MMPNA/2023-24/98

Amount

Maintenance of WBM road including filling up of pot holes, ruts and rectifying corrugated surface, damaged edges and ravelling as per technical specification Clause 1906.

Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502 (Provided only on WBM surface).

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared dry and hungry bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.

20mm thick open graded premix carpet using Bituminous Binder mixing with processed waste plastic (as per IRC -SP-98-20130 by replacement of 8%bitumen binder weight providing and laying and rolling of 20mm thick open graded premix carpet it ( thickness not less than 20mm at any place) composed of 13.2mm graded aggregate size @ 0.18 cum per 10 sqm & 11.2mm graded aggregate size & 0.09 cum per 10 sqm using bituminous binder @ 13.432 kg per 10 sqm ( i.e 92 % of standard bitumen and 8% waste processed plastic by weight shall be used for coating aggregate after heating ) as per IRC : SP:98:2013 layinh to required line , grade and levelto serve as finished to required level and graded as per technical specification cl 508 to be followed by seal coat of either type A , type B or Type C as per technical specification , Bitumen VG 30.

SealCoat : Providing and laying sealcoat sealing the voids in a bituminous surface laid to the specified levels , grade and cross fall using Type A , Type B and Type C as per technical specification cl 510 , Case -III Type C (II) Bitumen (S-65).

Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes and conforming to the MoSrt&H specifications

Maintenance of Hume Pipe Culvert (1 No) Brik masonry work in cement mortar in foundation of wall complete excl. pointing and plastering as per drawing and technical specification clause 1100(in prop. 1:4)

Plastering with cement mortar(1:6) 15mm thick on brick work for substructure as per technical specification

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 801. i) 800mm x 600mm rectangular

Providing & fixing retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on mild steel angle iron post 75mm x 75mm 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450mm x 450mm x 600mm,600 mm below ground level as per drawings and technical specification Clause 801 ii) 600mm circular

Providing & fixing retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on mild steel angle iron post 75mm x 75mm 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450mm x 450mm x 600mm,600 mm below ground level as per drawings and technical specification Clause 801 iii) 600mm equilateral triangle

Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1

Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC : 8 fixing in position including painting and printing etc as per drawing and technical specification cl 1703 (iv) 200m stone pre cast

Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC : 8 fixing in position including painting and printing etc as per drawing and technical specification cl 1703 (v) Ordinary KM Stone (Pre cast)

Maintenance of WBM road including filling up of pot holes, ruts and rectifying corrugated surface, damaged edges and ravelling as per technical specification Clause 1906.

Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502 (Provided only on WBM surface).

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared dry and hungry bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.

20mm thick open graded premix carpet using Bituminous Binder mixing with processed waste plastic (as per IRC -SP-98-20130 by replacement of 8%bitumen binder weight providing and laying and rolling of 20mm thick open graded premix carpet it ( thickness not less than 20mm at any place) composed of 13.2mm graded aggregate size @ 0.18 cum per 10 sqm & 11.2mm graded aggregate size & 0.09 cum per 10 sqm using bituminous binder @ 13.432 kg per 10 sqm ( i.e 92 % of standard bitumen and 8% waste processed plastic by weight shall be used for coating aggregate after heating ) as per IRC : SP:98:2013 layinh to required line , grade and levelto serve as finished to required level and graded as per technical specification cl 508 to be followed by seal coat of either type A , type B or Type C as per technical specification , Bitumen VG 30.

SealCoat : Providing and laying sealcoat sealing the voids in a bituminous surface laid to the specified levels , grade and cross fall using Type A , Type B and Type C as per technical specification cl 510 , Case -III Type C (II) Bitumen (S-65).

Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes and conforming to the MoSrt&H specifications

Maintenance of Hume Pipe Culvert (3 Nos) Brik masonry work in cement mortar in foundation of wall complete excl. pointing and plastering as per drawing and technical specification clause 1100(in prop. 1:4)

Plastering with cement mortar(1:6) 15mm thick on brick work for substructure as per technical specification

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 801. i) 800mm x 600mm rectangular

Providing & fixing retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on mild steel angle iron post 75mm x 75mm 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450mm x 450mm x 600mm,600 mm below ground level as per drawings and technical specification Clause 801 ii) 600mm circular

Providing & fixing retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on mild steel angle iron post 75mm x 75mm 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450mm x 450mm x 600mm,600 mm below ground level as per drawings and technical specification Clause 801 iii) 600mm equilateral triangle

Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1

Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC : 8 fixing in position including painting and printing etc as per drawing and technical specification cl 1703 (iv) 200m stone pre cast

Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC : 8 fixing in position including painting and printing etc as per drawing and technical specification cl 1703 (v) Ordinary KM Stone (Pre cast)

Maintenance of WBM road including filling up of pot holes, ruts and rectifying corrugated surface, damaged edges and ravelling as per technical specification Clause 1906.

Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502 (Provided only on WBM surface).

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared dry and hungry bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.

20mm thick open graded premix carpet using Bituminous Binder mixing with processed waste plastic (as per IRC -SP-98-20130 by replacement of 8%bitumen binder weight providing and laying and rolling of 20mm thick open graded premix carpet it ( thickness not less than 20mm at any place) composed of 13.2mm graded aggregate size @ 0.18 cum per 10 sqm & 11.2mm graded aggregate size & 0.09 cum per 10 sqm using bituminous binder @ 13.432 kg per 10 sqm ( i.e 92 % of standard bitumen and 8% waste processed plastic by weight shall be used for coating aggregate after heating ) as per IRC : SP:98:2013 layinh to required line , grade and levelto serve as finished to required level and graded as per technical specification cl 508 to be followed by seal coat of either type A , type B or Type C as per technical specification , Bitumen VG 30.

SealCoat : Providing and laying sealcoat sealing the voids in a bituminous surface laid to the specified levels , grade and cross fall using Type A , Type B and Type C as per technical specification cl 510 , Case -III Type C (II) Bitumen (S-65).

Providing and laying interlocking concrete block pavement (M40) having thikness 80mm aws per technical specification clause 1504 complete including carriage

Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes and conforming to the MoSrt&H specifications

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 801. i) 800mm x 600mm rectangular

Providing & fixing retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on mild steel angle iron post 75mm x 75mm 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450mm x 450mm x 600mm,600 mm below ground level as per drawings and technical specification Clause 801 ii) 600mm circular

Providing & fixing retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on mild steel angle iron post 75mm x 75mm 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450mm x 450mm x 600mm,600 mm below ground level as per drawings and technical specification Clause 801 iii) 600mm equilateral triangle

Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1

Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC : 8 fixing in position including painting and printing etc as per drawing and technical specification cl 1703 (iv) 200m stone pre cast

Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC : 8 fixing in position including painting and printing etc as per drawing and technical specification cl 1703 (v) Ordinary KM Stone (Pre cast)

Maintenance of WBM road including filling up of pot holes, ruts and rectifying corrugated surface, damaged edges and ravelling as per technical specification Clause 1906.

Scarifying the existing bituminous road surface to a depth of 150 mm and disposal of scarified material with a lift upto 3 m and lead upto 1000 m as per Technical specification clause 301.4.

Providing and laying interlocking concrete block pavement (M40) having thickness 80mm as per technical specification clause 1504 complete including Edge restraints.

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 801. i) 800mm x 600mm rectangular

Providing & fixing retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on mild steel angle iron post 75mm x 75mm 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450mm x 450mm x 600mm,600 mm below ground level as per drawings and technical specification Clause 801 ii) 600mm circular

Providing & fixing retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on mild steel angle iron post 75mm x 75mm 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450mm x 450mm x 600mm,600 mm below ground level as per drawings and technical specification Clause 801 iii) 600mm equilateral triangle

Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1

Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC : 8 fixing in position including painting and printing etc as per drawing and technical specification cl 1703 (iv) 200m stone pre cast

Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC : 8 fixing in position including painting and printing etc as per drawing and technical specification cl 1703 (v) Ordinary KM Stone (Pre cast)

Maintenance of WBM road including filling up of pot holes, ruts and rectifying corrugated surface, damaged edges and ravelling as per technical specification Clause 1906.

Providing and laying interlocking concrete block pavement (M40) having thikness 80mm aws per technical specification clause 1504 complete including carriage

Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502 (Provided only on WBM surface).

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared dry and hungry bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.

20mm thick open graded premix carpet using Bituminous Binder mixing with processed waste plastic (as per IRC -SP-98-20130 by replacement of 8%bitumen binder weight providing and laying and rolling of 20mm thick open graded premix carpet it ( thickness not less than 20mm at any place) composed of 13.2mm graded aggregate size @ 0.18 cum per 10 sqm & 11.2mm graded aggregate size & 0.09 cum per 10 sqm using bituminous binder @ 13.432 kg per 10 sqm ( i.e 92 % of standard bitumen and 8% waste processed plastic by weight shall be used for coating aggregate after heating ) as per IRC : SP:98:2013 layinh to required line , grade and levelto serve as finished to required level and graded as per technical specification cl 508 to be followed by seal coat of either type A , type B or Type C as per technical specification , Bitumen VG 30.

SealCoat : Providing and laying sealcoat sealing the voids in a bituminous surface laid to the specified levels , grade and cross fall using Type A , Type B and Type C as per technical specification cl 510 , Case -III Type C (II) Bitumen (S-65).

Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes and conforming to the MoSrt&H specifications

Maintenance of Hume Pipe Culvert (1 No) Brik masonry work in cement mortar in foundation of wall complete excl. pointing and plastering as per drawing and technical specification clause 1100(in prop. 1:4)

Plastering with cement mortar(1:6) 15mm thick on brick work for substructure as per technical specification

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 801. i) 800mm x 600mm rectangular

Providing & fixing retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on mild steel angle iron post 75mm x 75mm 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450mm x 450mm x 600mm,600 mm below ground level as per drawings and technical specification Clause 801 ii) 600mm circular

Providing & fixing retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on mild steel angle iron post 75mm x 75mm 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450mm x 450mm x 600mm,600 mm below ground level as per drawings and technical specification Clause 801 iii) 600mm equilateral triangle

Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1

Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC : 8 fixing in position including painting and printing etc as per drawing and technical specification cl 1703 (iv) 200m stone pre cast

Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC : 8 fixing in position including painting and printing etc as per drawing and technical specification cl 1703 (v) Ordinary KM Stone (Pre cast)

Maintenance of WBM road including filling up of pot holes, ruts and rectifying corrugated surface, damaged edges and ravelling as per technical specification Clause 1906.

Providing and laying interlocking concrete block pavement (M40) having thikness 80mm aws per technical specification clause 1504 complete including carriage

Plain/reinforced Cement concrete in Sub structure complete as per drawings and technical specification clauses 802,804,805 ,806 ,807,1202 and 1204 A .With Crushed Stone iv) RCC Grade M25 i) For height up to 5m For damaged Edge restrain

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 1000 m as per Technical Specification Clause 303.1. (i) Private Land

Single bamboo palasiding /walling of whole 2nd class bamboo (Jati or Bethua ) 75mm dia and closely packed & driven including fitting fixing with half bamboo kamis horizontally in three rows with cane or tying with wire complete and struts 1.50m apart longitudinally and providing brush wood as per drawing and technical specifications clause 1302.5 Driven at least 900mm below ground and 900 mm above ground , River side

Providing and dumping sand fill cement bags including filling with tied mouth with coir string and carriage to work site and duming at proper place and position as directed by deptt.

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 801. i) 800mm x 600mm rectangular

Providing & fixing retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on mild steel angle iron post 75mm x 75mm 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450mm x 450mm x 600mm,600 mm below ground level as per drawings and technical specification Clause 801 ii) 600mm circular

Providing & fixing retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on mild steel angle iron post 75mm x 75mm 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450mm x 450mm x 600mm,600 mm below ground level as per drawings and technical specification Clause 801 iii) 600mm equilateral triangle

Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1

Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC : 8 fixing in position including painting and printing etc as per drawing and technical specification cl 1703 (iv) 200m stone pre cast

Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC : 8 fixing in position including painting and printing etc as per drawing and technical specification cl 1703 (v) Ordinary KM Stone (Pre cast)