Construction of Bus Station at Baramati, Taluka Baramati, Dist Pune (Including Electrical Work)

Amount

CIVIL WORK Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 metre beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ra millimetre ing, watering including shoring and strutting etc. complete by Mechanical Means with all leads and lifts.

Excavation for foundation in hard murum including removing the excavated material upto distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ra millimetre ing, watering including shoring and strutting etc. complete by Mechanical Means with all leads and lifts.

Excavation for foundation in Soft rock and old cement or lime masonry foundations including removing the excavated material upto a distance of 50 metres beyond the building area and stacking as directed, including dewatering, preparing the bed for the foundation and necessary back filling with available earth /murum, ra millimetre ing, watering including shoring and strutting etc. complete by Mechanical Means with all leads and lifts.

Providing preconstructional antitermite treatment as per Indian Standard 6313 (Part-II) by treating the top surface of plinth filling at the rate of 5 litres of emulsion concentrate at 1.0 percent of clorophyrifos per square metre of surface area covering ten years guarantee on bond paper.

Filling in plinth and floors with approved excavated materials in 15 centimetre to 20 centimetre layers including watering and compaction complete.

Filling in plinth and floors with contractors soil. Sand or murum materials in 15 centimetre to 20 centimetre layers including watering and compaction complete.

Providing soling using 80 millimetre size trap metal in 15 centimetre . layer including filling voids with crushed sand /grit ra millimetre ing, watering complete.

Providing and laying Cast in situ/ Ready Mix cement concrete in Mix- 10 of trap metal for foundation and bedding including bailing out water, formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based Progra millimetre able Logic Controller with Supervisory Control and Data Acquisition enabled Concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural sand/ Crushed sand Vertical shaft impact (VSI) Grade finely washed etc.)

Providing and laying Cast in situ/ Ready Mix cement concrete in Mix-15 of trap metal for bed blocks, foundation blocks and such other items including bailing out water, plywood/ steel formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled Concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural sand/ Crushed sand Vertical shaft impact (VSI) Grade finely washed etc.)

Providing and laying in situ/ Ready Mix cement concrete Mix-30 of trap metal for reinforced cement concrete work in foundations like raft, strip foundations, grillage and footings of reinforced cement concrete columns and steel stanchions etc. including bailing out water, formwork, laying/ pumping cover blocks, compaction and curing roughening the surface if special finish is to be provided, (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled Concrete Batch Mix plant (Pan mixer) etc. complete, with fine aggregate (Natural Sand/ Crushed Sand Vertical shaft impact (VSI) Grade finely washed etc.)

Providing and laying cast in situ/ Ready Mix cement concrete Mix-30 of trap metal for reinforced cement concrete columns as per detailed designs and drawing or as directed including centering, formwork, cover blocks, laying/ pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete, (Excluding reinforcement and structural steel) with fully automatic micro processor based PLC with SCADA enabled Concrete Batch Mix plant (Pan mixer) etc. complete with fine aggregate (Natural Sand/ Crushed Sand Vertical shaft impact (VSI) Grade finely washed etc.) Ground Floor

Providing and laying cast in situ/ Ready Mix cement concrete Mix-30 of trap metal for reinforced cement concrete columns as per detailed designs and drawing or as directed including centering, formwork, cover blocks, laying/ pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete, (Excluding reinforcement and structural steel) with fully automatic micro processor based PLC with SCADA enabled Concrete Batch Mix plant (Pan mixer) etc. complete with fine aggregate (Natural Sand/ Crushed Sand Vertical shaft impact (VSI) Grade finely washed etc.) First Floor

Providing and laying cast in situ/ Ready Mix cement concrete Mix-30 of trap metal for reinforced cement concrete columns as per detailed designs and drawing or as directed including centering, formwork, cover blocks, laying/ pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete, (Excluding reinforcement and structural steel) with fully automatic micro processor based PLC with SCADA enabled Concrete Batch Mix plant (Pan mixer) etc. complete with fine aggregate (Natural Sand/ Crushed Sand Vertical shaft impact (VSI) Grade finely washed etc.) Second Floor

Providing and laying Cast in situ/ Ready Mix cement concrete Mix-30 of trap metal for reinforced cement concrete Beams and Lintels as per detailed designs and drawings or as directed including centering, formwork, cover blocks, laying/ pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel), with fully automatic micro processor based PLC with SCADA enabled Concrete Batch Mix plant (Pan mixer) etc. complete with fine aggregate (Natural Sand/ Crushed Sand Vertical shaft impact (VSI) Grade finely washed etc.) Ground Floor

Providing and laying Cast in situ/ Ready Mix cement concrete Mix-30 of trap metal for reinforced cement concrete Beams and Lintels as per detailed designs and drawings or as directed including centering, formwork, cover blocks, laying/ pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel), with fully automatic micro processor based PLC with SCADA enabled Concrete Batch Mix plant (Pan mixer) etc. complete with fine aggregate (Natural Sand/ Crushed Sand Vertical shaft impact (VSI) Grade finely washed etc.) First Floor

Providing and laying Cast in situ/ Ready Mix cement concrete Mix-30 of trap metal for reinforced cement concrete Slabs and Landings as per detailed designs and drawings including centering, formwork, cover blocks, laying/ pumping, compactionfinishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete, (Excluding reinforcement and structural steel) with fully automatic micro processor based PLC with SCADA enabled Concrete Batch Mix plant (Pan mixer) etc. complete, with fine aggregate (Natural Sand/ Crushed Sand Vertical shaft impact (VSI) Grade finely washed etc.) Ground Floor

Providing and laying Cast in situ/ Ready Mix cement concrete Mix-30 of trap metal for reinforced cement concrete Slabs and Landings as per detailed designs and drawings including centering, formwork, cover blocks, laying/ pumping, compactionfinishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete, (Excluding reinforcement and structural steel) with fully automatic micro processor based PLC with SCADA enabled Concrete Batch Mix plant (Pan mixer) etc. complete, with fine aggregate (Natural Sand/ Crushed Sand Vertical shaft impact (VSI) Grade finely washed etc.) First Floor

Providing and laying Cast in situ/ Ready Mix cement concrete in Mix-20 of trap/ granite/ quartzite/ gneiss metal for reinforced cement concrete Coping to plinth or parapet and sill of doors and windows moulded as per detailed drawings or chamfered as approved by the Engineer including centering, formwork, cover blocks, laying/ pumping, compacting , curing , finishing and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel), with fully automatic micro processor based PLC with SCADA enabled Concrete Batch Mix plant (Pan mixer) etc. complete, with fine aggregate (Natural Sand/ Crushed Sand Vertical shaft impact (VSI) Grade finely washed etc.) Ground Floor

Providing and laying Cast in situ/ Ready Mix cement concrete in Mix-20 of trap/ granite/ quartzite/ gneiss metal for reinforced cement concrete Coping to plinth or parapet and sill of doors and windows moulded as per detailed drawings or chamfered as approved by the Engineer including centering, formwork, cover blocks, laying/ pumping, compacting , curing , finishing and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel), with fully automatic micro processor based PLC with SCADA enabled Concrete Batch Mix plant (Pan mixer) etc. complete, with fine aggregate (Natural Sand/ Crushed Sand Vertical shaft impact (VSI) Grade finely washed etc.) First Floor

Providing and laying Cast in situ/ Ready Mix cement concrete in Mix-20 of trap/ granite/ quartzite/ gneiss metal for reinforced cement concrete Coping to plinth or parapet and sill of doors and windows moulded as per detailed drawings or chamfered as approved by the Engineer including centering, formwork, cover blocks, laying/ pumping, compacting , curing , finishing and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel), with fully automatic micro processor based PLC with SCADA enabled Concrete Batch Mix plant (Pan mixer) etc. complete, with fine aggregate (Natural Sand/ Crushed Sand Vertical shaft impact (VSI) Grade finely washed etc.) Second Floor

Providing and laying Cast in situ/ Ready Mix cement concrete in Mix-25 of trap metal for reinforced cement concrete Waist Slab, and steps of staircases as per detailed design and drawings or as directed including steel centering, plywood/ steel formwork, steel props, laying/ pumping, compaction, finishing uneven and honeycombed surface with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete, with fully automatic micro processor based PLC with SCADA enabled Concrete mixer/ concrete Batch Mix plant (Pan mixer) etc. complete, with fine aggregate (Natural Sand/ Crushed Sand Vertical shaft impact (VSI) Grade finely washed etc.) (Excluding einforcement, including cover block).(Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin). Ground Floor

Providing and laying Cast in situ/ Ready Mix cement concrete in Mix-25 of trap metal for reinforced cement concrete Pardi of required thickness including centering, formwork, cover blocks, laying/ pumping, compacting, curing, finishing and rougheningthem if special finish is to be provided and curing complete, (Excluding reinforcement and structural steel) with fully automatic micro processor based PLC with SCADA enabled Concrete Batch Mix plant (Pan mixer) etc. complete, with fine aggregate (Natural Sand/ Crushed Sand Vertical shaft impact (VSI) Grade finely washed etc.) Ground Floor

Providing and laying Cast in situ/ Ready Mix cement concrete in Mix-25 of trap metal for reinforced cement concrete Pardi of required thickness including centering, formwork, cover blocks, laying/ pumping, compacting, curing, finishing and rougheningthem if special finish is to be provided and curing complete, (Excluding reinforcement and structural steel) with fully automatic micro processor based PLC with SCADA enabled Concrete Batch Mix plant (Pan mixer) etc. complete, with fine aggregate (Natural Sand/ Crushed Sand Vertical shaft impact (VSI) Grade finely washed etc.) First Floor

Providing and laying Cast in situ/ Ready Mix cement concrete in Mix-25 of trap metal for reinforced cement concrete Pardi of required thickness including centering, formwork, cover blocks, laying/ pumping, compacting, curing, finishing and rougheningthem if special finish is to be provided and curing complete, (Excluding reinforcement and structural steel) with fully automatic micro processor based PLC with SCADA enabled Concrete Batch Mix plant (Pan mixer) etc. complete, with fine aggregate (Natural Sand/ Crushed Sand Vertical shaft impact (VSI) Grade finely washed etc.) Second Floor

Providing and fixing in position Thermo Mechanically Treated (TMT) FE -500 bar reinforcement of various diameters for reinforced cement concrete pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules, including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. Ground Floor

Providing and fixing in position Thermo Mechanically Treated (TMT) FE -500 bar reinforcement of various diameters for reinforced cement concrete pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules, including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. First Floor

Providing and fixing in position Thermo Mechanically Treated (TMT) FE -500 bar reinforcement of various diameters for reinforced cement concrete pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules, including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. Second Floor

Providing fly ash brick masonary with conventional /Indian Standardtype fly ash bricks in cement mortar 1:6 in foundation and plinth including bailing out water manually, striking joints, racking out joints, watering and scaffolding complete.

Providing Autoclaved Areated Concrete block masonary of Ecolite or equivalent make conforming to IS:2185(Part 3)- 1984 in extra fine jointing mortor of fixoblock of UltraTech or equivalent in superstructure including striking joints, racking out joints watering and scaffolding etc. complete. Ground Floor

Providing Autoclaved Areated Concrete block masonary of Ecolite or equivalent make conforming to IS:2185(Part 3)- 1984 in extra fine jointing mortor of fixoblock of UltraTech or equivalent in superstructure including striking joints, racking out joints watering and scaffolding etc. complete. First Floor

Providing Autoclaved Areated Concrete block masonary of Ecolite or equivalent make conforming to IS:2185(Part 3)- 1984 in extra fine jointing mortor of fixoblock of UltraTech or equivalent in superstructure including striking joints, racking out joints watering and scaffolding etc. complete. Second Floor

Providing Autoclaved Areated Concrete block masonary of Ecolite or equivalent make conforming to IS:2185(Part 3)- 1984 in extra fine jointing mortor of fixoblock of UltraTech or equivalent in Half brick thick wall including striking joints, racking out joints watering and scaffolding etc. complete. Ground Floor

Providing Autoclaved Areated Concrete block masonary of Ecolite or equivalent make conforming to IS:2185(Part 3)- 1984 in extra fine jointing mortor of fixoblock of UltraTech or equivalent in Half brick thick wall including striking joints, racking out joints watering and scaffolding etc. complete. First Floor

Providing Autoclaved Areated Concrete block masonary of Ecolite or equivalent make conforming to IS:2185(Part 3)- 1984 in extra fine jointing mortor of fixoblock of UltraTech or equivalent in Half brick thick wall including striking joints, racking out joints watering and scaffolding etc. complete. Second Floor

Providing and fixing chicken mesh of 22 gauge, with about 30 centimetre . width at the junction of reinforced cement concrete members and brick work, of approved quality including fixing mesh in position by necessary drilling in concrete/ B.B.masonry and or tying by binding wire etc. complete. Ground Floor

Providing and fixing chicken mesh of 22 gauge, with about 30 centimetre . width at the junction of reinforced cement concrete members and brick work, of approved quality including fixing mesh in position by necessary drilling in concrete/ B.B.masonry and or tying by binding wire etc. complete. First Floor

Providing and fixing chicken mesh of 22 gauge, with about 30 centimetre . width at the junction of reinforced cement concrete members and brick work, of approved quality including fixing mesh in position by necessary drilling in concrete/ B.B.masonry and or tying by binding wire etc. complete. Second Floor

Providing and applying gypsum plaster (with Gypsum material of Gypsum India/ Mega Sign or equivalent make) with finishing with gypsum material in 10 to 13 millimetre thickness to previously plastered surface/ or on newly brick surface (Excluding rough cast plaster) in all position including preparing and finishing the surface scaffolding etc. complete. Ground Floor

Providing and applying gypsum plaster (with Gypsum material of Gypsum India/ Mega Sign or equivalent make) with finishing with gypsum material in 10 to 13 millimetre thickness to previously plastered surface/ or on newly brick surface (Excluding rough cast plaster) in all position including preparing and finishing the surface scaffolding etc. complete. First Floor

Providing and applying gypsum plaster (with Gypsum material of Gypsum India/ Mega Sign or equivalent make) with finishing with gypsum material in 10 to 13 millimetre thickness to previously plastered surface/ or on newly brick surface (Excluding rough cast plaster) in all position including preparing and finishing the surface scaffolding etc. complete. Second Floor

Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 millimetre thick in cement mortar 1:4 using waterproofing compound at 1 kg per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 millimetre thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete. Ground Floor

Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 millimetre thick in cement mortar 1:4 using waterproofing compound at 1 kg per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 millimetre thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete. First Floor

Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 millimetre thick in cement mortar 1:4 using waterproofing compound at 1 kg per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 millimetre thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete. Second Floor

Providing and applying Texture plaster with finishing with texture material of approved make in 3 to 4 millimetre thickness on previously plastered surface, including Plaster Groove6 millimetre thickness or Tape Grooves 35 millimetre to 45 millimetre thickness or as required, in all positionincluding preparing the surface, scaffolding etc. complete. Ground Floor

Providing and applying Texture plaster with finishing with texture material of approved make in 3 to 4 millimetre thickness on previously plastered surface, including Plaster Groove6 millimetre thickness or Tape Grooves 35 millimetre to 45 millimetre thickness or as required, in all positionincluding preparing the surface, scaffolding etc. complete. First Floor

Providing and applying Royale Luxury Emulsion of Asian/ Berger/ Nerolac/ Dulux Paints or equivalent make on internal wall surface as detailed below Scrapping for surface with emery paper and wipe clean for area. Applying Asian/ Berger/ Nerolac/ Dulux Paints or equivalent wall primer with brush by adding mineral turpentine oil by 8 to 10 Percent or water by 15 to 20 Percent allowing to dry for 6 to 8 hoursAfter applying Asian/ Berger/ Nerolac/ Dulux Paints or equivalent acrylic wall putty with appropriate prpportion of water of allow to dry for period of 4 to 6 hours of activity. Scrapping with emery paper and wipe clean Applying paints Royale Luxury emulsion 1st coat with brush water content water 40 to 45 Percent or 65 to 70 Percent by role Applying paints Royale luxury emulsion 2nd coat with brush with water content 40 to 45 Percent or 65 to 70 Percent by roller. Ground Floor

Providing and applying Royale Luxury Emulsion of Asian/ Berger/ Nerolac/ Dulux Paints or equivalent make on internal wall surface as detailed below Scrapping for surface with emery paper and wipe clean for area. Applying Asian/ Berger/ Nerolac/ Dulux Paints or equivalent wall primer with brush by adding mineral turpentine oil by 8 to 10 Percent or water by 15 to 20 Percent allowing to dry for 6 to 8 hoursAfter applying Asian/ Berger/ Nerolac/ Dulux Paints or equivalent acrylic wall putty with appropriate prpportion of water of allow to dry for period of 4 to 6 hours of activity. Scrapping with emery paper and wipe clean Applying paints Royale Luxury emulsion 1st coat with brush water content water 40 to 45 Percent or 65 to 70 Percent by role Applying paints Royale luxury emulsion 2nd coat with brush with water content 40 to 45 Percent or 65 to 70 Percent by roller. First Floor

Providing and applying Royale Luxury Emulsion of Asian/ Berger/ Nerolac/ Dulux Paints or equivalent make on internal wall surface as detailed below Scrapping for surface with emery paper and wipe clean for area. Applying Asian/ Berger/ Nerolac/ Dulux Paints or equivalent wall primer with brush by adding mineral turpentine oil by 8 to 10 Percent or water by 15 to 20 Percent allowing to dry for 6 to 8 hoursAfter applying Asian/ Berger/ Nerolac/ Dulux Paints or equivalent acrylic wall putty with appropriate prpportion of water of allow to dry for period of 4 to 6 hours of activity. Scrapping with emery paper and wipe clean Applying paints Royale Luxury emulsion 1st coat with brush water content water 40 to 45 Percent or 65 to 70 Percent by role Applying paints Royale luxury emulsion 2nd coat with brush with water content 40 to 45 Percent or 65 to 70 Percent by roller. Second Floor

Providing and applying two coats of appex Ace white exterior paint of approved manufacture and of approved colour to the plastered surfaces including cleaning, prepairing the plaster surface, applying primer coat, scaffolding if necessary, and watering the surface for two days complete. Ground Floor

Providing and applying two coats of appex Ace white exterior paint of approved manufacture and of approved colour to the plastered surfaces including cleaning, prepairing the plaster surface, applying primer coat, scaffolding if necessary, and watering the surface for two days complete. First Floor

Providing and applying two coats of appex Ace white exterior paint of approved manufacture and of approved colour to the plastered surfaces including cleaning, prepairing the plaster surface, applying primer coat, scaffolding if necessary, and watering the surface for two days complete. Second Floor

Providing and laying in position flooring of telephone black / Amba White / Cat bary brown /Ruby red / Ocean Brown granite stone of approved shade and size 18 millimetre to 20 millimetre thick onbed 1:6 cement mortar including cement floats striking joints, pointing in cement mortar 1:3 curing andcleaning etc. complete. Ground Floor

Providing and laying in position flooring of telephone black / Amba White / Cat bary brown /Ruby red / Ocean Brown granite stone of approved shade and size 18 millimetre to 20 millimetre thick onbed 1:6 cement mortar including cement floats striking joints, pointing in cement mortar 1:3 curing andcleaning etc. complete. First Floor

Providing and laying in position flooring of telephone black / Amba White / Cat bary brown /Ruby red / Ocean Brown granite stone of approved shade and size 18 millimetre to 20 millimetre thick onbed 1:6 cement mortar including cement floats striking joints, pointing in cement mortar 1:3 curing andcleaning etc. complete. Second Floor

Providing leather finished polishing to Granite Stone slab by continuous grinding in 4 coats of different bits to receive rough and matt finish including buffing process before laying and fixing of stone as per drawing and design, including cleaning, washing and finishing etc. complete. Ground Floor

Providing leather finished polishing to Granite Stone slab by continuous grinding in 4 coats of different bits to receive rough and matt finish including buffing process before laying and fixing of stone as per drawing and design, including cleaning, washing and finishing etc. complete. First Floor

Providing and fixing machine cut machine polished 18 millimetre to 20 millimetre thick telephone black/ Amba White/ Cat bary brown/ Ruby Red/ Ocean Brown granite stone for treads and risers of steps and staircases of approved colour and shade with rounded moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete. Ground Floor

Providing and fixing machine cut machine polished 18 millimetre to 20 millimetre thick telephone black/ Amba White/ Cat bary brown/ Ruby Red/ Ocean Brown granite stone for treads and risers of steps and staircases of approved colour and shade with rounded moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete. First Floor

Providing and fixing machine cut machine polished 18 millimetre to 20 millimetre thick telephone black/ Amba White/ Cat bary brown/ Ruby Red/ Ocean Brown granite stone for treads and risers of steps and staircases of approved colour and shade with rounded moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete. Second Floor

Providing and laying ceramic tiles having size 30 centimetre . x 30 centimetre . conforming Indian Standard 15622/2006 (group D II-A) and 7 to 8 millimetre thick for flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with white/ colour cement slurry cleaning curing etc. complete. First Floor

Providing and Fixing in position, Carpet more than 800+ gsm, made with 100 Percent stain proof fibres of approved make along with 5 millimetre underlay as per Architectural and Acoustical Design and Instructions and Complete in all aspects including all materials labour,finishing etc. complete. First Floor

Providing and laying telephone black/ Amba White/ Cadburybrown/ Ruby red/ Ocean Brown granite stone of 18 to 20 millimetre thick for door frame/ dado/ window boxing etc. on Cement Mortar 1:6 including filling joints with polymer base filler nosing the sharp edges wherever necessary, curing, etc. complete. Ground Floor

Providing and laying telephone black/ Amba White/ Cadburybrown/ Ruby red/ Ocean Brown granite stone of 18 to 20 millimetre thick for door frame/ dado/ window boxing etc. on Cement Mortar 1:6 including filling joints with polymer base filler nosing the sharp edges wherever necessary, curing, etc. complete. First Floor

Providing and laying telephone black/ Amba White/ Cadburybrown/ Ruby red/ Ocean Brown granite stone of 18 to 20 millimetre thick for door frame/ dado/ window boxing etc. on Cement Mortar 1:6 including filling joints with polymer base filler nosing the sharp edges wherever necessary, curing, etc. complete. Second Floor

Providing and laying vitrified matt fininsh tiles for flooring having size 590 millimetre to 605 millimetre x to 605 millimetre of 8 to 10 millimetre thickness and confirming Indian Standard 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement morar including neat cement float, filling joints, curing and cleaning etc. complete. Ground Floor

Providing and laying vitrified matt fininsh tiles for flooring having size 590 millimetre to 605 millimetre x to 605 millimetre of 8 to 10 millimetre thickness and confirming Indian Standard 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement morar including neat cement float, filling joints, curing and cleaning etc. complete. First Floor

Providing and laying vitrified matt fininsh tiles for flooring having size 590 millimetre to 605 millimetre x to 605 millimetre of 8 to 10 millimetre thickness and confirming Indian Standard 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement morar including neat cement float, filling joints, curing and cleaning etc. complete. Second Floor

Providing and laying vitrified matt finish tiles for Skirting having size 590 millimetre to 605 millimetre x to 605 millimetre of 8 to 10 millimetre thickness and confirming Indian Standard 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc. complete. Ground Floor

Providing and laying vitrified matt finish tiles for Skirting having size 590 millimetre to 605 millimetre x to 605 millimetre of 8 to 10 millimetre thickness and confirming Indian Standard 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc. complete. First Floor

Providing and laying vitrified matt finish tiles for Skirting having size 590 millimetre to 605 millimetre x to 605 millimetre of 8 to 10 millimetre thickness and confirming Indian Standard 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc. complete. Second Floor

Providing and laying polished Kotah stone flooring 25 millimetre to 30 millimetre thick and of reqd. width in plain/ diamond pattern on a bed of 1:6 cement mortar including cement float,filling joints with neat cement slurry,curing,polishing and cleaning complete. Ground Floor

Providing and laying polished Kotah stone flooring 25 millimetre to 30 millimetre thick and of reqd. width in plain/ diamond pattern on a bed of 1:6 cement mortar including cement float,filling joints with neat cement slurry,curing,polishing and cleaning complete. First Floor

Providing and fixing in required position skirting or dado of polished Kotah Stone slab 25 millimetre to 30 millimetre thick fixed on base on plaster of cement mortar 1:4 including cement float, filling joints with cement slurry, curing rubbing, polishing and cleaning complete. Ground Floor

Providing and fixing in required position skirting or dado of polished Kotah Stone slab 25 millimetre to 30 millimetre thick fixed on base on plaster of cement mortar 1:4 including cement float, filling joints with cement slurry, curing rubbing, polishing and cleaning complete. First Floor

Providing and laying matt finish ceramic tiles of having size 30 centimetre x 30 centimetre confirming toIndian Standard 15622/2006 (group D II-A) and 7 to 8 millimetre thick for flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with white/colour cement slurrycleaning curing etc. complete. Ground Floor

Providing and laying matt finish ceramic tiles of having size 30 centimetre x 30 centimetre confirming toIndian Standard 15622/2006 (group D II-A) and 7 to 8 millimetre thick for flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with white/colour cement slurrycleaning curing etc. complete. First Floor

Providing and laying matt finish ceramic tiles of having size 30 centimetre x 30 centimetre confirming toIndian Standard 15622/2006 (group D II-A) and 7 to 8 millimetre thick for flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with white/colour cement slurrycleaning curing etc. complete. Second Floor

Providing and laying ceramic tiles having size 30 centimetre . x 60 centimetre . for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete. Ground Floor

Providing and laying ceramic tiles having size 30 centimetre . x 60 centimetre . for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete. First Floor

Providing and laying ceramic tiles having size 30 centimetre . x 60 centimetre . for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete.Second Floor

Providing and Laying factory made coloured chamfered edge Cement concrete grass paver blocks of required strength,thickness and size/shape, made by table vibratory method using PU mould, laid in required colour and pattern over 50 milimetre thick compacted bed of fine fine aggregate (natural sand/crushed sand VSI grade finely washed etc.), compacting and proper embedding/laying of inter locking paver blocks into the fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) and cutting of paver blocks as per required size and pattern, finishing and sweeping extra fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) and complete as per manufacturer spsecifications and direction of Engineer-in-Charge. 60 milimetre thick cement concrete paver block of Mix-35 grade concrete with approved colour and design and pattern. Ground Floor

Providing and fixing in position Gypsum board false ceiling with 12.5 milimetre thick Gypsum boards, screwed/ fixed to the under structure of suspended galvanised iron Grid constructed and suspended from the main ceiling consisting of ceiling sections of size 25 x 50 milimetre maximum center to center distance of 600 milimetre perimeter channel and intermediate channels at maximum center to center distance 1200 milimetre galvanized grid should be fixed to reinforced cement concrete slab. The gypsum board should be fixed to galvanized iron grid with necessary screws. The boards should be taped and filled from underside to give smooth, seamless ceiling. The rate should include necessary additional ceiling sections and intermediate channels. Additional intermediate channels should be fixed to strap hangers for additional support to prevent strapping at every 1200 milimetre item to be completed in all respect including necessary sleeves for ducts finishing of joints cut outs, painting including labour, material, lifts etc. all complete. Ground Floor

Providing and fixing in position Gypsum board false ceiling with 12.5 milimetre thick Gypsum boards, screwed/ fixed to the under structure of suspended galvanised iron Grid constructed and suspended from the main ceiling consisting of ceiling sections of size 25 x 50 milimetre maximum center to center distance of 600 milimetre perimeter channel and intermediate channels at maximum center to center distance 1200 milimetre galvanized grid should be fixed to reinforced cement concrete slab. The gypsum board should be fixed to galvanized iron grid with necessary screws. The boards should be taped and filled from underside to give smooth, seamless ceiling. The rate should include necessary additional ceiling sections and intermediate channels. Additional intermediate channels should be fixed to strap hangers for additional support to prevent strapping at every 1200 milimetre item to be completed in all respect including necessary sleeves for ducts finishing of joints cut outs, painting including labour, material, lifts etc. all complete.First Floor

Armstrong cellio open cell 150 millimetre cell size lay-in gi ceiling with armstrong suprafine 38 with 15 millimetre exposed grid system: Providing and fixing horizontal level Armstrong Cellio Open cell GI lay-in ceiling tiles with border panels forming board edge of size 600x600x38 millimetre (Nominal) having cell size of 150x150 millimetre made of 120 gsm galvanized steel as per IS 277 (2003) suitable for architectural finishes in 0.35 millimetre thickness as per in IS:513 (1994)in Global white color. The tile shall be electrostatically polyester powder coated using RoHS compliant powder having coating thickness ranging from 60-80 microns. The powder coating shall pass Salt Spray Test for 750 hours as per ASTM B117, QUV –A Test for 1000 hours as per ASTM G-154 – (Cycle – 1) and Humidity test for 1000 hours as per DIN 50017. The powder coating shall have an adhesion of GT0 as per EN ISO 2409. The shade variation across batches shall be delta E<1 using Excite/BYK Gardner instrument and gloss level of 25±5 Percent at 60˚ as per ASTM D523. Tile shall have a Fire Performance class A1 as per EN-13964.Properties of Tile Relevant Standards:Base Material 120 gsm galvanized steel Indian standard. Ground Floor

Armstrong cellio open cell 150 millimetre cell size lay-in gi ceiling with armstrong suprafine 38 with 15 millimetre exposed grid system: Providing and fixing horizontal level Armstrong Cellio Open cell GI lay-in ceiling tiles with border panels forming board edge of size 600x600x38 millimetre (Nominal) having cell size of 150x150 millimetre made of 120 gsm galvanized steel as per IS 277 (2003) suitable for architectural finishes in 0.35 millimetre thickness as per in IS:513 (1994)in Global white color. The tile shall be electrostatically polyester powder coated using RoHS compliant powder having coating thickness ranging from 60-80 microns. The powder coating shall pass Salt Spray Test for 750 hours as per ASTM B117, QUV –A Test for 1000 hours as per ASTM G-154 – (Cycle – 1) and Humidity test for 1000 hours as per DIN 50017. The powder coating shall have an adhesion of GT0 as per EN ISO 2409. The shade variation across batches shall be delta E<1 using Excite/BYK Gardner instrument and gloss level of 25±5 Percent at 60˚ as per ASTM D523. Tile shall have a Fire Performance class A1 as per EN-13964.Properties of Tile Relevant Standards:Base Material 120 gsm galvanized steel Indian standard. First Floor

Providing and Fixing of Armstrong OR equivalent GI Lay in Plain metal ceiling consisting of 600 x600 millimetre Lay in tiles of pre coated galvanized steel in 0.5 millimetre thickness in Global white color tile to be laid on Armstrong or equivalent grid systems with 15 millimetre wide T - section flanges color white having rotary stitching on the Main Runner, 1200 millimetre and 600 millimetre Cross Tees.Providing and Fixing of GI Lay in Plain metal ceiling consisting of 600x600 millimetre Lay in tiles of pre coated galvanized steel in 0.5 millimetre thickness in Global white color tile to be laid on grid systems with 15 millimetre wide T - section flanges color white having rotary stitching on the Main Runner, 1200 millimetre and 600 millimetre Cross Tees.products approved as per GRIHA and BS 476 Ground Floor

Providing and Fixing of Armstrong OR equivalent GI Lay in Plain metal ceiling consisting of 600 x600 millimetre Lay in tiles of pre coated galvanized steel in 0.5 millimetre thickness in Global white color tile to be laid on Armstrong or equivalent grid systems with 15 millimetre wide T - section flanges color white having rotary stitching on the Main Runner, 1200 millimetre and 600 millimetre Cross Tees.Providing and Fixing of GI Lay in Plain metal ceiling consisting of 600x600 millimetre Lay in tiles of pre coated galvanized steel in 0.5 millimetre thickness in Global white color tile to be laid on grid systems with 15 millimetre wide T - section flanges color white having rotary stitching on the Main Runner, 1200 millimetre and 600 millimetre Cross Tees.products approved as per GRIHA and BS 476 First Floor

Providing and Fixing in position, Fabric wrapped Compressed polyester fibre nonwoven 9 millimetre panels above the wood wool board panelling or existing sal wood frame, using adhesive, as per Architectural and Acoustical Design and Instructions and Complete in all aspects. including all materials labour,finishing etc. complete. First Floor

Providing and laying water proof treatment of terrace slab with brick bat coba in all position with an average thickness of 150 milimetre consisting specialised materials as per the manufactures specifications and covering 10 years guarantee on court fee stamp paper including all lead, lift, etc. complete. Ground Floor

Providing and laying water proof treatment of terrace slab with brick bat coba in all position with an average thickness of 150 milimetre consisting specialised materials as per the manufactures specifications and covering 10 years guarantee on court fee stamp paper including all lead, lift, etc. complete. Second Floor

Providing and applying two coats of High Albedo paint having minimum Solar Reflective Index (SRI) 108 (with solar reflectance and thermal emittance tested as per ASTM) C 1549 and ASTM C 1371 respectively, VOC less than 10 cc/gm. The coating thickness and the methodology of application shall strctly as per manufacturer's specifitions and as approved by engineer in charge. Surface preparation includes cleaning with metal wire brush to remove all dust, fungus etc, washing with water all complete.The contractor shall give guarantee for the performance of SRI and also the durabitity of coating, all complete as per direction of Engineer - in- incharge.Ground Floor

Providing and applying two coats of High Albedo paint having minimum Solar Reflective Index (SRI) 108 (with solar reflectance and thermal emittance tested as per ASTM) C 1549 and ASTM C 1371 respectively, VOC less than 10 cc/gm. The coating thickness and the methodology of application shall strctly as per manufacturer's specifitions and as approved by engineer in charge. Surface preparation includes cleaning with metal wire brush to remove all dust, fungus etc, washing with water all complete.The contractor shall give guarantee for the performance of SRI and also the durabitity of coating, all complete as per direction of Engineer - in- incharge.First Floor

Providing and applying two coats of High Albedo paint having minimum Solar Reflective Index (SRI) 108 (with solar reflectance and thermal emittance tested as per ASTM) C 1549 and ASTM C 1371 respectively, VOC less than 10 cc/gm. The coating thickness and the methodology of application shall strctly as per manufacturer's specifitions and as approved by engineer in charge. Surface preparation includes cleaning with metal wire brush to remove all dust, fungus etc, washing with water all complete.The contractor shall give guarantee for the performance of SRI and also the durabitity of coating, all complete as per direction of Engineer - in- incharge.Second Floor

Providing and applying water proofing treatment using acrylic polymer modified cement based water proofing coating with fibre glass mesh mixing at the rate of powder to liquid (2:1) by weight covering 9 to 10 square metre with two coats using Dr. Fixit or alike of chemicals for masonry and concrete surface by brush covering 7 years guarantee on Stamp Papers etc. complete First Floor

Providing and applying water proofing treatment using acrylic polymer modified cement based water proofing coating with fibre glass mesh mixing at the rate of powder to liquid (2:1) by weight covering 9 to 10 square metre with two coats using Dr. Fixit or alike of chemicals for masonry and concrete surface by brush covering 7 years guarantee on Stamp Papers etc. complete Second Floor

Providing waterproof bedding for flooring of Bath and water closet 25 millimetre thickin cement mortar 1:3 including using approved waterproofing compound in specified proportion as per manufacturers specifications for per bag of cement including leveling,curing and covering10 years guarantee on court fee stamp paper of Rs.500/- including ponding test etc. complete. First Floor

Providing waterproof bedding for flooring of Bath and water closet 25 millimetre thickin cement mortar 1:3 including using approved waterproofing compound in specified proportion as per manufacturers specifications for per bag of cement including leveling,curing and covering10 years guarantee on court fee stamp paper of Rs.500/- including ponding test etc. complete. Second Floor

Three Track Two Glass + One Net Shutter Window :Providing and fixing aluminium system color anodized sliding window of various sizes. Window will be made from Geeta/ Utility/ Econova 25 to 27 millimetre slim series or equivalent System. Window will be of specially extruded aluminium 3Track - 2 Glass + 1 net shutter, track joints will be of 45 degree joints, joints will be fixed with specially developed clits. Track frame will be fixed to the masonry opening of windows with S S 202 screws. Glass shutter will be made from specially extruded aluminium section, glass considered is 5 millimetre clear toughened glass. All shutter will be having 45 degree joints, joints will be fixed with specially developed clits to form uniform hairline joint. All shutter will be fixed to the main frame with necessary double roller to have smooth and easy movement of the shutter. Shutters will have single point self pressing lock. All fixing screws will be of S S 202. Windows will be sealed with weather sealant from outer periphery, etc. complete. Ground Floor

Three Track Two Glass + One Net Shutter Window :Providing and fixing aluminium system color anodized sliding window of various sizes. Window will be made from Geeta/ Utility/ Econova 25 to 27 millimetre slim series or equivalent System. Window will be of specially extruded aluminium 3Track - 2 Glass + 1 net shutter, track joints will be of 45 degree joints, joints will be fixed with specially developed clits. Track frame will be fixed to the masonry opening of windows with S S 202 screws. Glass shutter will be made from specially extruded aluminium section, glass considered is 5 millimetre clear toughened glass. All shutter will be having 45 degree joints, joints will be fixed with specially developed clits to form uniform hairline joint. All shutter will be fixed to the main frame with necessary double roller to have smooth and easy movement of the shutter. Shutters will have single point self pressing lock. All fixing screws will be of S S 202. Windows will be sealed with weather sealant from outer periphery, etc. complete. First Floor

Three Track Two Glass + One Net Shutter Window :Providing and fixing aluminium system color anodized sliding window of various sizes. Window will be made from Geeta/ Utility/ Econova 25 to 27 millimetre slim series or equivalent System. Window will be of specially extruded aluminium 3Track - 2 Glass + 1 net shutter, track joints will be of 45 degree joints, joints will be fixed with specially developed clits. Track frame will be fixed to the masonry opening of windows with S S 202 screws. Glass shutter will be made from specially extruded aluminium section, glass considered is 5 millimetre clear toughened glass. All shutter will be having 45 degree joints, joints will be fixed with specially developed clits to form uniform hairline joint. All shutter will be fixed to the main frame with necessary double roller to have smooth and easy movement of the shutter. Shutters will have single point self pressing lock. All fixing screws will be of S S 202. Windows will be sealed with weather sealant from outer periphery, etc. complete. Second Floor

Providing and fixing in position aluminium partly openable and partly fixed window of any size as per detailed drawing and as directed by Engineer incharge with all necessary alluminium sections including necessary fixtures and fastening with 5 millimetre thick float glass etc.complete.b) With powder coating Note While arriving at the rate of item of item weight at 6.90 Kilogram/Square Metre is considered. Ground Floor

Providing and fixing in position aluminium partly openable and partly fixed window of any size as per detailed drawing and as directed by Engineer incharge with all necessary alluminium sections including necessary fixtures and fastening with 5 millimetre thick float glass etc.complete.b) With powder coating Note While arriving at the rate of item of item weight at 6.90 Kilogram/Square Metre is considered. First Floor

Providing and fixing in position aluminium partly openable and partly fixed window of any size as per detailed drawing and as directed by Engineer incharge with all necessary alluminium sections including necessary fixtures and fastening with 5 millimetre thick float glass etc.complete.b) With powder coating Note While arriving at the rate of item of item weight at 6.90 Kilogram/Square Metre is considered. Second Floor

Four Track Three Glass + One Net Shutter Window :Providing and fixing aluminium system color anodized sliding window of various sizes. Window will be made from Geeta / Utility/Econova 25 to 27 millimetre slim series or equivalent System. Windows will be of specially extruded aluminium 3Track - 3 Glass + 1 net shutter, track joints will be of 45 degree joints, joints will be fixed with specially developed clits. Track frame will be fixed to the masonry opening of windows with S S 202 screws. Glass shutter will be made from specially extruded aluminium section, glass considered is 5 millimetre clear toughened glass. All shutter will be having 45 degree joints, joints will be fixed with specially developed clits to form uniform hairline joint. All shutter will be fixed to the main frame with necessary double roller to have smooth and easy movement of the shutter. Shutters will have single point self pressing lock. All fixing screws will be of S S 202. Windows will be sealed with weather sealant from outer periphery, etc. complete. First Floor

Two Track Two Glass Shutter Window : Providing and fixing aluminium color anodized system sliding window of various sizes. Window will be made from Geeta / Utility/Econova, 25 to 27 millimetre slim series or equivalent System. Windows will be of specially extruded aluminium 2 Track - 2 Glass shutter window/ ventilator, track joints will be of 45 degree joints, joints will be fixed with specially developed clits. Track frame will be fixed to the masonry opening of windows with stainless steel 202 screws. Glass shutter will be made from specially extruded aluminium section, glass considered is 5 millimetre clear toughened glass. All shutter will be having 45 degree joints, joints will be fixed with specially developed clits to form uniform hairline joint. All shutter will be fixed to the main frame with necessary double roller to have smooth and easy movement of the shutter. Shutters will have single point self pressing lock. All fixing screws will be of S S 202. Windows will be sealed with weather sealant from outer periphery, etc. complete. Ground Floor

Two Track Two Glass Shutter Window : Providing and fixing aluminium color anodized system sliding window of various sizes. Window will be made from Geeta / Utility/Econova, 25 to 27 millimetre slim series or equivalent System. Windows will be of specially extruded aluminium 2 Track - 2 Glass shutter window/ ventilator, track joints will be of 45 degree joints, joints will be fixed with specially developed clits. Track frame will be fixed to the masonry opening of windows with stainless steel 202 screws. Glass shutter will be made from specially extruded aluminium section, glass considered is 5 millimetre clear toughened glass. All shutter will be having 45 degree joints, joints will be fixed with specially developed clits to form uniform hairline joint. All shutter will be fixed to the main frame with necessary double roller to have smooth and easy movement of the shutter. Shutters will have single point self pressing lock. All fixing screws will be of S S 202. Windows will be sealed with weather sealant from outer periphery, etc. complete. First Floor

Two Track Two Glass Shutter Window : Providing and fixing aluminium color anodized system sliding window of various sizes. Window will be made from Geeta / Utility/Econova, 25 to 27 millimetre slim series or equivalent System. Windows will be of specially extruded aluminium 2 Track - 2 Glass shutter window/ ventilator, track joints will be of 45 degree joints, joints will be fixed with specially developed clits. Track frame will be fixed to the masonry opening of windows with stainless steel 202 screws. Glass shutter will be made from specially extruded aluminium section, glass considered is 5 millimetre clear toughened glass. All shutter will be having 45 degree joints, joints will be fixed with specially developed clits to form uniform hairline joint. All shutter will be fixed to the main frame with necessary double roller to have smooth and easy movement of the shutter. Shutters will have single point self pressing lock. All fixing screws will be of S S 202. Windows will be sealed with weather sealant from outer periphery, etc. complete. Second Floor

Aluminium System Color Anodized Fixed Window : Providing and fixing aluminium system color anodized fixed window of various sizes. Casement will be made from Geeta / Utility/ Econova 40 millimetre series or equivalent System. Windows will be of specially extruded aluminium section, joints will be of 45 degree joints, joints will be fixed with specially developed clits. Track frame will be fixed to the masonry opening of windows with S S 202 wood screws. Fixed glass casement will be made from specially extruded aluminum section, glass considered is 5 millimetre clear toughened glass. All shutter will be having 45 degree joints, joints will be fixed with specially developed clits to form uniform hairline joint. All fixing screws will be of S S 202. Windows will be sealed with weather sealant from outer periphery, etc. complete. Ground Floor

Aluminium System Color Anodized Fixed Window : Providing and fixing aluminium system color anodized fixed window of various sizes. Casement will be made from Geeta / Utility/ Econova 40 millimetre series or equivalent System. Windows will be of specially extruded aluminium section, joints will be of 45 degree joints, joints will be fixed with specially developed clits. Track frame will be fixed to the masonry opening of windows with S S 202 wood screws. Fixed glass casement will be made from specially extruded aluminum section, glass considered is 5 millimetre clear toughened glass. All shutter will be having 45 degree joints, joints will be fixed with specially developed clits to form uniform hairline joint. All fixing screws will be of S S 202. Windows will be sealed with weather sealant from outer periphery, etc. complete. First Floor

Providing and fixing in position anodised (as per IS1868/1982) Aluminium fixed staggered (ZType) Ventilator with aluminium rectangular pipe 63 millimetre x 38.10 millimetre x1.22 millimetre at weight 0.650 Kilogramme per Running metre, Aluminium angle of size15 millimetre x 15 millimetre x 1 millimetre ,aluminium channel of 9 millimetre sizes, stainless steel mosquito net of 304 Grade,4 millimetre thick float glass per detailed drawing and as directed by Engineer in charge etc.complete. Ground Floor

Providing and fixing in position anodised (as per IS1868/1982) Aluminium fixed staggered (ZType) Ventilator with aluminium rectangular pipe 63 millimetre x 38.10 millimetre x1.22 millimetre at weight 0.650 Kilogramme per Running metre, Aluminium angle of size15 millimetre x 15 millimetre x 1 millimetre ,aluminium channel of 9 millimetre sizes, stainless steel mosquito net of 304 Grade,4 millimetre thick float glass per detailed drawing and as directed by Engineer in charge etc.complete.First Floor

Providing and fixing in position powder coated aluminium louvered windows/ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 millimetre x 38 millimetre x 1.22 millimetre box type, 5 millimetre thick sheet glass louvers,of approved quality etc. complete. Ground Floor

Providing and fixing in position powder coated aluminium louvered windows/ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 millimetre x 38 millimetre x 1.22 millimetre box type, 5 millimetre thick sheet glass louvers,of approved quality etc. complete. First Floor

Providing and fixing in position powder coated aluminium louvered windows/ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 millimetre x 38 millimetre x 1.22 millimetre box type, 5 millimetre thick sheet glass louvers,of approved quality etc. complete. Second Floor

Openable Shutter in Structural Glazing : Providing and fixing openable shutter in structural glazing work of 5 millimetre teak tented toughened glass with frame work made of aluminum RHS of size 64 millimetre x 58 millimetre color anodized as per design and drawing, aluminum sections should be confirming IS 63400 , glass pasted to frame work with 3M VHB tape and DOW CORNING 995 silicon sealant and gaps between glass panels should be filled by clear Dow CORNING 789 silicon weather proofing sealant , with good quality stainless steel friction hinges, rubber gaskets handles all necessary fasteners and accessories complete. First Floor

Structural Glazing : Providing and fixing structural glazing work of 5 millimetre thick tinted toughened glass with frame work made of aluminum RHS of size 64 millimetre x 58 millimetre color anodized as per design and drawing, aluminum sections should be confirming Indian Standard 63400 , glass pasted to frame work with 3M VHB tape and DOW CORNING 995 silicon sealant and gaps between glass panels should be filled by clear Dow CORNING 789 silicon weather proofing sealant , with all necessary fasteners and accessories complete Second Floor

Providing and fixing frame with/ without ventilator of size as specified with Country cut teak wood for doors and windows including chamfering,rounding, rebating, iron hold fast of size300 millimetre x 40 millimetre x 5 millimetre with oil painting, etc. complete Ground Floor

Providing and fixing frame with/ without ventilator of size as specified with Country cut teak wood for doors and windows including chamfering,rounding, rebating, iron hold fast of size300 millimetre x 40 millimetre x 5 millimetre with oil painting, etc. complete First Floor

Providing and fixing frame with/ without ventilator of size as specified with Country cut teak wood for doors and windows including chamfering,rounding, rebating, iron hold fast of size300 millimetre x 40 millimetre x 5 millimetre with oil painting, etc. complete Second Floor

Providing and fixing 34 millimetre thick moulded door shutter consisting of solid core single leaf flush door of 30 millimetre thickness lipped with15 millimetre (5 millimetre x3) thick x 30 millimetre width on one style and top rail and 10 millimetre (5 millimetre x2) thick x 30 millimetre width on other style and bottom rails.The inner panels laminated with 2 millimetre thick termiteproof,waterproof and fire resistant moulded poly vinyl chloride sheet with 2,4,6 design in different plain and/ or pre lim colours on one side after routing the moulded design on flush doors and 2 millimetre plain and /or pre lam poly vinyl chloride on other side using rubber adhesive on flush door and solvent cement adhesive on the poly vinyl chloride lipping etc.as per direction of Engineer incharge and manufacturers specification and drawing etc.complete. Ground Floor

Providing and fixing 34 millimetre thick moulded door shutter consisting of solid core single leaf flush door of 30 millimetre thickness lipped with15 millimetre (5 millimetre x3) thick x 30 millimetre width on one style and top rail and 10 millimetre (5 millimetre x2) thick x 30 millimetre width on other style and bottom rails.The inner panels laminated with 2 millimetre thick termiteproof,waterproof and fire resistant moulded poly vinyl chloride sheet with 2,4,6 design in different plain and/ or pre lim colours on one side after routing the moulded design on flush doors and 2 millimetre plain and /or pre lam poly vinyl chloride on other side using rubber adhesive on flush door and solvent cement adhesive on the poly vinyl chloride lipping etc.as per direction of Engineer incharge and manufacturers specification and drawing etc.complete. First Floor

Providing and fixing 34 millimetre thick moulded door shutter consisting of solid core single leaf flush door of 30 millimetre thickness lipped with15 millimetre (5 millimetre x3) thick x 30 millimetre width on one style and top rail and 10 millimetre (5 millimetre x2) thick x 30 millimetre width on other style and bottom rails.The inner panels laminated with 2 millimetre thick termiteproof,waterproof and fire resistant moulded poly vinyl chloride sheet with 2,4,6 design in different plain and/ or pre lim colours on one side after routing the moulded design on flush doors and 2 millimetre plain and /or pre lam poly vinyl chloride on other side using rubber adhesive on flush door and solvent cement adhesive on the poly vinyl chloride lipping etc.as per direction of Engineer incharge and manufacturers specification and drawing etc.complete. Second Floor

Providing and Fixing 30 millimetre thick BOTH SIDE PRELAMINATED SOLID PANEL poly vinyl chloride DOOR SHUTTER consisting of frame made out of mild steel tubes of 19 guage thickness and, size 19 x 19 millimetre for styles and 15 x15 millimetre for the top and bottom rails, mild steel frame shall have a coat of metel primer of approved make and manufacture. M.S frame shall be covered with heat mouled poly vinyl chloride 'C' channel made from 5 millimetre (+/0.25) thick prelaminated sheet of density 600 kg/cbm ,of size 30 millimetre thickness 70 millimetre width out of which 50 millimetre shall be flat and 20 millimetre shall be tapered in 45 angle on either side forming stiles ; and 5 millimetre thick ,95 millimetre wide poly vinyl chloride sheet out of which 75 millimetre shall be falt and 20 millimetre shall be tapered in 45 on the inner side to form top and bottom rail and 115 millimetre wide poly vinyl chloride sheet out of which 75 millimetre shall be falt and 20 millimetre shall be tapered on both sides to form lock rail.Top,bottom and lock rail shall be provided either side of the panel. An additional 5 millimetre (+/0.25) thick poly vinyl chloride strip of 20 millimetre width is to be stuck on the bottom side of the ' c ' channel prelaminated paneling of 5 millimetre (+/0.25) thick poly vinyl chloride sheet to be fitted inside the M.S. frame welded/ sealed to the styles and rails with 5 millimetre (+/0.25) x 30 millimetre poly vinyl chloride sheet beading on either side and joined together with solvent cementadhesive etc ,10 millimetre thickness (5 millimetre (+/0.25) x 2 Numbers ) 20 millimetre wide. Ground Floor

Providing and Fixing 30 millimetre thick BOTH SIDE PRELAMINATED SOLID PANEL poly vinyl chloride DOOR SHUTTER consisting of frame made out of mild steel tubes of 19 guage thickness and, size 19 x 19 millimetre for styles and 15 x15 millimetre for the top and bottom rails, mild steel frame shall have a coat of metel primer of approved make and manufacture. M.S frame shall be covered with heat mouled poly vinyl chloride 'C' channel made from 5 millimetre (+/0.25) thick prelaminated sheet of density 600 kg/cbm ,of size 30 millimetre thickness 70 millimetre width out of which 50 millimetre shall be flat and 20 millimetre shall be tapered in 45 angle on either side forming stiles ; and 5 millimetre thick ,95 millimetre wide poly vinyl chloride sheet out of which 75 millimetre shall be falt and 20 millimetre shall be tapered in 45 on the inner side to form top and bottom rail and 115 millimetre wide poly vinyl chloride sheet out of which 75 millimetre shall be falt and 20 millimetre shall be tapered on both sides to form lock rail.Top,bottom and lock rail shall be provided either side of the panel. An additional 5 millimetre (+/0.25) thick poly vinyl chloride strip of 20 millimetre width is to be stuck on the bottom side of the ' c ' channel prelaminated paneling of 5 millimetre (+/0.25) thick poly vinyl chloride sheet to be fitted inside the M.S. frame welded/ sealed to the styles and rails with 5 millimetre (+/0.25) x 30 millimetre poly vinyl chloride sheet beading on either side and joined together with solvent cementadhesive etc ,10 millimetre thickness (5 millimetre (+/0.25) x 2 Numbers ) 20 millimetre wide. First Floor

Providing and fixing solid core flush door shutter in double leaf 32 millimetre thick decorative type of exterior grade as per detailed drawings approved face veneers 3 millimetre thick on both faces or as directed,all necessary beads,mouldings and lipping,wrought iron hold fasts,chromium plated fixtures and fastenings,with brass mortise lock,chromium plated handles on both sides, and finishing with French Polish etc. complete. Ground Floor

Providing and fixing solid core flush door shutter in double leaf 32 millimetre thick decorative type of exterior grade as per detailed drawings approved face veneers 3 millimetre thick on both faces or as directed,all necessary beads,mouldings and lipping,wrought iron hold fasts,chromium plated fixtures and fastenings,with brass mortise lock,chromium plated handles on both sides, and finishing with French Polish etc. complete. First Floor

Providing and fixing solid core flush door shutter in double leaf 32 millimetre thick decorative type of exterior grade as per detailed drawings approved face veneers 3 millimetre thick on both faces or as directed,all necessary beads,mouldings and lipping,wrought iron hold fasts,chromium plated fixtures and fastenings,with brass mortise lock,chromium plated handles on both sides, and finishing with French Polish etc. complete. Second Floor

Providing and fixing glass door size 1.0 metre /1.2 metre x 2.7 metre single leaf shutter of 12 millimetre thick toughen glass froasted and edge polish as shown in the drawings or as directed, including all necessary fittings like Hydraulic Bottom Patch Fitting, top patch fittings, bottom patch fittings, door handle door lock at base, door soft central 180 weather seal for door edges and BWP grade 12 millimetre thick fixed toughen glass froasted as per drawings having glass fixing sections at all sides concealed in partitions etc. complete as directed by Engineer -IN-Charge Ground Floor

Providing and fixing rolling shutter fabricated from steellaths of minimum thickness 0.9 millimetre with lock plate of 3.15 millimetre thickness reinforced with 35x35x5 millimetre angle section fitted with sliding bolts and handles for both sides,deep mild steel channel section of depth and thickness not less than 65 millimetre and 3.15 millimetre respectively with hold fast arrangements, mild steel Bracket plate 300 millimetre x 300 millimetre x 3.15 millimetre minimum size and shape with square bar,suspension shaft of minimum 32 millimetre diameter,hood cover of mild steel sheet not less than 0.9 millimetre thickness and of any size at top and safety devices including mechanical gear operation arrangement consisting of worm gear wheels and worms of high grade cast iron or mild steel and one coat of red lead primer etc. complete. (Indian Standard 62481979) (With mechanical gear) Ground Floor

Providing and fixing Luxalon SL4 84R plain panel sun louvers manufactured by M/s Hunter Douglas India Pvt. Ltd. of approved color consisting of panel 84 millimetre wide 16 millimetre deep x 0.6 millimetre thick with round edges panel length up to 6 Metre coil coated on continues paint Line double baked and roll formed from enameled corrosion resistance. Aluminium Alloy AA3005 (Al. Mg.) for higher strength and good roll forming characteristics Panel shall be clipped to baked enameled aluminium SL-4 panel stringer of 33 millimetre wide and 86 millimetre deep X 0.95 millimetre thick in a standard Length of 5 Metre made of double baked enameled Aluminium alloy AA5050 (Al. Mg.) black with cut-outs to hold the panel in a module of 86 millimetre center to center at a distance of 1 Mt. The Carrier shall be fixed to suitable structure by means of rigid fixing details including Paint Finish : Aluminium panels shall be cromotised for maximum bond between metal and paint enameled twice under high temperature one side with full primer and luxacoat finish. The other side (Inner side) with a primer coat and skin coat on a continuous paint line etc.complete as directed by Engineer-in-charge. Ground Floor

Providing and fixing Luxalon SL4 84R plain panel sun louvers manufactured by M/s Hunter Douglas India Pvt. Ltd. of approved color consisting of panel 84 millimetre wide 16 millimetre deep x 0.6 millimetre thick with round edges panel length up to 6 Metre coil coated on continues paint Line double baked and roll formed from enameled corrosion resistance. Aluminium Alloy AA3005 (Al. Mg.) for higher strength and good roll forming characteristics Panel shall be clipped to baked enameled aluminium SL-4 panel stringer of 33 millimetre wide and 86 millimetre deep X 0.95 millimetre thick in a standard Length of 5 Metre made of double baked enameled Aluminium alloy AA5050 (Al. Mg.) black with cut-outs to hold the panel in a module of 86 millimetre center to center at a distance of 1 Mt. The Carrier shall be fixed to suitable structure by means of rigid fixing details including Paint Finish : Aluminium panels shall be cromotised for maximum bond between metal and paint enameled twice under high temperature one side with full primer and luxacoat finish. The other side (Inner side) with a primer coat and skin coat on a continuous paint line etc.complete as directed by Engineer-in-charge.First Floor

Verticle Fins : Providing and fixing vertical fins made up of aluminium rectangular box section of size 127 millimetre x 38.10 millimetre and 1.74 millimetre thick at 125 millimetre center to center spacing, fixed with aluminiun support sections at top and bottom, finished with grey / black/ brown colored matt anodizing etc.complete as directed by Engineer-in-charge. Ground Floor

erticle Fins : Providing and fixing vertical fins made up of aluminium rectangular box section of size 127 millimetre x 38.10 millimetre and 1.74 millimetre thick at 125 millimetre center to center spacing, fixed with aluminiun support sections at top and bottom, finished with grey / black/ brown colored matt anodizing etc.complete as directed by Engineer-in-charge. First Floor

Providing and fixing Indian Standard Institute marked double swing flush door shutters conforming to Indian Standard :2202 In Rs.(Part I) Non-decorative type, core of block board construction with frame of 1st class hardwood and well matched teak 3 ply veneering with vertical grains or cross bands and faceveneers on both faces of shutters. 30 millimetre thick including Indian Standard Institute marked Stainless Steel L- hingeswith necessary screws Fittings and Fixtures per leaf stainless steel kick plates on both sides of the door of 300 millimetre heightHeavy Duty satin finish butt SS Hinges (100 millimetre x 75 millimetre x 3 millimetre in size) -4 nos. stainless steel finishedlever handle with mortise lock- 1 NumberFloor spring- 1 Number 100 millimetre x 100 millimetre safety glass at the specified location Ground Floor

Providing and fixing Indian Standard Institute marked double swing flush door shutters conforming to Indian Standard :2202 In Rs.(Part I) Non-decorative type, core of block board construction with frame of 1st class hardwood and well matched teak 3 ply veneering with vertical grains or cross bands and faceveneers on both faces of shutters. 30 millimetre thick including Indian Standard Institute marked Stainless Steel L- hingeswith necessary screws Fittings and Fixtures per leaf stainless steel kick plates on both sides of the door of 300 millimetre heightHeavy Duty satin finish butt SS Hinges (100 millimetre x 75 millimetre x 3 millimetre in size) -4 nos. stainless steel finishedlever handle with mortise lock- 1 NumberFloor spring- 1 Number 100 millimetre x 100 millimetre safety glass at the specified location First Floor

Providing and fixing Indian Standard Institute marked double swing flush door shutters conforming to Indian Standard :2202 In Rs.(Part I) Non-decorative type, core of block board construction with frame of 1st class hardwood and well matched teak 3 ply veneering with vertical grains or cross bands and faceveneers on both faces of shutters. 30 millimetre thick including Indian Standard Institute marked Stainless Steel L- hingeswith necessary screws Fittings and Fixtures per leaf stainless steel kick plates on both sides of the door of 300 millimetre heightHeavy Duty satin finish butt SS Hinges (100 millimetre x 75 millimetre x 3 millimetre in size) -4 nos. stainless steel finishedlever handle with mortise lock- 1 NumberFloor spring- 1 Number 100 millimetre x 100 millimetre safety glass at the specified location Second Floor

Providing and Fixing mat finish stainless steel (of 302 grade) railing with top pipe of 50 milimetre diameter and vertical pipe of 38 milimetre diameter at 0.60 metre center to center or as required and horizontal pipes of 25 milimetre diameter in three rows, all pipes of 2 milimetre thick including buffing,fabricating fixtures and fastening including pipe base of appropriate diameter and ball base of 75 milimetre diameter above newel post of 75 milimetre diameter etc. complete. Ground Floor

Providing and Fixing mat finish stainless steel (of 302 grade) railing with top pipe of 50 milimetre diameter and vertical pipe of 38 milimetre diameter at 0.60 metre center to center or as required and horizontal pipes of 25 milimetre diameter in three rows, all pipes of 2 milimetre thick including buffing,fabricating fixtures and fastening including pipe base of appropriate diameter and ball base of 75 milimetre diameter above newel post of 75 milimetre diameter etc. complete. First Floor

Providing and Fixing mat finish stainless steel (of 302 grade) railing with top pipe of 50 milimetre diameter and vertical pipe of 38 milimetre diameter at 0.60 metre center to center or as required and horizontal pipes of 25 milimetre diameter in three rows, all pipes of 2 milimetre thick including buffing,fabricating fixtures and fastening including pipe base of appropriate diameter and ball base of 75 milimetre diameter above newel post of 75 milimetre diameter etc. complete. Second Floor

stainless steel Railing : Providing and Fixing matt finished stainless steel (Grade 304) railing with 60 millimetre x 40 millimetre and 1.6 millimetre thick pipe as handrail at top, 40 millimetre x 8 millimetre vertical patti placed at 1148 millimetre center to center, 40 millimetre x 8 millimetre horizontal patti placed at bottom 100 millimetre above the flooring,12 millimetre diameter pipe placed vertically in between handrail and bottom patti at 150 millimetre centre to centre and 75 millimetre centre to centre alternately as shown in the drawing. including buffing, fabricating fixtures and fastening including base or cover plate of appropriate size as directed by Engineer in charge etc. Complete. Ground Floor

stainless steel Railing : Providing and Fixing matt finished stainless steel (Grade 304) railing with 60 millimetre x 40 millimetre and 1.6 millimetre thick pipe as handrail at top, 40 millimetre x 8 millimetre vertical patti placed at 1148 millimetre center to center, 40 millimetre x 8 millimetre horizontal patti placed at bottom 100 millimetre above the flooring,12 millimetre diameter pipe placed vertically in between handrail and bottom patti at 150 millimetre centre to centre and 75 millimetre centre to centre alternately as shown in the drawing. including buffing, fabricating fixtures and fastening including base or cover plate of appropriate size as directed by Engineer in charge etc. Complete. First Floor

stainless steel Railing : Providing and Fixing matt finished stainless steel (Grade 304) railing with 60 millimetre x 40 millimetre and 1.6 millimetre thick pipe as handrail at top, 40 millimetre x 8 millimetre vertical patti placed at 1148 millimetre center to center, 40 millimetre x 8 millimetre horizontal patti placed at bottom 100 millimetre above the flooring,12 millimetre diameter pipe placed vertically in between handrail and bottom patti at 150 millimetre centre to centre and 75 millimetre centre to centre alternately as shown in the drawing. including buffing, fabricating fixtures and fastening including base or cover plate of appropriate size as directed by Engineer in charge etc. Complete. Second Floor

Providing and constructing granite kitchen platform with fixing of stainless steel sink 600 millimetre x 450 millimetre size as per detailed drawing including vertical both side polished kadappah stone 25 to 30 millimetre thick supports with kadappah top 35 to 40 millimetre thick and polished granite 16 to 20 millimetre top with side strips of granite at front and both sides of platform raised with two vertical granite supports 15 centimetre height and top granite of 75 x 40 centimetre including cutting, opening for sink of required size in kadappah as well as granite etc. complete. Ground Floor

Providing and constructing granite kitchen platform with fixing of stainless steel sink 600 millimetre x 450 millimetre size as per detailed drawing including vertical both side polished kadappah stone 25 to 30 millimetre thick supports with kadappah top 35 to 40 millimetre thick and polished granite 16 to 20 millimetre top with side strips of granite at front and both sides of platform raised with two vertical granite supports 15 centimetre height and top granite of 75 x 40 centimetre including cutting, opening for sink of required size in kadappah as well as granite etc. complete. First Floor

Providing and constructing granite kitchen platform with fixing of stainless steel sink 600 millimetre x 450 millimetre size as per detailed drawing including vertical both side polished kadappah stone 25 to 30 millimetre thick supports with kadappah top 35 to 40 millimetre thick and polished granite 16 to 20 millimetre top with side strips of granite at front and both sides of platform raised with two vertical granite supports 15 centimetre height and top granite of 75 x 40 centimetre including cutting, opening for sink of required size in kadappah as well as granite etc. complete. Second Floor

Providing and fixing sink cock with regular swinging spout (Wall Mounted Model) with wall flange with approved make incluidng other necessary fitting, etc. complete as directed by Engineer in charge. Ground Floor

Providing and fixing sink cock with regular swinging spout (Wall Mounted Model) with wall flange with approved make incluidng other necessary fitting, etc. complete as directed by Engineer in charge. First Floor

Providing and fixing sink cock with regular swinging spout (Wall Mounted Model) with wall flange with approved make incluidng other necessary fitting, etc. complete as directed by Engineer in charge. Second Floor

Providing and Fixing stainless steel kitchen trolley of overall 26 inch height and 22 inch depth,supported on aluminium pipes ,trolley basket made out of 5 millimetre stainless steel rod fitted on telescopic channel of size 1.5 inch x 20 inch x 22 inch on both sides of trolley of 12 inch or above size, panel having 40 kg load bearing capacity of trolley made out of 20 millimetre PUC coated plywood and colour combination as directed by E-I-C.Inner side of panel covered by white mica ,100 millimetre stainless steel decorative handle.(The width and height of individual compartments shall be kept as directed by Engineer-in-charge) Ground Floor

Providing and Fixing stainless steel kitchen trolley of overall 26 inch height and 22 inch depth,supported on aluminium pipes ,trolley basket made out of 5 millimetre stainless steel rod fitted on telescopic channel of size 1.5 inch x 20 inch x 22 inch on both sides of trolley of 12 inch or above size, panel having 40 kg load bearing capacity of trolley made out of 20 millimetre PUC coated plywood and colour combination as directed by E-I-C.Inner side of panel covered by white mica ,100 millimetre stainless steel decorative handle.(The width and height of individual compartments shall be kept as directed by Engineer-in-charge) First Floor

Providing and Fixing stainless steel kitchen trolley of overall 26 inch height and 22 inch depth,supported on aluminium pipes ,trolley basket made out of 5 millimetre stainless steel rod fitted on telescopic channel of size 1.5 inch x 20 inch x 22 inch on both sides of trolley of 12 inch or above size, panel having 40 kg load bearing capacity of trolley made out of 20 millimetre PUC coated plywood and colour combination as directed by E-I-C.Inner side of panel covered by white mica ,100 millimetre stainless steel decorative handle.(The width and height of individual compartments shall be kept as directed by Engineer-in-charge) Second Floor

Providing and fixing European type wall-hung white water closet of approved make with push valve concealed type with cover plate 32 millimetre size of approved make including soilpipe,ventpipe up to out side face of wall,100 millimetre diameter G.I.plug bend inlet pipe all fittings,cuttingand making good walls, floors etc. complete. Ground Floor

Providing and fixing European type wall-hung white water closet of approved make with push valve concealed type with cover plate 32 millimetre size of approved make including soilpipe,ventpipe up to out side face of wall,100 millimetre diameter G.I.plug bend inlet pipe all fittings,cuttingand making good walls, floors etc. complete. First Floor

Providing and fixing white european type wall-hung, of size 360 millimetre x 360 millimetre x 575 millimetre withflush valve of approved make including soil pipe, vent pipe upto outside face of wall,100 millimetre dia cast iron plug bend inlet pipe all fittings,cutting and making good walls, floors etc asdirected by Engineer in charge. Ground Floor

Providing and fixing white european type wall-hung, of size 360 millimetre x 360 millimetre x 575 millimetre withflush valve of approved make including soil pipe, vent pipe upto outside face of wall,100 millimetre dia cast iron plug bend inlet pipe all fittings,cutting and making good walls, floors etc asdirected by Engineer in charge. First Floor

Providing and fixing white european type wall-hung, of size 360 millimetre x 360 millimetre x 575 millimetre withflush valve of approved make including soil pipe, vent pipe upto outside face of wall,100 millimetre dia cast iron plug bend inlet pipe all fittings,cutting and making good walls, floors etc asdirected by Engineer in charge. Second Floor

Providing and fixing white european type wall-hung pan, of size 350 millimetre x 355 millimetre x 570 millimetre concealed flush tank with floor-mounting frame installing, kit and drain pipe connectionset for wall hung water closet, with approved make square control plates including soil pipe, vent pipeupto the outside face of wall, 100 millimetre dia cast iron plug bend inlet pipe all fittings,cutting and making good walls, floors etc. complete. Ground Floor

Providing and fixing white european type wall-hung pan, of size 350 millimetre x 355 millimetre x 570 millimetre concealed flush tank with floor-mounting frame installing, kit and drain pipe connectionset for wall hung water closet, with approved make square control plates including soil pipe, vent pipeupto the outside face of wall, 100 millimetre dia cast iron plug bend inlet pipe all fittings,cutting and making good walls, floors etc. complete. First Floor

Providing and fixing white european type wall-hung pan, of size 350 millimetre x 355 millimetre x 570 millimetre concealed flush tank with floor-mounting frame installing, kit and drain pipe connectionset for wall hung water closet, with approved make square control plates including soil pipe, vent pipeupto the outside face of wall, 100 millimetre dia cast iron plug bend inlet pipe all fittings,cutting and making good walls, floors etc. complete. Second Floor

Providing and fixing Orissa Pan of size 580 millimetre x 445 millimetre x 260 millimetre with approved make flush valve including trap,cast iron soil and vent pipe upto out side face of wall including 100 millimetre diameter cast iron plug, bend and necessary pipe connection, etc complete as directed by Engineer in charge. Ground Floor

Providing and fixing Orissa Pan of size 580 millimetre x 445 millimetre x 260 millimetre with approved make flush valve including trap,cast iron soil and vent pipe upto out side face of wall including 100 millimetre diameter cast iron plug, bend and necessary pipe connection, etc complete as directed by Engineer in charge. First Floor

Providing and fixing white wash basin with half pedestal of size 515 millimetre X 615 millimetre X460 millimetre including pillar cock auto-closing system chromium plated angular stop cock long thread of approved make continental including stainless steel bottle trap of necessary pipe connection upto the out side face of the wall. Ground Floor

Providing and fixing white wash basin with half pedestal of size 515 millimetre X 615 millimetre X460 millimetre including pillar cock auto-closing system chromium plated angular stop cock long thread of approved make continental including stainless steel bottle trap of necessary pipe connection upto the out side face of the wall. First Floor

Providing and fixing wall-hung white wash basin of size 470 millimetre x 575 millimetre x 190 millimetre of approved make half pedestal,pillar cock,chromium plated .Angular stop cock,long thread continental including stainless steel bottle trap of having necessary pipe connections upto the out side face of the wall.etc complete. Ground Floor

Providing and fixing wall-hung white wash basin of size 470 millimetre x 575 millimetre x 190 millimetre of approved make half pedestal,pillar cock,chromium plated .Angular stop cock,long thread continental including stainless steel bottle trap of having necessary pipe connections upto the out side face of the wall.etc complete. First Floor

providing and fixing oval type under counter wash hand basin of 16 inch x 22 inch size and of special colour shade having telephonic black/coloured granite of 180 millimetre thick stone black kadappa frame work including chromium plated coupling bottle-Trapusing CERA company or equivalent oval typa wash basin model No.3448 as per detailed drawing or as directed by engg incharge etc complete. (Counter size 1.20 metre x 0.60 metre) Ground Floor

Providing and fixing Auto closing pillar cock of press matic tap of approved make or equivalent including all fixtures, fittings etc. complete. Ground Floor

Providing and fixing Oval Type Under Counter Wash Hand Basin of 420 millimetre x 590 millimetre x195 millimetre size with pillar cock, chromium plated .Angular stop cock,long thread of approved make continental including stainless steel bottle trap of necessary pipe connection up to the out side face of the wall,having Telephonic Black/Colour Graniteof 180 millimetre thick fixedon Black Kadappa Framework, etc. Complete as directed by Engineer in charge. Ground Floor

Providing and fixing Oval Type Under Counter Wash Hand Basin of 420 millimetre x 590 millimetre x195 millimetre size with pillar cock, chromium plated .Angular stop cock,long thread of approved make continental including stainless steel bottle trap of necessary pipe connection up to the out side face of the wall,having Telephonic Black/Colour Graniteof 180 millimetre thick fixedon Black Kadappa Framework, etc. Complete as directed by Engineer in charge. First Floor

Providing and fixing Oval Type Under Counter Wash Hand Basin of 420 millimetre x 590 millimetre x195 millimetre size with pillar cock, chromium plated .Angular stop cock,long thread of approved make continental including stainless steel bottle trap of necessary pipe connection up to the out side face of the wall,having Telephonic Black/Colour Graniteof 180 millimetre thick fixedon Black Kadappa Framework, etc. Complete as directed by Engineer in charge. Second Floor

Providing and fixing Table top white wash basin of size120x635x405 millimetre rubber plugs and brass chain,with pillar cock, chromium plated Angular stop cock longthread,continental including stainless steel bottle trap of approved make having necessary pipe connection upto the out side face of the wall.etc complete as directed by Engineer in charge. Ground Floor

Providing and fixing Table top white wash basin of size120x635x405 millimetre rubber plugs and brass chain,with pillar cock, chromium plated Angular stop cock longthread,continental including stainless steel bottle trap of approved make having necessary pipe connection upto the out side face of the wall.etc complete as directed by Engineer in charge. First Floor

Providing and fixing Table top white wash basin of size120x635x405 millimetre rubber plugs and brass chain,with pillar cock, chromium plated Angular stop cock longthread,continental including stainless steel bottle trap of approved make having necessary pipe connection upto the out side face of the wall.etc complete as directed by Engineer in charge. Second Floor

Providing and fixing white glazed urinal of series with Pressmatic autoclosing valve of having 32 millimetre diameter poly vinyl chloride flush pipe with fitting and flushing of approved make and arrangement including lead soil pipe,lead trapand soil pipe connection upto the out side face of wall etc.complete as directed by Engineer in charge. Ground Floor

Providing and fixing white glazed urinal of series with Pressmatic autoclosing valve of having 32 millimetre diameter poly vinyl chloride flush pipe with fitting and flushing of approved make and arrangement including lead soil pipe,lead trapand soil pipe connection upto the out side face of wall etc.complete as directed by Engineer in charge. First Floor

Providing and fixing of approved make white aqua free Water less Urinal of with cartride size of 31.5 centimetre x 33 centimetre x 60 centimetre including other necessary fittings etc. complete. First Floor

Providing and Fixing toilet set for differently Abled persons consist of Floor Mounted white vitreous china water Closet including 6litre capacity white vitreous china flushing Cistern with raised soft-push button,white vitreous china wash basin of size 46 centimetre x 36 centimetre and one no SS304 hinged rail76centimetre s and three no SS304 of (GrabBar) 60 centimetre sall including cutting and making good the wall sand floors where ver required,seatcover,cisternand wash basin fittings,nuts, bolts and gasket etc complete as per the direction of Engineer-In-charge. Ground Floor

Providing and Fixing toilet set for differently Abled persons consist of Floor Mounted white vitreous china water Closet including 6litre capacity white vitreous china flushing Cistern with raised soft-push button,white vitreous china wash basin of size 46 centimetre x 36 centimetre and one no SS304 hinged rail76centimetre s and three no SS304 of (GrabBar) 60 centimetre sall including cutting and making good the wall sand floors where ver required,seatcover,cisternand wash basin fittings,nuts, bolts and gasket etc complete as per the direction of Engineer-In-charge. First Floor

Providing and fixing Shower Head with shower arm of approved make shower tube hand shower with divert or of spout including all necessary pipe fitting sand connection setc.complete as directed by Engineer in charge. Ground Floor

Providing and fixing Shower Head with shower arm of approved make shower tube hand shower with divert or of spout including all necessary pipe fitting sand connection setc.complete as directed by Engineer in charge. First Floor

Providing and fixing Shower Head with shower arm of approved make shower tube hand shower with divert or of spout including all necessary pipe fitting sand connection setc.complete as directed by Engineer in charge. Second Floor

Providing and fixing chromium plated .Two way BIB cock of approved make continental including necessary sockets/union nut etc. Ground Floor

Providing and fixing chromium plated .Two way BIB cock of approved make continental including necessary sockets/union nut etc. First Floor

Providing and fixing chromium plated a 2-Way BIB cock with wall flange of approved make including necessary sockets/ union nut etc. complete as directed by Engineer in charge. Ground Floor

Providing and fixing chromium plated a 2-Way BIB cock with wall flange of approved make including necessary sockets/ union nut etc. complete as directed by Engineer in charge. First Floor

Providing and fixing chromium plated 2 Way BIB cock with wall flange of approved make including necessary sockets/ union nut etc. complete as directed by Engineer in charge. First Floor

Providing and fixing chromium plated Toilet paper holder of approved make including necessary sockets/ union nut etc. complete Ground Floor

Providing and fixing chromium plated Toilet paper holder of approved make including necessary sockets/ union nut etc. complete First Floor

Providing and fixing Hand shower (health faucet) with 8 millimetre diameter 1 m long flexible tube having wall hook with approved make including necessary sockets /unionnut etc.complete as directed by Engineer in charge. Ground Floor

Providing and fixing Hand shower (health faucet) with 8 millimetre diameter 1 m long flexible tube having wall hook with approved make including necessary sockets /unionnut etc.complete as directed by Engineer in charge. First Floor

Providing and fixing chromium plated BIB cock with wall flange of approved make including necessary sockets/ union nut etc. complete. Ground Floor

Providing and fixing chromium plated BIB cock with wall flange of approved make including necessary sockets/ union nut etc. complete. First Floor

Providing and fixing on walls/ceiling/floor 15 millimetre diameter chlorinated poly vinyl chloride pipe with necessary fittings,remaking good the demolished portion etc.complete.Including removing existing pipeline if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete. Ground Floor

Providing and fixing on walls/ceiling/floor 15 millimetre diameter chlorinated poly vinyl chloride pipe with necessary fittings,remaking good the demolished portion etc.complete.Including removing existing pipeline if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete. First Floor

Providing and fixing on walls/ceiling/floor 15 millimetre diameter chlorinated poly vinyl chloride pipe with necessary fittings,remaking good the demolished portion etc.complete.Including removing existing pipeline if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete. Second Floor

Providing and fixing on walls/ceiling/floor 20 millimetre diameter chlorinated poly vinyl chloride pipe with necessary fittings,remaking good the demolished portion etc.complete.Including removing existing pipeline if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete. Ground Floor

Providing and fixing on walls/ceiling/floor 20 millimetre diameter chlorinated poly vinyl chloride pipe with necessary fittings,remaking good the demolished portion etc.complete.Including removing existing pipeline if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete. First Floor

Providing and fixing on walls/ceiling/floor 20 millimetre diameter chlorinated poly vinyl chloride pipe with necessary fittings,remaking good the demolished portion etc.complete.Including removing existing pipeline if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete. Second Floor

Providing and fixing on walls/ceiling/floor 25 millimetre diameter chlorinated poly vinyl chloride pipe with necessary fittings,remaking good the demolished portion etc.complete.Including removing existing pipeline if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete. Ground Floor

Providing and fixing on walls/ceiling/floor 25 millimetre diameter chlorinated poly vinyl chloride pipe with necessary fittings,remaking good the demolished portion etc.complete.Including removing existing pipeline if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete. First Floor

Providing and fixing on walls/ceiling/floor 25 millimetre diameter chlorinated poly vinyl chloride pipe with necessary fittings,remaking good the demolished portion etc.complete.Including removing existing pipeline if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete.Second Floor

Providing and fixing on walls/ceiling/floor 32 millimetre diameter chlorinated poly vinyl chloride pipe with necessary fittings,remaking good the demolished portion etc.complete.Including removing existing pipeline if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete. Ground Floor

Providing and fixing on walls/ceiling/floor 32 millimetre diameter chlorinated poly vinyl chloride pipe with necessary fittings,remaking good the demolished portion etc.complete.Including removing existing pipeline if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete. First Floor

Providing and fixing on walls/ceiling/floor 32 millimetre diameter chlorinated poly vinyl chloride pipe with necessary fittings,remaking good the demolished portion etc.complete.Including removing existing pipeline if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete. Second Floor

Providing and fixing on walls/ceiling/floor 40 millimetre diameter chlorinated poly vinyl chloride pipe with necessary fittings,remaking good the demolished portion etc.complete.Including removing existing pipeline if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete Ground Floor

Providing and fixing on walls/ceiling/floor 40 millimetre diameter chlorinated poly vinyl chloride pipe with necessary fittings,remaking good the demolished portion etc.complete.Including removing existing pipeline if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete First Floor

Providing and fixing on walls/ceiling/floor 40 millimetre diameter chlorinated poly vinyl chloride pipe with necessary fittings,remaking good the demolished portion etc.complete.Including removing existing pipeline if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete Second Floor

Providing and fixing on walls/ceiling/floor 50 millimetre diameter chlorinated poly vinyl chloride pipe with necessary fittings,remaking good the demolished portion etc.complete.Including removing existing pipeline if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete. Ground Floor

Providing and fixing on walls/ceiling/floor 50 millimetre diameter chlorinated poly vinyl chloride pipe with necessary fittings,remaking good the demolished portion etc.complete.Including removing existing pipeline if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete. First Floor

Providing and fixing on walls/ceiling/floor 50 millimetre diameter chlorinated poly vinyl chloride pipe with necessary fittings,remaking good the demolished portion etc.complete.Including removing existing pipeline if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete. Second Floor

Providing and laying in trenches 25 millimetre diameter medium grade having embossed as Indian Standard Institute Mark galvanised iron pipes of 2.49 kilogramme per metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint,2 coats Including removing existing pipe line if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete. Ground Floor

Providing and laying in trenches 25 millimetre diameter medium grade having embossed as Indian Standard Institute Mark galvanised iron pipes of 2.49 kilogramme per metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint,2 coats Including removing existing pipe line if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete. First Floor

Providing and laying in trenches 40 millimetre diameter medium grade having embossed as Indian Standard Institute Mark galvanised iron pipes of 2.49 kilogramme per metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint, 2 coats Including removing existing pipe line if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete. Ground Floor

Providing and laying in trenches 40 millimetre diameter medium grade having embossed as Indian Standard Institute Mark galvanised iron pipes of 2.49 kilogramme per metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint, 2 coats Including removing existing pipe line if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete. First Floor

Zinc Roofing : Supply and Installation of VMZINC - ZINC Titanium Alloy 25/430 STANDING SEAM ROOFING SYSTEM of approved color shade in 0.7 millimetre thickness. Zinc Titanium Alloy comprIndian Standard Instituteng of the layers. 1) Top layer – VMZINC - Zinc titanium alloy standing seam profiled panels 25 /430 (25 millimetre seam height and 430 millimetre panel width) manufactured from zinc titanium alloy in 0.7 millimetre minimum thickness and pre weathered Quartz plus finish .The material properties shall be as follows: Ultimate tensile strength: minimum 150 N/ millimetre 2,0.2 Percent Proof Stress: min 100 N/ millimetre 2, Modulus of elasticity: 90,000 N/ millimetre 2 Panels shall be fixed to the substructure using Stainless Steel clips fixing and sliding clips of suitable height with spacing as required for the wind loads. The zinc roof sheets shall have a protection on its underside consisting of a 60 micron thick composite acrylate-urethane protective coating. The roofing sheets shall be as per EN 988 standards .The roofing shall be installed with the help of all the required machines / tools and design assistance. 2) Second Layer - Anti Abrasive brethable membrane to be laid underneath the Zinc roofing sheets. 3) Third Layer - 1.0 millimetre thick GI strips / Pieces to placed at suitable distance for fixing of special SS clips 4) Fourth Layer - 0.47 millimetre TCT Bare Galvalume Hi-Tensile steel sheets profile with nominal 3.5 millimetre deep ribs at pitch of nominal 50 millimetre centre to centre distance 550 MPa Yield Strength. The micro liner - decking sheet shall be fixed over the Mild Steel purlins provided by Main Contractor. MS Box Section / GI Z Purlins to be provided by Main Contractor at distance of 600 millimetre Centre to centre maximum for fixing of above mentioned Specialize roofing built up layers. Gutter (if required) to be continued as per Roofing built up with maximum upto 1000 millimetre Girth. Second Floor

Supply and Installation of 0.7 millimetre zinc flashing having girth upto 166 millimetre in the same finish as the roof finish for eaves, gables, ridges, fascia, gutters, etc. as required for site detailing Box Section / galvanised Z Purlins to be provided by Main Contractor at distance of 600 millimetre Centre to centre maximum for fixing of above mentioned Specialize roofing built up layers. Gutter (if required) to be continued as per Roofing built up with maximum upto 1000 millimetre Girth. Second Floor

Supply and Installation of VMZINC - ZINC Titanium Alloy 25/430 STANDING SEAM SOFFIT CLADING SYSTEM of approved color shade in 0.8 millimetre thickness. Zinc Titanium Alloy comprIndian Standard Instituteng of the layers. ) Top layer – VMZINC Quartz Strat finish standing seam profiled Soffit panels having 25 millimetre seam height and 430 millimetre panel width to be manufactured from zinc titanium alloy in 0.8 millimetre miniumum thickness.The material properties shall be as follows:Ultimate tensile strength: minimum 150 N/ millimetre 2,0.2 Percent , Proof Stress: min 100 N/ millimetre 2, Modulus of elasticity: 90,000 N/ millimetre 2. Panels shall be fixed to the substructure using Stainelss Steel clips fixing and sliding clips of suitable height with spacing as per required wind loads parameters. The zinc soffit cladding sheets shall have a proprietary transparent protection on its topside consisting of 15 microns thick Clear Polyurethane protective coating. The soffit cladding sheets shall be as per EN 988 standards .The zinc manufacturer shall have all the required machines / tools and design assistance 2) Second Layer - Anti Abrasive brethable membrane / Synthetic Mesh to be laid underneath the roofing sheets. 3) Third Layer - 1.0 millimetre thick galvanised iron strips / Pieces to placed at suitable distance for fixing of special stainless steel clips 4) Fourth Layer - 0.47 millimetre TCT Bare Galvalume Hi-Tensile steel sheets profile with nominal 3.5 millimetre deep ribs at pitch of nominal 50 millimetre centre to centre distance 550 MPa Yield Strength.The micro liner - decking sheet shall be fixed over the Mild Steel purlins provided. Second Floor

Providing and fabricating structural steel work in rolled sections like joists, channels, angles, tees etc. as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted /bolted / welded connections without connecting plates, braces etc. and including one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete. Ground Floor

Providing and fabricating structural steel work in rolled sections like joists, channels, angles, tees etc. as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted /bolted / welded connections without connecting plates, braces etc. and including one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete. First Floor

Providing and fabricating structural steel work in rolled sections like joists, channels, angles, tees etc. as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted /bolted / welded connections without connecting plates, braces etc. and including one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete. Second Floor

Providing and fixing 20 to 25 milimetre thick rough shahabad box type waterproofing for basement or underground floor on a base of Cement concrete 1:3:6, including sub base of 2.50 centimetre thick Cement mortar 1:3 with conceal, setcrete (RMW), Algaeproof or other alike water proofing liquids, raking of joints upto 35 milimetre depth,filling the joints with 6 milimetre size crushed metal, hand grouting with cement slurry, curing and cleaning, with 7 years guarantee on court fee stamp of Rs. 100/- with ponding test etc complete. (excluding Cement concrete 1:3:6 base concrete).

Providing and fixing 20 to 25 milimetre thick rough shahabad box type waterproofing treatment to vertical outside faces of Reinforced Cement concrete walls of basement or underground floor including filling the gap of 25 milimetre between rough shahabad and Reinforced Cement concrete walls with cement grout mixed with water proofing liquid Algaeproof or other alike with one tile lift method, brushing the joints horizontally with cement slurry mixed with water proofing liquid for width 30 to 35 milimetre and sloping coping over topmost tile with cement mortar 1:3, butting the bottom most with Cement concrete 1:2:4 mixed with water proofing liquid, curing, with 7 years guarantee on court fee stamp of Rs. 100/- with ponding test etc complete. (excluding Cement concrtete 1:3:6 base concrete).

Providing and fixing 75 millimetre diameter stabiliser pipe/ poly vinyl chloride soil vent/waste pipe and withnecessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. Complete Ground Floor

Providing and fixing 75 millimetre diameter stabiliser pipe/ poly vinyl chloride soil vent/waste pipe and withnecessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. Complete First Floor

Providing and fixing 75 millimetre diameter stabiliser pipe/ poly vinyl chloride soil vent/waste pipe and withnecessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. Complete Second Floor

Providing and fixing 100 millimetre diameter stabiliser pipe/ poly vinyl chloride soil vent/waste pipe and withnecessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete. Ground Floor

Providing and fixing 100 millimetre diameter stabiliser pipe/ poly vinyl chloride soil vent/waste pipe and withnecessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete. First Floor

Providing and fixing 100 millimetre diameter stabiliser pipe/ poly vinyl chloride soil vent/waste pipe and withnecessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete. Second Floor

Providing and fixing poly vinyl chloride Rain water pipes of 110 millimetre outer diameter and having wallthickness of 2.2 to 2.7 millimetre confirming to Indian Standard 13592-1992 including proper rainwaterreceiving recess with poly vinyl chloride plug, bend, necessary fittings, such as, offsets, shoes, inludingfixing the pipe on wall using approved wooden cleats projecting 25 millimetre to 40 millimetre from face ofwall a fixing with clips of approved quality and number ,filing the joint using rubber gasketwith solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks,including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations ofpipes. All the poly vinyl chloride fittings and additional 2 piece socket clips shall be got approved fromengineer in charge etc. complete. Ground Floor

Providing and fixing poly vinyl chloride Rain water pipes of 110 millimetre outer diameter and having wallthickness of 2.2 to 2.7 millimetre confirming to Indian Standard 13592-1992 including proper rainwaterreceiving recess with poly vinyl chloride plug, bend, necessary fittings, such as, offsets, shoes, inludingfixing the pipe on wall using approved wooden cleats projecting 25 millimetre to 40 millimetre from face ofwall a fixing with clips of approved quality and number ,filing the joint using rubber gasketwith solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks,including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations ofpipes. All the poly vinyl chloride fittings and additional 2 piece socket clips shall be got approved fromengineer in charge etc. complete. First Floor

Providing and fixing poly vinyl chloride Rain water pipes of 110 millimetre outer diameter and having wallthickness of 2.2 to 2.7 millimetre confirming to Indian Standard 13592-1992 including proper rainwaterreceiving recess with poly vinyl chloride plug, bend, necessary fittings, such as, offsets, shoes, inludingfixing the pipe on wall using approved wooden cleats projecting 25 millimetre to 40 millimetre from face ofwall a fixing with clips of approved quality and number ,filing the joint using rubber gasketwith solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks,including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations ofpipes. All the poly vinyl chloride fittings and additional 2 piece socket clips shall be got approved fromengineer in charge etc. complete. Second Floor

Providing expansion joints in reinforced cement concrete framed structure (interior columns) with plain premoulded filler with confirming to Indian Standard 1838,1961, 25 millimetre thick with 75 millimetre wide and 1 millimetre thick stainless steel plate finishing etc. complete as directed Ground Floor

Providing expansion joints in reinforced cement concrete framed structure (at floor level) with plain premoulded filler 25 millimetre thick with 75 millimetre wide and 1 millimetre thick stainless steel plat and finishing etc. complete. Ground Floor

Providing expansion joints in reinforced cement concrete framed structure (at Terrace level) with premoulded filler 25 millimetre thick with 40 millimetre wide and 1 millimetre thick stainless steel plate as required, bitumen poured filler and finishing etc. complete as directed. First Floor

Providing and laying in situ/ Ready Mix cement concrete Mix-20 of trap metal for Reinforced Cement Concrete work in foundations like raft, strip foundations, grillage and footings of Reinforced Cement Concrete columns and steel stanchions etc. including bailing out water, formwork, laying/ pumping cover blocks, compaction and curing roughening the surface if special finish is to be provided, (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based Progra millimetre able Logic Controller with Supervisory Control and Data Acquisition enabled Concrete Batch Mix plant (Pan mixer) etc. complete, with fine aggregate (Natural Sand/ Crushed Sand Vertical shaft impact (VSI) Grade finely washed etc.)

Providing and laying cast in situ/ Ready Mix cement concrete Mix-20 of trap metal for Reinforced Cement Concrete columns as per detailed designs and drawing or as directed including centering, formwork, cover blocks, laying/ pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete, (Excluding reinforcement and structural steel) with fully automatic micro processor based Progra millimetre able Logic Controller with Supervisory Control and Data Acquisition enabled Concrete Batch Mix plant (Pan mixer) etc. complete with fine aggregate (Natural Sand/ Crushed Sand Vertical shaft impact (VSI) Grade finely washed etc.) Ground Floor

Providing and laying cast in situ/ Ready Mix cement concrete Mix-20 of trap metal for Reinforced Cement Concrete columns as per detailed designs and drawing or as directed including centering, formwork, cover blocks, laying/ pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete, (Excluding reinforcement and structural steel) with fully automatic micro processor based Progra millimetre able Logic Controller with Supervisory Control and Data Acquisition enabled Concrete Batch Mix plant (Pan mixer) etc. complete with fine aggregate (Natural Sand/ Crushed Sand Vertical shaft impact (VSI) Grade finely washed etc.) First Floor

Providing and laying cast in situ/ Ready Mix cement concrete Mix-20 of trap metal for Reinforced Cement Concrete columns as per detailed designs and drawing or as directed including centering, formwork, cover blocks, laying/ pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete, (Excluding reinforcement and structural steel) with fully automatic micro processor based Progra millimetre able Logic Controller with Supervisory Control and Data Acquisition enabled Concrete Batch Mix plant (Pan mixer) etc. complete with fine aggregate (Natural Sand/ Crushed Sand Vertical shaft impact (VSI) Grade finely washed etc.) Second Floor

Providing and laying Cast in situ/ Ready Mix cement concrete Mix-20 of trap metal for Reinforced Cement Concrete Beams and Lintels as per detailed designs and drawings or as directed including centering, formwork, cover blocks, laying/ pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel), with fully automatic micro processor based Progra millimetre able Logic Controller with Supervisory Control and Data Acquisition enabled Concrete Batch Mix plant (Pan mixer) etc. complete with fine aggregate (Natural Sand/ Crushed Sand Vertical shaft impact (VSI) Grade finely washed etc.) Ground Floor

Providing and laying Cast in situ/ Ready Mix cement concrete Mix-20 of trap metal for Reinforced Cement Concrete Beams and Lintels as per detailed designs and drawings or as directed including centering, formwork, cover blocks, laying/ pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel), with fully automatic micro processor based Progra millimetre able Logic Controller with Supervisory Control and Data Acquisition enabled Concrete Batch Mix plant (Pan mixer) etc. complete with fine aggregate (Natural Sand/ Crushed Sand Vertical shaft impact (VSI) Grade finely washed etc.) First Floor

Providing and laying Cast in situ/ Ready Mix cement concrete Mix-20 of trap metal for Reinforced Cement Concrete Beams and Lintels as per detailed designs and drawings or as directed including centering, formwork, cover blocks, laying/ pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel), with fully automatic micro processor based Progra millimetre able Logic Controller with Supervisory Control and Data Acquisition enabled Concrete Batch Mix plant (Pan mixer) etc. complete with fine aggregate (Natural Sand/ Crushed Sand Vertical shaft impact (VSI) Grade finely washed etc.) Second Floor

Providing and laying Cast in situ/ Ready Mix cement concrete Mix-20 of trap metal for Reinforced Cement Concrete Slabs and Landings as per detailed designs and drawings including centering, formwork, cover blocks, laying/ pumping, compactionfinishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete, (Excluding reinforcement and structural steel) with fully automatic micro processor based Progra millimetre able Logic Controller with Supervisory Control and Data Acquisition enabled Concrete Batch Mix plant (Pan mixer) etc. complete, with fine aggregate (Natural Sand/ Crushed Sand Vertical shaft impact (VSI) Grade finely washed etc.) Ground Floor

Providing and laying Cast in situ/ Ready Mix cement concrete Mix-20 of trap metal for Reinforced Cement Concrete Slabs and Landings as per detailed designs and drawings including centering, formwork, cover blocks, laying/ pumping, compactionfinishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete, (Excluding reinforcement and structural steel) with fully automatic micro processor based Progra millimetre able Logic Controller with Supervisory Control and Data Acquisition enabled Concrete Batch Mix plant (Pan mixer) etc. complete, with fine aggregate (Natural Sand/ Crushed Sand Vertical shaft impact (VSI) Grade finely washed etc.) First Floor

Providing and laying Cast in situ/ Ready Mix cement concrete Mix-20 of trap metal for Reinforced Cement Concrete Slabs and Landings as per detailed designs and drawings including centering, formwork, cover blocks, laying/ pumping, compactionfinishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete, (Excluding reinforcement and structural steel) with fully automatic micro processor based Progra millimetre able Logic Controller with Supervisory Control and Data Acquisition enabled Concrete Batch Mix plant (Pan mixer) etc. complete, with fine aggregate (Natural Sand/ Crushed Sand Vertical shaft impact (VSI) Grade finely washed etc.) Second Floor

Providing and laying Cast in situ/ Ready Mix cement concrete in Mix-20 of trap metal for Reinforced Cement Concrete Waist Slab, and steps of staircases as per detailed design and drawings or as directed including steel centering, plywood/ steel formwork, steel props, laying/ pumping, compaction, finishing uneven and honeycombed surface with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete, with fully automatic micro processor based Progra millimetre able Logic Controller with Supervisory Control and Data Acquisition enabled Concrete Batch Mix plant (Pan mixer) etc. complete, with fine aggregate (Natural Sand/ Crushed Sand Vertical shaft impact (VSI) Grade finely washed etc.) (Excluding einforcement, including cover block).(Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin ). Ground Floor

Providing and laying Cast in situ/ Ready Mix cement concrete in Mix-20 of trap metal for Reinforced Cement Concrete Waist Slab, and steps of staircases as per detailed design and drawings or as directed including steel centering, plywood/ steel formwork, steel props, laying/ pumping, compaction, finishing uneven and honeycombed surface with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete, with fully automatic micro processor based Progra millimetre able Logic Controller with Supervisory Control and Data Acquisition enabled Concrete Batch Mix plant (Pan mixer) etc. complete, with fine aggregate (Natural Sand/ Crushed Sand Vertical shaft impact (VSI) Grade finely washed etc.) (Excluding einforcement, including cover block).(Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin ). First Floor

Providing and laying Cast in situ/ Ready Mix cement concrete in Mix-20 of trap metal for Reinforced Cement Concrete Waist Slab, and steps of staircases as per detailed design and drawings or as directed including steel centering, plywood/ steel formwork, steel props, laying/ pumping, compaction, finishing uneven and honeycombed surface with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete, with fully automatic micro processor based Progra millimetre able Logic Controller with Supervisory Control and Data Acquisition enabled Concrete Batch Mix plant (Pan mixer) etc. complete, with fine aggregate (Natural Sand/ Crushed Sand Vertical shaft impact (VSI) Grade finely washed etc.) (Excluding einforcement, including cover block).(Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin ). Second Floor

Providing and laying Cast in situ/Ready Mix cement concrete in M-20 of trap metal for reinforced cement concrete pardi of required thickness including steel centering,formwork, cover blocks, laying/pumping, compacting , curing , finishing and rougheningthemif special finish is to be provided and curing complete.(Excluding reinforcement andstructural steel).with fully automatic micro processor based PLC with SCADA enabled Concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Ground Floor

Providing and laying Cast in situ/Ready Mix cement concrete in M-20 of trap metal for reinforced cement concrete pardi of required thickness including steel centering,formwork, cover blocks, laying/pumping, compacting , curing , finishing and rougheningthemif special finish is to be provided and curing complete.(Excluding reinforcement andstructural steel).with fully automatic micro processor based PLC with SCADA enabled Concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) First Floor

Providing and laying Cast in situ/Ready Mix cement concrete in M-20 of trap metal for reinforced cement concrete pardi of required thickness including steel centering,formwork, cover blocks, laying/pumping, compacting , curing , finishing and rougheningthemif special finish is to be provided and curing complete.(Excluding reinforcement andstructural steel).with fully automatic micro processor based PLC with SCADA enabled Concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Second Floor

Providing and errecting chain link fencing 1.6 metre height with galvanised iron chain link of size 50 x 50 milimetre 8 guage thick and fixed 75 milimetre above Ground level on vertical Mild Steel Angle of 40x40x6 milimetre size including excavating pits for foundation and embeded in cement concrete block of 1:4:8 mix of size 450x450x670 milimetre at 1.75 metre center to center with iron bar 16 milimetre diameter as hold fast including welding link with angle frame at 30 centimetre . c/c nuts and bolts and horizontal Mild Steel Angles at top and bottom of 25x25x5 metre size and vertical Mild Steel flat 35 x 5 metre and 25 x 5 metre horizontal including cross support of 40x40x6 metre Angles both sides at every corner or bends embeded in concrete blocks of 1:4:8 of size 450x450x670 milimetre including 3 coats of oil painting etc. complete. Ground Floor

Providing and fixing Indian teak wood planking 50 millimetre thick for flooring planed on both sides, tounged and groved including scaffolding, if necessary, and one coat of primer complete. Ground Floor

Providing and fixing Indian teak wood planking 50 millimetre thick for flooring planed on both sides, tounged and groved including scaffolding, if necessary, and one coat of primer complete. First Floor

Providing cement based water proofing treatment to terraces (Indian water proofing or alike) with brick bats laid in required slope to drain the water for any span after cleaning the base surface. Applying a coat of cement slurry admixed with approved water proofing compound and laying the brick bats on bottom layer in cement mortar 1:5 admixed with approved water proofing compound filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with cement mortar1:3 admixed with approved water proofing compound and finally top finishing with average 20 milimetre thick layers of same mortar added with jute fiber at 1 kilogram per bag including finishing the surface smooth with cement slurry admixed with approved water proofing compound. Marking finished surface with false squares of 300 milimetre x 300 milimetre making the junctions at the parapet rounded and tapered top for required height, with drip mould at the junction of plaster and parapet and curing and covering 10 years Guarantee against leakproofness on Court fee stamp paper of Rs. 500/- including ponding test etc. complete. Ground Floor

Providing cement based water proofing treatment to terraces (Indian water proofing or alike) with brick bats laid in required slope to drain the water for any span after cleaning the base surface. Applying a coat of cement slurry admixed with approved water proofing compound and laying the brick bats on bottom layer in cement mortar 1:5 admixed with approved water proofing compound filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with cement mortar1:3 admixed with approved water proofing compound and finally top finishing with average 20 milimetre thick layers of same mortar added with jute fiber at 1 kilogram per bag including finishing the surface smooth with cement slurry admixed with approved water proofing compound. Marking finished surface with false squares of 300 milimetre x 300 milimetre making the junctions at the parapet rounded and tapered top for required height, with drip mould at the junction of plaster and parapet and curing and covering 10 years Guarantee against leakproofness on Court fee stamp paper of Rs. 500/- including ponding test etc. complete. First Floor

Providing cement based water proofing treatment to terraces (Indian water proofing or alike) with brick bats laid in required slope to drain the water for any span after cleaning the base surface. Applying a coat of cement slurry admixed with approved water proofing compound and laying the brick bats on bottom layer in cement mortar 1:5 admixed with approved water proofing compound filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with cement mortar1:3 admixed with approved water proofing compound and finally top finishing with average 20 milimetre thick layers of same mortar added with jute fiber at 1 kilogram per bag including finishing the surface smooth with cement slurry admixed with approved water proofing compound. Marking finished surface with false squares of 300 milimetre x 300 milimetre making the junctions at the parapet rounded and tapered top for required height, with drip mould at the junction of plaster and parapet and curing and covering 10 years Guarantee against leakproofness on Court fee stamp paper of Rs. 500/- including ponding test etc. complete.Second Floor

Providing and fixing Shower Head, with shower arm of approved make mixer of including In all necessary pipe fittings and connections etc. complete as directed by Engineer in charge. Ground Floor

Providing and fixing Shower Head, with shower arm of approved make mixer of including In all necessary pipe fittings and connections etc. complete as directed by Engineer in charge. First Floor

Providing and fixing Shower Head, with shower arm of approved make mixer of including In all necessary pipe fittings and connections etc. complete as directed by Engineer in charge. Second Floor

Providing and fixing 450 millimetre x 550 millimetre size superior type Belgium mirror with 16 millimetre diameter nickel plated towel rod etc. complete. Ground Floor

Providing and fixing 450 millimetre x 550 millimetre size superior type Belgium mirror with 16 millimetre diameter nickel plated towel rod etc. complete. First Floor

Providing and fixing 450 millimetre x 550 millimetre size superior type Belgium mirror with 16 millimetre diameter nickel plated towel rod etc. complete. Second Floor

Providing and fixing chromium plated . a 2-Way BIB cock with wall flange of approved make includingnecessary sockets/ union nut etc. complete as directed by Engineer in charge.And Providing and fixing Hand shower (health faucet) with 8 millimetre diameter 1m long flexible tubehaving wall hook with approved make including necessary sockets/ union nut etc. completeas directed by Engineer in charge. Ground Floor

Providing and fixing chromium plated . a 2-Way BIB cock with wall flange of approved make includingnecessary sockets/ union nut etc. complete as directed by Engineer in charge.And Providing and fixing Hand shower (health faucet) with 8 millimetre diameter 1m long flexible tubehaving wall hook with approved make including necessary sockets/ union nut etc. completeas directed by Engineer in charge. First Floor

Providing and fixing chromium plated . a 2-Way BIB cock with wall flange of approved make includingnecessary sockets/ union nut etc. complete as directed by Engineer in charge.And Providing and fixing Hand shower (health faucet) with 8 millimetre diameter 1m long flexible tubehaving wall hook with approved make including necessary sockets/ union nut etc. completeas directed by Engineer in charge. Second Floor

Providing and fixing 10 centimetre poly vinyl chloride nahani trap with grating etc. complete. Ground Floor

Providing and fixing 10 centimetre poly vinyl chloride nahani trap with grating etc. complete. First Floor

Providing and fixing 10 centimetre poly vinyl chloride nahani trap with grating etc. complete. Second Floor

Providing and fixing 15centimetre x 10centimetre salt glazed stoneware gully trap in cement concrete 1:4:8outside the building including cast iron grating in the sink, connecting glazed stoneware pipe,brick masonry chamber with cast iron lid and cast iron grating for the gully trap. Ground Floor

Excavation for roadway in earth soil of all sorts, sand, gravel or soft murum including dressing section to the required grade camber and side slopes and conveying the excavated materials with all lifts upto a lead of 50 m and spreading for embankment or stacking as directed.

Construction of granular sub-base by providing close graded Material, mixing in a mechanicalmix plant at optimum moisture content, carriage of mixed Material to work site, spreading in uniform layers withmotor grader/ Paver on prepared surface and compacting with vibratory roller to achieve thedesired density, complete as per clause 401 -- Plant Mix Method and Grading - I Material

Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate (Natural Sand/ Vertical shaft impact (VSI) grade finely washed Crushed Sand) conforming to Indian Standard: 383, the size of coarse aggregate not exceeding 25 milimetre, cement content not to be less than 150 kilogramme per cubic metre, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant/ Weigh batch mixer, transported to site with all leads and lifts, laid with a paver with electronic sensor/ by suitable means as approved by Engineer-in-charge, compacting with vibratory roller, finishing and curing including preparation of sub-grade surface if required etc. complete.

Providing and laying in-situ Mix-50 Grade unreinforced plain cement concrete pavement with maximum 20 percent Fly Ash (Fly-ash upto 20 Percent by weight of cement) over a prepared sub base with 43 grade cement , coarse and fine aggregate (Natural Sand/ VSI grade finely washed Crushed Sand) conforming to IS 383, using fine and coarse aggregates combined gradation as per Table 600-3 of MORTH Specification 2013, mixed in a Tilting type Concrete Mixer as per approved mix design, admixtures, spreading, laying, compacting and finished in a continuous operation, finishing to lines and grades as directed by Engineer-in-charge and curing by curing compound/ by providing cement vata in cement Mortar 1:8 of 0.6 metre x 0.6 metre centre to centre, admeasuring 80 milimetre at bottom and 40 milimetre at top with depth of 75 milimetre and maintaining the same throughout curing period/ by any other method approved by Engineer-in-charge.

Cutting transverse contraction joints 3 to 4 millimetre wide and depth 60millimetre .in concrete slab usingconcrete cutting machine with diamond studded saw within 48 hours of casting of bay / slabetc. complete including subsequent widening of the groove 8 to 10 millimetre wide at top havingdepth of 15 millimetre as directed by Engineer incharge.

Providing and fixing in position Thermo Mechanically Treated (TMT) FE 500, 32 millimetre dia dowel bars precoated withanticorrosive epoxy paint of required diameter 60 centimetre s. Long and at 30.00 centimetre . C/C and poly vinyl chloride pipe of 40 millimetre dia wherever directed including handling, straightening, necessary cutting supported by Thermo Mechanically Treated (TMT) FE 500, chairs with proper alignment by using properly designed assembly of Bulkheads lubricating half length with bituminous paint as directed etc. complete.

Providing and casting in situ or precast tapering reinforced cement concrete Mix-20 Semi Barrier type Kerb withoutgutter ( as per IRC 86 1983) embedded 125 millimetre below ground level over M-10 plain cement concrete finished neatly with cement mortar 1:2, setting the same in cement mortar 1:2, including the required excavation in anystrata and removing the excavated stuff any where in city and redoing the surface as specifiedand directed by Engineering In-charge. Using Concrete Batching and Mixing Plant

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting with Vibratory roller. to the required density. By Mechanical Means- Grading I, using Screening Type-A(13.2 milimetre Aggregate).

Providing and fixing heavy duty inter locking concrete Rubber mould glossy paving blocks of80 millimetre thickness of having a strength of 400 Kilogramme per square centimetre . of approved quality and shapeon a bed of crushed sand of 25 to 30 millimetre thick including skirting joints and cleaning etc.complete. (using 100 Percent crushed sand)

Providing and fixing white glazed urinal of size 710x460x300 millimetre with sensotronicconcealed type flushing valve for urinal with complete kit having fittings, inlet pipe with stoptap, brackets for fixing the cistern, 32 millimetre diameter poly vinyl chloride flush pipe with fitting and flushingarrangement including lead soil pipe, lead trap and soil pipe connection upto the outside face ofwall etc complete.Ground Floor

Providing and fixing colour coated Zincalume ( R ) AZ150 ( min 150 grams per square metre total on each side ) profiled sheets for roofing. The feed material is manufactured out of nominal 0.45 millimetre Base Metal Thickness ( BMT ) (0.5 millimetre TCT ), Hi-strength steel with minimum 550 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55% aluminium 43.4% zinc 1.6% silicon) with COLORBOND ( R ) steel quality super durable polyester paint coat ( with inorganic pigment). The paint shall have a total coating thickness of nominal 35 um, comprising of nominal 25 um exterior coat on top surface and nominal 10 um reverse coat on back surface. Profile sheet shall have nom. 950-1050 millimetre effective cover width and nominal 25-30 millimetre deep ribs with subtle square fluting in the five pan at nominal 180-250 mm center-to-center. The end rib shall be designed for anti-capillary groove and return leg. The feed material should have coil manufacturers product details marked a regular interval. Including fasteners with min. fastened with min. 25 um Zinc-Tin alloy coated, Hex head, self-drilling screw etc. complete. (weight of profile 4.52 Kilogramme per square metre) Ground Floor

Providing and fixing colour coated Zincalume ( R ) AZ150 ( min 150 grams per square metre total on each side ) profiled sheets for roofing. The feed material is manufactured out of nominal 0.45 millimetre Base Metal Thickness ( BMT ) (0.5 millimetre TCT ), Hi-strength steel with minimum 550 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55% aluminium 43.4% zinc 1.6% silicon) with COLORBOND ( R ) steel quality super durable polyester paint coat ( with inorganic pigment). The paint shall have a total coating thickness of nominal 35 um, comprising of nominal 25 um exterior coat on top surface and nominal 10 um reverse coat on back surface. Profile sheet shall have nom. 950-1050 millimetre effective cover width and nominal 25-30 millimetre deep ribs with subtle square fluting in the five pan at nominal 180-250 mm center-to-center. The end rib shall be designed for anti-capillary groove and return leg. The feed material should have coil manufacturers product details marked a regular interval. Including fasteners with min. fastened with min. 25 um Zinc-Tin alloy coated, Hex head, self-drilling screw etc. complete. (weight of profile 4.52 Kilogramme per square metre) First Floor

Providing and laying in situ cement concrete Mix-30 with tremix treatment for 200 millimetre thickness for Concrete Road is including laying plastic sheet for 125 micron thickness withgroove cutting of 4 millimetre wide and 20 millimetre deep with necessary refilling with polysuphidesealent (Pouring grade) confirming to BS : 5212 - 1989 into sawed groove widened at top forsealent reservoir of specified size and shape as per detailed drawing including fixingPolyethylene foam backer rod of required diameter ( excluding reinforcement) with coarsenand fine aggregate Using Vertical shaft impact (VSI) Quality Artifitial Sand etc. complete

Providing and fixing mild steel grill work for windows, ventilators etc.20 Kilogramme per square metre as per drawing including fixtures,necessary welding and painting with one coats of anti corrosive paint and two coats of oil painting complete. Ground Floor

Providing and fixing mild steel grill work for windows, ventilators etc.20 Kilogramme per square metre as per drawing including fixtures,necessary welding and painting with one coats of anti corrosive paint and two coats of oil painting complete. First Floor

Providing and fixing mild steel grill work for windows, ventilators etc.20 Kilogramme per square metre as per drawing including fixtures,necessary welding and painting with one coats of anti corrosive paint and two coats of oil painting complete. Second Floor

Providing internal cement plaster 20 millimetre thick in Single coats in cement mortar 1:3 without neeru finish, to concrete, brick surface, in all positions including scaffolding and curing etc.complete. Ground Floor

Providing and fixing machine cut mirror polished 18 millimetre to 20 millimetre thick telephone blackgranite / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone partition withfull moulding the edges etc. complete . Both side polish Ground Floor

Providing and fixing machine cut mirror polished 18 millimetre to 20 millimetre thick telephone blackgranite / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone partition withfull moulding the edges etc. complete . Both side polish First Floor

Providing and fixing High density polythein container Syntex or alike one piece moulded water tank made out of low density polythyler and built corrugation including of delivery up to destinationhoisting and fixing of accessories such as inlet, outlet overflow of all tanks capacity above1000 to 20,000 litres First Floor

Providing and fixing High density polythein container Syntex or alike one piece moulded water tank made out of low density polythyler and built corrugation including of delivery up to destinationhoisting and fixing of accessories such as inlet, outlet overflow of all tanks capacity above1000 to 20,000 litres Second Floor

Providing , constructing and fixing 250 millimetre diameter Inspection chamber made up of unplasticized poly vinyl chloride entimetre aterial of thickness 3.5 millimetre and height of 259 millimetre with inlet and outlet of 110 millimetre diameter with 75 millimetre diameter U Trap, Ultra shaft pipe of unplasticized poly vinyl chloride material having height of 470 millimetre and fixingUltra 250 millimetre diameter unplasticized poly vinyl chloride cover and frame in 150 millimetre thick in cement concrete 1:2:4, having crushed sandbed of 100 millimetre thick of size 550 millimetre diameter Including excavation and refilling the sides ofchamber by crushed sand cushioning 150 millimetre thickness, connecting all required unplasticized poly vinyl chloride fittings with rubber lubricant etc. complete. Ground Floor

Providing , constructing and fixing 450 millimetre diameter Inspection chamber made up of Polypropylene / polyethylene material of thickness 3.5 millimetre and height of 388 millimetre with 160 or200 millimetre main inlet (s) outlet and 110 and / or 160 millimetre branch inlets, with 450 millimetre diameter Ultrashaft pipe of HDPE material having height of 460 millimetre , having reinforced cement concrete cover and frame fixingin 150 millimetre thick in c.c.1:2:4, having crushed sand bed of 150 millimetre thick of size 750 millimetre diameter Including excavation and refilling the sides of chamber by sand crushed cushioning 150 millimetre thickness, connecting all required unplasticized poly vinyl chloride fittings with rubber lubricant etc. complete. Ground Floor

Providing , constructing and fixing 600 millimetre diameter Inspection chamber made up of Polypropylene / polyethylene material Having 315 millimetre diameter inlet(s)/outlets and witheccentric reducers as per requirement to connect 160 millimetre and 200 millimetre pipes having thicknessof 5 millimetre and 600 millimetre in height, with inbuilt shaft achieve the invert depth as per sitecondition of wall thickness of 5 millimetre having reinforced cement concrete cover and frame fixing in 150 millimetre thick inc.c.1:2:4, having crushed sand bed of 150 millimetre thick of size 750 millimetre diameter Including excavationand refilling the sides of chamber by sand crushed cushioning 150 millimetre thickness, connectingall required unplasticized poly vinyl chloride fittings with rubber lubricant etc.complete. Ground Floor

Providing and fixing Mandatory/Regulatory sign boards in circular shape of ______ millimetre diameter made out of ____ millimetre aluminum sheet bonded with white retro reflective sheeting of Class B( Type IV High intensity micro-prismatic grade sheeting-HIP) having pressure sensitive/heatactivated adhesive retoreflective specified back ground, border and back side retoreflctivesymbols, letters, numerals, arrow as per IRC:67-2012 Table No 8.3 Supported with backsupport frame 25 millimetre x 25 millimetre x 3 millimetre , duly painted on back side with grey stove enamel paintand supported on one Number of M. S. angle iron post of size 65 millimetre X 65 millimetre X 6 millimetre ,3.45 m long, duly painted with with flat oil paint having alternate black and white bands of25 centimetre width including galvanised iron fixtures etc; fixing the boards in M25 grade concrete block of size60centimetre X 60centimetre X 75centimetre including transportation etc; complete. Class B ( Type IV Highintensity micro-prismatic grade sheeting-HIP) shall have 7 years written warranty from themanufacturer and authorised distributor/convertor issued for field performance including thescreen printed areas and cut-out sheeting and cut-out durable transparent overlay film and thiswarranty certificate in original should be submitted to the Engineer in charge by thecontractor/supplier 600 millimetre diameter made out of 3 millimetre aluminum composite material Ground Floor

Providing Soak pit of size 120 centimetre x 120 centimetre x 120 centimetre including excavating and filling with brick bats.

Providing and laying in trenches 50 millimetre diameter medium grade having embossed as Indian Standard Institute mark galvanised iron pipes of 5.17 kilogramme per metre necessary fitting remaking good thedemolished portion with filling trenches and with primer of anti-corrosive oil paint, 2 coatsIncluding removing existing pipe line if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete. Ground Floor

Providing and laying in trenches 80 millimetre diameter medium grade having embossed as I Indian Standard Institute mark galvanised iron pipes of 8.57 kilogramme per metre necessary fitting remaking good thedemolished portion with filling trenches and with primer of anti-corrosive oil paint, 2 coatsIncluding removing existing pipe line if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete. Ground Floor

Providing and laying in trenches 100 millimetre diameter medium grade having embossed as Indian Standard Institute mark galvanised iron pipes of 12.43 kilogramme per metre necessary fitting remaking good thedemolished portion with filling trenches and with primer of anti-corrosive oil paint , 2 coatsIncluding removing existing pipe line if necessary and conveying and stacking the same in Public Works Department chowky or as directed etc. complete. Ground Floor

Providing and fixing screw down 15 millimetre diameter wheeled stop tap of brass including necessary sockets / union nut complete Ground Floor

Providing and fixing screw down 15 millimetre diameter wheeled stop tap of brass including necessary sockets / union nut complete First Floor

Providing and fixing screw down for 25 millimetre diameter wheeled stop tap of brass including necessary sockets/union nut complete. Ground Floor

Providing and fixing screw down for 25 millimetre diameter wheeled stop tap of brass including necessary sockets/union nut complete. First Floor

Providing and fixing screw down for 32 millimetre diameter wheeled stop tap of brass including necessary sockets /union nut complete. Ground Floor

Providing and fixing screw down for 32 millimetre diameter wheeled stop tap of brass including necessary sockets /union nut complete. First Floor

Providing and fixing screw down for 40 millimetre diameter wheeled stop tap of brass includingnecessary sockets /union nut complete. Ground Floor

Providing and fixing screw down for 40 millimetre diameter wheeled stop tap of brass includingnecessary sockets /union nut complete. First Floor

Providing and fixing screw down for 50 millimetre diameter wheeled stop tap of brass includingnecessary sockets/ union nut complete. Ground Floor

Providing and fixing screw down for 50 millimetre diameter wheeled stop tap of brass includingnecessary sockets/ union nut complete. First Floor

Providing and laying concrete pipes of Indian Standard Non-pressure-2 class of 300 millimetre diameter in proper line, leveland slope including necessary collars, excavation, laying, fixing with collars in cement mortar1:1 and refilling the trench complete. Ground Floor

Providing and laying cement concrete pipe of Indian Standard 458:2003 Non-pressure-2 class of 450 millimetre diameter inproper line, level and slope including providing and fixing collars in cement mortar 1:2 andcuring etc. complete. Ground Floor

Providing and laying cement concrete pipe of Indian Standard 458:2003 Non-pressure-2 class of 600 millimetre diameter inproper line, level and slope including providing and fixing collars in cement mortar 1:2 andcuring etc. complete. Ground Floor

Providing and constructing Brick Masonry Inspection Chamber 90 centimetre x 45 centimetre x 90 centimetre including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round glazed stoneware pipes, Brick Masonry, plastering from inside and cast iron lid cover of 75 kilogram with lidand frame fixed in cement concrete. Ground Floor

RWH - Recharge Pit Providing and constructing recharge pit of 2.0m deep and 1.0m dia of pre-cast reinforced cement concrete ringswith 6.5 inch diameter x 25metre deep borewell at the floor of recharge pit including installation ofcombination of solid/perforated poly vinyl chloride casing pipe wrapped around with netlon mesh including 300 millimetre thick sidefilling around outside of reinforced cement concrete rings (annular space) with 40 millimetre sizeboulders including filling of recharge pit up to 0.5 metre depth with 25-75 millimetre clean washedgravels from bottom up followed by 0.5m depth of 10-25 millimetre of clean washed stones followedby 0.5 metre of washed river fine aggregate (natural sand/crushed sand Vertical shaft impact (VSI) grade finely washedetc.) including netlon mesh between each gravel/fine aggregate (natural sand/crushed sand Vertical shaft impact (VSI) grade finely washed etc.) media layer including covering with reinforced cement concrete slab, manhole frameand cover, poly vinyl chloride rungs, poly vinyl chloride end-caps, fittings etc. including arrangement for inlet and outlet pipeexcavation and backfilling as shown in the drawing.The rate shall be inclusive of all labour,material, wastage, scaffolding, transportation, taxes, including all leads, lifts at all levels. Allmaterial should be of approved make. All works complete as per the drawing, technicalspecification and direction of the Engineer in charge. Ground Floor

Providing expansion joints in reinforced cement concrete framed structure (exterior column) with plain premoulded filler 25 millimetre thick with 75 millimetre wide and 1 millimetre thick stainless steel plate andfinishing etc. complete.Ground Floor

Providing and installing bio digester unit based on DRDO technology made of fibre reinforced plastic (FRP) having composition and following technical specifications and including necessary pipe and accessories up to 3 meter length, excluding the necessary excavation for installing the bio digester.Percentage of fibre glass (glass content in fibre glass should be minimum 30 Percent ): -33.33 Percent Percentage of polyester resin: - 66.67 Percent Water absorption (as per ASTM):-0.30 Percent Fla millimetre ability as per ASTMTensile strength:-115 MPASpecific Gravity at 25 degree centigrade 1.45Izod impact strength:-65KJ/M2Heat defection/distort temperature:-65deg C Corrosion resistance (Non Corrosive) fitted with Inlet pipe size rigid poly vinyl chloride : -100 millimetre Outlet pipe size rigid poly vinyl chloride :-80 millimetre Gas outlet rigid poly vinyl chloride with Valve: 20 millimetre Bacteria i millimetre obilization poly vinyl chloride mattes (on all partition)With DRDO TOT licensee and latest batch certificate(month and year of supply) and capacity as below - k)Upto 400 user size (5 metre x 2.0 metre x 1.5 metre), Capacity of Biodigester:-15000 liters, Area of top , bottom and side walls :- 41.00 sq.m, Area of partition walls : 12.00 square metre. Total weight of FRP :-678.80 Kilogram, Bacteriainoculums quantity:-5200 liters, Minimum thickness of sidewalls/ top and bottom: 8 millimetre , Number of inside partitions:- 4, Minimum thickness of partition wall: 4 millimetre Ground Floor

Providing and fixing screw down for 80 millimetre diameter wheeled stop tap of brass includingnecessary sockets /union nut complete. Ground Floor

Providing and fixing screw down for 80 millimetre diameter wheeled stop tap of brass includingnecessary sockets /union nut complete. First Floor

Providing and fixing white Opal series European type wall-hung, of size 400 millimetre x 370 millimetre x 575 millimetre with approved make flush valve including soil pipe, vent pipe uptooutside face of wall, 100 millimetre dia cast iron plug bend inlet pipe all fittings, cutting and making goodwalls, floors etc as directed by Engineer in charge. Ground Floor

Providing and fixing white Opal series European type wall-hung, of size 400 millimetre x 370 millimetre x 575 millimetre with approved make flush valve including soil pipe, vent pipe uptooutside face of wall, 100 millimetre dia cast iron plug bend inlet pipe all fittings, cutting and making goodwalls, floors etc as directed by Engineer in charge. First Floor

Providing and laying Cast in situ/ Ready Mix cement concrete Mix-20 of trap metal for Reinforced Cement Concrete Chajja as per detailed design and drawings including centering, formwork, cover blocks compacting , curing , finishing and roughening the surface if special finish is to be provided and curing complete (Excluding reinforcement and structural steel), with fully automatic micro processor based Progra millimetre able Logic Controller with Supervisory Control and Data Acquisitionenabled Reversible drum type concrete mixer/ concrete Batch Mix plant (Pan mixer) etc. complete, with fine aggregate (Natural Sand/ Crushed Sand Vertical shaft impact (VSI) Grade finely washed etc.) Ground Floor

Providing and laying Cast in situ/ Ready Mix cement concrete Mix-20 of trap metal for Reinforced Cement Concrete Chajja as per detailed design and drawings including centering, formwork, cover blocks compacting , curing , finishing and roughening the surface if special finish is to be provided and curing complete (Excluding reinforcement and structural steel), with fully automatic micro processor based Progra millimetre able Logic Controller with Supervisory Control and Data Acquisitionenabled Reversible drum type concrete mixer/ concrete Batch Mix plant (Pan mixer) etc. complete, with fine aggregate (Natural Sand/ Crushed Sand Vertical shaft impact (VSI) Grade finely washed etc.) First Floor

Providing and laying Cast in situ/ Ready Mix cement concrete Mix-20 of trap metal for Reinforced Cement Concrete Chajja as per detailed design and drawings including centering, formwork, cover blocks compacting , curing , finishing and roughening the surface if special finish is to be provided and curing complete (Excluding reinforcement and structural steel), with fully automatic micro processor based Progra millimetre able Logic Controller with Supervisory Control and Data Acquisitionenabled Reversible drum type concrete mixer/ concrete Batch Mix plant (Pan mixer) etc. complete, with fine aggregate (Natural Sand/ Crushed Sand Vertical shaft impact (VSI) Grade finely washed etc.) Second Floor

Providing uncoursed rubble masonary of trap stone in cement mortar 1:3 in basement with patent water proofing compound added to it at 1 kilogramme per bag of cement including bailing out water manually, scaffolding racking out joints when plastering is to be done and watering complete. Ground Floor

Providing fly ash brick masonry with conventional/ Indian Standard type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete Ground Floor

Providing and applying two coats of water proof cement paint of approved manufacture and of approved colour to the plastered surfaces including scaffolding if necessary, cleaning and preparing the surface, watering for two days etc. complete. Ground Floor

Providing patti/ band 150 milimetre wide on plastered surface 12 milimetre to 15 milimetre thick in cement mortar 1:3 line and level including neat finishing scaffolding curing etc. complete. Ground Floor

Providing and erecting 'Y' type barbedd wire fencing with seven rows of wire with 2.45 milimetre diameter galvanised iron pipe (Rezan / concentina wire 0.75 milimetre diameter) with hot dip and galvanised iron coated hooks as per drawing supported on mild steel angle 50 x 50 x 6 milimetre at 2.50 metre centre to centre including fixing and fastening with wire, painting mild steel angles with one coat of red lead primer and two coat of oil paint complete. Ground Floor

Providing and fixing bituminous pad 25 millimetre thick for expansion joints in retaining wall, compound wall etc. complete Ground Floor

Providing and fixing mild steel grill gate with angle iron frame 65 millimetre x 65 millimetre x 10 millimetre with iron bars at 150 millimetre centre to centre and diagonal flats as per the detailed drawing including hinges, pivot block locking arrangement, welding riveting and oil painting of three coats of approved shade Weight of gate 35 Kg/Smt. Ground Floor

ELECTRICAL WORK EST 1 Supplying and erecting HMS P.V.C. conduit 25 mm. dia. with necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC.

Supplying and laying HMS PVC conduit 25 mm dia with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC.

Supplying and erecting HMS P.V.C. conduit 32 mm. dia. with necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC.

Supplying and erecting green colour earthing with 1x 1.5 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG- MA/BW

Supplying and erecting mains with 2x2.5 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW ( for computer pt and MCB to SB= 100x15, and 228x15= 4920

Supplying and erecting green colour earthing with 1x 2.5 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Supplying and erecting mains with 2x4 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW ( for AC and PP 287x10 mtr= 2870

Supplying and erecting mains with 2x6 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW ( from meter room to each shop )

Supplying and erecting ISI mark modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete.

Supplying and erecting ISI mark modular type switch 16A duly erected on provided plate and box with wiring connections complete.

Supplying and erecting ISI mark modular type 3 pin 6A multi sockets with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting ISI mark modular type 3 pin 6 / 16A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting ISI mark modular type T.V. socket single outlet, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting ISI marked modular type telephone socket one gang with safety shutter, duly erected on provided plate and box with wiring connections complete

Supplying and erecting ISI mark modular type (two module) electronic step regulator for fan, duly erected on provided plate and box with wiring connections complete. Note: Add Rs 57/- for additional two module box with double mounting plate if required

Supplying and erecting ISI mark modular type blanking plate one module, duly erected on provided plate & box.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 1 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background..

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 3 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 12 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Point wiring for light/fan/bell concealed type in min 20 mm ISI marked HMS PVC conduit with 1.5 sq.mm. (2+1E) FR grade copper wires, modular type switch, earthing and required accessories as per specification No: WG-PW/CW

Wiring for plug on board with Switch socket concealed type, copper wiring and earthing and with modular accessories as per specification No: WG-PW/CW

Point wiring for light/fan/bell hybrid type (Surface type under false ceiling and concealed type for drops & switch boards on walls) in min 20 mm PVC conduit / casing n capping with 1.5 sq.mm. (2+1E) FR grade copper wires, modular type switch, earthing and required accessories as per specification No: WG- PW/HW

Supplying and erecting telephone copper cable 2 pair with 0.5 mm dia. laid in provided PVC casing capping/ conduit as per specification No. WG-TW

Supplying and installing co-axial copper cable low voltage grade RG-6 as per specification No. WG-TW

Supplying and erecting LED square / circular 5 to 8W down lighter having pressure die-cast aluminium housing, opal translucent cover, mounting arrangement with board for surface type or spring loaded mounting clips for flush type complete.

Supplying and erecting LED square / circular 9 to 12W down lighter having pressure die-cast aluminium housing, opal translucent cover, mounting arrangement with board for surface type or spring loaded mounting clips for flush type complete.

Supplying and erecting LED square / circular 13 to 15W down lighter having pressure die-cast aluminum housing, opal translucent cover, mounting arrangement with board for surface type or spring loaded mounting clips for flush type complete.

Supplying and erecting square shaped CRCA /die-cast aluminium powder coated housing LED panel light (slim edge-lit) suitable for 9 W - 12 W with provision for plane front frame with translucent cover fixed to the housing complete.

Supplying and erecting square / round shaped CRCA /die-cast aluminium powder coated housing LED panel ( slim edge-lit) light suitable for 13W to18W with provision for plane front frame with translucent cover fixed to the housing complete.

Supplying and erecting CRCA /die-cast aluminium powder coated housing LED panel light (slim edge-lit) square / round shape suitable for 19 to 24 W with provision for plane front frame with translucent cover fixed to the housing complete.

Supplying and erecting square shaped CRCA /die-cast aluminium powder coated housing LED panel light (slim edge-lit) 600x600mm suitable for 36 W-40W with provision for plane front frame with translucent cover fixed to the housing complete.

Supplying and erecting rectangular shaped CRCA /die-cast aluminium powder coated housing LED panel (slim edge-lit) 300x1200mm of suitable for 36 to 40 W with provision for plane front frame with translucent cover fixed to the housing complete.

Supplying LED concealed type foot / step light with aluminium body for indoor/outdoor application suitable for upto 4W-6W LED including driver and erecting by making necessary arrangement/recess in wall to make it flush with surface.

Supplying and erecting LED 20W tube light fitting (4 feet) with aluminium housing, heat sink, integrated HF electronic driver complete.

Supplying and erecting LED Mirror Light with integrated driver including 14W to 18W lamp with polycarbonate housing and opal diffuser to be fixed above mirror or as required on clamps complete.

Supplying and erecting ding dong / electronic musical type call bell with heavy duty coil suitable to operate on 230V A.C. supply erected on polished double wooden block/sunmica block of suitable size

Supplying and erecting 10-12W, 230V integral type LED Lamp suitable for B-22/E-27 base.

Supplying and erecting fresh air cum exhaust fan of light duty250 V A.C. 50 cycles 225mm. 1400 RPM rust proof body & blades, wire mesh, duly erected in an approved manner.

Supplying and erecting five star rated energy saving Ceiling fan 230 V A.C. 50 cycles 1200 mm complete erected in position as per specification no. FG-FN/CF

Supplying and erecting fan hook box of 10 mm M.S. round bar bounded to the R.C.C. bars upto 50 mm length each side and pierced through a 16 S.W.G. thick aluminium/M.S. Bowl 100 mm dia.or equivalent square size and having depth upto 75 mm complete erected with duly painted by one coat of red oxide paint and two coats of paint erected in position and without any leakage of slurry of cement concrete on either side of the box and positioned to the bottom level of the slab.

Supplying and erecting ‘B’ grade G.I. pipe / M.S. pipe down rod duly painted for fan complete erected with PVC three core flexible cable 1 sq. mm copper PVC wire.

Supplying, erecting and marking SPMCB 6A to 32A, C-series (for motor/power) in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting and marking SPMCB 6A to 32A, B- series (for lighting) in provided distribution board as per specification no. SW- SWR/MCB

Supplying, erecting and marking DPMCB 6 A to 32 A B- series (for lighting) in provided distribution board as per specification no. SW- SWR/MCB

Supplying, erecting and marking TPMCB 40A to 63A in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting and marking FPMCB 40A to 63A in provided distribution board as per specification no. SW-SWR/MCB

Supplying and erecting triple pole and neutral distribution board (TPNDB) with door surface/ flush mounted SP / TP MCBs of 12 ways, on iron/ GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB

Supplying and erecting single pole and neutral distribution board (SPNDB) with door surface/flush mounted with 2 ways for incoming and 10 ways for outgoing SP MCB’s on iron/ GI frame as per specification no. SW-SWR/MCBDB

Supplying and erecting CRCA sheet metal one way enclosures suitable for DP MCB /TP MCB /FP MCB erected on angle iron/GI frame complete.

Supplying and erecting triple pole and neutral distribution board (TPNDB) with door surface/ flush mounted suitable for 3 pole MCCB as incomer & outgoing SP MCB (12 poles) or TP MCB of 4 ways (12 poles) on iron/ GI frame. (vertical busbar type) as per specification no. SW-SWR/MCBDB1

Providing and erecting 4 Pole MCCB upto 100A, 415V, with short circuit rating 25 kA (Ics=100% of Icu ),adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/ UV/ trip alarm contact and MCCB should have phase barriers both sides, in provided enclosure on iron /GI frame as per specification no. SW-SWR/MCCB

Providing and erecting 3 Pole MCCB upto 100A, 415V, with short circuit rating 25 kA (Ics=100% of Icu ),adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/ UV/ trip alarm contact and MCCB should have phase barriers both sides, in provided enclosure on iron /GI frame as per specification no. SW-SWR/MCCB

Providing and erecting 4 Pole MCCB of 250A,415V capacity with short circuit rating 36 kA (Ics=100% of Icu) adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/ UV/ trip alarm contact and MCCB should have phase barriers both sides, in provided enclosure on iron /GI frame as per specification no. SW-SWR/MCCB

Providing and erecting 4 Pole MCCB of 315/400A, 415V capacity with short circuit rating 36 kA (Ics=100% of Icu), adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/ UV/ trip alarm contact and MCCB should have phase barriers both sides, in provided enclosure on iron /GI frame as per specification no. SW-SWR/MCCB

Providing and erecting floor / wall mounting, MCCB panel board with door suitable for four pole incoming 250A, 4 ways four pole outgoing upto 100 A MCCB's on iron frame, as per specification no SW-SWR/MCCBPB. (Excluding MCCB'S)

Providing and erecting floor / wall mounting, MCCB panel board with door suitable for four pole incoming 400A, 8 ways four pole outgoing upto 100 A MCCB's on iron frame, as per specification no SW-SWR/MCCBPB. (Excluding MCCB'S)

Providing and erecting incoming and outgoing cable alleys suitable for MCCB panel board with door of 250A incoming and 4 way outgoing or 400A incoming and 2 way outgoing made from CRCA sheet 1.6 mm thick duly powder coated and having vertical insulated partition for shielding between the shared face of cableway and DB complete.

Providing and erecting incoming and outgoing cable alleys suitable for MCCB panel board with door of 250A incoming and 12 way outgoing or 400A incoming and 6/8 way outgoing made from CRCA sheet 1.6 mm thick duly powder coated and having vertical insulated partition for shielding between the shared face of cableway and DB complete.

Providing and erecting prewired meter module suitable for MCCB panel board with CT's and emf's VIF meter complete.

Supplying and erecting marine plywood 18/19 mm thick fixed to wall or on provided panel board with necessary materials such as screws, wall fasteners, supports, nut bolts etc. complete.

Supplying, erecting & terminating XLPE armoured cable 4 core 25 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Providing earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm with funnel with a wire mesh for watering and brick masonry block C.l. cover complete with all materials, testing & recording the results as per specification no. EA-EP

Supplying and erecting GI strip of required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint in an approved manner with joints required. As per specification no EA-EP.

EST 2 Supplying and erecting PVC insulated PVC round sheathed 1.5 sq.mm (30 no. x 0.25 mm dia.) 3 core flexible multi stranded copper Industrial cable for voltage grade up to 1.1 kV ( 38 pole x 9 mtr= 342m and high mast 16x8= 128

Supplying and erecting LED street light fitting 100W, including lamp, with PF > 0.95 class IP 65 and above housing of pressure die cast aluminium alloy and heat sink extruded aluminium complete per specification No FG-ODF/FLS-2.

Supplying and erecting LED Flood light fitting of 200W, including lamp, with PF > 0.95,class IP 65 and above Housing of pressure die cast aluminium alloy and heat sink extruded aluminium complete per specification No FG-ODF/FLS-2

Supplying, erecting and marking SPMCB 6A to 32A, B- series (for lighting) in provided distribution board as per specification no. SW- SWR/MCB

Supplying, erecting & terminating XLPE armoured cable 4 core 10 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 75 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete.

Supplying and erecting 16 m (clear height) High Mast (Top-150mm, Bottom- 360mm) with lowering and raising motorized unit, lantern carriage assembly suitable for max. 8 nos. luminaries and its control gear box, lightning finial arrangement for fixing aviation light and foundation bolts on provided foundation as per specification no. OH-PL/HM (excluding luminaries).

Providing and erecting 9 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 155 mm A/F, top 70 mm A/F on provided foundation as per specification no. OH- PL/OPL

Providing and erecting galvanised 1000mm single arm sword type bracket with FRP dome and ball as per specification no. OH- PL/PBKT

Supplying and erecting outdoor stand mounted feeder pillar for highmast of the same manufacturer with 32A TPN MCB incomer, single dial timer switch, 25A TP contactor for automatic switching of luminaries, 2 nos 9A contactors and raise/lower push button, and provision for termination of adequate size of incoming and outgoing cables erected in min. 14 SWG CRCA sheet box with supporting angles, self-lock, gasket and slanting top erected with CC foundation complete.

Providing earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm complete with all materials, testing & recording the results as per specification no. EA-EP

Providing pipe type earthing with 40mm. dia. G.l. pipe or 20 mm dia. G.l. Rod complete with all materials as per specification no. EA- EP

Making M- 20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity at site as 10 T/sq.m at 1.5 m depth including supply of steel, concrete, excavation and fixing provided nut bolts with the help of template, duly plastered as per design complete (for 9m & 10m high octagonal /conical GI pole).

Making M- 20 cement concrete foundation by considering the safe soil bearing capacity at site as 10 T/sq. m at 2 m depth including excavation and fixing provided nut bolts with the help of template, duly plastered as per design complete (for 16 m raising lowering high mast).

EST 3 Supplying, installing, testing and commissioning of split type variable speed inverter technology room Air conditioning unit 2 TR capacity having ISEER minimum 4.50 suitable to operate on 250V, 50 cycles, A.C. supply having 1 no. of air handling unit hi-wall/ floor mounting type complete with Refrigerants R410 A /R32 and copper condenser at position. specification no. APAC/ SAC

Supplying and erecting soft drawn copper pipe suitable for refrigeration system having 22 SWG thickness and inner dia / size 12 mm complete

Supplying and erecting soft drawn copper pipe suitable for refrigeration system having 22 SWG thickness and inner dia / size 16 mm complete.

Supplying, installing, testing and commissioning of cassette type variable speed inverter technology split room airconditioning unit 2 TR capacity having ISEER minimum 3.50 to maximum 3.99 suitable to operate on 230/250 V, 50 cycles, AC supply having 1 no. air handling unit false ceiling mounting type complete with refrigerant R32/R410A and copper condenser coil at position as per specification with provided copper piping and drainage pipe.

Supplying, installing, testing and commissioning of cassette type variable speed inverter technology split room air conditioning unit 3 TR capacity having ISEER maximum 4.50, suitable to operate on 230V /415 V, 50 cycles, AC supply having 1 no. air handling unit false ceiling mounting type complete with refrigerant R32/R410A & copper condenser coil at position with provided copper piping and drainage pipe.

Supplying, erecting, testing and commissioning of self contained water cooler 230/250 Volts 50 cycles nominal cooling capacity of 150 liters/hr and storage capacity 150 liters with partially stainless steel body complete. specification no. AP-WCR/WC

Supplying and erecting ultra voilet storage type water purifier (RO+UV+UF) with softener for safe drinking water consisting of UV germicidal tube of 8W capacity choke made of copper wire and two indicator lamps, storage capacity of purified water 7 to 8 litre with activated carbon filter and softener operating on 230V single phase AC supply.

Carrying out core cutting of size 3" to 5" dia x 15" length in the C.C./rock/stone wall with the help of specialized core cutting machine in proper manner and finishing the site as original.

Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for over coating and insulating on provided PC / copper pipes having 9 mm thickness and inner diameter / sizes 12 mm for solar water heater system.

Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for over coating and insulating on provided PC / copper pipes having 9 mm thickness and inner diameter / sizes 16 mm for solar water heater system.

Supplying and erecting iron, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority.

EST 4 Supplying and erecting HMS P.V.C. conduit 25 mm. dia. with necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC.

Supplying and laying HMS PVC conduit 25 mm dia with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC.

Carrying out core cutting of size 3" to 5" dia x 15" length in the C.C./rock/stone wall with the help of specialized core cutting machine in proper manner and finishing the site as original.

Supplying and erecting iron, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority.

Supplying, erecting & terminating XLPE armoured cable 3 core 4 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating XLPE armoured cable 3 core 16 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating XLPE armoured cable 3½ core 95 sq. mm. aluminium conductor with continuous 8.35 sq. mm. (10 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating XLPE armoured cable 3½ core 120 sq. mm. aluminium conductor with continuous 12.97 sq. mm. (8 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 90 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete.

Providing and erecting Hot dipped galvanized ladder type cable tray manufactured from 16 swg (1.6 mm thick) GI sheet of 150 mm width & 100 mm height comprising all required standard accessories.

Providing Round bottom fire bucket of 9 Litres capacity as per IS : 2546 made out of 24 gauge G.I. sheet with extra handle at bottom duly painted white inside and red outside with FIRE Mark, on provided stand/ wall hook complete.

Providing Floor mounting stand for keeping 4 Nos. of FIRE buckets 1500mm in length, 900mm in height frame made out of 30x30x4 mm angle iron with cross supports for legs, welded with 4 hooks and duly painted with one coat of red lead and two coats of silver paint complete.

Supplying and erecting Carbon Dioxide (CO2) fire extinguisher of 4.5 kg. capacity cartridge type conform to IS 2878 /15683 complete erected with necessary clamp made from 50 x 6 mm. M. S. flat with nut & bolts grouted in wall complete.

Supplying and erecting ABC powder type fire extinguisher as per IS : 13849 /15683 of 6 kg capacity with necessary clamp for erection on wall.

Supplying and erecting D.O.L. Starter 400V. 3 phase, 50 cycles with no volt coil and overload element with necessary materials and connected to supply upto 7.5 H.P.

Supplying, installing, testing and commissioning of with perfect aligning, proper levelling of fire service main single stage pump, of 2400 LPM at 76 m head centrifugal type, 75 HP (55 kW) 3 phase, 415 volt, 50Hz or of suitable HP complete as per specification no. FF-MFP/SSC

Supplying, installing, testing and commissioning of with perfect aligning, proper levelling of jockey pump of 240 LPM at 105 m head 20 HP (15 kW), 3 phase, 415 volt, 50Hz or of suitable HP with suitable stages as per specification no. FF-MFP/JP

Supplying, installing, testing and commissioning of with perfect aligning, proper levelling of booster pump of 450 LPM at 35 m head 7.5 HP (5.5 KW), 3 phase, 415 volt, 50Hz or of suitable HP with suitable stages as per specification no. FF-MFP/BP

Supplying and erecting G.I. pipe above ground of ‘C’ class ERW of size 75/80 mm dia with necessary fittings complete as per specification no. FF-PP

Supplying and erecting G.I. pipe above ground of ‘C’ class ERW of size 100 mm dia with necessary fittings complete as per specification no. FF-PP

Supplying and erecting G.I. pipe above ground of ‘C’ class ERW of size 150 mm dia with necessary fittings complete as per specification no. FF-PP

Supplying and erecting G.I. pipe above ground of ‘C’ class ERW of size 200 mm dia with necessary fittings complete as per specification no. FF-PP

Supplying and erecting cast iron foot valve ball type/flap type of size 100 mm dia with strainer for negative suction complete as per specification no. FF-VL/FV

Supplying and erecting cast iron foot valve ball type/flap type of size 150 mm dia with strainer for negative suction complete as per specification no. FF-VL/FV

Supplying and erecting 100 mm dia end line strainer for positive suction complete as per specification no. FF-VL/ELS

Supplying and erecting 150 mm dia end line strainer for positive suction complete as per specification no. FF-VL/ELS

Supplying and erecting cast iron double flange butterfly valve of size 100 mm dia. complete as per specification no. FF-VL/BFV

Supplying and erecting cast iron double flange butterfly valve of size 150 mm dia. complete as per specification no. FF-VL/BFV

Supplying and erecting cast iron double flange butterfly valve of size 200 mm dia. complete as per specification no. FF-VL/BFV

Supplying and erecting cast iron double flange NRV of size 100 mm dia complete as per specification no. FF-VL/NRV

Supplying and erecting cast iron double flange NRV of size 150 mm dia complete as per specification no. FF-VL/NRV

Supplying and erecting cast iron double flange NRV of size 200 mm dia complete as per specification no. FF-VL/NRV

Supplying and erecting gun metal single outlet hydrant valve fitted with necessary accessories complete as per specification no. FF-VL/HV

Supplying and installing one piece moulded HDPE / fibre water tank for negative suction only, having capacity 1000 litres fitted with necessary accessories complete as per specification no. FF-FFA/PT

Supplying and installing wall mounting swinging Hose reel drum fitted with 19 mm dia. 30m long high pressure polypropylene (Polyhose) fitted with necessary accessories complete as per specification no. FF-FFA/HV

Supplying fire fighting reinforced rubber lined (R.R.L.) hose pipe, 63mm dia, 15m in length, fitted with necessary accessories complete as per specification no. FF-FFA/RRL

Supplying and erecting gun metal branch pipe of 63 mm dia fitted with 20 mm dia detachable hexagonal nozzle complete as per specification no. FF-FFA/NZ

Supplying and erecting fire brigade header of 150 mm dia, for supplying water in fire tank complete as per specification no. FF- FA/FBC

Supplying and erecting fire brigade header (Siamese connection) of 150 mm dia for supplying water to wet riser system complete as per specification no. FF-FFA/SMC

Supplying and installing air vessel of 300 mm dia 1.5m in height M.S. tank installed inside pump house / on terrace complete as per specification no. FF-FFA/ACT

Supplying and erecting 20/25mm dia gun metal air release cock, with necessary G.I. coupling to be fitted on top of air vessel or on wet riser complete as per specification no. FF-FFA/ARV

Supplying and installing pressure gauge of 100 mm dia., 0-300 PSI or 0-14 kg per cm square fitted with 12/15 mm dia. pad cock valve, and G.I. pipe, elbow etc. complete as per specification no. FF- FFA/PG

Supplying and installing pressure switch with 12/15 mm dia isolation valve, G.I. nipple, elbow, etc complete as per specification no. FF-FFA/PS

Supplying and erecting M.S./CRCA cabinet for housing single hydrant valve (size 400 x 400 x 400mm.) made from 16 SWG sheet and angle iron 25 mm. x 25 mm. x 4 mm. having front doors with viewing glass (8"x6") and locking arrangement with necessary fixing material such as rubber bidding etc. duly painted in post box red colour.

Supplying and erecting M.S./CRCA cabinet for housing Fire Brigade / SIEMESE connections (size 1250 x 400 x 300 mm.) made from 16 SWG sheet and angle iron 25 mm. x 25 mm. x 4 mm. having front doors with viewing glass (8" x 6") and locking arrangement with necessary fixing material such as rubber bidding etc. duly painted in post box red colour.

Supplying, installing, testing and commissioning of heat detector complete on box as per specification no. FF-FAS/HD

Supplying, installing, testing and commissioning of optical type smoke detector complete on box as per specification no. FF- FAS/SD

Supplying, installing, testing and commissioning of manual call point (Pill box) with break glass push button in metal enclosure complete as per specification no. FF-FAAS/MCP

Supplying, installing, testing and commissioning of hooters with CRCA enclosure complete as per specification no. FF-FAAS/HTR

Supplying, installing, testing and commissioning of FRLS, XLPE armoured cable 2 core 1.5 sq.mm. copper conductor complete erected on wall/ ceiling complete as per specification no. CB- LT/CU

Supplying, installing, testing and commissioning of 12 Zones Microprocessor based conventional fire alarm control panel (FACP) with standard accessories complete as per specification no. FF-FAAS/FACP

FIRE FIGHTING PUMP PANEL INCOMER SPD TYPE-2 1No.300A 4P MCCB (25 KA) ,MICROPROCESSOR BASED METERING & INDICATION 1 set of phase indicating lamps 1 set of Voltmeter (0-500V) with Built-in VSS with 3 nos. 2A SP MCB 1 set Ammeter (0-400A) with ASS and 3 nos.300/5A, CT's BUS-BAR 1 Set of 300A TPN Aluminium Bus Bar with colour coded PVC Sleeves OUTGOINGS 2 Nos. 160A TPMCCB (25 KA) 2 No. 63A TP MCCB (25 KA) 1No. 63A TP MCCB (25 KA) SPARE 2 Nos. of S/D starter with self illuminated Push button for ON & OFF and suitable rating of contactor and O/L relays, suitable for 75 HP Pump 1 Nos. of S/D starter with self illuminated Push button for ON & OFF and suitable rating of contactor and O/L relays, suitable for 12.5 HP Pump 2 Nos. of S/D starter with self illuminated Push button for ON & OFF and suitable rating of contactor and O/L relays, suitable for 5 HP Pump NOTE : The starters of Fire Fighting Pump shall be interlocked with the Pressure switch.

EST 5 Supplying and laying HMS PVC conduit 20 mm dia. with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC.

Supply Installation commissioning of 4 MP Full HD IP Dome Camera- VIDEO COMPRESSION - H.265+/H.265/H.264+/H.264,VIDEO Resolution - 2688 x 1520 resolution, Frame Rate – Upto 25-30fps, Image Sensor - 1/3" 4 MP progressive scan imager, Lens Type – Fixed Focal, Zoom Lens - 2.8 mm, F2.0, Minimum illumination - 0.08 lux colour @ F2.0 (Colour, 1/3s, 30 IRE) , 0 lux B/W with IR LEDs on @ F2.0, Image Setting – Compression, Color, brightnrdd, sharpness, contrast, white balance, exposure control, backlight compensation, Protocol - IPv4/v6, TCP/IP, UDP, RTP, RTSP, RTCP, HTTP, HTTPS, SSL, FTP, SMTP, DHCP, PPPoE, UPnP, SNMP v2/v3, Bonjour, DNS, DDNS, IEEE 802.1X, QoS, NTP Security - User account and password protection, HTTPS, IP filter, IEEE 802.1X, digest authentication, user access log, TLS1.2, AES-256, SSH/Telnet closed, FTP disable Operating Conditions - –30°C to 60°C Casing /Housing - INGRESS PROTECTION IP66, IMPACT RESISTANCE-IK10 Smillar to make sony, Axis, honeywell Three Year Warranty

Supplying and erecting PVC Surface modular switch box with double mounting plate for 4 modules duly erected.

Supply Installation commissioning of 4 MP Full HD IP Bullet Camera- VIDEO COMPRESSION - H.265+/H.265/H.264+/H.264,VIDEO Resolution - 2688 x 1520 resolution,Frame Rate – Upto 25-30fps,Image Sensor - 1/3" 4 MP progressive scan imager,Lens Type – Fixed Focal,Zoom Lens - 2.8 mm, F2.0, Minimum illumination - 0.08 lux colour @ F2.0 (Colour, 1/3s, 30 IRE) , 0 lux B/W with IR LEDs on @ F2.0, Image Setting – Compression, Color, brightnrdd, sharpness, contrast, white balance, exposure control, backlight compensation,Protocol - IPv4/v6, TCP/IP, UDP, RTP, RTSP, RTCP, HTTP, HTTPS, SSL, FTP, SMTP, DHCP, PPPoE, UPnP, SNMP v2/v3, Bonjour, DNS, DDNS, IEEE 802.1X, QoS, NTP,Security - User account and password protection, HTTPS, IP filter, IEEE 802.1X, digest authentication, user access log, TLS1.2, AES-256, SSH/Telnet closed, FTP disable Operating Conditions - –30°C to 60°C Casing /Housing - INGRESS PROTECTION IP66, IMPACT RESISTANCE-IK10 Smillar to make sony, Axis, honeywell Three Year Warranty

Supplying and installing UTP networking cat-6 cable suitable for LAN / WAN Computer net-working as per specification No. WG-COC/NC

Supply Installation testing and commissioning of PTZ Network Camera - VIDEO COMPRESSION - H.265 / H.264 / MJPEG VIDEO Resolution - 1920 × 1080 (1080p) Frame Rate – Primary Stream: 1080p/720p @ 60/50 fps 2nd Stream: D1/CIF @ 30/25 fps 3rd Stream: 720p/D1/CIF @ 30/25 fps, Image Sensor - 1/2.8" Exmor CMOS, Lens Type – PTZ, Zoom Lens - 4.8 mm – 120 mm, Minimum illumination - 0.005 lux (color)/0 lux (B/W) @ F1.6 (with IR LEDs on), Panning Range - 360° degrees endless, Tilting Range- –15° to 90° degrees , auto flip 180° degrees, Image Setting – Compression, Color, brightnrdd, sharpness, contrast, white balance, exposure control, backlight compensation Audio- AUDIO IN/OUT 1 / 1 Protocol - IPv4/v6, TCP/IP, UDP, RTP, RTSP, HTTP, HTTPS, SSL, FTP, SMTP, DHCP, PPPoE, UPnP, SNMP, Bonjour, DDNS, IEEE 802.1x, QoS, NTP, IP Filter, ONVIF, Security - User account and password protection, HTTPS, IP Filter, IEEE 802.1x, Digest authentication, User access log, Hardware security chipset protection,Operating Conditions - –40°C to 70°C (–40°F to 158°F ) Casing /Housing – Aluminum INGRESS PROTECTION IP66, Smillar to make sony, Axis, honeywell Three Year Warranty

Supply Installation commissioning of 4K Embedded Network Video Recorder 32 Channels- MAIN PROCESSOR- Quad-core embedded processor, OPERATING SYSTEM -Embedded LINUX, AUDIO INPUT-1 Channel ,OUTPUT -1 Channel Output RCA , INTERFACE- 2 HDMI , 1 VGA , RESOLUTION - 3840 × 2160, OSD - Camera title; Time; Video loss; Camera lock; Motion detection; Recording, COMPRESSION- H.265/H.264/MJPEG/MPEG4, RECORD BIT RATE- 320 Mbps, RECORDING MODE -Schedule Regular/Continuous, Motion Detection, Alarm, Manual; Stop, TRIGGER EVENTS- Recording; PTZ; Tour; Alarm; Video Push; Email; FTP; Snapshot; Buzzer, VIDEO DETECTION- Motion Detection, ALARM INPUT, ETHERNET- 1 RJ-45 port (10/100/1000 Mbps), MAXIMUM NUMBER OF USERS -128 users. NETWORK THROUGHPUT -Input 320 Mbps; Output 320 Mbps , SMART PHONE COMPATIBILITY- iPhone; iPad; Android, INTERNAL HDD 4 SATA ports, EXTERNAL HDD- 1 eSATA port, USB PORTS- 3, EMISSIONS -FCC , SAFETY EU: EN 60950-1, UL listed to UL/CSA 60950-1, ROHS compliant ( Three Year Warranty )

Supplying and installing UTP networking cat-6 cable with rodent proof jacket suitable for LAN / WAN Computer net-working as per specification No. WG-COC/NC

Supplying, installing and testing UTP connector (RJ-45) as per specification No. WG-NAS/UTPC

Supplying and fixing 9U wall mount rack (Dimension-DxWxH – 450x550x500 mm) as per specification No. WG-NAS/RAK

Supplying, fixing, and configuring 8-ports managed gigabit switches layer-2, 10/100/1000 base-T PoE smart switch plus 2 SFP only complete.

Supplying and erecting on line UPS pure sine wave of 1 kVA capacity complete with standard features, along with necessary SMF batteries for 30 mins. battery backup, as per specification no. AP-UPS

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 75 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete.

Supply installation and commissioning of 42” Full HD Commercial LED Display /Monitor 42 inches or higher Full HD VGA DVI HDMI LAN USB RGB RS 232C IN/OUT AV IN COMPONENT IN AUDIO IN/OUT WIFI READY SPEAKERS( Sony / Samsung / Panasonic ) ( Three Year Warranty )

Supplying, fixing, and configuring web smart power over ethernet switch of 24 ports on provided rack or as directed as per specification No. WG-NWC/ENS

Providing and erecting 5 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 130 mm A/F, top 70 mm A/F on provided foundation as per specification no. OH- PL/OPL.

Making M- 20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity as 10 T/sq.m at 1.5 m depth including supply of steel, concrete, excavation, fixing provided nut bolts with the help of template, duly plastered as per design complete (for 3 to 5m octagonal / conical GI pole).

Supply Erecting Testing and Commissioning of 4TB HDD survillance ciard disk oduct Dimensions 10.2x2.5x15.2 cm item mode numbers ST4000VX007 Memory storage capacity 4 TB flash memory Installed size 4 TB, Digital storage capacity 4TB, hard Drive Rotation speed 5900RPM Surveillance DVRs ,Hardware Interface SATA 6.0 gB/S Graphics Card Interface PCI-E,Compatible Devices Desktop Buffer size64 MB.

EST 6 Supplying, installing, testing and commissioning of 50 kWp capacity on grid solar power pack with GI mounting structure and inter connecting wires / cables without battery bank SPV modules and solar power conditioning unit of required capacity complete, with 5 years on site performance warrantee. Specification no. ESD-RT- ONG (add 36190 per KWp after 11 KWp 50-11=39 KWp x 36190=1411410 +3,98,096= 18,09,506)

Providing and erecting 4 Pole MCCB upto 100A, 415V, with short circuit rating 25 kA (Ics=100% of Icu ),adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/ UV/ trip alarm contact and MCCB should have phase barriers both sides, in provided enclosure on iron /GI frame as per specification no. SW-SWR/MCCB

Providing and erecting floor / wall mounting, MCCB panel board with door suitable for four pole incoming 250A, 2 ways four pole outgoing upto 100 A MCCB's on iron frame, as per specification no SW-SWR/MCCBPB.(Excluding MCCB'S)

Providing and erecting incoming and outgoing cable alleys suitable for MCCB panel board with door of 250A incoming and 2 way outgoing made from CRCA sheet 1.6 mm thick duly powder coated and having vertical insulated partition for shielding between the shared face of cable way and DB complete.

Providing and erecting prewired meter module suitable for MCCB panel board with CT's and emf's VIF meter complete.

Supplying and erecting SS enclosure for MCCB suitable for 125A to 200A MCCB complete.

Supplying and erecting marine plywood 18/19 mm thick fixed to wall or on provided panel board with necessary materials such as screws, wall fasteners, supports, nut bolts etc. complete.

Supplying and erecting iron, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority.

Supplying and erecting LT CT multifunction DLMS compliance energy meter of accuracy of class 0.5 , 3x240V,50 Hz with optical & RS 232 port, backlit LCD, measures & displays trivector energy, load survey, TOD, tamper detection & logging, power ON /OFF events, instantaneous parameters of rating 1/5 A with display in absence of power complete with zero adjustment & test certificate from manufacturer erected on provided M.S. box and connected to CTs.

Supplying and erecting AC three phase LT CT multifunction net meter DLMS compliance of accuracy class 0.5, 3 x 240V, 50Hz, with backlit LCD display, optical port & RS 232 port (measures import kWh, kVAh, export kWh, kVAh, Net kWh, kVAh, V, I, kW, 6 months history of energy, load survey,TOD, tamper detection & logging, power ON/OFF events, instantaneous parameters of rating 1/5A with display in absence of power) with wiring connections and mounting hardware on provided panels complete with calibration certificate from manufacturer.

Supplying and erecting LT current transformer with bar primary 50/5 to 1000/5 ratio with 15 VA burden erected in provided CRCA box duly secured with insulating materials connected to the meter with test certificates.

Supplying, erecting & terminating XLPE armoured cable 3½ core 70 sq. mm. aluminium conductor with continuous 8.35 sq. mm. (10 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 75 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete.

Providing earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm complete with all materials, testing & recording the results as per specification no. EA-EP

Supplying and erecting copper strip of required size used for earthing on wall and/or any other purpose with necessary copper clamps fixed on wall painted with bituminous paint in an approved manner with joints required. As per specification no. EA-EP.

Supplying and erecting GI strip of required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint in an approved manner with joints required. As per specification no EA-EP.(25x3 mm strip 100 mtr x 0.590 kg/mtr=59 kg

Supplying and erecting conventional spike type air termination suitable to carry lightning stroke made up of heavy gauge 40 mm dia copper pipe of standard length with 5 Nos. copper spikes fixed on copper ball as air terminals duly threaded in copper pipe erected on provided foundation in an approved manner.

EST 7 Supplying and erecting ISI mark modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete.

Supplying and erecting ISI mark modular type 3 pin 6A multi sockets with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting PVC Surface modular switch box with double mounting plate for 4 modules duly erected.

Supplying and erecting LED 18W tube light fitting (4 feet) with polycarbonate housing, heat sink, integrated HF electronic driver complete.

Supplying and erecting bulkhead fitting suitable for upto LED upto 12W fixed on wall. As per specification no. FG-IDF/BHF

Supplying and erecting 10-12W, 230V integral type LED Lamp suitable for B-22/E-27 base.

Supplying, erecting and marking DPMCB 6 A to 32 A B- series (for lighting) in provided distribution board as per specification no. SW- SWR/MCB

Supplying, erecting and marking FPMCB 6A to 32A in provided distribution board as per specification no. SW-SWR/MCB

Supplying and erecting CRCA sheet metal one way enclosures suitable for DP MCB /TP MCB /FP MCB erected on angle iron/GI frame complete.

Supplying and fixing CRCA sheet Box with earthing terminals for housing 2 Pole RCCB on iron frame/laminated board complete.

Supplying and fixing CRCA sheet Box with earthing terminals for housing 4 Pole RCCB on iron frame/laminated board complete.

Supplying, fixing and commissioning of 2 pole,RCBO (residual current breaker with overcurrent short circuit 10 kA and earth leakage protection), with 30/100/300 mA sensitivity and having capacity of 6/10/16/20/25A, as per specification no SW- RCCB/RCBO

Supplying, fixing and commissioning of 4 pole RCBO ( (residual current breaker with overcurrent short circuit 10 kA and earth leakage protection), with 30/100/300 mA sensitivity and having capacity of 6A/10A/16A/20A/25/A as per specification no SW- RCCB/RCBO

Supplying, erecting & terminating XLPE armoured cable 2 core 4 sq mm copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating XLPE armoured cable 4 core 6 sq. mm. copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Providing earthing with copper earth plate size 30 x 30 x 0.315 cm complete with all materials, testing & recording the results as per specification no. EA-EP

Supplying and erecting copper strip of required size used for earthing on wall and/or any other purpose with necessary copper clamps fixed on wall painted with bituminous paint in an approved manner with joints required. As per specification no. EA-EP.

SITC of Electric Traction Passenger Lift with • Rated capacity :- 16 Passenger/1088Kg • Floors :- G+1 floor (2Stops/2 Landings) • Travel :- 3 to 4.2 mtrs • Location of Lift Machine:- MR/MRL • Rated speed :- 1.0mps VS • Doors type :- COPO/TOPO Doors with frame having clear opening of 1000mm wide x 2000 mm high made from SS 304 grade sheet of 1.5mm, thick in hairline finish for car and all landing doors with SS door architraves/frames • Lift car enclosure made from SS 304 grade sheet of 1.5mm, thick with hairline finish with frame made from MS girders, bracing of adequate size with minimum safety factor of 5, with Toe Guard Apron, with necessary false ceiling with adequate LED lights, blower/fan for ventilation & SS chequered plate flooring, handrails, mirror, emergency light etc. • COP with SS face plate having metallic push buttons with Braille Code & luminous indicator around button with FPI, scrolling UP/DN LED indicator & with/without attendant key switch, OWD with audio-visual alarm, VAS in Marathi, Hindi & English with intercom system with telephone instrument in Lift car, LMR & FCC/ground floor • Clear Car size of 1600 mm wide x 1600 mm deep x 2100 mm high • LOP with SS face plate having recess/surface push button box for all landings with scrolling UP/DN LED indicator having metallic push buttons with Braille Code & luminous indicator around button with CPI, Lift car arrival & next travel direction audio-visual indication at all landings • Lift controller based on microprocessor/ PLC with VVVF Drive having closed loop control system, with IBMS compatible having necessary port, control panel duly wired with proper size & strength copper wire for power & control circuit, with provision for addition of floor/control card & allied accessories control panel having enclosure of 1.5mm CRCA sheet with powder coating with IP54 Protection class • ARD complete with necessary SMF VRLA batteries • Fireman controller having fireman switch at fire Landing, • CCTV surveillance system comprises of 2nos minimum 2.0MP FHD IP based vandal proof Dome camera in lift car & in LMR/inside lift shaft top aimed on Lift machinery & controller with NVR kept in LMR/FCC with HDR data backup for 60 days with 18" FHD TV monitor, to be kept in FCC/LMR as directed by Engineer In Charge. • Lift Machine of Gearless PMSM of suitable kW with Traction pulley, OSG, electromagnetic brakes, entire assembly mounted on adequate size girders duly fixed on LMR floor/ shaft walls complete with main/diverter traction sheaves, suspension wire ropes/belts of adequate size & strength • Other mechanical parts such as 'T' section adequate size guide rails for car & counter weight with brackets fasteners, counter weight frame with necessary blocks, buffers with necessary support arrangement, MS pit ladder etc. erected with necessary steel work • Minor civil work for alteration if any and erection of door frames and accessories, erection buffers, erection of lift machinery, adequate size core cuts if required & scaffolding for erecting guide rails fixing of girders for mounting lift machine etc. complete as per specification no. LFT.. • Lift shaft available having clear size of 2300.mm wide x 23000.mm deep, 1800 mm Pit depth,mm Overhead. 1)General: - Job includes entire procedure of obtaining all necessary erection permissions & "License to Work the Lift" from Electrical Inspector(Lifts) with submission to the Engineer In Charge. 2) Warrantee: - Job covers three years onsite warrantee for all the Lift parts with FCAMC as per the maintenance schedule.

EST 8 Supplying and erecting marine plywood 18/19 mm thick fixed to wall or on provided panel board with necessary materials such as screws, wall fasteners, supports, nut bolts etc. complete.

Supplying and erecting 525 V 3 phase, 50 Hz., MPP type capacitor having minimum overcurrent capacity of 1.8 In, peak inrush current capacity 300 In and minimum life 150000 hours kVAr bank of all polypropylene condensers (APP) with the standard capacities of 2, 3, 5, 7, 10, 12.5 and 15 kVAr units of P.F. correction for operation on 3 phase 50 Hz. with externally discharging resistances, earthing terminals and built on angle iron or channel iron frame work and provided with terminal cover box complete erected on provided iron bracket or on floor duly tested by licensee.

Supplying and erecting iron, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority.

Providing earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm complete with all materials, testing & recording the results as per specification no. EA-EP

Supplying, erecting & terminating XLPE armoured cable 4 core 10 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying and erecting four pole metal clad ON LOAD change over switch 415V, 40A erected on angle iron / GI frame complete.

Supplying and erecting ISI mark GI pipe 50 mm dia.‘B’ class at position with accessories complete. Specification no. CW-PLB/GP.

Supplying and erecting automatic control panel for 3 Ph, 415 volt, A.c. Submersible/centrifugal pump set upto 7.5 HP consisting of DOL starter having relay range 9-14 AMP,S.P.P., Combined ammeter/voltmeter, phase indicating lamp enclosed in CRCA powder coated Vibration proof enclosure with IP 54 protection. Control Panel should offer single phasing, phase reversal, phase imbalance etc

Supplying and erecting CRCA sheet metal one way enclosures suitable for DP MCB /TP MCB /FP MCB erected on angle iron/GI frame complete.

Supplying, erecting and marking FPMCB 40A to 63A in provided distribution board as per specification no. SW-SWR/MCB

Supplying and erecting flat flexible 3 core 4 sq mm PVC sheathed submersible type copper cable suitably clamped at fixed intervals with column pipe assembly complete.

Supplying and erecting submersible pump set suitable for erection on open well of 3.75 KW/5 HP with 415 V 50 c/s.A.C. supply, having delivery head from 24 to 13m. and discharge from 400 to 1000 Itrs. per minute (Max efficiency at 21m head & 680 Itr discharge) & pipe of Suction 50mm / Delivery 50 mm diameter erected with necessary H type clamps as per specification no. WP-OSP

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete.

Supplying and erecting cast iron double flange NRV of size 75/80 mm dia complete as per specification no. FF-VL/NRV

Supplying and erecting gun metal gate valve of size 50 mm dia complete as per specification no. FF-VL/GV

Making cement concrete foundation in 1:3:6 cement concrete, (20 to 25) mm. stone metal duly plastered with necessary curing for complete. (pole muffing or any other purpose).

Supplying, erecting and marking TPMCB 6 A to 32A in provided distribution board as per specification no. SW-SWR/MCB

Shubham EPC Private Limited

S.S.Construction