel surface of any description not otherwise described and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F of mild steel framed work such as grills, gratings etc; with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and directed.

S&F of machine pressed precast concrete inter locking paver block (Reflective type) in any shape and size confirming to IS-15658-2006 of 60 mm thickness M-35 grade with grey cement and pigment complete all as specified and directed.

Cutting holes in brick walls exc half brick but not exc one brick in cement mortar ore cement lime mortor for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required complete all as specified and directed.

S&F in repairs vitreous china squatting pan of Orissa pattern 580x440 mm white with integral foot rests (excluding flushing cistern and flush pipe) including all making connection and making good to the floor complete all as specified and directed.

M&L for machine cut kota stone slab flooring 20-22mm thick in single piece over and including 20mm thick screed bed in cement mortar 1:6, laid & jointed with grey cement slurry mixed with pigment to match the shade of the platform and similar work including rubbing & mirror polishing and required moulding work on exposed thickness complete all as specified and directed.

M&L for machine cut kota stone slab flooring 20-22mm thick over and including 10mm thick rendering in cement mortar 1:4 as in riser of steps, skirting, dado and pillar etc; laid & jointed with grey cement slurry mixed with pigment to match the shade including rubbing & mirror polishing complete all as specified and directed.

S&F of galvanised cold rolled steel section framed work size 600x600mm grid size 24x38x0.60mm tee (bottom precoated) and 24x24x0.50mm thick wall angle galvanised cold rolled steel section including expansions fasteners as in ceiling as per site requirement complete all as specified and directed. (Make : Gabson or equivalent as approved by GE)

S&F of 6mm thick asbestos free calcium silicate board of size 600x600mm fixed to frame work of galvanised cold rolled steel as in ceiling with and including applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

S&F of 300mm long ordinary MS rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp,insultion, etc) or insulation boards/ slabs /blankets any thickness including cover fillets complete all as specified and directed.

M&L for preparation of old decorated surface of walls and applying one coat of cement based paint complete all as specified and directed.

M&L for preparation of old decorated surfaces of walls and applying one coat of oil emulsion distemper complete all as specified and directed.

Excavation in trenches n exc 1.5 m wide and n exc 1.5 m in depth beyond; for foundation, etc. or for shafts, wells , cesspits, manholes, pier holes etc n exc 10 sqm on plan and not 1.5 m depth and getting out hard/dense soil complete all as specified and directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in hard/ dense soil complete all as specified and directed.

M&L of hardcore of broken stones of guage n.exc 63mm, deposited, spread and leveled in layers n exc 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for moorum/red bajri filling in floors or paving, laid in layers n.exc 15cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:4 on any faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for clean dry sand filling under floor/pavement or in foundation including watering and consolidation complete all as specified and directed.

Returing filling including spreading, levelling, watering and well ramming in layer not exc 25 cm complete all as specified and directed

Removel of excaveted material n.exc 50 m and deposited where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.

M&L for providing precast cement concrete 1:2:4, type B-0 (using 12.5mm graded stone aggregate) as in louvres and jallies, 25mm thick (measured solid), including all mould ings but including frame fixed by cement motar of 1:4 complete all as specified and directed

M&L for mild steel TMT bars 6 to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) of any type complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

Dismantling/ taking down of unserviceable old existing service/ submain wire of any size complete all as specified and directed.

Dismantling/ taking down of unserviceable distribution boards with MCBs complete all as specified and directed.

Disconnecting, dismantling & taking up or down existing hot water geyser of any description and in any position 25/ 35/ 50 Ltrs capacity and re-fixing it in its existing position after cleaning complete all as specified and directed.

Taking dow carefully serviceable/ unserviceable exhaust fans of any size from its position and refixing on its position properly after cleaning complete all as specified and directed.

Taking down carefully ceiling fans of any size from its position and refixing on its position properly after cleaning complete all as specified and directed.

Taking down LED tube light fitting bright 18 Watt, slim elegant design and refixing the same in new location after cleaning and making connection with new 3 core 23/0.0076 insulated copper wire from celing rose to fitting connector complete all as specified and directed.

M&L for concealed point wiring with 1.50 sqmm (nominal area), FRLS PVC insulated, unsheathed, single core multi-stranded copper conductor cable, 1100 volts grade, ISI marked, drawn through and including concealed medium grade PVC conduit not less than 20 mm dia, ISI marked, with all accessories (PVC Casing and caping of size 25 mm, ISI marked with complete accessories to be used wherever wiring to be run on ceilings and concrete surfaces) including one run of 1.5 sqmm FRLS PVC insulated, unsheathed, single core multi stranded copper conductor (Green colour cable) as earth continuity wire connected to common earth dolly including sunk sheet steel terminal box made out of 1.20 mm thick and not less than 60 mm in depth GI/MS/ pressed steel terminal box to be concealed in wall, duly painted with two coats of anti corrosive black bituminous paint over a coat of red oxide primer in and out sides including 2.8mm thick laminated hylem sheet cover, ISI marked for mounting of fittings like switches, sockets, fan regulators etc. fixed with galvanised screw and cup washers complete all as specified and directed for the following points:-

(a) One light point / fan/ exhaust fan/ bell point

(b) One 3 pin 5 Amp socket outlet on same board.

(c) One 3 pin 5 Amp switch socket combination on independent board.

M&L for concealed point wiring for 3 pin 15 Amp switch socket combination on independent board with 2.50 sqmm (nominal area), FRLS PVC insulated, unsheathed, single core multi-stranded copper conductor cable, 1100 volts grade, ISI marked, drawn through and including concealed medium grade PVC conduit not less than 20 mm dia, ISI marked, with all accessories (PVC Casing and caping of size 25 mm, ISI marked with complete accessories to be used wherever wiring to be run on ceilings and concrete surfaces) including one run of 1.5 sqmm FRLS PVC insulated, unsheathed, single core multi stranded copper conductor (Green colour cable) as earth continuity wire connected to common earth dolly including sunk sheet steel terminal box made out of 1.20 mm thick and not less than 60 mm in depth GI/MS/ pressed steel terminal box to be concealed in wall, duly painted with two coats of anti corrosive black bituminous paint over a coat of red oxide primer in and out sides including 2.8mm thick laminated hylem sheet cover, ISI marked for mounting of fittings like switches, sockets, fan regulators etc. fixed with galvanised screw and cup washers complete all as specified and directed.

All as per item No. 122.00 here-in-before but with using 4.0 Sqmm cable.

S&F of switch piano flush type single pole one way 5 Amps complete all as specified and directed.

S&F of socket outlet 2 in 1, 5 pin flush type 5 Amp complete all as specified and directed.

S&F of switch socket combined outlet, 6 pin flush type 15 Amp complete all as specified and directed.

S&F of ceiling rose surface bakelite 65mmm dia, three terminal complete all as specified and directed.

S&F of stepped type electronic fan regulator complete all as specified and directed.

S&F of lamp holder, PVC/polycorbonate type with back plate with and including LED bulb retrofit type 9/10 watts complete all as specified and directed.

S&F of LED light fitting 1 x 20 watts, 220 volt, AC, decorative box type with driver, holder including LED tube light and connecting with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F of factory made epoxy coated powder coated distribution board TPN, 4 way (VTPN MCCB DB) and space for MCCB as incomer, with metal door (IP-43 protection) fabricated from CRCA sheet and fixed semi flush to wall and suitable for universal mounting and including isolated Neutral Bar, Insulated busbar assembliy, neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with knockouts complete all as specified and directed.

S&F of MCCB, 125 Amps, 3 pole of breaking capacity 36 KA including making connection with suitable size copper lugs complete all as specified and directed.

S&F of sheet metal enclosure for MCB, DB, double door, 8 way, 240 volts, 200 Amps rated bus bar, dust and vermin proof suitable for incorporation gof MCB and isolators duly concealed in walls complete all as specified and directed.

S&F of MCB, SP, 6 to 32 Amps, 240 volts, 10 KA breaking capacity, 'C' curve including connection with suitable size copper lugs complete all as specified and directed.

S&F of MCB, DP, 40 to 63 Amps, 415 Volts, 10 KA breaking capacity, 'C' curve including making connection with suitable size copper lugs complete all as specified and directed.

M&L for sub main wiring with two single core PVC insulated unsheathed cable 1100 volts grade, multistranded copper conductor FRLS cable of 4.0 Sqmm drawn in and including non metallic rigid PVC conduit of 25 mm dia, ISI marked including one run of PVC insulated unsheathed, multistranded copper conductor FRLS cable of 4.0 Sqmm (Green colour) as earth continuity conductor cable connected to earth dolly complete all as specified and directed. Note: Three runs of cable shall be measured as a single length.

S&F of building security light fitting of 30 Watt LED type, pressure die cast aluminium housing and heat resistant toughened glass with frame protection and better optics for uniform distribution including 32 mm bore GI light grade pipe of approx 1.5 mtr length with brakets, nuts, bolts, washers etc; and making necessary connnections with twin core 1.5 Sqmm copper cable from ceiling rose to fitting complete complete all as specified and directed.

M&L for earthing complete with galvanised steel plate earth electrode 600 x 600 x 6 mm thick, burried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level, connected to earthing lead of 32 x 6 mm galvanised mild steel strip by means of bolts, nuts, check nuts and washers from earth plate to test point upto 7.5 meter including necessary concrete chamber in cement concrete M-15 (nominal mix), precast RCC cover slab in cement concerete M15 (Normal Mix) of size 40 x 40 x 5 cm duly reinforced with 8 mm dia TMT bars @ 150 mm C/C both ways with one handle for lifting, GI funnel, GI wire mesh filter, 20 mm dia GI pipe medium grade for watering, 40 mm dia GI Pipe medium grade for protection of earthing lead, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil/strate and testing complete all as specified and directed.

S&F of sheet metal enclosure with socket plug top with two pin and earth plug and socket with and including 01 MCB, SP, 20/25 Amps, 240 Volts and making necessary connection complete all as specified and directed.

S&F of 250mm sweep exhaust fan, steel body, AC single phase, 230 Volts with blades, frame and louvers including connecting with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Deduct Schedule of credit (calculation will be done off line) Rs. 55033.00

PADAMSHRI CONSTRUCTION CO

M/S RAKESH TRADERS

M/s H V Infra Projects

AJIT ENTERPRISES

SHIV SHANKAR MISHRA

POONAM ELECTRIC INDUSTRY