SPECIAL REPAIR OF BUILDING NO P 96 SINGLE LIVING IN ACCN OF SNCOS AT AFS AMLA

Amount

B/R Portion Taking down cement plaster on brick or stone walls etc, including racking out joints, hacking for key, scrubbing down with water etc., all as directed.

M&L for rendering 10 mm thick on fair faces of brick or stone surfaces of walls in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed.

M&L (10+5)mm thick for rendering fair faces of brick work or Concrete surface in two coats 10mm thick in CM(1:6) as under coat 5mm thick CM (1:4) as finishing coat in two separate layer mixed with liquid water proofing compound in finishing coat only with liquid waterproofing compound @ 200ml per bag of cement finished even and smooth without using extra cement complete all as specified and as directed. Note: Water proofing compound shall be measured and paid seperately

M&L 5mm thick rendering in cement mortar 1:3, on ceiling, surface finished even and fair complete all as specified and directed.

Supply only liquid water proofing compound.

M&L two coats of oil emulsion distemper on wall newly plasterd surfaces over a coat of chalk white primer complete including prepatation of new surfaces complete all as specified and directed.

M&L for 3mm thick wall care putty on wall surfaces smooth finish

M&L for two coat of cement base paint over one coat of alkali resistant primer paint including preparation of newly plastered surfaces of wall complete all as specified and directed.

M&L for preparation of newly decorated surface of ceilings and applying three coats of white wash complete all as specified and directed.

M&L for 75 mm thick plain cement concrete 1:3:6, Type C-2 using 40mm graded stone aggregate, as in plinth protection complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as directed.

M&L for digital glazed ceramic tiles in vertical surfaces 350 x 250 x 7mm/450 x 350 x 7 mm thick set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles including 10mm thick backing coat in cement mortor 1:4 complete all as specified and directed.

M&L for Non - skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match set, over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed.

Taking down Chowkat or frames, area exc 1.5 sqm but not exc 4 sqm each with shutter (without taking off shutters from the frames) complete all as specified and directed .

Taking down chowkhats or frames, area not exc 1.5 sqm with shutters (without taking off shutters from the frames) complete all as specified and directed

S&F Pressed steel frames of size 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., including one shop coat of primer complete all as specified and directed. Note: (i) The sizes/ dimensions and type (profile) of frames shall be as shown in relevant I.S. (ii) Filling hollow of frame with plain cement concrete and/ or with cement mortar shall be measured and paid separately.

M&L for plain cement concrete type B0, 1:2:4 (12.5 mm graded aggregate) in door and windows frames, any size, single or double rebated, including ar?rangement for fixing of hinges and fixtures as required

S&F Second class hard wood, Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed.

S&F factory made 35 mm thick second class hardwood, Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers complete all as specified and directed.

S&F Second class hard wood 35 mm thick glazed and skeleton shutters open rebated and prepared to receive glass, gauge etc., divided in to squares with plain, chamfered or rounded, mitred and rebated sash bars fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR Part-1, section 8, clause 8.24(a) for doors, complete all as specified and directed.

S&F Second class hard wood 30 mm thick glazed and skeleton shutters open rebated and prepared to receive glass, gauge etc., divided in to squares with plain, chamfered or rounded, mitred and rebated sash bars with edges of sash bars and framing moulded fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR Part-1, section 8, clause 8.24(b) for window and ventilator, complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F 100 mm size Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21

S& F 100 mm size mild steel butt hinges medium weight ,cold rolled.

S& F 75 mm size Stainless Steel butt hinges.

S& F 150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified (SI marked)

S&F 100mm long aluminium anodised barrel tower bolts of extruded section complete all as specified. (ISI marked).

S&F 150mm long size extruded aluminium alloy handles, cast type anodised complete as specified. (ISI Marked).

S&F 100mm long size extruded aluminium alloy handles, cast type anodised complete as specified. (ISI Marked).

S&F aluminium plate type -II, Gate and shutter, hooks and eyes 150mm

S&F 300mm long aluminum alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloy and fix complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frames including punching or drilling out old glazing pins/spring clips, providing and fixing new ones and disposing off the rubbish materials in low lying areas of defence land complete all as directed.

S&F sheet glass 3mm thick ordinary quality and glazing with wooden beading and pin in squares in squares not exc 0.50 sqm in each panes in wooden window complete all as specified and directed.

S&F 3mm thick figured glass, pin headed type and glazing with oil putty in squares n.exc 0.5 Sqm in each pane complete all as specified

S&F in repairs Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

M&L for preparation of new wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specifed and directed.

M&L for preparation of old painted wooden Surfaces of any description, over 10cm in width or girth,not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for cutting openings through brick walls built in cement mortar for the door, window and other openings or enlarging existing openings converting window in to door openings, etc., or cutting out defective brickwork for under-pinning, including providing fixing and removing shoring, cleaning and stacking bricks and removing surplus to store and rubbish off the premises complete all as specified and directed.

M&L Brick work in cement 1:6; using modular size fly ash brick, having compressive strength of minimum 75 kg/ sq. cm, straight or curved on plan exc. 6 metre mean radius complete all as specified and directed.

Demolition of un-reinforcement cement concrete as in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work and disposing of debris out of MD land complete all as specified and directed.

M&L for providing cement concrete 30mm thick PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate as in padding on roofs slab to receive water proofing treatment, laid to required slope, finished even and smooth without using extra cement complete all as specified and directed.

M&L for cleaning of roof surfaces and applying a coat of oil base bituminous primer @ 0.30 lit per sqm including laying of APP based polymeric membrane weighing not less than 3.00 kg/ Sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt,not less than 150gms/sq. m) laid on primed surface by tension application with 100mm overlap travers and 150mm overlap longitudinal and finishing the top surface by applying two coat of aluminium paint @ 0.2kg/sqm on each coat including taking down old treatment complete all as specified and directed.

S&F in repairs Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed.

S&F in repair vitreous China squatting pan, ' Orissa’ pattern, size 580 x 440 mm white, with integral footrests (excluding flushing cistern and flush pipe) complete all as specified and directed.

S&F in repair vitreous China wash down water closet pan (pedestal pattern) white, including seat and cover for pedestal pan, connection trap to drain and flushing pipe complete all as specified and directed.

S&F PVC (SWR) 110mm dia 'P' trap including connecting to out let with solvent cement complete all as specified and directed.

S&F PVC (SWR) 110mm dia 'S' trap including connecting to out let with solvent cement complete all as specified and directed.

M & L in repairs for PVC (SWR) nahani trap, plain with grating suitable for 75mm dia outlet pipe including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) with solvent cement complete all as specified and directed.

S&F in repair 10 litre capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

S&F in repairs PVC connections 15mm size with PTMT nuts of length 450mm fixed to pipes and valves complete all as specified and directed.

S&F in repairs Vitreous China wash basin, white, flat back, size 550x400mm excluding taps, waste, chain and plug and porcelain stopper but including brackets, cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe all as specified and directed.

S&F in repairs 32mm dia; Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed including dismantling old unserviceable one complete all as specified and directed.

S&F in repair 32mm dia waste pipe of polyethylene of low or high density or PVC. 32 mm dia, suitable for vitreous china wash hand basin including taking down old unserviceable pipe complete all as specified and directed

S&F in repair 15mm dia Pillar taps, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe complete including taking down old rusted tap complete all as specified and directed.

S&F in repairs brass chromium plated bottle traps of 32 mm bore for wash basins/ urinals with inlet and outlet screwed for pipe or connections including necessary packing, union and cap all as specified and directed.

Taking up or down 15mm dia bore; steel tubing and connections, including cleaning for refixing or removal to store all as specified and directed.

Taking up or down 20mm dia bore; steel tubing and connections, including cleaning for refixing or removal to store all as specified and directed.

Taking up or down 25mm or 32mm dia bore; steel tubing and connections, including cleaning for refixing or removal to store all as specified and directed.

Supply and fixing 15mm dia bore steel tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Supply and fixing 20mm dia bore steel tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Supply and fixing 25mm dia bore steel tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Dismantling water tanks, capacity exc 250 Ltr but not exc 500 ltr and removing to store complete all as specified and directed.

Rotational moulded polyethylene water storage tanks of capacity 500 Ltrs (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I.

S&F in repairs 15 mm bore bib taps cast copper alloy with Chromium plated cruch or capston head scrwed, screwed for iron pipe or for brass ferrule and fixed complete all as specified..

S & F in repair 15mm bore stop valves chromium plated screwed down, high pressure,with crutch or capston head, screwed both ends for iron pipe or for unions fixed complete all as specified and directed

S&F Brass chromium-plated tubular towel rail, 20mm dia, 'D' type, 60cm long between flanges fixed on the wall using wooden plugs with chromium-plated brass screws and cup washers complete all as specified and directed.

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F in repair 15mm dia bore Push tap any colour high pressure of PTMT screwed for iron pipe and fixed, suitable for urinals, (Minimum weight 15mm-50gms)

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified.

Demolition, breaking and taking up from underground trenches, drain pipe (SGSW/ AC or RCC etc.) having internal dia 150mm; set in cement mortar complete all as directed. Note:- Excavation work shall be measured and paid separately under relevant items of schedule.

M & L for plain cement concrete 1:3:6 type C2, (using 40 mm graded stone aggregate) as in concrete bed to 150 mm bore drain pipe including packing under and hunching against the sides of pipes after pipe laid and tested complete all as specified and as directed. Note: The quoted rate includes the following: - (i) Thickness of bed below the barrel of pipes: 15cm (ii) Width of bed: Outer diameter of drain pipes (not of sockets/ collars) plus 30 cm (iii) The rates include for any necessary shuttering and supports to concrete and for laying beds to falls.

M&L for 150 mm bore (internal dia of pipe) reinforced concrete pipes, Class NP3 laid in trenches and jointed with CM (1:1) complete all as specified and as directed.

Excavation in trenches not exc. 1.5 mtr wide and not exc. 1.5 mtr depth for cesspits, manholes etc. and getting out soft/loose soil even in foul position complete all as specified and as direcetd.

Returning, filling including spreading leveling watering and well ramming in layers n. exc 25 cm in soft/loose soil complete all as specified and as directed.

Removing excavated soil to a distance n. exc 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as directed.

Taking down & refixing 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specifdied and directed.

S&F in repairs PVC (SWR) Branches pieces of 110mm dia double (Double Y ) equal or unequal and fixed in position including jointing complete all as specified and directed.

Supply & Fix in repairs of 110mm bore of PVC (SWR) bends any radius fixed with rubber ring joint complete all as speciifed and directed.

S&F in repairs 110mm dia, PVC(SWR) junction single (single T) equal or unequal complete all as specified and directed.

Supply & Fix in repairs PVC soil, waste and rain water (SWR) drainage pipes 110mm bore single socketed in any length with rubber ring joint fixed to wall as rain water pipe with suitable size PVC damps by maintaining 30mm clear gap between finished wall surface and pipe Including taking down pipe complete all as specified and directed.

M&L for complete removal of existing treatment of old internal decorative surface of walls and applying two coat of oil emulsion distemper, over a coat of chalk white primer including cracks filling with exterior wall care putty wherever necessary complete all as specified and directed.

M&L for complete removal of existing treatment of old external decorative surface of walls and applying two coat of cement base paint, over a coat of cement primer including cracks filling with exterior wall care putty wherever necessary complete all as specified and directed.

E/M Portion Taking down carefully copper/aluminium point wiring (Light, Fan, socket or power) complete along with fittings and fixtures such as switches, sockets, ceiling rose point, light fittings etc & making good the surface on wall complete.

M&L for point wiring using approved colour coding as per IS with 1.5 sqmm two single core PVC insulated but unsheathed FR cable, 1100 volts grade, ISI-694 marked with multistranded copper conductor and earth continuity wire with similar 1.5 Sqmm cable (Including connecting to earth dolly) drawn through ISI marked heavy duty rigid PVC concealed conduit with all accessories etc with mild steel sunken box duly, concealed in wall and having PVC modular cover plate with frame suitable for modular switch/sockets/regulators for the following: -

One light/fan point controlled by one switch one way

One 3 pin 5 Amps Socket outlet point controlled by one No one way switch on same board.

One 3 pin 5 Amps Socket outlet point controlled by one No one way switch on independent board.

All as per item No: 85 but for point wiring with 2.5 Sqmm two single core copper cable and earth continuity wire with 2.5 Sqmm single core cable for one three pin 15 Amp socket outlet point on independent board.

S&F modular switch 01 way 6 Amp, 01 module complete.

S&F modular switch 01 way 16 Amp, 01 module complete.

S&F modular Socket 6 Amp, 2 module complete.

S&F modular socket 6/16 Amp, 02 in 01, 02 module complete.

M&L in replacement modular step fan regulator 120 watt 2 module suitable for 230 volt 50 Hz supply all as specified.

S&F ceiling rose surface Bakelite 3 terminals 65X50mm, 230V including PVC Box of size 3"X3" round type.

S&F in repair for wall mounted LED 20W CRCA fitting 230 V with extruded aluminium heat sink provided for efficient heat dissipation and integral electronic driver connector block etc complete with all accessories internally prewired including necessary mounting arrangement, provision of new 3 core multistranded copper conductor of size 23/0. 193 from ceiling rose to fitting including necessary LED tube 4FT 20 W complete all as specified and directed.

S&F for lamp holder, PVC/Polycarbonate type with back plate suitable for batten fitting complete all as specified.

S&F highly efficient LED retrofit lamp 12W used as a ready replacement for fitting complete all as specified.

Taking down ceiling fans of nay size/sweep after disconnecting the wire from existing ceiling rose and re-fixing the same cleaning dust oiling, greasing including providing flexible cable from ceiling rose to connector of fan complete all as directed by Engineer-in-Charge.

S&F in repair for MCB DB TPN 4 way double door sheet metal enclosure comprising of OEM/manufacturer specified bus bar 415 Volts, 50 Hz bus bar and neutral link complete including inserting in wall complete all as specified and directed.

S&F for MCB triple pole and neutral 415 Volts, 63 Amps, 10 KA

S&F for ‘C’ curve MCB single pole & neutral 240 Volts 40 Amps.

S&F ‘C’ curve MCB SP 240 volt 6 to 30 Amp

Supply & fixing in repair of Exhaust fan with louver, steel body, size 300mm max 410 watts, minimum 1400 RPM, single phase, 230 volts including providing flexible copper cable from ceiling rose to connector of fan complete all as directed.

M&L for plate earthing in replacement of old earthing complete with galvanised mild steel plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically (in earth pit not less than 2.25 m below normal ground level) with the top edge of the earth plate at a depth not less than 1.5 m below normal ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides and incl GI earth wire 4 mm dia bolted (with GI nuts, bolts & check nuts) and riveted to earth plate at one end and connected to metallic bodies of equipment’s/ earthing test point etc at the other end, earth strip encased in and including 15 mm GI light grade pipe with all fittings from top of electrode to body of equipment fixed with and including 25x4mm iron clamps, bolts, nuts and washer and also including providing watering pipe 20mm bore GI pipe medium grade from bottom of earth pit to top of electrode complete with wire mesh funnel and earth pit in PCC 1:3:6 type C-1 using 20 mm graded crushed stone aggregate and CI cover and frame complete all specified and shown in electrical plate No 3 of SSR Part-1 including testing earth resistance and submitting test report to AGE E/M by the contractor complete all as specified and directed. Note :- (i) Rates for excavation and earthwork in any kind of soil/ strata, testing on completion, GI earth wire 4 mm and 15 mm dia light grade GI protection pipe upto 7.5 metres from earth plate is deemed to be included in the rate quoted. (ii) On testing after completion if less than 5 Ohm earth resistance is not obtained the earthling will be redone by the contractor at no extra cost the department.

Note:- The amount against the Schedule of Credit mentioned in the tender document shall be deducted from the total amount quoted against Sch 'A' while deriving the Contract Sum for Acceptance.

chronicle enterprises

M/s Shree Ganesh Traders

M/s R K Narware