PROVISION OF DEFICIENCY OF 24 NOS OFFICERS MARRIED ACCN (MAJOR TO BRIG) AT DIPATOLI MIL STN

Amount

SCHEDULE "A"

SCHEDULE "A" PART-I (Building Work) Lump sum price worked out by the contractor for 'Building Work' as listed in Schedule 'A' Part-I against the lump sum price inserted by the MES.

Sch 'A' Part-II (Internal Water supply) Lump sum price worked out by the contractor for Internal Water supply) as listed in Schedule 'A' Part-II against the lump sum price inserted by the MES.

Sch 'A' Part-III (Internal Electric Supply) Lump sum price worked out by the contractor for 'Internal Electric Supply' as listed in Schedule 'A' Part-III against the lump sum price inserted by the MES.

Sch 'A' Part-IV (External Water supply) Lump sum price worked out by the contractor for 'External Water supply' as listed in Schedule 'A' Part-IV against the lump sum price inserted by the MES.

Sch 'A' Part-V (External Electrific Supply) Lump sum price worked out by the contractor for'External Electrific Supply' as listed in Schedule 'A' Part-V against the lump sum price inserted by the MES.

Sch 'A' Part-VI (Road, Path and Hard standing) Lump sum price worked out by the contractor for 'Road Path and Hard standing' as listed in Schedule 'A' Part-VI against the lump sum price inserted by the MES.

Sch 'A' Part-VII (Sewage Line) Lump sum price worked out by the contractor for 'Sewage Line ' as listed in Schedule 'A' Part-VII against the lump sum price inserted by the MES.

Sch 'A' Part-VIII (Area Drainage) Lump sum price worked out by the contractor for 'Area Drainage ' as listed in Schedule 'A' Part-VIII against the lump sum price inserted by the MES.

Sch 'A' Part-IX (Fencing & Gate) Lump sum price worked out by the contractor for 'Fencing & Gate' as listed in Schedule 'A' Part-IX against the lump sum price inserted by the MES.

Sch 'A' Part-X (Rain Water Harvesting) Lump sum price worked out by the contractor for 'Rain Water Harvesting' as listed in Schedule 'A' Part-X against the lump sum price inserted by the MES.

Sch 'A' Part-XI (Arboriculture) Lump sum price worked out by the contractor for 'Arboriculture' as listed in Schedule 'A' Part-XI against the lump sum price inserted by the MES.

Sch 'A' Part-XII (Site clearance, excavation & earth works) Lump sum price worked out by the contractor for 'Site clearance, excavation & earth works' as listed in Schedule 'A' Part-XII against the lump sum price inserted by the MES.

Note for Srl No 2 to 13 The percentage above / below the SSR -2020 (part-II) rates shall be derived from the amount quoted by the contractor against Srl No. 2 to 13 by comparing it with the amount inserted / pre- priced by the department and the same shall be applicable for the items of respective schedule

Schedule 'A' Part-XIII (Miscellaneous items of works)

Internal Water Supply

Item No 01 : Supply & fixing of brass extension nipplr 15mm dia and 50-75mm long alongwith SS cover plate complete all as specified & directed.

Item No 02 : Supply & fix in repair 150mm dia CP Towel ring complete all as specified and directed.

Item No 03 : S&F bidet spray (Health faucet) with 1.20 meter tube and holder complete all as specified & directed.

Item No 04 : S&F brass chromium plated tumbler holder complete all as specified & directed.

Item No 05 : S&F brass chromium plated single lever high flow divertor including brass chromium plated bib tap and provision for overhead shower including necessary fittings handles and cover plate complete with wall flange screwed down for CPVC pipe complete all as specified & directed.

Item No 06 : S&F brass chromium plated sink mixer with swinging spout/rotatable spout with concealed legs & wall flange complete all as specified & directed.

External Water Supply

Item No 07 : S&F Ductile Iron pipe with spigot and socket ends class K-7 suitable for Tyton joint in any length laid in trenches of following size

(a) 100 MM bore

Item No 08 : S&F CI Sluice valve confirming to IS 14846 – 2000 PN-1.0 flanged ends stainless spindle of following sizes with necessary packing materials and nut bolts complete all as directed at site

(a) 100 MM bore

Item No 09 : Construction of brick masonry valve pit of size 900mm x 900mm x 900mm (internal dimensions) one Brick thick wall in cement mortar 1:4 on 100mm thick PCC 1:4:8 (40mm graded aggregate) in foundation, Rendering 15mm thick internally and externally upto 150mm below GL, providing 3.0mm thick MS sheet valve pit cove, welded with 40 x 5mm flat iron frame around including provision of hinges, handle and locking arrangement and 40 x 40 x 6mm angle iron frame fixed on top of valve pit by means of holdfast 150mm long embedded in PCC 1:2:4 (20mm graded aggregate) Block size 230 x 200 x 100mm, applying two coats of anti-corrosive paint over a coat of red oxide zinc chrome primer after preparation of all exposed to steel surfaces including necessary excavation & Earth work in soil complete all as specified and shown on drawing.

Item No 10 : Cutting of existing DI pipe line of size 150 to 350mm bore for fixing Tee, Sluice valve etc all as dierected and shown by Engr-in-Charge. Note - Excavation, refilling and removal measured seperately.

External Electrical Supply

Item No 11 : Supply and installation testing and and commissioning outdoor LT panel totally enclosed weather and vermin proof, suitably ventilated, 440 Volts, 50HZ,AC supply, fully compartamentalised cubical type made out of 3 mm thick CRCA sheet steel for load bearing and 2.0 mm thick non load bearing portions, protection of enclosure IP-54 as per IS-2147 of 1962 complete with pretreatment and powder coating of approved colour including suitable angle iron/flat iron frame work/supports, excavation and earth work, PCC foundation etc, including the follwoing switchgear, supplied fitted and connected internally complete with bus bar all as directed and specified by Engr-in-charge :- (a) 4 Nos copper bus bar of current rating capacity 350 Amp with digital ammeter, voltmeter, current transformer of suitable rating, astromonical Street light timer with contactor and relay. (b) MCCB TPN, 415 volt adjustable type, 200 Amps with breaking capacity 25 KA- 01 No (Incoming ) - 01 Nos (c) MCCB TPN 415 volt 125 Amps wirh breaking capacity 16 KA-03 Nos (outgoing)

Note : 1. The size of panel and size of each compartment should be as per relavent IS code and Engineering practices. 2. Contractor has to submit the general arrangement drawings of LT panel for approval to GE before placing the order.

Item No 12 : M&L for trenchless boring under road crossings/foot paths by manual / Boring machine complete all as specified and directed at site.

Item No 13 : M &L for GI Earthing complete with GI earth plate electrode 60cm x 60cm x6 mm buried directly in ground verticvally to size of earth pit not less than 0.90x 0.90 x 2.25 mtr below ground level with top edge of the plate at a depth not less than 1.5 mtr below ground level, earth plate connected to galvanised earth strip of size 32 x 6 mm, 7.5 mtr long (Min) by means of brazing nuts, bolts, check nuts, & washers ,testing of completion (drawn in earth strip protection pipe light gade GI of size 40 mm dia) by means brazing at both edges with vertical plane of electrode all as shown in plate No 3 of SSR Part - I filling with charcoal dust , and common salt , including necessary excavation and earth work in any type of soil ,perforated watering pipeof size 15 mm dia,funnel with wire mesh,earth strip protection pipe light grade PCC chamber 1:3:6 type C1 (for even finish on both the faces) and RCC cover 1:2:4 Type B1,450 x450 x50 mm thick with 6 mm dia CTD bars 150 mm c/c with 2 Nos of handles of 10 mm dia steel rod all as specified and directed and testing on completion and connected to equipment with lugs and screw nuts etc all as specified and directed by EIC

Item No 14 : Blank

Item No 15 : Blank

Item No 16 : Blank

Item No 17 : Blank

Item No 18 : Blank

Item No 19 : Blank

Item No 20 : Blank

Item No 21 : Blank

Item No 22 : S and F polycarbonate junction loop in / loop out box of internal size 250 x 210 x 115mm made out of FRP (Hot moulded type) with weather proof canopy and locking screws alongwith 5/6 Amps MCB-01 No, 15 Amps rated 3 pole connector - 01 Nos, neutral link mounted and Din rail suitable size for mounting MCB/Connector complete in the box, duly fixed to steel tubular pole using 25 x 3mm FI clamp with suitable gland and lugs for connecting cable incomplete all as specified and as directed.

Sewage Line

Item No 23 : M & L M-30 Design mix, Septic tanks, exc in ordinary soil, foundation in PCC !:2:4, brick work in CM 1:4 RCC slab covers including RCC precast manhole cover having 6 mm plate embedded all round / fibre reinforced cover with iron frame Vent shaft and sludgechambers etc, complete for 100 users complete all as specified and directed.

Item No 24 : M & L Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size 1.8m dia x 3.0m eff depth complete all as specified and directed

Item No 25 : Supply and laying and testing of 150mm inner dia of double wall corrugated (DWC) high density polethelene pipes(HDPE) and stiffness class-8 (SN-8) with ISI marked (with CML No) with and incl all fittings and jointing materials for sewage line and laid in trenches as specified in IS-16098(Part-2) 2013 and as per manufacturers instruction complete all as specified and directed. Note: Bedding of pipe shall not be provided in normal condition and construction methods shall be strictly compellled as per clause No A-4 Annex'A' of IS 16098 (Part-2) 2013.

Item No 26 : S&F SFRC MH cover with frame confirming to IS 12592:2002 HD 20 grade, of size 750mm circular or rectangular surrounded with steel strip 70 x 1.5mm reinforced shall be as per relevant IS and laid over man hole brick work or concrete in CM 1:4 including reinforcement complete all as specified and directed. Note: (i) Make of SFRC Manhole/drain cover and frame (a) M/s PS concrete (b) M/s KK Manhole or as approved by GE (ii) Contractor shall provide PV alongwith manufacturers certificate of SFRC cover (iii) Reinforcement shall not be measured and paid seperately.

Arboriculture

Item No 28 : Supply of best quality loose (Sweet earth) for plantation complete as per gardening parctice complete all as specified and directed.

Item No 29 : Supply of approved manure (Cow Dung) complete as per gardening practice and complete all as specified and directed.

Item No 30 : Supply of vermi compost of best quality complete as per gardening practice and complete all as specified and directed.

Item No 31 : Supply and plantation of croton and hedge of height not less than 450mm above ground level, including preparation of ground to required depth and filling of good earth cow dung and watering etc complete all as specified and directed.

Item No 32 : Supply and plantation of Ashoka plants height of plant not less than 6ft-8ft above ground level including preparation of ground upto 60cm deep and filling of good earth, cow dung, vermi compost and watering etc complete all as directed by the Engineer-in-Charge.

Item No 33 : Supply and plantation of Palm tress height of plant not less than 6ft-8ft above ground level including preparation of ground upto 30cm deep and filling of good earth, cow dung, vermi compost and watering etc complete all as directed by the Engineer-in-Charge.

Item No 33(a) : Ficus Reginauld (Common name- Weeping Fig) 3-4 ft

Item No 33(b) : Ficus Blackeana (Common Name- Rubber Plants) 5-6 ft height

Item No 33(c) : Plumeria Alba (Common name- White frangipani) 5-6 ft height

Item No 33(d) : Delonix Regia (Common Name - Royal Poinciana) 5-6 ft height

Item No 33(e) : Caesalpinia Pulcherrima 'Rosea' (Common name - Pink peacock Flower) 1/2-1ft height

Item No 33(f) : Tabernaemontana coronaria( Common Name- Crape Jasmine) 2 ft height

Item No 33(g) : Wadelia Trilobata (Common Name- Creeping Oxeye) 2-3 ft height

Item No 33(h) : Duranta golden (Common Name - Golden Dewdrop)2-3 Ft height

Internal Electrification

Item No 34 : S & F modular type TV Socket out let complete all as specified and as directed.

Item No 35 : S & F modular type LAN Socket RJ 45 with complete box

Item No 36 : S & F modular type Telephone socket RJ 11/12 with complete box

Item No 37 : S & F modular MCB protected socket comprising of 24A MCB C curve, and 16/20 A Socket for AC/Geyser, modular switch 16A complete with Sheet metal Enclosure for 230 volt 50 Hz AC including all acessories as one complete set all as specified and as directed .

Item No 38 : S & F of LED bulb E27 Cool Day light 9 watts rECHARGABLE having Luminous Efficacy range lies between ( ≥90 and <105 ) lm/W as per BEE guidelines.

Item No 39 : S&F Electric Kitchen chimneys heat auto clean with motion sensor auto off function, touch sensor control LED loghting, metal housing brushless DC motor, auto clean alarm, mood light material tempered glass, noise level not less than 70 dB of size 90cm and suction power 1250m3/hr with suitable size of flexible exhaust (up to 20feet 4/6 inch) including all fixing arrangement complete 6 way silent filterless, 12 yr warranty on motor (2 yr comprehensive), Autoclean alarm Mood Lt.

Item No 40 : Supply, installation, commissioning and testing of electric water heater (geyser) of capacity 15 ltrs vertical storage PVC outer body of 5 star rating, inner tank made of MS glass line coating with anti corrosion 1KW/1.KW, pressure rating 0.8 Mpa, heating element of anodized rod with safety valve, thermostate, NRV, connecting pieces, necessary gate valve of suitable size etc including all fixing arrangement complete all as specified and directed by Engineer-in-charge.

Item No 41 : Supply, installation, commissioning and testing of instant electric water heater(geyser) of capacity 5 ltrs/6 ltr (or nearest higher standard size) vertical storage ABS Plastic outer body of 5 star rating (highest star rating available in market by company), inner tank made of stainless steel inner tank of 304 grade with anti corrosion 3 KW, pressure rating 8 bar, heating element of anodized rod with safety valve, thermostate, NRV, Connecting pieces, necessary gate valve of suitable sizeetc including all fixing arrangement complete all as specified and directed by Engineer-in-charge.

Item No 42 : M&L for earthing complete with galvanized earth plae electrode 600mmx600mmx6mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtre below ground level connected to galvenised earth lead wire of 4mm dia by means of nuts, bolts, washes of galvanized iron or steel all as shown in electrical plate No 3 and testing on completion including adequate charcoal dust comman salt necessary excavation & earth work PCC (1:3:6) type C-1 pit with precast RCC Cover slab 40 mm thick in PCC(1:2:4) type B-1 100 mm c/c both ways with funnel wire mesh and 20 mm dia GI pipe heavy grade as watering pipe and 15 mm dia GI pipe heavy grade for protection of GI wire up to 7.5 mtr connected to earthing point complete all as specified and as directed.

Item No 43 : Supply and fix Decorative wall light made up of high grade engineering plastic material suitable for 9/12 W LED lap B22 base Complete all specified and as directed.

Item No 44 : Supply and fix Decorative gate light made up of high grade unbreakable polycarbonate material suitable for retrofit LED lamp B22 base Complete all specified and as directed.

Item No 45 : S&F wall mount fan for kitchen 400mm, 3 blades button conrol, material aluminium powder coated finish with cord, blade of plasic material including all fixing arrangement complete all as specified.

Furniture

Item No 46 : Almirah Medium Steel (FD-1032) :- Overall size shall be 760mmx 440mmx1270mm, Top, Sides. Bottom and Back of Almirah shall be of 1mm thick MS Sheet. Lock shall be of made of Harison/Godrej. CP handle of 100mm long shall be provided as per drg.All joints, welding and fixing shall be done in accordance with standard workmanship. All Steel surface internally and externally expose to view shall be given two coats of smoke grey enamel paint over a coat of primer after preparation of steel surfaces. Rest all as per drg and specified.

Item No 47 : Almirah Large Steel 1/2H,1/2S (FD/E6/MAP/18): All as per shown on drawings. Top, sides, bottom, back, front and shelves of Almirah shall be of 1mm thick MS sheet. Sheet shall be hot rolled carbon steel sheet as per IS 1079:2009 or cold reduced low carbon steel sheet as per IS 513: 2008. The sheet shall be of any designation or grade as per the relevant Indian Standards. All joints, welding & fixing shall be done in accordance with the standard workmanship and specification shown in drawing. A three-way bolting device controlled by a brass lock of Make:-Godrej/Harrison/Link and operated by a chromium plated metallic S -Type handle-01 No, shall be provided to Almirah large steel. 04 Nos plinth screw (Plastic inserted molded screw) shall be provided in legs of Almirah.

Item No 48 : Bath Mat PVC (FD/E6/MAP/07) : All as shown of drawing. Legs shall be of 10x100mm in arc at four corners and 25mm dia at center. PVC seat shall be of 5mm thick. Stiffeners shall be of 3x10mm thick molded along with the seat in single piece. All PVC work shall be of standard class PVC of Make-Neelkamal/ Amko/Cello/ Supreme.

Item No 49 : Bed Hard Steel (FD/E6/MAP/08( R)): All as per shown on drawings. Steel tube or square pipe shall be made using hot rolled carbon steel sheet as per IS 1079: 2009 or cold reduced low carbon steel sheet as per IS 513: 2008. The thickness of sheet shall be 18 gauge. The sheet shall be of any designation or grade as per the relevant Indian Standards. 18/19mm thick Pre-laminated MDF Board both side teak face laminated shall be provided to head board and foot board of Bed hard. 04 Nos PVC hard rubber shoes shall be provided to legs of Bed Hard. 12mm thick commercial plywood, boiling water resistance (BWR) Grade shall be used as hard top to Bed hard.

Item No 50 : Bin Linen Multipurpose (FD/E6/MAP/09) : Overall size of Bin soiled linen (MP) shall be 1200x450x750(mm). The top/shelves/partition/shutters/sides and front of drawer of bin soiled linen(MP) shall be made up of 18mm thick Comm plywood MR Gde pasted with 1mm thick sunmica on one side of approved shade. PVC edging of Make :REHAU thikness .8mm of matching shade shall be provided . The sides/back/bottom of drawer and back of bin soiled linen shall be 12mm thick commercial plywood. Drawer shall be run on telescopic channel of appropriate size and make of Godrej/Hettich/Ozone. Leg/Base of size 75mmx25mm shall be made of hardwood teak provided all around to the bottom of the unit. 100mm CP handle shall be provided to the drawer and shutter of the unit.

The shutter shall be hang on Oxidized continuous piano type hinges confirming to IS-3818 shall be fixed with steel screws (15mm long). All exposed timber surfaces of direct vision shall be french polished to glossy finish. under side wooden members which are not french polished shall be sand papered to smooth surface and shall be treaded with one coat of varnish. Rest all as per drg and specified.

Item No 51 : Chair dining Cushioned (FD/MAP-II/04) : Chair dining shall be made of first class seasoned hard wood teak free from knots and cracks. Seat shall be made of 75mm thick, 32 density foam with approved fabric/tapestry (Rate not less 350/-Mtr) pasted on 12mm thich MR Gde comn ply. PVC nylon buffers shall be provided in toe of legs. All exposed timber surfaces of direct vision shall be french polished to glossy finish. Rest all as per drawing and specified.

Item No 52 : Chair Varandah (FD/MAP/II/06):. All as per shown on drg. Frame shall be made of 19mm dia MS tube 1.6mm thick as specified in drg.PVC seat & back shall be 4mm thick with not less than 1.85 kgs and Grooves 90x10mm shall be 10 Nos on seat & back shall be provided as per drg.PVC White shoes shall be provided to the toes of legs. Make of Seat and back-AMKO/Cello/Comfo.All MS Steel shall be painted with Two coat of white synthetic enamelled paint over a coat of primer. Rest all as per drg and as directed by Engr-in-Charge.

Item No 53 : Chair Writing Cushion (FD/E6/MAP/12) : All as shown on drg. frame of chair writing steel shall be made out of cantilever type powder coated MS Tubular frame size of 25mm x 10mm section. The polyurethane foam shall be 50mm thick and shall be moulded with density 50-55 KG per cubic mtr thickness and hardness 20 +/-2 KG on hampden machine. The shade & quality of fabric shall be approved by GE. Rest all as per drg and as directed by Engr-in-Charge.

Item No 54 : Chair Computer (FD/E6/MAP/01) : All as shown on drg. The shade & quality of fabric shall be approved by GE. Rest all as per drg and as directed by Engr-in-Charge.

Item No 55 : Charpoy Folding IP with hard Top (FD-388 (R)): All as per drawings. Steel tube or square pipe shall be made using hot rolled carbon steel sheet as per IS 1079 : 2009 or cold reduced low carbon steel sheet as per IS 513 : 2008. The thickness of sheet shall be 16 guage. The sheet shall be of any designation or grade as per the relevant Indian Standards. 12mm thick (9 ply) decorative plywood with ornamental veneers on one side, boiling water resistance (BWR Grade )shall be used as hard top . All steel surfaces shall be powder coated.

Item No 56 :Charpoy MS Tube with plywood Top (FD/MAP-II/01): All as per drawings. 12mm thick (9 ply) commercial plywood, boiling water resistance grade (BWR Grade and AA Type as per IS 303: 1989) shall be used as hard top of make: - Greenply/ Archidply / Centuryply to charpoy MS Tube. Steel Pipe shall be using hot rolled carbon steel sheet as per IS 1079: 2009 or cold reduced low carbon steel sheet as per IS 513: 2008. 04 Nos PVC hard rubber shoes shall be provided to legs of Charpoy MS Tube.The steel members shall be painted with powder coating(Black).

Item No 57 : Hat stand with mirror (FD-233) : All as per drawings. Overall size shall be 1000mm long, 710mm high. Timber shall be of first class hard wood. 4mm thick plywood one side teak face and other side commercial face and 4mm thick plywood both side commercial face for back of mirror shall be provided. Mirror 5mm thick glass electro copper plated mirror of best quality shall be provided. 4 Nos of brass Pegs of size 120mm X 75mm (overall) shall be provided to Hat Stand with Mirror. Two Nos Key plates shall be provided of M S Sheet to hat stand with mirror as shown on drawing.All exposed timber surfaces of direct vision shall be French polished to glossy finish. Under side wooden members which are not French polished shall be sand papered to smooth surface and shall be treated with one coat of varnish

Item No 58 : Ladder Aluminium (FD-1025): All as shown on drawing. Two aluminium stringers 60mm x 31.75mm made in ‘C’ shape and 3.18mm thick aluminium shall be 2310mm long and joined together with aluminium rungs of aluminium conduit fluted pipe rungs ends bed to shape as shown on drawing. Eight aluminium rungs of aluminiumconduit pipe of wall thickness not less than 2.43mm shall be equally spaced after leaving 150mm from bottom and top. Hard rubber cap/shoes shall be provided to bottom and top of aluminium stingers. Overall size of aluminium ladder shall be 2310mm long and 363.5mm wide. The clear space between the stringers shall be 300mm.

Item No 59 : Table peg (FD-277): All as shown on drawing. Overall size shall be 450mm long, 300mm wide and 380mm high. Timber species shall be 1st class hard wood teak . Two Nos additional top rail (40mm x 20mm) shall also be provided in the shorter direction at top frame of Table Peg. 18mm thick, shall be provided in lieu of 18mm thick particle board as top of Table Peg. 0.8mm thick decorative laminate sheet (HPL), shall be provided on one face (exposed face) on plywood of top of Table Peg. 4mm thick teak wood lipping/edging shall be provided to all exposed edges of top of Table Peg. The make of decorative laminated sheet is Mereino/Greenlam/Centuryply. Hard PVC toe rings shall be provided to all 4 legs fixed with steel screws. All exposed wooden/ plywood surfaces of direct vision shall be French polished to glossy finish. Other side of wooden members/plywood which are not French polished or laminated shall be sand papered to smooth surface and shall be treated with one coat of varnish.

Item No 60 : Plate rack (Trade Pattern): This shall be procured directly from manufacturer or their authorized dealer of Make: - Prayag/Jyoti/ Devidayal.

Item No 61 : Receptacle PVC (FD/E6/MAP/13) : Receptacle shall be made of thick polymer plastic and of capacity 20 Ltrs with pendulum type lid and steel handles on both sides all as shown on drg. The colour shall only be Red, Green or Blue. The Contractor may also provide the readymade Receptacle PVC of Make: - Milton, Cello or Brite with same specifications.

Item No 62 : Rack Shoe Steel (FD/E6/MAP/02( R)): All as shown on drawing. Overall size of Rack Shoe steel shall be 880mm height, 700mm width and 300mm depth. Side/Main frame shall be made with 25mm dia MS Pipe of wall thickness 18 gauge. Rack shall be made out of 20mmdia MS Pipe with wall thickness 18 gauge with 3 Nos 3mm dia horizontal bar and 9 Nos vertical bars at equal distance. All steel surfaces shall be powder coated. Thickness of powder coating shall be not less than 75 micron. The shade of powder coating shall be as black. Hard rubber shoes shall be fixed to legs of Rack Shoe Steel.

Item No 63 : Side Board : All as per shown on drawings. Timber shall be of first class hard wood teak. The top/ shelves/ partition/shutters /sides and front of drawer of Side board shall be made up of 18/19mm thick Comm plywood MR Gde pasted with 1mm thick sunmica on one side of approved shade. PVC edging of Make :REHAU thikness .8mm of matching shade shall be provided . The sides/back/bottom of drawer and back of Side board shall be 12mm thick commercial plywood. Drawer shall be run on telescopic channel of appropriate size and make of Godrej/Hettich/Ozone. Leg/Base of size 75mmx25mm shall be made of hardwood teak provided all around to the bottom of the unit. 100mm CP handle shall be provided to the drawer and shutter of the unit. The shutter shall be hang on Oxidized continuous piano type hinges confirming to IS-3818 shall be fixed with steel screws (15mm long). All exposed timber surfaces of direct vision shall be french polished to glossy finish. under side wooden members which are not french polished shall be sand papered to smooth surface and shall be treaded with one coat of varnish. Rest all as per drg and specified. FD-241

Item No 64 : Sofa set 5 seater cushioned(3+1+1) : All as per shown on drawings. Timber shall be of first class seasoned hard wood teak free from knots and cracks. 100mm thick polyurethane flexible foam, 90% open cell, minimum density 40Kg per cubic meter seat and back cushion shall be provided. Cost of tapestry cloth for chair cushion shall be not less than Rs. 350/- per RM and shall be approved by GE/Engr-in-Charge. 04Nos hard rubber shoes shall be provided to legs of Sofa Set 05 Seater (3+1+1). All exposed timber surfaces of direct vision shall be french polished to glossy finish. under side wooden members which are not french polished shall be sand papered to smooth surface and shall be treaded with one coat of varnish. FD-281

Item No 65 : Stool dressing cushion (FD/E6/MAP/14) : All as shown on drawings. Overall size shall be 450mmx300mmx380mm high. All wood shall be first class indian hard teak wood . Legs shall be of 50x30mm in section through out 380mm high. Two shorts stiffener joining legs in short sides at 100mm from bottom shall be provided as 19mmx25mm in section teak wood . A long stiffener shall be provided in the middle of short stiffeners joining the short stiffener joining the short stiffener. 75mm thick 32density foam cushion uphostered with tapestry of approved shade pasted on 12mm thick plywood. all wooden surface shall be french poshided with high glossy finish. rest all as per drg and as directed by Engr-in-charge.

Item No 66 : Table bed side (FD/MAP/07) : All as shown on drawings. Overall size shall be 450mmx350mm x500mm high. 18/19mm thick, Plywood BWR grade shall be provided in lieu of 18mm thick pre-laminated MDF board of 1mm thick decorative laminate sheet shall be provided on one face (exposed face) of plywood of table bed side. One pair (02 Nos) high precision telescopic channel made of SS 1.25mm thick of 45 kg capacity to be designed as per drawer size and to meet the weight requirement to ensure smooth movements of with / without content weights shall be provided to pull out drawer of make:- Hettich/Ebco/Godrej. 02 Nos concealed S S butt hinges and one magnetic wall catcher of make: - Hettich shall be provided to shutter of table bed side.

Item No 67 : Table centre (FD-274) : All as per shown on drawings. Timber shall be of first class hard wood teak. 18/19mm thick, 11Ply, BWR grade, AA type plywood as per IS 3030:1989 shall be provided in lieu of 18mm thick particle board. 1mm thick decorative laminate sheet shall be provided on one face (exposed face) of plywood. 4mm thick teak wooden lipping/beading shall be provided to all exposed edges plywood. Two Nos additional top rail (40 x 20mm) shall also be provided in the shorter direction at top of Table Centre. 04Nos hard rubber shoes shall be provided to legs of Table centre. All exposed timber surfaces of direct vision shall be French polished to glossy finish. Under side wooden members which are not French polished shall be sand papered to smooth surface and shall be treated with one coat of varnish.

Item No 68 : Table dining (6 Pers) (FD/MAP-II/03) : All as per shown on drawings. Timber shall be of first class hard wood teak. 18/19mm thick, BWR grade plywood as per IS 3030:1989 shall be provided in lieu of 18mm thick particle board. 1mm thick decorative laminate sheet shall be provided on one face (exposed face) of plywood. 4mm thick teak wooden lipping/beading shall be provided to all exposed edges plywood. 04Nos hard rubber shoes shall be provided to legs of Table dining 6 persons. All exposed timber surfaces of direct vision shall be french polished to glossy finish. under side wooden members which are not french polished shall be sand papered to smooth surface and shall be treaded with one coat of varnish.

Item No 69 : Table dressing ladies (FD/E6/MAP/07): All as shown on drawing. 18mm thick BWR grade plywood with 1mm thick sunmica paste on one side of approved shade shall be provided in lieu of 18mm thick pre-laminated MDF Board. 12mm thick BWR grade, plywood shall be provided in bottom, sides and back of drawer and 18mm thick plywood with 1mm thick sunmica pasteon outer side shall be provided in front of drawer. 1mm thick of maching shade PVC edging of Make- Rehau or equivalent shall be provided to all exposed edges of plywood. The thickness of glass shall be 5mm, silvering, copper coating, protective coating, reflectance shall be as per IS 3438:1994. Coating shall be done by using electroplating process. 6mm thick, BWR grade, plywood as per IS 303:1989 shall be provided in the back of mirror. 75mm thick polyurethane flexible foam, 90% open cell, minimum density 32 kg per cubic meter shall be provided to top of stool.

Cost of the tapestry cloth for cushion shall not less than Rs. 350/- per meter and shade shall be as approved by GE. 01 No chromium plated brass flush drop handle of 100mm size with fixing holes shall be provided to each drawer. 01 No stainless steel flush handle of 100mm size shall be fixed to each cabinet shutter. One pair (02 Nos) high precision telescopic channel made of mild steel 1.25mm thick of 45 kg capacity to be designed as per drawer size and to meet the weight requirement to ensure smooth movements of drawer with / without content weights shall be provided to each drawer of make:- Hettich/Ebco/Godrej .all wood surfaces exposed to view when placed in position shall be french polished with high glossy finish.

Item No 70 : Table writing (FD-275): All as per shown on drawings.The top & cabinet and front drawer shall be made up 18/19mm thick BWR grade plywood pasted with 1mm thick sunmica on one side of approved shade . PVC edging of Make- Rehau or Equivalent thickness 1mm of maching shade shall be approved. The side and back of drawers shall be made of 12mm thick teakwood. All the timber part shall be first class teak wood free froms cracks & Knots .100mm CP handle shall be provided to drawer and cupboard of table instead of knob. Magnetic Catcher shall be provided one nos in cupboard. All wooden surface shall be polished with french polish till attianing glossy finsh. Rest all as per drg and specified.

Item No 71 : Table Computer (FD/E6/MAP/03) : All as shown on drg. Top /side / bottom/ drawer/ trays shall be made of 18/19mm thick BWR commercial plywood pasted with 1mm thick laminated sheet both side of approved shade. PVC edging of Make- Rehau or equivalent thickness 0.8mm of matching shade shall be provided all round the edges. Drawer and key board tray shall be run on telescopic channel of appropriate size .

Item No 72 : Teapoy (FD-382): All as shown on drawing. Timber species shall be 1st class hard wood teak . Two Nos additional top rail (40mm x 20mm) shall also be provided in the shorter direction at top. 18mm thick BWR grade shall be provided in lieu of 18mm thick particle board as top of Teapoy. 1mm thick decorative laminate sheet shall be provided on one face (exposed face) on plywood of top of Teapoy. 4mm thick teak wood lipping/edging shall be provided to all exposed edges of top of Teapoy. The make of decorative laminated sheet is Merino/Greenlam/ Centuryply. Hard PVC toe rings shall be provided to all 4 legs fixed with steel screws. All exposed wooden/ plywood surfaces of direct vision shall be French polished to glossy finish. Other side of wooden members/plywood which are not French polished or laminated shall be sand papered to smooth surface and shall be treated with one coat of varnish.

Item No 73 : Teapoy Verandah (FD/E6/MAP/17): All as per shown on drawings. Top shall be 18/19mm thick, BWR grade, plywood as per IS 3030:1989 shall be provided in lieu of 18mm thick particle board. 1mm thick decorative laminate sheet shall be provided on one face (exposed face) of plywood. PVC edging of Make- Rehau or Equivalent thickness 0.8mm of maching shade shall be provided to all exposed edge. 04Nos hard rubber shoes shall be provided to legs of Teapoy Verandah.

Item No 74 : Trolley for TV (FD/E6/MAP/04( R)) : All as per shown on drawings. Timber shall be of first class hard wood teak.The top/ shelves/ partition/shutters /sides/back of TV trolley shall be made up of 18/19mm thick Comm plywood MR Gde pasted with 1mm thick sunmica on one side of approved shade. PVC edging of Make :REHAU thikness .8mm of matching shade shall be provided . Drawer shall be run on telescopic channel of appropriate size and make of Godrej/Hettich/Ozone. 100mm CP handle shall be provided to the drawer and shutter of the unit. 06 mm thick tint brown glass duly polished in all sides shall be provided in lieu of acrylic sheet as specified in drg . Glad shall be hang on stainless steel patches/hings fitting 02 Nos per shutter. magnetic wall catcher with stainless steel 50x30 push plate shall be fixed in each shutter for opening and closing. heavy duty revolving double wheel 06 Nos shall be provided all edges of TV Trolley . Rest all as per drawing and specified.

Nand Lal and Sons (BID ID -3155217)

MS SHRI B.C. DAS (BID ID -3161514)

SOOD ASSOCIATES PVT LTD (BID ID -3156101)