GE 861 EWS-16/2022-2023

Amount

Taking down cement plaster on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors & pavings n.exc 15 cm thickness (below or above ground level), complete all as specified and directed.

Taking down chowkats or frames including shutters (without taking off shutters from the frames) not exceeding 1.50 Sqm each, complete all as specified and directed.

Taking down chowkats or frames with shutters (w/o taking of shutters from the frame) exc 1.5 but n exc n.exc 4 Sqm each, complete as specified and directed.

Dismantling plain or corrugated steel sheeting , any gauge and thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the premises,complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connection, including cleaning for refixing or removal from site, complete all as specified and directed.

Taking up or down 20mm bore steel tubing and connection, including cleaning for refixing or removal from site, complete all as specified and directed.

Demolition wall and ceiling boards (fibre, Pulp, insulation etc) or insulation board/slabs/blankets, any thickness, including cover fillets etc, complete all as specified and directed.

Dismantling timber scantling unframed 40 sq cm and over in section in any position, complete all as specified and directed.

Dismantling of timber scantling under 40 Sqcm, fixed in any position in fillet rails, posts rafters purlin etc complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding (eaves board) to wall fixed with self tapping screws as specified and directed.

2nd class hardwood, plain, solid, straight chowkats and frames, wrought, framed, worught, framed rebated on the solid, rounded of chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

35 mm thick, 2nd class hard wood (Sal/ Hollock) factory made, plain framed, panelled shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneers on both faces. The size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated, fitted to chowkats, complete all as specified and directed.

35mm thick, 2nd class hard wood (Sal/ Hollock) factory made glazed and skeleton shutters, open rebated and prepared to receive glass or gauge,etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers as specified in SSR Part-I Section-8, clause 8.24 (a) for door shutter supplying and fitted to chowkats, complete all as specified and directed.

30mm thick, 2nd class hard wood (Sal/ Hollock) factory made glazed and skeleton shutters, open rebated and prepared to receive glass or gauge,etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers as specified in SSR Part-I Section-8, clause 8.24 (b) for door shutter supplying and fitted to chowkats, complete all as specified and directed.

Aluminium powder coated door shutter side hung type on pivots alongwith hydraulic door closer with style rails ( Top, bottom & lock rail) top rails meeting style, lock rail size 48mmx44mm, top & bottom rail size 108mmx44mm, frame for chowkats size 40mmx63mm including door lock , handles 5mm thick plain glass in top and 12mm thick prelaminated particle baord (both side laminated) in bottom panel including necessary jointing cleat, glazing clips, rubber packing, snap beading, screws of suitable size etc (thickness of aluminium section shall not be less than 1.5mm), complete all as specified and directed.

Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples, complete all as specified and directed.

Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples (fixed in repairs), complete all as specified and as directed.

3mm thick figured glass,pin head type and glazing with oil putty in squares not exceeding 0.5sq.m in each pane, complete all as specified and directed.

3mm thick sheet glass ordinary quality, and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.50 Sqm in each pane, complete all as specified and directed.

100 mm long, mild steel cold rolled butt hinges, medium weight, complete all as specified and directed.

75 mm long, mild steel cold rolled butt hinges, medium weight, complete all as specified and directed.

100mm long, aluminium, anodised, barrel tower bolts of extruded section, complete all as specified and directed.

150mm long, aluminium, anodised, barrel tower bolts of extruded section, complete all as specified and directed.

150mm long, extruded aluminium alloy handles, fabricated type, anodised, complete all as specified and directed.

100mm long, extruded aluminium alloy handles, fabricated type, anodised, complete all as specified and directed.

300mm size aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and directed.

300mm size mild steel ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and directed.

10mm thick rendering on fair faces of brick or concrete surfaces in CM 1:4 finished even and smooth without using extra cement, complete all as specified and directed.

15mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:6 finished the surface even and smooth without using extra cement, complete all as specified and directed.

6mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed in ceiling flat and sloping with nails to timber frame, complete all as specified and directed.

6mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed in walls with nails to timber frame, complete all as specified and directed.

2nd class softwood plain fillets square/rectangular or triangular in section of sectional area exc 13 Sqcm but n exc 25 Sqcm, complete all as specified and directed.

2nd class softwood fillets of sectional area exc 3 sqcm but n exc 6 sqcm bull nosed, splayed, chamfered or rounded on one edge or face secured with nail or brads complete all as specified and directed.

2nd class softwood fillets of sectional area n exc 3 sqcm but bull nosed, splayed, chamfered or rounded on one edge or face complete all as specified and directed.

2nd class soft wood, as in scantling and similar work, clean sawn and timber fixed in position, complete all as specified and directed.

25mm thick PCC 1:2:4, type B-0 (using 12.5 mm graded crused stone aggregate) as in floors to recieve floor finishes, complete all as specified.

75mm thick PCC 1:3:6 Type C-2 (40 mm graded stone aggregate) as in sub-floor, sub-base, floor and pavings, etc., complete all as specified and directed.

Non-skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but not exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6, complete all as spcified and directed.

Glazed ceramic coloured tiles 450mm x 300mm x 7mm thick as in vertical surfaces such as skirting dado etc set and jointed in neat cement slurry, pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 to receive tiles, complete all as specified and directed.

Chequered coloured cement concrete tiles, glossy finished of size 300 x 300 x 25 mm thick, with grey cement and pigment, set, jointed and pointed in neat cement slurry, laid in floors, over and including 15 mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

M&L in replacement of prelaminated wooden flooring with 8 mm thick particle board planks with tounue and groove joints of size as directed over 10mm thick thermocoal sheet set with adhesive of approved make as per manufacturer's instructions over finish surface including taking out old woodern flooring, complete all as specified and directed.

Steel water tubing, 15 mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed.

Steel water tubing, 20 mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed.

S&F in repair 15mm bore bib tap with wall flange, chromium plated, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule, complete all as specified and directed.

S&F in repair 15mm bore stop valves, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union, complete all as specified and directed.

S&F in repair 15mm bore pillar tap, fancy type, cast copper alloy, with capstan head, chromium plated screwed down high pressure, with or without lettered hot/cold with long screwed shanks and fly nuts screwed for iron pipe, complete all as specified and directed.

S&F in repair brass chromium plated shower rose 125mm with or without swivel joints any size including fixing to steel pipe or union complete to walls & floors etc , complete all as specified and as directed.

S&F in repairs vitreous china squatting pan water closet, orissa pattern, size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) including cast iron 'P' or 'S' trap, jointing to flush pipe complete and making good to floor in cement concrete M-5 (1:5;10), type E-2 using 40mm graded crushed stone aggregate, complete all as specified and directed.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern), coloured, including fixing bolts, flushing cistern and flush pipe & making good to floor in cement mortar M-15 (1:2:4) type B-1 (using 20mm graded crushed stone aggregated), complete all as specified and as directed.

S&F in repair vitreous china, wash hand basin, white, flat back, of size 550mmx400mm with brackets including cutting for and pinning in ends of brackets, including 32mm waste fittings, chromium plated with long screwed shanks & fly nuts, flange end bedded in red lead cement and other end fixed, complete all as specified and directed.

S&F in repair 10 litre capacity PVC valveless, low level, synphonic action type, flushing cistern, with inlet, ball valve, float valve, handle including brackets, complete all as specified and directed.

S&F in repair vitreous china urinals, bowl type 465x355x265 mm white (back to cornor wall type), providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with flush pipe, grating and union for discharge pipe and 60mm long brass screws, pointing around urinal back in cement (exclusive of fixing pipe to flushing cistern, trap and waste pipe), complete all as specified and directed.

S&F in repair PVC connection 15mm size with brass checknuts of length 450mm, complete all as specified and directed.

S&F in repair 100mm dia outlet PVC (SWR) multi floor trap with openable grating including jointing with solvent cement, complete all as specified and directed.

S&F in repairs tubular towel rail, brass chromium plated , 20mm dia, D type 60 cm long between flanges complete all as specified and directed.

S&F in repairs central hole mixer for mixing hot & cold water screwed down for iron pipe 15mm dia bore and fixed with 450mm hose pipe, complete all as specified and directed.

S&F in repair brass body health faucet with wall hook & 1m SS braided rubber hose pipe, complete all as specified and directed.

S&F in repair fancy type corner glass shelf of size 300mmx300mm x 5.5mm thick glasss with CP railing, complete all as specified and directed.

Preparation of new plastered surfaces of walls and applying three coats of white wash, complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of cement base paint over a coat of alkali-resistant priming coat, complete all as specified and directed.

Preparation of new plastered surfaces of walls to receive 3mm thick wall care putty and applying two coats of oil bound distemper over a coat of primer, complete all as specified and directed.

Complete removal of existing treatment of walls to receive 3mm thick wall care putty and applying two coats of oil bound distemper over a coat of primer, complete all as specifed and directed.

Complete removal of existing treatment of walls and applying two coats of cement base paint over a coat of alkali resistant primer, complete all as specifed and directed.

Complete removal of existing treatment of walls and applying three coats of white wash, complete all as specifed and directed.

Preparation of old painted steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified.

Preparation of new wooden surfaces of any description not otherwise described, exc 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed.

Preparation of old painted wooden surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified.

Adil Mohammad Dijoo

M/S Sheikh and Co

BHAT CONSTRUCTIONS AND BUILFERS