CONSTRUCTION OF PM SHRI SINGLE LAB OF SIZE 7 X 10.60 MTR AT KENDRIYA VIDYALAYA KANPUR CANTT

Amount

M&L for Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed.

M&L for Excavating over areas, n exc 1.5 m deep and getting out in soft/loose soil complete all as specified and directed.

M&L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L for 100 mm thick Cement concrete Type D2 (1:4:8) using 40mm graded stone aggregates as in foundations, filling floor and mass concrete complete all as specified and directed.

M&L for RCC M-25 (using 20mm graded stone aggregates) as in Foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc. basement slabs, under-reamed piles and mass concret complete all as specified and directed.

M&L for Brickwork with fly ash old size bricks built in CM (1:6) straight or curved on plan exc 6 m mean radius complete all as specified and directed.

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work vertical or to batter in flat surface complete all as specified and directed.

M&L for Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc. vertical or to batter in flat surface complete all as specified and directed.

S&F Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per item No 9.00 above but 6mm to 8mm dia complete all as specified and directed.

All as per item No 9.00 above but 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders complete all as specified and directed.

M&L for RCC design Mix M-25 (using 20mm graded stone aggregates) as in Columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for RCC design Mix M-25 (using 20mm graded stone aggregates) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc in flat surface complete all as specified and directed.

M&L for RCC design Mix M-25 using 20mm aggregates in Chajja complete all as specified and directed.

M&L for 15mm thick in CM (1:4) Rendering on fair faces of brick work or concrete surfaces complete all as specified and directed.

S&F Integral waterproofing compound complete all as specified and directed.

M&L for 5mm thick Rendering in CM (1:3) on fair faces of brick work or concrete surfaces on ceiling complete all as specified and directed.

M&L for 15mm thick in CM (1:6) Rendering on other than fair faces of brick work or concrete surfaces complete all as specified and directed.

M&L for preparation of newly plastered wall and applying two coats of cement base paint over and including a coat of alkali resistant primer complete all as specified and directed.

M&L for preparation of newly plastered wall and applying three coats of white wash on ceiling complete all as specified and directed.

M&L for preparation of newly plastered wall with chalk whiting, on plastered surfaces and applying two coats of distemper complete all as specified and directed.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM (1:6) complete complete all as specified and directed.

M&L for Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick backing coat in CM (1:3) complete all as specified and directed.

M&L for 40 mm thick PCC type B-1(1:2:4) (using 20mm graded stone aggregates) as in floors complete all as specified and directed.

M&L for Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 50 mm thick PCC type C-2 (1:3:6) (using 20mm graded stone aggregates) as in Plinth protection complete all as specified and directed.

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick screed in CM (1:6) complete all as specified and directed.

M&L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application over applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning surfaces over and including 15mm thick plastered surface in CM (1:3) using water proofing compound complete all as specified and directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of decorative type/wood grain printed colour of size 50 x 125mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type/wood grain printed colour flush door shutter of size 30 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade),calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moistureproof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed.

S&F for Factory made solid panel PVCdoor shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded decorative type/wood grain printed colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheet for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; wire gauzed i.e. panel will be of SS wire gauze in lieu of wood grain printed PVC sheet panel. The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly of wood grain printed colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (900) used instead of exposed portion of PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame at site as per direction of EIC. Note: Rate quoted by contractor shall deemed to including SS butt hinges of necessary size and SS wire gauge.

S&F 200mm stainless steel fancy handle of approved make fixed with SS screws etc complete all as specified and directed.

S&F 200 mm stainless steel barral tower bolt of extruded section complete all as specified and directed.

S&F 300 mm Stainless steel sliding door bolt with hasp and staple(bolt type) including fixing with necessary accessaries complete all as specified and directed.

S&F 300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F 75mm long aluminum anodised extruded type door stopper of double legged with rubber shoes in bottom complete all as specified and directed.

S&F MS 125mm Butt hinges, heavy weight, cold rolled mild steel complete all as specified and directed.

All as per item No 39.00 above, but wire gauzed window area exc 1 sqm but not exc 2.00 sqm each, complete all as specified and directed.

S&F Framed work such as grills, grating etc. with ends of bars shouldered and / or riveted or forget into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe 290 Gde E-165 complete all as specified and directed.

S&F 4.8 mm thick sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq.m in each pane, complete all as specified & directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F 20 mm dia GI pipe medium grade with all fittings and fixed to walls or laid in floors complete all as specified and directed.

S&F 15mm dia GI pipe medium grade with all fittings and fixed to walls or laid in floors complete all as specified and directed.

S&F of 20 mm dia gun metal globe or gate valves, with iron wheel head screwed both ends for iron pipe, complete all as specified and directed.

S&F 15 mm bore Stop valves, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F 15 mm bore chromium plated Fancy type Bib taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F 40 mm bore dia waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S&F 40 mm dia waste pipe of 850mm length for sink/WHB complete all as specified and directed.

S&F chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flange complete all as specified and directed.

S&F 1000 litres capacity Rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I incl Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

S&F soap dish, vitreous China white, of size 160x 160x90mm , any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

M&L for Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft/ loose soil complete all as specified and directed.

Returning, filling, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed.

Spreading and levelling in layers n exc. 25 cm thick and well ramming including watering as required complete all as specified and directed.

Removing excavated material exc. 250m but not exceeding 500m and depositing where directed complete all as specified and directed.

M&L for Cement concrete type B2 (1:2:4) (using 40mm graded stone aggregates) as in surface channels and drains complete all as specified and directed.

M&L for Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and directed.

M&L for Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed.

M&L for Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L for Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and directed.

M&L for preparation of new surfaces two coats of synthetic enamel paints over and including a coat of red oxide of any description, over 10 cm in width or girth not otherwise described complete all as specified and directed.

Surface dressing n exc 15cm deep in soft/loose soil complete all as specified and directed.

M&L for Providing, cement concrete Type B1 1:2:4 (using 20mm graded stone aggregates) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of decorative type/wood grain printed colour of size 45 X 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F of 20 mm thick PVC board made out of 18 mm thick PVC ply and 1 mm thick PVC ply free from rigid one side prelaminated and another side plain colour, PVC sheet stuck on both side with solvent cement adhesive to make the board of 20 mm thick cub board and wardrobe complete all as specified and directed.

M&L 75 mm size stainless steel handles complete all as specified and directed.

S&F 100 mm long hasp and staple, safety type, brass with mild steel hinge pin inculding bolt to hinge plate and fixed and screws complete all as specified and directed.

S&F stainless steel Butt hinges medium weight cold rolled of 75 mm size and fixed complete all as specified and directed.

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with out grey cement and no pigment complete all as specified and directed.

M&L for point wiring for one light/fan/bell/exhaust fan point/ controlled by one switch with 1.5 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable FRLS with proper colour coding and 1.5 sqmm PVC insulated unsheathed copper conductor single core multistranded cable (green colour) as earth lead in and including concealed non metalic rigid PVC conduit medium grade size not less than 20mm dia with all fittings (ISI Marked) controlled by one switch including CI/MS sunk box of required size & 3 mm thick plastic laminated sheet, including cutting chases to wall making good the disturbed surfaces to match with the existing specification complete all as specified and directed.

All as per item No 75.00 above but for one 5A socket outlet on the same board controlled by one switch complete all as specified and directed.

All as per item No 75.00 above but for one 3 pin 5A socket outlet independent controlled by one switch complete all as specified and directed.

All as per item No 75.00 above but for one 3 pin 15 Amps socket outlet independent with 2.5 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable (FRLSH) and 2.5 sqmm PVC insulated unsheathed copper conductor single core cable (green colour) as earth lead in and incl PVC conduit complete all as specified and directed.

M&L for switch piano flush button single pole one way 5/6 amps 240 volts complete all as specified and directed.

M&L for socket 5 amps 3 pin flush type, 230 volts complete all as specified and directed.

Supply and fixing of Exhaust Fan AC single phase 230/240 volts of size 450 mm sweep with louver shutter including providing/cutting the round hole of required size in wall, grouting of nuts, bolts, fixing the frame and exhaust fan including fixing of louver shutter with frame on the exhaust side (outer surface of wall) and cutting with and including PVC insulated three core 23/0.0076 copper cable and suitable size of flexible conduit from celling rose to exhaust fan motor and writing MES No. in black synthetic enamel paint/engraving tools etc complete all as specified and directed.

S&F of LED Aluminium batten luminaire surface mounted 4 feet system wattage of 20/22 Watts with lifetime of not less than 50000 burning hours with 70% of its initial lumen maintained.CRI>80, Power Factor>.95 ,THD<20% ,Surge protection 3 KV in CM, IP-20n Protected , meets LED IS Specifications , Class-1 , short circuit and over circuit protection voltage range-150 to 270 AC,system efficiency at luminaire level > 100lumen/watt and ibncluding connecting up with pvc sheathed 1.5 sq mm 3 core copper conductor flexible wire from ceiling rose to fitting fix complete all as specified and directed. Note:- All the above mentioned specifications will be verified through LM 79 and LM 80 report of NABL accredited lab before supply of LED fixtures.

Supply and fix sheet metal enclosure MCB distribution board, 8 way double door with IP-43 protection with 200 Amp rated bus bar complete all as specified & directed.

S&F amp rating 240 V, 10 KA 'C' curve miniature circuit breaker (MCB) 5 to 32 Amp single pole in the MCB DB with connection testing and commissioning complete all as specified and directed.

All as per item No 84.00 above but SPN 40 to 63 Amp complete all as specified and directed.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.00, Air delivery minimum 210 CMM, 350 RPM (tolerance as per IS : 3742019), THD less than 10%, all remaining accessories including safety pin, nut bolts, washers, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete all as specified and directed.

Supply,Laying, jointing and leakage testing GI Pipe medium grade 20 mm bore including supply and fixing of all fittings such as bend, tee, elbow, union, reducer etc, laid in trenches / floor/ walls etc as specified and as directed at site of the following sizes :- Notes : (i) The laying and jointing of pipes are required to be carried out in short / long streches catering to specific requirements of a purticular quarter, building block or a group of blocks.) (ii) Excavation & earth work shall be measured & paid seperately.

Removing excavated material to a distance not exceeding 50 meters and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and directed.

M&L for sand cushioning to under ground cables 8 cm thick before laying the cable and 15 cm, thick after laying, stretching and testing the cable complete all as specified and directed. Note:- Punned thickness shall be measured and paid.

M&L for Sub class ‘B’ bricks old size. laid dry flat over the cable abutting each other, length of cable equal to width of brick all as required complete all as specified and directed.

Supply and laying to wall or poles or fixing or passing through pipe, in replacement of 1100 volts grade heavy duty cable with XLPE insulated aluminium multistranded conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or strip and overall PVC sheathed 10 sqmm nominal cross section 2 core in service connections all as required and directed. (Note : Including making good all distributed wall surfaces/ flooring/tilling to match with existing specification)

murty construction company (BID ID -3331326)

Khushi Muskan Engineer & Developer (BID ID -3331395)

M/s raj constructions (BID ID -3332085)