COMPREHENSIVE MAINT OF WATER SUPPLY SYSTEM AT SI LINES UNDER GE BHOPAL

Amount

Note :(i) Please refer Sch A/ BOQ Notes before quoting the tender for all phases/ items mentioned below. (ii) Amount of Schedule of credit shall be deducted offline

Comprehensive maintenance of SCADA based water supply pumping and distribution system by employing one trained technician in each shift for 03 Shifts (each shift of 08 hrs, shift timings will be as directed by Engineer-in-charge) i.e. 03 technician per day, ITI qualified (trade as per requirement of Engineer-in-charge) with at least 01 (one) year experience in the relevant field OR matriculate with atleast 05 (five) years experience in the relevant field and requiste certificates in this regard including carrying out repairs, maintenance and servicing of all PLC panels and all connected circuit and accessories as required for all the modernised water supply system as described below at SI Line Bhopal under GE Bhopal as follows:- (a) Servicing and maintenace/repairs and replacement of defective components/spare parts of PLC based control panels including all accessories modem, antenna etc. installed at various pump houses, OHT and Master control station ,Mimic panel. (b) Repair/maintenance by disconnecting, cleaning, greasing for wear and tear complete servicing, refixing, lathing installing and commission of all motorised valves, Pressure switch, Ultrasonic level sensor. (Contd...)

Item No 1.10 contd.. The scope of work also covers:- (i) Any changes to the Programmable Logic Controller(PLC), e.g. Changes in ladder logic of programme, changes in operational timing, etc. (limited to the scope of items covered under this AMC) (ii) Any changes to the SCADA software, e.g. Changes in report format, changes in operational screens, creation of soft keys etc. (limited to the scope of items covered under this AMC) (iii) SCADA reports related to all the systems to be mailed to AGE/JE on every week (iv) To attend break down maintenance ( within 4 hours of reported time) and replacement of unservicable spare parts as required at site complete all as specified and directed by Engineer in charge Note (i) All components/spare parts replaced shall be measured and paid seperatly as supply only item mentioned in schedule ,fixing charges shall deemed to be include in this item. (2) All the calls related to unservicability/ break down of the system should be attend with in 4 hours, if failed so a penalty of Rs 1000/- can be imposed on each day untill the system gets repaired . (3) The quoted rate shall also inclusive of all the charges for the communications, i.e. 01 Nos bsnl broad band connection with static IP at Pump House and GPRS enabled data cards used in all PLC based panel related to this scope of work. (4) The quoted rate shall also inclusive Here in before and cleaning and maintain of surrounding of the installation building in such mainner of model installation and minor repair for leakage providing gland packing, replacement of flange gasket and maintenance of control panel /Pumping Set including replacement of rewireable fuses, piece of wire of any guage or size tightening loose connections etc. (with safty norms) of pump house.

Item No1.10 contd.. Note :- (a) The servicing of Motorised valve, PLC base control Panels, Mimic Panels shall be done by authorized representative of the Manufacturer or any other agency dealing with the installation and maintenance of SCADA system having vast experience in the relevant field only. The technician shall submit a letter from the Manufacturer or any other agency dealing with the installation and maintenance of SCADA system having vast experience in the relevant field as proof of his being a authorised representative of the Manufacturer or any other agency dealing with the installation and maintenance of SCADA system having vast experience in the relevant field. The technician shall also submit a signed report on original letter head of the manufacturer Manufacturer or any other agency dealing with the installation and maintenance of SCADA system having vast experience in the relevant field that servicing as been carried out by him. (b) Any changes to the Programmable Logic Controller (PLC), e.g. changes in ladder logic of programme, changes in operational timing, etc. (limited to the scope of work covered under this AMC) shall be carried out by authorized representative of the Manufacturer of PLC based Panels or any other agency dealing with the installation and maintenance of SCADA system having vast experience in the relevant field only. The programmer shall submit a letter from the manufacturer or any other agency dealing with the installation and maintenance of SCADA system having vast experience in the relevant field as proof of his being an authorized representative of the Manufacturer or any other agency dealing with the installation and maintenance of SCADA system having vast experience in the relevant field. The programmer shall also submit a signed report on original letter head of the Manufacturer or any other agency dealing with the installation and maintenance of SCADA system having vast experience in the relevant field that servicing as been carried out by him. (c) Any changes to the SCADA software, e.g. changes in report format, changes in operational screens, creation of soft keys etc. (limited to the scope of work covered under this AMC) shall be carried out by authorized Manufacturer of PLC based Panels or any other agency dealing with the installation and maintenance of SCADA system having vast experience in the relevant field only. The technician shall submit a letter from the Manufacturer or any other agency dealing with the installation and maintenance of SCADA system having vast experience in the relevant field as proof of his being a authorized representative of the Manufacturer or any other agency dealing with the installation and maintenance of SCADA system having vast experience in the relevant field. The technician shall also submit a signed report on original letterhead of the Manufacturer or any other agency dealing with the installation and maintenance of SCADA system having vast experience in the relevant field that servicing has been carried out by him. (d) Make of SCADA and License key installed at site : Rockwell, siemens,

Comprehensive maintenance, Upgradation and Repairing of Existing Scada also Programming and installation of SCADA software with with new additional features and upgradation of reporting software). Upgradation of existing CPU with scada compactible operating system, anti virus etc display of various technical parameters and fault display during auto operation in main receiving system New system which is compactible to run 24 X 7 basis, specification as follows PC -INTEL CORE I5 Processor,4GB RAM DDR3,500GB HDD,NOTE- SOFTWARE LISCENCE KEY WILL PROVIDED FOR THE PERIOD OF 5 YEARS Make: ( IBM/HP/COMPAQ/DELL) key board, mouse , 32 inch flat monitor.Make- Wincc v7.3 SIEMENS/ROCKWELL/GE FANUC /MITSUBHISI

Supply only single phase Preventor Model 1 :VSP D2 complete all as specified & directed. [Make - Minilec or equivalent as approved by GE]

Supply only Relay with base 4 C/O /24 V DC complete all as specified & directed. [Make LEONE/IDEC or equivalent as approved by GE]

Supply only Relay with base 4 C/O 240V AC complete all as specified & directed. [Make LEONE/IDEC or equivalent as approved by GE]

Supply only LED Indicator Colour/Red /yellow/Green/Blue complete all as specified & directed. [Make : ESBEE / TEKNIC/TELEMEACHNIQUE or equivalent as approved by GE]

Programmable logic controller(PLC) CPU model S7300 224XP CN 24 vdc/dc With 256 digital input/output & 64 analog output for scada operation and data transmition to modem.make:-SIEMENS/ALLEN BRADELY/GE FANUC/ABB/MITSUBHISI or equivlent as approved by GE

Supply only I/O module for Programmable Logic Controller complete all as specified & directed. [Make :Mitsubishi or equivalent as approved by GE]

Supply and installation of HMI (Human Machine Interface) for Programmable Logic Controller complete all as specified & directed. [Make :Mitsubishi /Renu or equivalent as approved by GE]

Supply only push button with LED Indicator - 240 V A.C. Colour Red /Green or equivalent as approved by GE. [Make : ESBEE / TEKNIC/TELEMEACHNIQUE or equivalent as approved by GE]

Supply only Buzzer - 240 V A.C complete all as specified & directed. [Make : C&S / MIMIC or equivalent as approved by GE]

Supply only of Flow switch complete all as specified & directed. [Make : Rapid controls / Donfoss / Indfoss or equivalent as approved by GE]

Supply only of Pressure switch complete all as specified & directed. [Make Indfoss/Danfoss or equivalent as approved by GE]

Supply only Electric motor suitable for Actuator following size complete all as specified and directed. [Make: sdtork/Ritetork, Rubix Automation Pvt Ltd, Unit No 5, Survey No-139, Near Malan Form Jeevan Nagar, Tathewade, Pune 411033, mail id: purchase [email protected]” or equivalent as approved by GE]

50/80 mm dia

100 mm dia

150 mm dia

Supply only Butterfly valve for the following size complete all as specified and directed. [Make: AUDCO/VIRGO/L&T/INTERVALVE or equivalent as approved by GE]

50 mm dia

80 mm dia

100 mm dia

150 mm dia

Supply only Capacitor for Actuator suitable for 50/80/100/150 mm dia Motorized Butterfly Valve complete all as specified & directed.

Supply only Resistor for Actuator suitable for 50/80/100/150 mm dia motorized Butterfly Valve complete all as specified & directed.

Supply only Limit switch for Actuator suitable for 50/80/100/150 mm dia motorized Butterfly Valve complete all as specified & directed.

Supply only PPI cable for communication with plc to modem for transmission digital parameters to RS232 to RS485 port, complete all as specified & directed. [Make: SIEMENS/ROCK WELL/GE FANUC/MITSUBHISI or equivalent as approved by GE]

Supply only Power Supply unit, 240V AC input, 24V DC output, (SMPS) for auxillary supply for various equipments, complete all as specified & directed. [Make: SIEMENS/MINILEC or equivalent as approved by GE]

Supply only GSM based Communication Modem for data transmission from various location to main receiving system, complete all as specified & directed. [Make: SIEMENS/ALLEN BRADELY/GE FANUC/ABB/MITSUBHISI or equivalent as approved by GE]

Supply only Communication cable for PLC to HMI (Human Machine Interface) for transmission digital parameters to RS485 to RS232 port, complete all as specified & directed. [Make: SIEMENS/ALLEN BRADELY/GE FANUC/ABB/MITSUBHISI or equivalent as approved by GE]

Supply only Ultrasonic Level Sensor range 0-5M complete all as specified & directed. [Make: Banner or equivalent as approved by GE]

GSM based Communication Modem for data transmission from various location to main receiving system. make SIEMENS/ALLEN BRADELY/GE FANUC/ABB/MITSUBHISI

Supply only 9DB Antenna GPRS Modem complete all as specified & directed.

Supply only UPS Battary complete all as specified & directed. [Make Exide or equivalent as approved by GE]

Supply only 2 KVA UPS complete all as specified & directed. [Make -Numeric or equivalent as approved by GE]

Supply only MCB 3P 6A complete all as specified & directed. [Make -LEGRAND or equivalent as approved by GE]

Supply only MCCB 160 Amp, complete all as specified & directed. [Make -LEGRAND or equivalent as approved by GE]

Deduct schedule of credit (calculation will be done off line) Rs. 17580.00

KPELECTRICAL AND AUTOMATION

AUTOMATION AND SWITCHGEAR CONTROL