Construction of Indoor Stadium of size (77.00mx55.45 m) with RCC Gallery of 552 capacity at Nagshankar, Sootea, Biswanath Chariali, Assam

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. (a) All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth,sides of foundations etc. in layers not exceeding 20cm in depth,consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m..

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials. (a) All kinds of soil

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth a) 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying in position cement concrete of specified gradeexcluding the cost of centering and shuttering - All work up to plinthlevel (a) 1½:3 (1 Cement: 1½ coarse sand (zone-III) derived fromnatural sources : 3 graded stone aggregate 20 mm nominalsize derived from natural sources)

b) 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. :- All works upto plinth level (a) Concrete of M25 grade with minimum cement content of 330 kg /cum

b) All works above plinth level upto floor V level (a) Concrete of M25 grade with minimum cement content of 330 kg /cum

Centering and shuttering including strutting, propping etc. and removal of form for a) Foundations, footings, bases of columns, etc. for mass concrete

b) Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

c) Lintels, beams, plinth beams, girders, bressumers and cantilevers

d) Suspended floors, roofs, landings, balconies and access platform

e) Columns, Pillars, Piers, Abutments, Posts and Struts

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. 5.22.6:- Thermo-Mechanically Treated bars of grade Fe-500D or more.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: (a) Cement mortar 1:4 (1 cement : 4 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. (a) Cement mortar 1:3 (1 cement :3 coarse sand)

Providing wood work in frames of doors, windows, clerestory windowsand other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). a) Sal wood

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. a) Fixed to openings /wooden frames with rawl plugs screws etc.

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.

Steel work in built up tubular (round, square or rectangular hollow tubesetc.) trusses etc., including cutting, hoisting, fixing in position andapplying a priming coat of approved steel primer, including welding andbolted with special shaped washers etc. complete. Hot finished welded type tubes

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position andapplying a priming coat of approved steel primer all complete.(Water Stagging)

62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. (a) Size of Tile 600x600 mm

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent

Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge. sqm 1718.70 Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/opening (cut outs) having area less than 0.30 sqm.The calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light reflection > 85%, non- combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity

Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using Direct mud circulation (DMC) or Bailer and chisel technique by tripod and mechanical Winch Machine all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap). Note: Truck Mounted rotary/TMR/Tubewell boring machine shall not be used. (a) 450 mm dia

Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge Note: 1. Initial and Routine Load Test shall not be carried out by Dynamic method of testing. Note: 2. Testing agency shall submit the design of loading platform for the approval of Engineer-in-charge. (a) Single pile upto 50 tonne Safe capacity a) Initial test (Test Load 2.5 times the Safe capacity)

b) Routine test (Test Load 1.5 times the Safe capacity)

Supplying, fitting and fixing in position reinforcement bars conforming to relevant IS code, for reinforced cement concrete works in piles including straightening, cleaning, cutting and bending to proper shapes and length as per specifications and drawings. The Rings should be welded with vertical reinforcements as per specified IS codes of practice.

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. (a) With material conforming to Grade-III (size range 26.5 mm to 0.075 mm ) having CBR Value-20

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. (a) 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

Providing & fixing in position Phenol bonded Bamboowood wall cladding at all height with planks of sizes 10mm thick, minimum 1800mm length and minimum 100 mm wide, in approved colour, texture and finish, having Performance Appraisal Certificate (PAC) issued by Building Materials & Technology Promotion Council (BMTPC), with necesasary profiled edges fixed with 40mm SS screws 5 nos in each tile to frame work made of second class teak wood of size 20x15 mm in centre of each tile and bottom and top of work height, 40x15mm placed at ends of each tile. The cladding shall be laid over backlayment of 1.00 mm thick expanded polyethylene foam of density 40kg/cum in two layers, first layer on wall surface before fixing wooden frame and second layer on frame under cladding. The bamboowood planks shall have minimum density of 1000 Kg/cum& minimum Hardness 1000 Kgf. with Eco friendly UV coating, all complete as per direction of the Engineer in-charge.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete (a)Ridges plain (500 - 600mm)

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement. (a) 18 mm thick

12 mm cement plaster of mix : (a) 1:4 (1 cement: 4 fine sand)

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : (a) New work (two or more coats) over and including water thinnable priming coat with cement primer

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004,Akali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. (a) New work (Two or more coats applied @ 1.43 litre/ 10sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.

Applying priming coat: (a) With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/steel works

With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel work (second coat)

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : (a) Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : a) W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required a) One urinal basin with 5 litre white P.V.C. automatic flushing cistern

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: a) White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe (a) 32 mm dia

Providing and fixing 100 mm sand cast Iron grating for gully trap.

Providing and fixing toilet paper holder : (a) C.P. brass

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (a)15 mm nominal dia Pipes

(a) 20 mm nominal dia Pipes

(b) 25 mm nominal dia Pipes

(c) 40 mm nominal dia Pipes

Providing and fixing brass stop cock of approved quality : (a)15 mm nominal bore

(b) 20 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : a) 25 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions : (i) 45 cm length (a) 15 mm nominal bore

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : (a)150 mm diameter

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) i) For fixed portion a) Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) a) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): a) With float glass panes of 4.0 mm thickness (weight notless than 10kg/sqm)

TEAK WOOD SPORTS FLOORING finished with 21 mm thick and in random length in tongue and groove shape with under frame made of pine wood runners of 70 mm x 45 mm , treated with anti termite solution and fixed on the bottom side with 19 mm thick EPDM air cushioned pads, stapled through the two wings at 350 mm x 350 mm.

Providing, fitting and fixing soap dish holdercomplete as directed and specified. (i) Jaquar Make-Model-ACN-1131N

Providing, fitting and fixing Liquid soap dispenser and liquid soap container complete as directed and specified. (i) Jaquar Make-Model-ACN-1137N

Providing, fitting and fixing CP towel rail complete as directed and specified. (i) Jaquar Make-Model-ACN-1101S

Providing, fitting and fixing Chrome Plated towel rack complete as directed and specified. (a) Jaquar Make-Model-ACN-1181FS

Providing, fitting and fixing Chrome Plated towel ring complete as directed and specified. (a) Jaquar make -ACN-1121BN

Supplying fitting and fixing Pipes with all necessary fittings in exposed or in trenches including trenching and refilling the same etc complete as directed B) uPVC pipe with uPVC fittings ( Using uPVC high pressure pipe) (Using SUPREME/ PRINCE/ SFMC/ FUSION brand pipe) (a) 110mm diameter

(b) 75mm diameter

Supplying, fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining ,fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified. (a) 110mm dia.

(b) 75 mm dia.

Supplying fiting and fixing 87.5 degree PVC bend with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. (a) 110mm dia.

(b) 75mm dia.

Supplying fiting and fixing 45degree PVC bend of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. (i) 110mm dia.

(ii) 75 mm dia.

Supplying fiting and fixing PVC Plain single tee of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. (i)110mm dia.

(ii) 75 mm dia.

Supplying fitting and fixing C.P. bib cock 15mm dia of approved brand directed and specified. (G.I. & C.P pipes will be measured separately) C.P.2-way bibcock with wall flange-Jaquar make -FON-40041

Supplying fitting and fixing shower with arm as per direction of Engineer-in-charge-Jaquar make -OHS-1843

Supplying fitting and fixing chrome plated (C.P.) concelead stop-cock of approved brand and size as mentioned below as directed and specified-Jaquar make -FON-40053

Providing fitting and fixing vitreous china squatting plate urinal with automatic flushing cistern with standard flush pipe and CP brass spreader and brass unions, etc. complete including painting of fittings and brackets, cutting and making good the walls & floors wherever required. (A) Parryware Make

Supplying and fitting fixing C.P. pillar cock of 15mm dia of approved brand as specified and directed.: Jaquar make -FLR-5011N

Supplying fitting and fixing LONG BODY C.P. bib cock 15mm dia of approved brand directed and specified. -Jaquar make -COT-23021

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with piano type switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. Group B

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. Group B

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

2 X 10 sq. mm + 1 X 6 sq. mm earth wire

4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 4 way (4 + 12), Double door

8 way (4 + 24), Double door

12 way (4 + 36), Double door

Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as reqd. (Make:- Orient /USHA / Bajaj/Crompton/Polar)

Supplying, Installation of following size metallic body heavy duty, double ball bearing, 900 RPM exhaust fan with inbuilt louvers in the existing opening, including making hole to suit the size of the above fan, making good the damages, connection, testing, commissioning etc. as required. (Make: USHA / Orient / POLAR/ BAJAJ) a) 300 mm sweep

b) 250 mm sweep

Supplying & Fixing of LED batten/ rail for LED fitting of minimum lumen output 2000 Lumen & luminious efficacy 100 lumen / watt & above made of Engineering plastic with white acrylic diffuser, including connection with 1.5 sq.mm. FR LS PVC insulated, copper conductor, single core cable and earthing etc. as reqd. (Make : Crompton - LT8-20-865-2 / Havells - LUMILINEBS20WLED865SPCWH or Equivalent in Bajaj / Phillips / Wipro)

Supplying and fixing 36 watt surface/Recess mounted LED fitting made of CRCA aluminium housing with high transmission acrylic diffuser (size- 4' x 1'), aesthetically designed flat panel which provides soft-light and glare free symmetrical illumination including connections using 1.5 sq. mm. FRLS PVC insulated, copper conductor, single core cable and earthing etc. as reqd. (Make : Bajaj /Havells /Philips /Crompton)

Supplying, Installations, testing & commissioning of surface/Recess mounting Square type (2' x 2') Decorative 36W LED type fitting with driver made of CRCA housing and acrylic diffuser complete etc. i/c connections etc. as reqd. (Make :- Bajaj - BZSSQL 36W LED WHi or similar make of Havells/ Phillips / Surya / Wipro)

Supplying and fixing of 12 watt LED Surface / Recess mounting downlight luminairies Mmade of aluminium die-cast body, drop down PC diffuser with electronic driver and suitable for 230 V, 50 Hz, AC supply i/c testing, commissioning etc. as reqd. (Make : Crompton - LCDSPLN-12-CDL / Havells - ENDURANEOHESURFACEDLS15WLED857S or Equivalent in Bajaj / Surya / Phillips / Wipro)

SITC of energy efficient 25 Watt LED street light iuminaires with pressure die cast housing along with prismatic polycarbonate diffuser and LEDs with secondary optics and IP 65 protection i/c providing and fixing of suilable bracket for fixing the luminaires, connection with 1.5 sq. mm FR LS PVC insulated copper conductor single core cable testing etc complete as required. (Make : Havells:ENDURAPEARLSL25WLED757SASYTOPCMP / Crompton : LST-25-CDL-M or Equivalent in Bajaj / Wipro / Phillips)

Supplying and fixing 10 watt LED bulkhead luminaires IP65 protection energy efficient suitable for 230volt, 50Hz ac supply complete as required. (Make: Bajaj - BIBWP 10W LED or equivalent make of Havells/Crompton /Surya / Wipro / Phillips)

Supplying, installation, testing and commissioning of LED street light luminaire made out of pressure dia cast housing with epoxy powder coated dark graphite gray colour finished and prismatic polycarbonator cover with lamp having minimum lumen output 4500 lumen, minimum luminous efficacy 100 lumen/watt with 1.5 sq.mm FR LS PVC insulated copper conductor single core cable testing etc complete as required. (Make: Havells -ENDURAPEARLNEOSL45WLED757PASYTOPC or Equivalent Bajaj / Crompton / Surya / Wipro / Phillips)

SITC of 35 Watt energy efficient LED post top lanterns with efficient light dustribution made of cast aluminium with decorative polycarbonate diffuser with IP 65 protection and lamp having minimum lumen output 3500 lumen, minimum luminous efficacy 100 lumen/watt i/c connection with 1.5 sq. mm FR LS PVC insulated copper conductor single core cable testing etc complete as required. (Make : Havells - CORALPT35WLED757PSYMTOPC or Equivalent in Bajaj / Crompton / Surya / Wipro / Phillips)

Supplying & Erection of hot dipped galvanised 8 mtr height octagonal pole. The pole shall also be provided with hindged / clained flush door of approx 500mm length at an elevation of 1m from the base plate with proper strengthening to the cutout of the door opening. Each pole shall be complete with a Bakellite sheet complete with DIN rail, 10 amps, 10 kA SP MCB, Screwless DIN mounting Connectors suitable for 16 sq.mm. terminations complete with DIN bar, shorting links, end locks etc as required (Wago / Pheonix make) and 3 x 1.5 sqmm FRLS PVC isulated copper conductor single core cable from junction box to the luminaire complete including 1 No. 3 (three) terminations with insulated copper lugs etc as required.The pole shall be with suitable size of GI base plate, 600mm long 'J' type GI foundation bolts of min. 20mm dia each with three GI nuts and two GI washers (EN.8 grade) etc complete as per drawing. The pole shall have a minimum OAF of 130mm at bottom and 70 mm at top. The pole shall have a minimum section thickness of 3 mm. The pole shall be fabricated in a single section and shall be provided with necessary gaskets of 12mm thickness at the bottom. The installation shall include making RCC foundation suitable for a soil bearing capacity of 5 Ton/ Cum (Design & drawing must be approved by Engineer-in-Charge).

Supplying following size XLPE insulated and PVC sheathed armoured power cable of 1.1 KV grade conforming to IS 7098 (Part 1) 1988 and ammended up to date as required. (Make : Polycab / Havell's / Richa / KEI / RR Kabel) i) 4 X 16 sq.mm.

ii) 4 X 10 sq.mm.

iii) 2 x 10 sq.mm

Laying of one number XLPE insulated and PVC sheathed armoured aluminium conductor power cable of 1.1 KV grade conforming to IS- 7098 part-I/ 1988 of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. a) Upto 35 sq.mm.

(i) Incoming: Fabrication, supplying, installation, testing and commissioning of floor mounted, Indoor type metering panel board suitable for 415 volt, 3 phase, 4 wire, 50 Hz AC supply, compartmentalized, depth not less than 400 mm made of 2 mm thick CRCA sheet steel, cleaning, processing, & finishing complete with 7/8 tank process for powder coating in approved shade of welded construction with necessary stiffner, suitable compartments for mounting of switch gear and other accessories with hinged type door at front and back side with locking arrangement, with 200 amps capacity 4 strips aluminium bus bar of high conductivity with DMC/SMC bus bar support, connection and inter connection of switch gears, proper gasketing adequate ventilation arrangement, entire panel shall have a common aluminium earth bar of size 50mm x 5mm at the rear, control wiring with 1.5 sq.mm. FRLS insulated copper conductor S/C cable, cable alleys, individual cable gland plate (3mm thick), terminal block for incoming and each outgoing, and entire panel shall be mounted on suitable MS channel iron as reqd. (General arrangement and schematic diagram to be approved by the department before start of fabrication) (Make - CPRI Approved make)(For T-II -& T-III -blocks) (i) Incoming: (i) 125 Amp FP Switch Disconnector Fuse Unit with HRC Fuses (L&T / Havells / Indo-Assian/ Legrand /Schnider) --- 1 No. (ii) Bus Bar (a) 4 strip Aluminium 200Amps rating (iii) Outgoing: (a) 40 Amps DP MCB--- 6 Nos. (a) 40 Amps SP MCB--- 4 Nos. (b) (5-30) Amps Single phase Electronic meter with counter display---- 6 Nos. e) Phase Indication LED lamp for each phases with 3 Nos. 2A (10KA) SP MCB -1set

Fabrication, supplying, installation, testing and commissioning of floor mounted, Indoor type metering panel board suitable for 415 volt, 3 phase, 4 wire, 50 Hz AC supply, compartmentalized, depth not less than 400 mm made of 2 mm thick CRCA sheet steel, cleaning, processing, & finishing complete with 7/8 tank process for powder coating in approved shade of welded construction with necessary stiffner, suitable compartments for mounting of switch gear and other accessories with hinged type door at front and back side with locking arrangement, with 200 amps capacity 4 strips aluminium bus bar of high conductivity with DMC/SMC bus bar support, connection and inter connection of switch gears, proper gasketing adequate ventilation arrangement, entire panel shall have a common aluminium earth bar of size 50mm x 5mm at the rear, control wiring with 1.5 sq.mm. FRLS insulated copper conductor S/C cable, cable alleys, individual cable gland plate (3mm thick), terminal block for incoming and each outgoing, and entire panel shall be mounted on suitable MS channel iron as reqd. (General arrangement and schematic diagram to be approved by the department before start of fabrication) (For T-IV & T-V) (i) Incoming: (i) 160 Amp FP Switch Disconnector Fuse Unit with HRC Fuses (L&T/ Havells /Indo-Assian/ Legrand /Schnider) - 1 No. (ii) Bus Bar (a) 4 strip Aluminium 200 Amps rating (iii) Outgoing: (a) 40 Amps SP MCB -- 4 Nos. (a) 40 Amps TP MCB --2 Nos. (b) (10-40) Amps Threee phase Electronic meter with counter display--2 Nos. e) Phase Indication LED lamp for each phases with 3 Nos. 2A (10KA) SP MCB - 1 set

SAILAJA COMMERCIAL CONSTRUCTION PVT LTD