Construction of Balance Work of 2 Quarters for Judicial Officers at Shirur (K.) Tq. Shirur (K.) Dist. Beed

Dismantling brick masonry in lime or cement mortar and stacking the materils as directed with all leads, lifts etcetera

Excavation for foundation in Soft rock and old cement or lime masonry foundations including removing the excavated material upto a distance of 50 Metre beyond the building area and stacking as directed, including dewatering, preparing the bed for the foundation and necessary back filling with available earth /murum, ramming, watering including shoring and strutting etcetera complete (lift upto 1.50 metre) By Mechanical Means

Excavation for foundation in Hard rock by blasting including trimming and leveling the bed by chiseling where necessary and removing the excavated material and stacking it in measurable heaps within a distance of 50 Metre from the building area including dewatering and back filling with available earth/murum, watering, ramming, etcetera complete. (Lift upto 1.50 metre) By Mechanical Means

Providing preconstructional antitermite treatment as per Indian Standard 6313 (Part-II) by treating the top surface of plinth filling at the rate of 5 litres of emulsion concentrate at 1.0 percent of clorophyrifos per square metre of surface area covering ten years guarantee on bond paper.

Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 centi metre to 20 centi metre thick including hand packing and compacting etcetera complete.

Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, Steel centering, formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etcetera complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying in situ /Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for Reinforced Cement Concrete work in foundations like raft, strip foundations, grillage and footings of Reinforced Cement Concrete columns and steel stanchions etcetera including bailing out water, Steel centering formwork, laying/ pumping cover blocks, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etcetera complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etcetera complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for Reinforced Cement Concrete columns as per detailed designs and drawing or as directed including steel centering, formwork, cover blocks, laying/ pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etcetera complete,(Excluding reinforcement and structural steel) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etcetera complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for Reinforced Cement Concrete beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/ pumping, compactionand roughening the surface if special finish is to be provided and curing etcetera complete. (Excluding reinforcement and structural steel) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etcetera complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap/ granite / quartzite/ gneiss metal for Reinforced Cement Concrete slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/ pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etcetera complete,(Excluding reinforcement and structural steel) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etcetera complete. With fine aggregate (Crushed sand VSI Grade)

Providing and casting in situ / ready mix Plain Cement Concrete M-15 grade of trap metal for coping to head walls / parapet including centering, form work, compaction and curing etcetera complete. (with reversible drum type mixer/ concrete batch mix plant (pan mixer) with SCADA with fine aggregates of required specifications (Natural sand/ VSI sand finely washed etcetera )

Providing and fixing in position Thermo Mechanical Treated (TMT) - FE - 500 bar reinforcement of various diameters for Reinforced Cement Concrete pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etcetera as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.

Providing second class Burnt Brick masonry with conventional/ Indian Standard type bricks in cement mortar 1:6 in foundations and plinth of inner walls/ in plinth external walls including bailing out water manually, striking joints on unexposed faces, raking out joints on exposed faces and watering etcetera Complete.

Providing second class Burnt Brick masonry with conventional/ Indian Standard type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etcetera Complete

Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15 centi metre to 20 centi metre including watering and compaction etcetera complete.

Providing second class Burnt Brick masonry with conventional/ Indian Standard type bricks in cement mortar 1:4 in half brick thick wall including mild steel longitudinal reinforcement of 2 bars of 6 mili metre diametre / 2 hoop iron strips 25 mili metre x 1.6 mili metre placed at every third course, properly bent and bonded at ends scaffolding, racking out joints and watering etcetera complete.

Providing and fixing chicken mesh of 22 gauge, with about 30 centi metre width at the junction of Reinforced Cement Concrete members and brick work, of approved quality including fixing mesh in position by necessary drilling in concrete /Burnt Brick Masonry and or tying by binding wire etcetera complete.

Providing internal cement plaster 12 mili metre thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etcetera complete.

Providing fine cement finish 1.5 mili metre thick over green plaster surface including scaffolding curing etcetera complete.

Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mili metre thick in cement mortar 1:4 using waterproofing compound at 1 Kilogram per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mili metre thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etcetera complete.

Providing rough cast cement plaster externally in two coats to concrete, brick or stone masonry surfaces in all positions with base coat of 12 to 15 mili metre thick in Cement Mortor 1:4 and rough cast treatment 12 mili metre thick in proportion 1:1 1/2:3 including scaffolding and fourteen days curing complete.

Providing and erecting 1.5 metre high wire fencing with seven rows of barbed wire supported on Mild SteelAngles ( 50 mili metre x 50 mili metre x 6 mili metre) at 2.5 Mild Steel, Center to center including excavating pits for foundqtion, fixing post in cement cocnrete 1:4:8 of size 45 x 45 x 45 centi metre fastening the wire and painting the Mild SteelAngles with one coat of red lead primer and two coats of painting etcetera complete.

Providing and fixing mild steel grill work for windows, ventilators, etcetera 15 Kilogram/Square Metre as per drawing including fixtures necessary welding and painting with one coat of anticorrosive paint and two coats of oil painting complete.

Providing cement based water proofing treatment to terraces (Indian water proofing or alike) with brick bats laid in required slope to drain the water for any span after cleaning the base surface. Applying a coat of cement slurry admixed with approved water proofing compound and laying the brick bats on bottom layer in Cement Mortor1:5 admixed with approved water proofing compound filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with Cement Mortor1:3 admixed with approved water proofing compound and finally top finishing with average 20 mili metre. thick layers of same mortar added with jute fiber at 1 Kilogram per bag including finishing the surface smooth with cement slurry admixed with approved water proofing compound. Marking finished surface with false squares of 300 mili metre x 300 mili metre making the junctions at the parapet rounded and tapered top for required height, with drip mould at the junction of plaster and parapet and curing and covering 10 years Guarantee against leakproofness on Court fee stamp paper of Rs. 500/- including ponding test etcetera complete.

Providing and laying vitrified matt fininsh tiles having size 590 mili metre to 605 mili metre x to 605 mili metre of 8 to 10 mili metre thickness and confirming Indian Standard 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement morar including neat cement float, filling joints, curing and cleaning etcetera complete.

Providing and laying Antiskid Ceramic tiles of approved quality of size 30 centi metre x 30 centi metre and Confirming to Indian Standard 15622-2006 (Group-B IIA) for antiskid flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement s

lurry cleaning curing etcetera complete.

Providing and laying vitrified mirror / glossy finish tiles having size 590 mili metre to 605 mili metre x 590 mili metre to 605 mili metre of 8 to 10 mili metre thickness and confirming to Indian Standard 15622-2006 ( group Bla) of approved make, shade and pattern for dado & skirting in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearing etcetera complete.

Providing and laying telephone black / Amba White / Cadburybrown / Ruby red / Ocean Brown granite stone of 18 to 20 mili metre thick for door frame/ dado/ window boxing etcetera On Cement Mortor 1:6 including filling joints with polymer base filler nosing/moulding the sharp edges wherever necessary, curing, etcetera complete.

Providing and fixing machine cut machine polished 18 mili metre to 20 mili metre thick telephone black / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone for treads and risers of steps and staircases of approved colour and shade with full moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etcetera complete.

Providing 25 mili metre to 30 mili metre thick partition of polished black kadappa stone slab of approved quality including giving required size and shape etcetera Fixing in cement mortar 1:3 curing and cement etcetera complete. a) One side polish

Providing and preparing kitchen otta up to 75 centi metre width,made up from 30 mili metre thick and 75 centi metre high vertical support for kadppa at 1 metre centre to centre of 25 mili metre thick both side polished kadappa middle shelf and bottom of 20 mili metre thick one side polished kadappa with facia patti of 20 x 50 mili metre kadappa including all material labour cutting fixing with cement mortar and araldite curing polished and cleaning etcetera complete.

Providing and fixing heavy duty inter locking concrete Coloured paving blocks of 60 mili metre thickness of having a strength of 300 Kilogram/Square Centi Metre of approved quality and shape on a bed of crushed sand of 25 to 30 mili metre thick including skirting joints and cleaning etcetera complete

Providing and applying plaster with plaster of paris in 6 mili metre thickness to previously plaster surface in all position including preparing the surface scaffolding etcetera complete.

Providing and applying Two coats of wall care Putty on plastered surface and Ceiling and Walls to prepare surface even and smooth of approved make, etcetera complete.

Providing and applying pearl/ luster finish paint of approved colour and shade to the existing plaster surface including scaffolding, preparing the surface, applying the acrylic wall putti etcetera complete.

Providing and applying two coats of exterior weather shield paint of approved manufacture and of approved colour to the plastered surfaces including cleaning, preparing the plaster surface, applying primer coat, scaffolding if necessary, and watering the surface for two days etcetera complete.NOTE: For Item No. 15 to 18 prior approval of Superintending Engineer will be necessary

Providing and fixing in position (as per 1868 / 1982) Alluminium sliding window of three tracks with rectangular pipe 95 x 38.10 x 0.90 mili metre at weight 0.637 Kilogram/Running Metre with window frame bottom track section 92 x 31.75 x 1.30 mili metre at weight 1.070 Kilogram/Running metre Top and side track section 92 x 31.75 x 1.30 mili metre at weight 0.933 Kilogram/Running Metre The shutter should be of bearing bottom 40 x 18 x 1.25 mili metre at weight 0.417 Kilogram/Running Metre Inter locking section 40 x 18 x 1.10 mili metre at weight 0.469 Kilogram/Running Metre and handle and top section 40 x 18 x 1.25 mili metre at weight o.417 Kilogram/Running Metre As per detailed drawings and as directed by Engineer-in-charge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mili metre thick plain glass and aluminium mosquito net shutter with stainless steel jail with all required screws and nuts etcetera complete. With colour Anodising with box

Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 mili metre x 1.22 mili metre box type, 5 mili metre thick sheet glass louvers, of approved quality etcetera complete.

Providing and fixing Country cut teak wood double or single leaf second class fully panelled door shutter with 35 mili metre thick style and rail with 25 mili metre thick panels with openable fan light as per detailed drawings. Excluding the door frame 60 mili metre x 100 mili metre stainless steel fixtures and fastening and finishing the wood work with oil painting 3 coats. (Excluding the door frame)

Providing and fixing 34 mili metre thick moulded door shutter consisting of solid core single leaf flush door of 30 mili metre thickness lipped with 15 mili metre( 5 mili metre x 3) thick x 30 mili metre width on one style and top rail and 10 mili metre(5 mili metre x 2) thick x 30 mili metre width on other style and bottom rails. The inner panels laminated with 2 mili metre thick termite proof, water proof and fire resistant moulded Polyvenyle Chloride sheet with 2,4,6 design in different plain and /or prelim colours on one side after routing the moulded design on flush doors and 2 mili metreplain and /or pre lam Polyvenyle Chloride on other side using rubber adhesive on flush door and solvent cement adhesive on the Polyvenyle Chloride lipping etcetera as per direction of Engineer in charge and manufacturers specification and drawing etcetera complete.

Providing and fixing 900 mli metre high Stainless Steel 304 Grade Stainless steel railing with 40 mili metre diameter and 1.5 mili metre thick at top,40 mili metre diameter and 1.5 mili metre thick vertical supports spaced at 1.50 metre center to center and 8mm thick toughened glass including fabricating ,fixtures, errecting, necessary welding, grinding, finishing, buffing to stainless steel pipe etcetera complete

Providing and fixing collapsible steel gate in one / two leaves with hot rolled vertical channels of 18 x 9 x 3 mili metre minimum size, crossings of Mild Steel flats of size 18 x 5 mili Metre or E section for runner of minimum 40 x 6 mili metre size for flange, Mild Steel flat for top runner of minimum size 40 x 12 mili metre with roller wheels confirming to grade F.G. 150 fitted with snap headed rivets of minimum size 6 mili metre maximum spacing of vertical channels be 100 mili metre enclosed gate position and clear space of 150 mili metre between two sets of crossings with hold fasts, stoppers, spaces, handles, locking arrangement and one coat of red lead primer and oil painting etcetera complete. (Indian Standard 105211983).

Providing structural steel work in trusses, other similar trussed purlins and members with all bracing, gusset plates etcetera as per detailed designs and drawings or as directed including cutting, fabricating, hoisting, erecting fixing in position, Making riveted/ bolted/ welded connection and one coat of anticorrosive paint and over it 2 coats of oil painting approved quality and shade etcetera complete.

Providing and fixing corrugated galvanised iron sheets of 0.63 mili metre thick (24 British Wire Guage (B.W.G.)) for roofing without wind tiles including fastening with galvanised iron screws and bolts, lead and bitumen washers as per drawing etcetera complete.(Weight of 5.5 Kilogram/ Square Metre).

Providing and fixing European type white glazed earthenware water closet pan with Unplastisized Polyvenyle Chloride seat and lid with chromium plated brass hinges and rubber buffers including Unplastisized Polyvenyle Chloride and vent pipe up to the outside face of wall 10 litre enameled low level flushing cistern with fittings pipe stop tap brackets for fixing cistern 32 mili metre diametre Unplastisized Polyvenyle Chloride flush pipe wit

h fittings and clamps ,20 mili metre diametreUnplastisized Polyvenyle Chloride overflow pipe ,mosquito proof couplings Galvanised Iron chain and pulley,with water Jet and fitting including cutting and making good to the walls and floors testing etcetera complete.(prior approval of sample and brand by Executive Engineer is necessary before use)

Providing and fixing coloured glazed earthenware Wash Hand Basin of 63 centi metre x 45 centi metre size including cold water pillar tap/cold and hot water pillar tap brackets, rubber plugs and brass chain, stop tap and necessary pipe connection including Polyvenyle Chloride waste pipe and trap up to the outside face of the wall.

Providing and fixing white glazed earthenware sink 450 mili metre x 200 mili metre x 300 mili metre including all connection of the Galvanised Iron supply and lead waste pipes up to the outside face of the wall, cold water chromium plated screw down bib tap, rolled steel or C.I. brackets, rubber plug with chain and stop tap complete.

Providing and constructing Brick Masonry Inspection Chamber 60 centi metre x 45 centi metre x 90 centi metre including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W. pipes, Brick Masonry, plastering from inside and with frame fixed in cement concrete with Reinforced Cement Concrete Cover medium duty 140 Kilogram with frame etcetera complete.

Providing and constructing Brick Masonry Inspection Chamber 90 centi metre x 45 centi metre x 90 centi metre including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W.pipes, Brick Masonry, plastering from inside and with frame fixed in cement concrete with Reinforced Cement Concrete Cover medium duty 140 Kilogram with frame etcetera complete.

Providing and fixing H.D.P container Syntex or alike one piece moulded water tank made out of low density polythyler and built corrugation including of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow of all tanks capacity above 1000 to 20,000 litres

Providing and fixing chromium plated towel rod 16 mili metre diametre and 75 centi metre in length including all accessories complete.

Providing, laying and fixing Poly Venyle Chloride pipe of 75 mili metre diametre with fittings such as bends, tees, reducers, clamps, etcetera including necessary excavation, trench filling etcetera complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etcetera complete.

Providing and fixing Poly Venyle Chloride Rain water pipes of 110 mili metre outer diameter and having wall thickness of 2.2 to 2.7 mili metre confirming to Indian Standard 13592-1992 including proper rainwater receiving recess with Poly Venyle Chloride plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25 mili metre to 40 mili metre from face of wall a fixing with clips of approved quality and number ,filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on Cement Concrete or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the Poly Venyle Chloride fittings and additional 2 piece socket clips shall be got approved from engineer in charge etcetera complete.

Providing and fixing 100 mili metre diametre stabiliser pipe/ Poly Venyle Chloride soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etcetera complete.

Providing and fixing in position Unplastisized Polyvenyle Chloride ultra violet stabilized 110 mili metre outer diameter cowl dome confirming to Indian Standard-4985 including making joints with solvent cement etcetera complete

Providing and fixing 15 mili metre diametre screw down bib/ stop tap of brass including necessary socket union nut complete.

Providing and fixing 20 mili metre diametre screw down bib/ stop tap of brass including necessary socket union nut complete.

Providing and fixing 100 mili metre diametre chromium plated brass showers rose to 15 mili metre diametre supply pipe including necessary bend and socket complete.

Providing and fixing 10 centi metre Polyvenyle Chloride nahani trap with grating etcetera complete.

Providing soak pit of size 120 centi metre x 120 centi metre x 120 centi metre including excavating and filling with brick-bats.

Providing and fixing on walls/ ceiling/ floor 15 mili metre diametre CPolyvenyle Chloride pipe with necessary fittings, remaking good the demolished portion etcetera complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etcetera complete.

Providing and fixing on walls/ceiling/floor 20 mili metre diametre CPolyvenyle Chloride pipe with necessary fittings, remaking good the demolished portion etcetera complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etcetera complete.

Providing and fixing on walls/ ceiling/ floor 25 mili metre diametre CPolyvenyle Chloride pipe with necessary fittings, remaking good the demolished portion etcetera complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etcetera complete.

Providing and fixing reinforced cement concrete cover of size 90 centi metre x 45 centi metre with frame over inspection chamber etcetera complete. Heavy duty (225 Kilogram)

Providing and fixing reinforced cement concrete cover of size 60 centi metre x 45 centi metre with frame over inspection chamber etcetera complete. Heavy duty (160 Kilogram)

RWH - Shallow Percolation Pit providing, constructing 2.0m deep shallow depth percolation pit comprising of 1.0m dia pre-cast Reinforced Cement Concrete rings, 300 mili metre thick side filling around outside of Reinforced Cement Concrete rings (annular space) with 40 mili metre size boulders including filling of percolation pit up to 0.5m depth (from bottom up) with 25-75 mili metre clean washed gravels followed by 0.5m depth of 10-25 mili metre of clean washed stones followed by 0.5m of washed river fine aggregate (natural sand/crushed sand VSI grade finely washed etcetera) including netlon mesh between each gravel/fine aggregate (natural sand/crushed sand VSI grade finely washed etcetera) media layer including covering with Reinforced Cement Concrete slab, manhole frame & cover, Polyvenyle Chloride rungs etcetera including arrangement for inlet & outlet pipe, excavation & backfilling as shown in the drawing. The rate shall be inclusive of all labour, material, wastage, scaffolding, transportation, taxes, including all leads, lifts at all levels. All material should be of approved make. All works complete as per the drawing, technical specification and direction of the Engineer in charge

Executive's Table @ 1800Lx900Dx750HT Providing & Fixing of Table @ 1800Lx900Dx750HT - TOP & GABLE END to be made of Membrane finish with soft water fall edges & curved panel & Decorated Anodized section MODESTY PANEL to be made of 18 mili metre thick Prelaminated particle board with Polyvenyle Chloride edge band as per drawing

Pedestal Unit @ 420Lx450Dx650HT Providing & Fixing of PEDESTAL @ 420Lx450Dx650HT :- To be made out of Complete Membrane consist of three Drawers as per drawing.

Free Standing Table @ 1200Lx600Dx750HT Providing and fixing Table of Size 1200 x 600 x 750 mili metre Top: made from 25 mili metrePrelaminated Particle board. All edges are covered by 2 mm. Thk. Polyvenyle Chloride edge bands glued by hot melt glue applied by auto edge banding machine. Legs : C Shape made from CRCA Sheet with Powder Coat finish. Modesty panel : Made from 18mm both side prelaminated particle boards.All edges are covered by 0.8mm Polyvenyle Chloride edge bands glued by hot melt glue applied by auto edge banding machine.KEYBOARD TRAY ( WITHOUT MOUSE TRAY ) :- Metal Powder Coated - Black Color, CPU TROLLEY :- Metal Powder Coated - Black Color, 3 DRAWER PEDESTAL UNIT having

overall size 392L x 450D x 680Ht. mm. with central lock and key. Drawers and body are complete metal with powder coat finish, facia in 18 mili metreprelaminated particle board,

Book Case with Glass Shutter @ 825Lx300Dx1650HT Providing & Fixing of Book Case with Glass Shutter @ 825Lx300Dx1650HT:- To be made out of complete body & in 0.7mm thick CRCA & Shutter in 1.2 mili metre thick CRCA with glass pannel in Powder coating finish as per drawing.

Providing & Arrangemnt of High Back, Synchronized Mechanism with Multiple Locking, Adjustable Armrest, Gaslift for Seat height adjustment, Standard 5-prong P/Nylon Base with Leatherite Upholstery

Sofa Set 3+1+1 Providing & fixing Sofa Set 3+1+1 Brown and Cream leather DIMENSION Length: 182.5 (centi metres) Breadth (centi metres): 100 (centi metres) Height (centi metres): 100 (centi metres) Weight (Kilograms): 66 (Kilogram) Seating Capacity: Five Seat

Tea Table 900 mli metre X 750 mili metre X 450 mili metre for Mild Steel ante chamber Providing And Fixing Of Tea Table 900 mli metre X 750 mili metre X 450 mili metre With 12 mili metre Thick Colour Eitched Tempered Glass With Bevelled Drawing Made Out Of 18mm Thick Waterproofing Ply. The Outer Laces To Be Finished With High Quality 4 mili metre thick Veneer Or 1 mili metre thick Mica etcetera

Wardrobe with Mirror @ 900LX 600DX 1965H Providing and Fixing Wardrobe with Mirror of size 900LX 600DX 1965H The wardrobe side panels and doors are made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2 mili metre thick Polyvenyle Chloride edge Banding. The shelves are made of 18mm thick Prelam Particle Board with decorative laminate on both sides. The top is made of 36 mili metre prelam particle board with decorative laminate on both sides. (18mm Prelam Particle board and 18mm batons on all sides to achieve 36 mili metre overall thickness). The exposed edges of the top are sealed with 2 mili metre thick Polyvenyle Chloride edge Banding. The top most part of the wardrobe has an aluminum hanger rod of EBCO make. One drawer of size 400(W) x 150(H) x 450 (D) made of 18mm thick prelam Particle Board has been considered. The drawer will have a multipurpose lock of EBCO premium make. The wardrobe handles are Satin SS finish of 160 mili metre pitch. The wardrobe has a multipurpose lock of EBCO make. All hinges considered are Hettich make. Necessary good quality hardwares have been considered as required.

Single Bed @ 2025LX 1000DX 650H Providing and fixing Single Bed of Size 2025Lx1000Dx650H with matress and pillow. Understructure: - The legs are made of Square tube of size 25 x 25 mili metre made out of MS with a thickness of 1.2 mm. The legs should have corner brackets welded to it at two levels. The corner brackets are made of 2 mili metre thick CRCA having a L shaped structure to join the side panels and headboard to the leg. Three Numbers of Horizontal stiffeners are provided at equal intervals. The stiffeners are made of Square tube of size 25 x 25 mili metre made out of MS with a thickness of 1.2 mili metre The middle Horizontal Stiffener has a leg attached to it to transfer the load to the ground and add to the strength and stability of the complete structure. This leg is also made of Square tube of size 25 x 25 mili metre made out of MS with a thickness of 1.2 mili metre All Metal components to undergo 7 tank treatment process and should be powder coated to the thickness of minimum 50 Microns DFT. Side Panel: - The side panels are made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2 mili metre thick Polyvenyle Chloride edge Banding. The overall width of the side panel is 150 mili metre The side panels have 18mm thick prelam particle board Baton running for required length to add rigidity to the structure. Head Board :- The head board is made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2 mili metre thick Polyvenyle Chloride edge Banding. The head board size to be considered as 1000 x 650 mili metre Foot Board :- The foot board is made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2 mili metre thick Polyvenyle Chloride edge Banding. The head board size to be considered as 1000 x 450 mili metre Bed Base: - The Bed Base is made up of 12 mili metre thick Prelam Particle Board with both side White laminate.

Dressing Table @400LX 400DX 1800H Providing & Fixing Dressing Table of size 400LX 400DX 1800H.The Dressing table unit is made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2 mili metre thick Polyvenyle Chloride edge Banding. The unit has one drawer and one shelf. The dressing table has a mirror of 4 mili metre thick pasted on 18mm thick prelm particle board attached to the base unit. The mirror size considered is 1155 x 360 x 4(t). The mirror has been pasted using high quality 3M sticker.

Bed Side Table @ 400LX 400DX 415H Providing and Fixing Bed Side Table of size 400LX 400DX 415H The bed side unit is made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2 mili metre thick Polyvenyle Chloride edge Banding. The bed side table has one drawer and one shelf. The shelf is made of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2 mili metre thick Polyvenyle Chloride edge Banding

Kitchen Trolley Providing and Fixing stainless steel kitchen trolley of overall 26 " height and 22" depth,supported on aluminium pipes ,trolley basket made out of 5 mili Mild Steeltainless steel rod fitted on telescopic channel of size 1.5 " x 20 " x 22 " on both sides of trolley of 12 " or above size, panel having 40 Kilogram load bearing capacity of trolley made out of 20 mili metrePUC coated plywood and colour combination as directed by E-I-C.Inner side of panel covered by white mica ,100 mili Mild Steels. decorative handle.(The width and height of individual compartments shall be kept as directed by Engineer-in-charge)

Providing and Fixing Rollar Blinds AMI Make or approved make & shade of 38mm round Aluminium channel with Blackout fabric & telting with chain (Ball) system with all necessary fixtures and fitting etcetera complete. (Sample to be final by Engineer In-charge prior execution of work)

Providing Drilling 150 mm dia for Well

Providing Air Lifting Method at 90 Angle V Notch for Half Hour.

Providing P.V.C. Casing pipe 180 mm dia 6 Kg /Cm2 PVC Casing Pipe for 150 mm dia D.T.H. Borewell (IS 4985-1988)

Providing & Lowering Casing Pipe 150 mm dia DTH 180 mm dia 6 Kg /Cm2 PVC Casing Pipe (IS 4985-1988)

Providing & Fixing Cap for 180 mm dia PVC Pipe

GARDEN SOIL:-Supplying on site garden soil well sieved 80 % to pass through I.S. sieve of 10 mm size free from stones rubbish like dried grass roots and other such materials. The soil should be fresh from quarry. The color of the soil generally is red. The soil will be measured by measuring box. (Farma)

FARM YARD MANURE:-Supplying on site well decayed, well dried, well powdered, without clods and free from stones, dried grass and other rubbish material. The color of the manure generally is black. The manure will be measured by measuring box.(Farma)

Filling fresh garden soil / silt & manure in excavated area of depth 20cms.

Mixing garden soil/silt & manure thoroughly well, watering previous night. Planting required plant species; lawn grass as directed etc. complete for required depth 20 cms. for planting lawn/ shrub/ flower bed/ hedges/ edges/ canna bed/ ground cover. (1/10 of semiskilled labour)

Excavation for planting lawn/ shrub/ flower bed/ hedges/ edges/ canna bed in earth, soil of all types, soft murum, including removing the excavated material up to a distance of 50 mtrs. for a depth of 30 cms

5 (b) Flowering Trees Specification:- Minimum Girth 5 to 7 c.m. Minimum 5 to 6 Branches with Maximum number of Leaves , with clear tunk,healthy condition Free from pest and diseases,well seteled i

n appropriate size of Plybag,uniform in size and root system are undamaged.

i) Gulmohar

ii) Parijat

iii) Sita ashok

iv) Palas

6 (c) Foliage Trees Specification:- Minimum Girth 8 to 10 c.m. Minimum 5 to 6 Branches with Maximum number of Leaves ,clear trunk, well Developed Canopy,Healthy conditionFree from pest and diseases,well seteled in appropriate size of Plybag,uniform in size and root system are undamaged.

i) Deshi Badam

ii) KaduNeem

iii) Peepal

iv) Wad/banyan

Excavation pit size 0.60 x 0.60 x 0.60m for planting small & medium ornamental plants/ large flowering/ shady trees (plant height 1 to 2 mtr.)/ palm varieties upto height 1 to 2 mtrs. in earth, soil of all types, soft murum, including removing the excavated & unwanted material up to a required distance of 50 mtrs.

Filling fresh garden soil / silt & manure in excavated pit size area of 0.60 x 0.60 x 0.60m

Providing and casting in situ / ready mix Plain Cement Concrete M-20 grade of trap metal for coping to head walls / parapet including centering, form work, compaction and curing etcetera complete. (with reversible drum type mixer/ concrete batch mix plant (pan mixer) with SCADA with fine aggregates of required specifications (Natural sand/ VSI sand finely washed etcetera )

Providing and erecting Y type barbed wire fencing with seven rows of wire with 2.45 mili metre diametre Galvanised Iron pipe ( Rezan/ concentiDeleted ire 0.75 mili metre diametre ) with hot dip and Galvanised Iron coated hooks as per drawing supported on Mild Steel Angle 50 x 50 x 6 mili metre at 2.5 Metric Tonner. centre to centre including fixing and fastening with wire, painting Mild Steel Angles with one coat of red lead primer and two coat of oil paint etcetera complete.

Providing and fixing mild steel grill gate with angle iron frame 65 mili metre x 65 mili metre x 10 mili metre with iron bars at 150 mili metre centre to centre and diagonal flats as per the detailed drawing including hinges, pivot block locking arrangement, welding riveting and oil painting of three coats of approved shade Weight of gate 35 Kilogram/Squre metre.

Excavation for roadway in soft rock, including dressing section to the required grade, camber and side slopes and conveying the excavated materials with all lifts upto a lead of 50 metre and spreading or stacking as directed.

Providing, cutting, bending, hooking, tying and laying in position Thermo Mechanical Treated (TMT) FE 500 steel bars for reinforcement for all Reinforced Cement Concrete works as per detailed drawings etcetera complete.

Providing and laying in-situ M-30 Grade unreinforced plain cement concrete pavement over a prepared sub base with 43 grade cement, coarse and fine aggregate(VSI grade finely washed crushed sand) conforming to IS 383, using fine and coarse aggregates combined gradation as per Table 600-3 of MORTH Specification 2013, mixed in a batching and mixing plant/ non tilting mixer and Weigh batcher as per approved mix design, admixtures, transporting to site, spreading, laying with approved make paver, compacted and finished in a continuous operation, finishing to lines and grades as directed by Engineer-in-charge and curing by curing compound /by providing cement vata in cement Mortar 1:8 @0.6 metre X 0.6 metre centre to centre, admeasuring 80 mili metre at bottom and 40 mili metre at top with depth of 75 mili metre and maintaining the same throughout curing period by any other method approved by Engineer-in-charge.