SPECIAL REPAIR TO OR MD ACCN BLDG NO P 46 AT ADM AREA CPE ITARSI UNDER GE BHOPAL

Amount

Note :(i) Please refer Sch A/ BOQ Notes before quoting the tender for all phases/ items mentioned below. (ii) Amount of Schedule of credit shall be deducted offline

Demolition of Cement concrete (unreinforced) in ground floor and pavings not exc 15 cm thickness (below or above ground level) including surface finishes of any type ie tiles, kota stone complete all as specified and directed

Excavating over areas, under floor n exc 1.5m deep and getting out any type of soil below floor complete all as specified and directed.

Removing excavated soil n exc 50m and depositing where directed at a level not exc 1.5m above the starting point complete all as specified and directed.

M&L for Moorum and sand filling under floors or pavings laid in layers n exc 15 cm thick spread, levelled and rammed including watering (Sand and moorum will be mixed in ratio 1:1) complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub base complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) as in sub floor finished even and rough for receiving further floor finishes.ie tile etc complete all as specified and directed.

M&L for 50 mm thick PCC (1:3:6) type C1 (using 20mm graded stone aggregate) as plinth protection laid in a slope 1:50 and PCC shall be laid in alternative bays (bay length shall be not exceeding 2.0 m each) and finished fair on top without using extra cement. Joints shall be filled with bitumastic gola with 80/25 bitumen (1 part bitumen mixed with 3 part of sand) complete all as spciified and directed.

M&L for Hardcore of broken stone or boulders gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for anti termite treatment treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area, complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from frames) not exc 1.5 Sqm each and making good of disturbed surface to match the existing surface complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from frames) exc 1.5 Sgm but not exc 4 Sqm each and making good of disturbed surface to match the existing surface complete all as specified and directed.

S&F 125x60mm size pressed steel frame for door with one or more rebates including necessary fixing lugs, lock striking plates, hinges, hold fast etc. complete size /profile of frame as per IS including one shop coat of primer complete all as specified and directed.

S&F 105x60mm size of pressed steel frame for door with one or more rebates including necessary fixing lugs, lock striking plates, hinges, hold fast etc. complete size /profile of frame as per IS including one shop coat of primer complete all as specified and directed.

M&L plain cement concrete 1:3:6 type C1 using 20 mm graded stone aggregate as in copings, hold fast, back filling of pressed steel frame and other similar work water troughs and the like including weathering, slightly rounded or chamfered angles and throating etc including form work, complete all as spcefied and directed.

Taking down cement plaster on brick walls etc including surface finishes such as tiles, mosaic etc raking out joints, hacking for key scrubing down with water etc, complete all as spcefied and directed.

M&L for cutting "V" section to cracks in existing roof or terracing/ brick wall including cleaning, and grouting with cement sand slurry 1:3, complete all as spcefied and directed.

S&F wire netting as chicken wire mesh of galvanised mild steel wire 0.71 mm dia and size of mesh 25 mm for cracks fixed with nails etc complete all as spcefied and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet, 0.5mm thickness, of colour as approved by GE, having tensile strength of 550 Mpa as in roof coverings/cladding to wall, etc, fixed with & including self tapping screws on angle frame, complete all as specified and directed.

S&F framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc., n exc 10 kg each brackets, conforming to Fe-290 Gde E-165, complete all as specified and directed.

M&L for 15 mm thick cement plaster as in cement mortar 1:6 on brick or concrete internal wall surface other than fair faces surface even and fair complete all as specified and directed.

M&L for 15 mm thick cement plaster externally as in cement mortar 1:4 and mixed with WPC as per manufacturer instructions with cement and finished fair and even, complete all as specified and directed. (Note :- WPC shall be measured & paid separately)

Supply only water proofing compound, complete all as specified and directed.

Demolition of reinforced cement concrete in floors, beams, chajjas, landing slab in any position or height and similar suspended works, complete all as specified and directed.

M&L for cement concrete 1:4:8 using 40 mm graded stone aggregate as in foundation filling and mass concrete, complete all as specified and directed.

Use & waste of Form work to sides of concrete foundations, footings, bases of columns, sides & soffits of foundation and plinth beams and similar work for fair finished flat surfaces of concrete complete all as specified and directed.

M&L for reinforced cement concrete M25 grade design mix as in foundations, including rafts footings, foundatin beams, including raft, footings, basement slab and mass concrete, complete all as specified and directed.

Use & waste of Form work to sides of square or rectangular columns, pillars, posts and struts for fair finished surfaces of concrete complete all as specified and directed

M&L for reinforced cement concrete M25 grade design mix as in Column complete all as specified and directed.

Use & waste of Form work to sides & soffits of lintels over 1.5m clear span, floor or roof beams, cantilevers, etc for fair finished flat surfaces of concrete complete all as specified and directed.

S&F Mild steel TMT bars 10mm dia and over as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

S&F Mild steel TMT bars 6 to 8mm dia as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for reinforced cement concrete M 25 design mix Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for 10 mm thick plastering on concrete surface in cm 1:3 as in ceiling finishing the surfaces fair & even without using extra cement, complete all as specified and directed.

M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash, complete all as specified and directed.

Preparation of old decorated surfaces of ceiling including brooming, scraping down smoke spot, moulds, moss, efflorescent salts, trading oil, greasy spots and stopping nails marks and applying one coat of white wash on ceiling, complete all as specified and directed.

Preparing new plastered or unplastered surfaces of wall and M&L for applying two coats of distemper oil emulsion, white or tinted over a coat of primer on plastered surfaces complete all as specified and directed.

Complete removal of existing treatment on walls (any number of layers) by scrapping with steel scrappers or any other means, and applying two coats of oil emulsion distemper, white or tinted over one coat of white cement based putty (where required) all as specified and directed.Note - (i) Cement Putty shall be measured and paid separetely.(ii) Complete removal of existing surface to be carried out using mechanical scrappers and wiped clean with cotton cloth so that no dust/loose particles remain on the surface complete as directed by Engineer-in-charge.(iii) Hairline cracks upto 3 mm thickness shall be filled with crack seal of M/s Asian Paint or equivalent as approved; quoted rate is deemed to include for this aspect.

M&L for preparing new plastered or unplastered surfaces of walls and applying two coats of cement paint white or tinted, complete all as specified and directed.

M&L for two coats of cement base paint on old plastered external surface including complete removal of existing tratment washing down and rubbing and prepration of surface, complete all as specified and directed.

S&F factory made Flush shutters 30mm thick, solid core construction, with block board core and plywood face panels, both face covered with decorative face veneers with lipping/frame to match complete all as specified and directed.

M&L for factory made second class hardwood glazed and skeleton door shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc complete all as specified and directed.

S&F Factory made solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail panel will be of stainless steel wire gauze which shall be wrapped on an additional 8 mm square M.S. Solid tube and this tube shall be welded to 19mm x 19mm M.S. tubes. The G.I. wire gauge shall be stretched to tighten firmly complete all as specified and directed.

S&F 100mm size MS butt hinges medium weight cold rolled complete all as specified and directed.

S&F 150mm long aluminium handles cast type, anodised, complete all as specified and directed.

S&F 200mm long aluminium anodised barrel tower bolts of extruded section and fixed as specified.

S&F Aluminium alloy, anodised, sliding door bolt with hasp 250mm, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed staple plate and fixed complete all as specified and directed.

S&F 300mm long mild steel ordinary rat tail rod pattern springs including roller & roller plate complete all as specified and directed

S&F Second class hard wood small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like including all necessary labours articles n.exc 200 Cu.cm each, complete all as specified and directed.

S&F window ECO 4000 of double rebate openable /fixed windows made of galvanised steel colour coated /powder coated (base steel as per IS 513 of 'D' quality galvanised as per IS 277 with zinc of 120 grams /sqm) with total thickness of coating 0.58 microns, primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alyd backer 5-7 microns thick or powder coated with pure polyester powder up to 50-60 microns thick outer frame section 72 x 55mm, centre mullion section 72 x50 mm, shutter section 47 x20 mm, fly mesh section 40 x 20 mm and the fixed glass beading section 12 x12 mm, outer frame and mullion shall consists rebate for glazed shutter, fly mesh and 20 mm provision for guard bars /grills, the sections cut to length mitre joined with corner bracket, centre mullions cap, stay, handles, latch, 2 Nos tower bolts, 2 Nos of heavy duty stainless steel pivot hinges per shutter and penelled with 5mm thick plain float glass and SS mesh for fly mesh shutter (304 grade), fitted using EPDM (Ethyl Propylene Diamine Monomer) gaskets including fixing windows in the concrete/masonry wall by means of self expanding screws, including 10mm square bars welded to 6x12mm flat at a distance 150mm C/C (pitch) etc. complete all as specified and directed. Make : NCL Allek Seccolor Ltd (Model :ECO 4000) or equivalent as approved by GE)

S&F 3.00 mm thick sheet glass ordinary quality and glazing with oil putty in squares not exc 0.5 sqm in each pane complete all as specified and directed.

S&F 3.00 mm thick frosted sheet glass ordinary quality and glazing with oil putty in squares not exc 0.5 sqm in each pane complete all as specified and directed.

M&L for galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.00mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

S&F in repairs prelaminated particle board 18/19 mm thick, interior grade, prelaminated on one side with decorative choice lamination fixed with screws to timber frame work complete all as specified and directed.

M&L pressed steel frames for cup board chokhat of size 60x40mm with one or more rebates incl necessary fixing lug, hold fasts etc and one coat of redoxide primer, complete all as specified and directed.

M&L for prepration of new wooden surfaces and applying two coats of synthetic enamel paint over a coat of pink primer of any description over 10cm width or girth, complete all as specified and directed.

M&L for prepration of preprimed steel surfaces of any description over 10 cm in width or girth not other wise described and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for Non skid ceramic coloured tiles 7mm to 8mm thick (square/rectangular), area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors, etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with & including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L for Non skid ceramic coloured tiles 7mm to 8mm thick (square/rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors, etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with & including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L for Glazed ceramic coloured tiles 350mm x 250mm x 7mm thick or 450mm x 350mm x 7mm thick, in vertical surfaces such as skirting, dados and risers to steps, etc set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with & including 10mm thick rendering in CM 1:3 complete all as specified and directed.

M&L for 20-25 mm thick cuddapa prepolished stone over and including 10 mm thick cement mortar (1:4) bedding laid & jointed with slurry cement mixed with pigment to match the shade of the slab including rubbing and polishing, rounding to edge of stone slab one edge, such as steps, cooking plateorm and similar situtions complete all as specified and directed. (Note : Hole in stone slab for accomodate the gas pipe where required complete.)

Dismantling PVC water tanks and removing, of capacity exceeding 250 litres & not exceeding 500 litres etc, complete all as specified and directed.

S&F Rotational moulded (three layered, ISI marked) polyethylene water storage tanks (cylindrical vertical with closed top) of 500 litres capacity including PVC cover, hoisted and fixed in position including connecting up pipes complete all as specified and directed.

S&F in repairs Ball brass valves, ISI marked, high pressure, with polythene float and fly nut, screwed for iron pipe or brass ferrule 20 mm bore complete all as specified and directed.

S&F in repair Gun metal, globe or gate valves for 15 mm dia bore pipe with iron wheel head, screwed both ends for iron pipe and fixed in repair etc, complete all as specified and directed.

S&F 20 mm nipple suitable for HDPE water tanks including necessary driling holes etc, complete all as specified and directed.

S&F Sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including supply & fixing cantilever brackets of mild steel angle 35 x 35 x 5 mm and connecting union to pipe overall size:- 430mm x 510mm x 203mm, bowl size:- 430mm x 380mm x 203mm, including CP waste coupling and 32mm dia PVC waste pipe of suitable length complete all as specified and directed.. [MAKE:- Prayag (Cat No.1218D Gloss) or equivalent in Blue star/ Nirali/ make as per Appx 'C' (list of make) as approved by GE]

S&F in repair Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe 15mm bore complete all as specified and directed.

Taking up or down steel tubing and connections 15 mm bore, including cleaning (tubings only and not connections) for refixing or removal to store, complete all as specified and directed.

Taking up or down steel tubing and connections 20 mm bore, including cleaning (tubings only and not connections) for refixing or removal to store, complete all as specified and directed.

Cutting chases pining in brick, concrete walls built in cement mortar or cement lime mortar making good to facings where required and pointing in cement mortor 1:3 to ends or edges of shelves lintels etc and cutting chases for concealed water tubing cutting exc 10 cm but not exc 20 cm girth, complete all as specified and directed.

S&F Steel water tubes, medium grade, ISI marked, galvanised, 15 mm bore with all fittings, fixed to walls and ceiling or laid in floors complete all as specified and directed.

S&F Steel water tubes, medium grade, ISI marked, galvanised, 20 mm bore with all fittings, fixed to walls and ceiling or laid in floors complete all as specified and directed.

Refixing old GI pipe 15 mm bore & connections in new or old position to walls and ceiling or laid in floor all as specified & directed.

Refixing old GI pipe 20 mm bore & connections in new or old position to walls and ceiling or laid in floor all as specified & directed.

S&F in repairs Bib taps cast copper alloy chromium plated with crutch or butterfly handle, fancy type, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified and directed.

S&F in repair 15mm bore angle valve /stop valve chromium plated fency type cast copper alloy screwed down high pressure, crutch or butterfly handle, screwed both end for pipe or for unions complete all as specified and directed.

S&F in repair stop valves, 15mm dia, cast copper alloy, CP fancy type with long shank and cup (concealed type) screwd down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or for unions and fixed in pipe complete all as specified and directed.

S&F in repair PVC low level 10 litre capacity valveless syphonic action type white flushing cistern with inlet ball valve float and handle including brackets and necessary fittings etc complete all as specified and directed.

S&F in repair viteress china squtting pan "ORISSA PATTERN" size 580x440mm white with integral foot rest and flush pipe complete including provision of concrete bedding 1:2:4 type B0 complete all as specified and directed.

S&F in repair WHB white size 550x400mm vitreous china (flat back or angle back type) any size, including cutting for and pinning end of bracket or eracting stand but exclusive of fixing of supply and waste pipe complete all as specified and directed.

S&F in repairs tubular towel rail of brass, chromium plated glossy finish, 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

S&F PVC connection 15mm bore size with PTMT nuts of length 450mm long, complete all as specified and directed.

S&F 32mm dia PVC pipe low density (LDPE) of pressure 6kg/CM2 fixed to wall or laid in floor as waste pipe, complete all as specified and directed.

S&F swivel shower of PTMT any colour for fixing with 15mm pipe (Minmum weight 40gms), Complete all as specified and directed.

Demolition and breaking up or down PVC /AC/CI /Cement rain pipe fixed in any position internal dia of pipe 75/100mm, complete all as specified and directed.

S&F PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches, floors or fixed to walls, 110 mm bore complete all as specified and directed.

S&F PVC (SWR) bends 110 mm dia complete all as specified and directed.

S&F PVC (SWR) 110mm dia junction single equal or unequal with access door complete all as specified and directed.

S&F PVC (SWR) vent cowl 110 mm dia complete all as specified and directed.

S&F PVC (SWR) branch pieces 110mm dia complete all as specified and directed.

S&F PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches, floors or fixed to walls, 75 mm bore complete all as specified and directed.

S&F PVC (SWR) junction single (single T) 75 mm equal or unequal complete all as specified and directed.

S&F PVC (SWR) bends 75 mm dia provided with access door complete all as specified and directed.

S&F 75 mm out let PVC (SWR) floor trap with chromium plated grating including Jointing to waste pipe and fixed in cement concrete B1 (1:2:4 ) using 20 mm graded stone aggregate, complete all as specified and directed.

S&F 75 mm PVC (SWR) multi floor trap with grating including Jointing to waste pipe and fixed in cement concrete B1 (1:2:4 ) using 20 mm graded stone aggregate, complete all as specified and directed.

M&L for cleaning surface of sunken portion wall/bottom including taking out concrete and refil the same and applying cement slurry @1.2 Kg per Sqm and applying 15 mm thick cement plastred in CM 1:3 finished even and fair using extra cement and applying two coat of acrylic polymer modified cementious slurry as per manufactureas instruction to make the surface leak proof, complete all as specified and directed.

S&F in repairs Curtain rails 20mm dia, mild steel, chromium plated with fixing brackets, stops, rollers and finnels etc. and with all necessary fittings complete all as specified and directed.

Demolition brick work or stone / boulder masonry built in cement mortar as in wall etc complete all as specified and directed.

M&L for Brick work with Sub class 'B' bricks (Modular size), straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including necessary forms mould mitred /stopped ends etc, complete all as specified and directed.

M&L PCC 1:3:6 type C2 in surface channel or drains including necessary form works, stops, moulds etc, complete all as specified and directed.

M&L for heavy duty exterior grade tile texured finish of 300X300X10 mm thick mic/vitrified tile laid over and including 10 mm thick rendering in CM 1:4 as in steps complete all as specified and directed

Taking down carefully aluminium / copper point wiring with surface/ concealed PVC conduit or wooden batten ( light, fan, socket, bell or power ) including sunk in cast iron / pressed steel terminal boxes except fitting such as switches, ceiling roses, lamp holders, sockets, regulators, call bell, light fitting any sketch etc and making good disturbed surfaces of walls, floors etc complete all as specified and directed.

M&L for Point wiring with FRLS PVC insulated 1.5 sq mm multi stranded copper conductor cable 1100 volts grade drawn into and including concealed rigid non mettalic PVC conduit medium grade not less than 19/20 mm (ISI marked) with all fitting and fixing accessories including metal flush box and white sheet cover of any module as required at site etc and 1.5 sq mm multi stranded copper conductor cable as continuous earth wire drawn with wiring and connected to common earth dolly including make and matching the existing surface complete all as specified and directed for the following :-

One light point/fan point controlled by one switch

One light point controlled by two way switch

One socket outlet 5 Amps controlled by one switch on the same board.

One socket outlet 5 Amps controlled by one switch on independent board.

One bell / buzzer controlled by one bell push.

All as per item No. 106.00 above but with 2.5 sq mm multi stranded copper conductor cable for one 15 Amps socket outlet controlled by one switch on independent board and 1.5 sq mm PVC insulated multisranded copper conductor cable as continuous earth wire complete all as specified and directed.

S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB SP/DP 10A- 20 Amps with complete accessories complete all as specified and directed.

M&L for sub main wiring with two single core 4.0 sqmm multi stranded copper conductor, FRLS PVC insulated, unsheathed cable including rigid non metallic PVC conduit medium grade, ISI marked, 20 mm dia for sub main wiring including 4.0 sqmm FRLS PVC insulated and unsheathed stranded copper conductor as earth wire in conceled in wall of make & matching the existing surface make & matching the existing surface and making good to the disturbed surfaces to match the existing surfaces complete including taking down existing unserviceable submain of any size complete all as specified and directed. Note:- Two runs of 4.0 sqmm copper conductor cable, one run of 4 sqmm copper conductor and one run of PVC conduit will be measured as one unit.

S&F Ding Dong bell AC, 240 volts single pole complete all as specified and directed.

S&F ceiling rose surface bakelite two to three terminal complete all as specified and directed.

S&F Modular Bell push 6A 1 module complete all as specified and directed.

S&F Modular switch 1 way 6A, 240 volts 1 module complete all as specified and directed.

S&F Modular switch 2 way 6A, 240 volts 1 module complete all as specified and directed.

S&F Modular switch 1 way 16A, 240 volts 1 module complete all as specified and directed.

S&F Modular Socket, 6A - 2/3 pin combined 2 module complete all as specified and directed.

S&F Modular Socket 6A/16A - 2/3 pin combined 2 module complete all as specified and directed.

S&F Modular Fan step regulator, 120W, 240 volts 2 module complete all as specified and directed.

Supply and fixing Lamp holder, PVC/polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F 15 Watt LED bulb, in white colour with maximum Lumen output (850 lm) and colour temp 3000 K, complete all as specified and directed.

S&F LED lights fitting 1x20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F LED light fitting 1x7W/1X9W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Taking down Energy meter/Main Switches of any size after disconnecting supply and kept in safe custody, taking down & remove the old wooden meter box from site, plastering the existing disturbed wall surface including colour wash and refixing the Meter/Main Switches again on new MS Box (sintex box) of required size for complete for 01 TPN DB and four electric meter as per site with connection complete all as specified and directed.

Taking down MCB DBs including MCBs of all sizes after disconnecting supply complete all as specified and directed.

S&F sheet metal enclosure MCB DB 4 way tripple pole and neutral 415 volts factory made double door flush type complete all as specified and directed.

S&F sheet metal enclosures for SPN DB's 240 volts, factory made double door flush type, IP-42 protection and all as per IS-8623, made from sheet metal 8 way 200 Amps rated bus bar to be fixed with wall all accessories complete all as specified and directed.

S&F MCB single pole 240 volts 6 to 32 Amps complete all as specified and directed.

S&F MCB double pole 240 volts 16 to 40 Amps complete all as specified and directed.

S&F MCB TPN 63 Amp 415 Volts complete all as specified and directed.

Earthing complete with glavanised steel earth plate elactrode 600x600x6.0 mm thick buried directly in ground (Earth pit not less than 2.25 mtr deep below ground leves) with top edge of the plate not less 1.5 mtr deep below normal ground level connected to galvanised earth lead wire 4.0 mm dia by means of nut , bolt, check nut and washer of galvanised iron or of steel, earth lead protected by 15 mm dia GI pipe light grade watering pipe 20 mm dia GI light grade GI wire meshed funnel alternate layer of charcoal and salt PCC chamber, reassed for and including RCC cover including all necessary excavation and earth work, earth wire connected to main switch board, testing the earthing after completion all as specified and shown in electric plate No 3 complete all as specified and directed. Note:- (i) Item of earthing includes cost of excavation, removing, PCC Chamber, 15mm bore medium grade GI protection Pipe (7.5 Meters long) for earth lead . (ii) On testing after completion of earthing if the desired earth resistance is not obtained earthing will be re-done by the contractor at his own risk and cost to the entire satisfaction of Engr-in Charge.

S&F LED Bldg/street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection and GI pipe 40 mm dia, light grade for mounting bracket bent to shape 1.50 RM and fixing arrangement with two Nos of MS clamps set, nut bolts, washers of suitable size complete all as specified and directed.

M&L in replacement of 1100 volts grade heavy duty XLPE cable of size 25 Sqmm 3.5 core, passing through GI pipe with aluminium conductor stranded polyethylene insulated, conductor served with and including sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed complete including taking down existing unserviceable UG cable of any type and size complete all as specified and directed.

Excavation in trenches in any type of soil not exceeding 1.5 Mtr wide and not exceeding 1.5 Mtr in depth and getting out for foundation of pole, laying under ground cables etc and getting out omplete all as specified and directed.

M&L for sand filling with clean dry fine sand unwashed including gently punning around cables in trenches for cable protection (8 cm below cable & 15 cm above cable) complete all as specified and directed. [Note:-Compacted/punned thickness shall be measured & paid]

M&L Bricks laid in trenches flat with width equal to length of brick for cable protection well burnt sub class 'B' modular size laid across the cable complete all as specified and directed.

Returning filling in with the earth obtained from above item including spreading, levelling, watering and well ramming in layers and not exceeding 25 cm in layer complete all as specified and directed.

M&L for GI pipe light grade 50mm dia bore with all fittings and fixed complete to wall, to pole or laid in trenches and road crossing complete including taking down unserviceable GI pipe of any size complete all as specified and directed.

M&L for applying 1mm thick wall care putty, complete all as specified and directed.

Schedule of credit (calculation will be done off line) Rs. 58110.00

TANUJ CONST. CO.

M/s SHIVRATAN CONSTRUCTION

M/s Prayag Construction

AJIT ENTERPRISES

Dashmesh Enterprises