Renovation of Ist floor and External Deveplopment at NEERI Delhi Zonal Center Naraina New Delhi

Amount

Carriage of material by mechanical transport including loading, unloading and stacking out side municipal limits upto lead of 20 KM . Lime, morum, building rubbish .

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

supplying and Filling excavated earth ( excluding rock ) in trenches, plinth,sides of foundation etc. in layers not exceeding 20 cm in depth,consolidating each deposited layer by ramming and watering,lead up to 50m and lift upto 1.5m.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : a) 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : a) 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Providing and laying in psition specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement- all work up to plinth level: 1 : 1.5 : 3 ( 1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for all heights :

Columns, Pillars, Piers, Abutments, Posts and Struts

Brick work with common burnt clay FPS (non modular) bricks of class designation 7.5 in foundation and plinth in : cement mortar 1:4 (1 cement : 4 coarse sand)

Brick work with common burnt clay FPS (non modular) bricks of class designation 7.5 in super structure above plinth level up to floor V level in all shapes and sizes in : cement mortar 1:4 (1 cement : 4 coarse sand)

Half brick masonry with common burnt clay F.P.S ( non modular ) bricks of class designation 7.5 in superstructure above plinth level upto floor V level. Cement Mortar 1:4( 1 cement : 3 coarse sand)

Extra for providing and placing in position 2 nos. 6mm dia M.S. bars at every third course of half brick masonry.

Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished) machine cut for lift lobby cladding, kitchen platforms, vanity counters, window sills , facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edge to give high gloss finish etc. complete at all levels. Granite of any colour and shade.

area of slab up to .50 sqm

area of slab over .50 sqm

Providing edge moulding to 18mm thick marble stone counters, vanities etc ......... EIC. Grenite work.

Extra for fixing marble / grenite stone over and above corresponding basic item in facia and drops of width upto 150mm with epoxy resin based adhesive , including cleaning etc. Complete.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fastener of required dia & length ( hold fast lugs or dash fastener shall be paid for seperately ) : Second class teak wood

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters : 30 mm thick including ISI marked stainless steel but hinges with necessary screws :

Extra for providing lipping with 2nd class teak wood battens 25mm minimum depth on all edges of shutters (overall area of door shutter to be measured)

Providing and fixing plywood 4 mm thick, one side decorative veneer conforming to IS: 1328 (type-1), for plain lining / cladding with necessary screws, including priming coat on unexposed surface with Decorative veneer facings of approved manufacture

Providing and fixing hard drawn steel wire fabric 75x25 mm mesh of weight not less than 7.75 Kg per sqm to window frames etc. including 62x19 mm beading of second class teak wood and priming coat with approved steel primer all complete.

Providing and fixing IS : 3564 marked aluminium extruded section body tubular type universal hydraulic door closer with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling

channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, Galvanised M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each with zinc coating of 120 gms/sqm(both side inclusive)) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.75 mm overall thickness partition with 12.5 mm thick double skin fire rated Glass Reinforced Gypsum (GRG), plaster board conforming to IS: 2095: (part 3) 1996 (Board with BIS Certification marks).

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.00mm thick

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) :Medium shade pigment using 50% white cement, 50% ordinary cement

Providing and laying polished Vitrified Dual Charged tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved brand and manufacturer, in all colours & shade, in skirting , riser of steps , laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS 15477 in average 6mm thickness including grouting of joints. Size of tile upto 600x600mm

Providing and laying polished Vitrified Dual Charged tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved brand and manufacturer, in all colours & shade, in skirting , riser of steps , laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS 15477 in average 6mm thickness including grouting of joints. Size of tile upto 800x800mm

Providing and laying Vitrified Dual Charged tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints.Size of Tile 600x600 mm

Providing and laying Vitrified Dual Charged tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints.Size of Tile 800x800 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.(approved make superem/phenolux or equivalent.(Pressure 6kg sqcm)

Single tee with door110x110x110 mm

Bend 87.5°(PVC Elbow)110 mm bend

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction,

including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS Certification marks)

Providing and fixing tiled false ceiling of approved materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings,fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.

Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending.

12mm cement plaster of mix: 1:4 (1 cement :4 coarse sand)

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete

Applying one coat of cement primer of approved brand and manufacture on wall surface :Cement Primer

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture.

Wall painting with acrylic emulsion paint ,having VOC (volatile organic compound ) content less than 50 grams/ litre of approved brand and manufacture including applying additional coats of whereever required, to achive even shade and colour.Two Coats

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade. One or more coats on old work

Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 metres lead. With cement mortar 1:4 (1cement :4 coarse sand)

Providing and fixing 150mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete

Demolishing Brick work manually / by machanical means including stacking of servicable material and disposal of unserviceable material within 50 metre lead as per direction of EIC. In cement mortar

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metre lead for thickness of tile 10mm to 25mm

Dismantling wooden boardings in lining of walls partitions thickness upto 10mm to 25mm

Dismantling cement asbestos, gypsum ceiling, wall /Aluminium stripes ceiling or other hard board ceiling or aluminium and wooden partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead.(Note: Nothing extra will be paid for shifting / loading /unloading of the dismantaled material from third floor to ground floor of the office building.)

Dismantling GI pipes ( external work ) including excavation and refilling trenches after taking out the pipes , mannually by machanical means including stacking of pipes within 50metres lead as per direction Engineer in charge. 15mm to 40 mm nominal bore

Dismantling of flushing cistern/wash basin /EWC of any size including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead.

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron 'Y' shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Providing and fixing white vitreous china flat back half stall urinal of size 590x375x390 mm with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required .

Providing and fixing 8mm dia C.P./ S.S. Jet with flexible tube upto 1 metre long with S.S triangular plate to european type W.C. of Quality and make as approved by Engineer-in-charge.

Providing and fixing CP brass toilet paper holder

Providing and fixing PTMT Bottle Trap for Wash basin and sink. Bottle trap 31mm single piece moulded with height of 270mm, effective length of tail pipe 260mm from the centre of the waste coupling 77mm breadth with 25mm minimum water seal, weighing not less than 260gms.

Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour. weighing not less than 105 gms.

Providing & Fixing PTMT towel rail complete with brackets fixed to wooden cleats with C.P. brass screws with concealed fittings arrangements of approved quality colour. 600mm long towel ril with total lenghth of 645mm, width 78mm and effective height of 88mm, weighing not less than 190 gms. dash fastener drilling etc. complete with All respect as per direction of Engineer in Charge

Providing and fixing PTMT 15 mm Urinal spreader size 95x69x100 mm with 1/2" BSP thread and shapes, weighing not less than 60 gms.

Providing and fixing infrared sensor for urinal having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side,including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-incharge.( Make : Cera/Jaquar)

Providing and fixing Chlorinated polyvinyl Chloride (CPVC) pipes , having thermal stability for hot and cold water supply , including all CPVC plain & threaded fittings , i/c fixing the pipe with clamps at 1m spacing . This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge. Concealed work , including cutting chasis and making good the walls etc .

15mm nominal bore outer dia pipe

32mm nominal bore outer dia pipe

Providing and fixing C.P. brass long body bib cock of approved quality and of approved make conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore ( Make : Cera / Jaquar/Parryware)

Providing & Fixing C.P. brass angle valve for basin mixer and geyser points of approved quality and of approved make conforming to IS 8931 - 15 mm nominal bore ( Make : Cera/ Jaquar/Parryware)

Providing and fixing C.P brass extention nipple ( size 15mmx50mm) of approved make and quality as per direction of EIC.

Providing & Fixing PTMT grating of approved quality and colour, Circular type 100 mm Dia. Nominal bore

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and paneling to be paid for separately) :

For fixed portion Powdwer coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows' & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost pvc neoprene gasket required (Fittings shall be paid for separately). Powdwer coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) ( Make : Saintgobain/Modi Guard/AIS)

Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side,having 12 mm air gap, including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc. as per specifications, drawings and direction of Engineer-in-charge complete.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand & manufacture including providing & fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete. as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately). ( Make : Saintgobain/Modi Guard/AIS)

Providing and fixing Ist quality ceramic glazed (digitally printed, DGVT) wall tiles of size up to 600x450mmconforming to IS : 15622 (thickness to be specified by the manufacture ) of approved make in all colours, shades except burgundy , bottle green, black of size 600x300mm (digital printed) as approved by Engineer-in-Charge in walls, skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.( Make : Orient/Kajaria/Nitco)

Providing and laying Ceramic glazed floor tiles upto size 450x450 mm(digital printed) (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigment etc., complete. ( Make : Orient/Kajaria/Nitco)

Providing and fixing white / Ivory vitreous china wall hung type water closet with seat and lid, 10 litre low level white vitreous china flushing cistern & CP flush bend with fittings & CI brackets , including painting of fittings and brackets,cutting and making good the walls and floors where ever required. all compete as per the direction of Engineer in Charge. ( Make : Cera /Jaquar / Parryware)

Providing and fixing under counter white / Ivory wash basin of size 560mm x 470 mm with C.I./M.S. brackets, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required. ( Make : Cera /Jaquar / Parryware)

Providing and fixing CP brass sensotronic sensor faucet for washbasin with 175mm extension body. All complete as per direction of EIC. ( Make : Cera /Jaquar / Parryware)

Providing and fixing of CP brass Wall Mixer. All complete as per direction of EIC. ( Make : Cera /Jaquar / Parryware)

Providing and fixing of CP brass Three way Swan Neck tap for laboratory use. All complete as per direction of EIC. ( Make : Cera /Jaquar / Parryware)

Providing and fixing of CP brass washbasin Mixer. All complete as per direction of EIC. ( Make : Cera /Jaquar / Parryware)

Providing & Fixing hand Spray (Health Faucet) with 8mm dia 1m long PVC tube of approved brand as per direction of Engineer-in-charge. ( Make : Cera /Jaquar / Parryware)

Providing and fixing specially designed superior quality and fancy looking mirror with 6mm thick backing ply and frame fixed to rawl plugs with CP brass screws complete in all respect. ( Make : Saintgobain/Modi Guard/AIS)

Providing and laying polished Chemical Resistant Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved brand and manufacturer, in all colours & shade, in skirting , riser of steps , laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS 15477 in average 6mm thickness including grouting of joints (payment for grouting of joints to be made seperatly). Size of tile 600x600mm ( Make : Orient / Kajaria )

Providing and laying polished Chemical Resistant glazed Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved brand and manufacturer, in all colours & shade laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS 15477 in average 6mm thickness including grouting of joints (payment for grouting of joints to be made seperatly). Size of tile 600x600mm ( Make : Orient / Kajaria )

Providing and fixing 12 mm thick frameless toughened glass partition of approved brand and manufacture, including providing & fixing top & bottom fixings arrangement fittings all complete as per direction of Engineer -in -Charge. ( Nothing extra will be paid regarding fittings etc. ) ( Make : ModiGuard / SaintGobain / AIS )

Providing and fixing 12 mm thick toughened glass on aluminium partition of approved brand and manufacture, including providing & fixing top & bottom fixings arrangement fittings all complete as per direction of Engineer -in -Charge. ( Nothing extra will be paid rgarding fittings etc. ) ( Make : Saintgobain/Modi Guard/AIS)

Providing & Fixing 12mm thick MDF pannel board with laser cut 2D & 3D designs of size up to size (8 ft. x 4 ft), finished with PU paint and fixed with nails/screws on walls , partitions and wooden partitions,ceilings etc. - Complete. As per direction of engineer in charge ( Make : Centuary / Greenlam /Formica )

P& F designer frosted film on toughened glass partition and doors as per required pattern complete as per direction of Engineer-in-Charge . ( Make : 3M / Garware )

Providing &Fixing 18/19 mm thick commercial wooden board ( termite proof) over the partition ,walls fixed with nails/screws and for making of cupboards, Overhead storage etc.complete with all respect and as per the direction of the Engineer in Charge.

Providing & Fixing Vertical blinds 100mm with soft textured acrylic of any shade of approved quality and approved make,colour on the existing windows including cost of all materials such as brackets,plugs, screws etc. complete in all respect as per the the direction of Engineer in Charge. ( Make : Vista / Mac )

Providing & Fixing Zebra blinds 100mm with soft textured acrylic of any shade of approved quality and approved make ,colour on the existing windows including cost of all materials such as brackets,plugs, screws etc. complete in all respect as per the the direction of Engineer in Charge. ( Make : Vista / Mac )

Providing and fixing double action hydraulic floor spring IS : 6315 marked, for doors including cost of cutting floors as required, embedding in floors and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With stainless steel cover plate. (Make : Ozone / Dorma )

P/F Set of of SS handles of 450 mm to 600 mm long for doors match with existing door. (Make : Ozone / Dorma )

Providing fixing SS glass door lock with strike box (without cut out) for frame less toughened glass doors match with existing door fittings with SS screws etc. complete as per direction of Engineer-in-charge (Make : Ozone / Dorma )

Providing & Fixing 12mm thick Designer MDF pannel board with PU paint finishing - Complete. As per direction of engineer in charge ( Make : Centuary / GreenLam / Formica )

Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight Mineral Fiber false ceiling tiles of approved texture of size 600 x 600 mm in true horizontal level, suspended on concealed inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size panel to from Concealed grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel sheet with the help of rawl plugs and laying 20 mm thick densified edges Mineral Fiber ceiling tiles of approved texture in the grid, including, cutting/ making opening“for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size as per manufacture's specifications fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips. For all heights, as per specifications, drawings and as directed by Engineer-in-Charge. Note :- Only Mineral Fiber false ceiling area will be measured from wall to wall. No deduction shall be made for opening (cut outs) having area less than 0.30 sqm.The Mineral Fiber ceiling tile shall have NRC value of 0.50 (Minimum), light reflection > 85%, non- combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity <0.043 w/mK.

Providing & Fixing reflective type Sun control film of Garware or its equivalent make of approved quality colour as per the direction of Engineer in Charge including fixing into the existig windows/ door glass complete with all respect as per the the direction of Engineer in Charge.

Providing and fixing automatic sliding door system (in toughened glass door shutters upto 4m wide opening) with all fittings , fixtures, sensors etc all complete as per direction of EIC. (Make : Ozone / Dorma )

Providing and fixing bright finished SS floor door stopper for toughened glass doors with necessary screws etc complete.(Make : Ozone / Dorma )

Providing and fixing bright finished 12mm SS strip of approved make for partitions and grooves of wall cladding etc with necessary screws etc complete.

Providing and applying mirror finish melamine polishing on wood work (two or more coats so as to achieve mirror finish) complete in all respect :

Providing and fixing Stainless steel connection pipe with brass unions : 45 cm length , 15 mm nominal bore

Providing and fixing on wall face un plasticised Rigid PVC soil waste/drain/waste water pipes conforming to ISI marked approved make supreme/phenolux or equivalent including jointing with seal ring conforming to relevent IS including 10 mm gap for thermal expansion.(Pressure 6kg/sqcm)110 mm diameter

Providing and fixing SS tower bolts ISI marked to required colour or shade with necessary screws etc. complete : upto size 300x10mm (Make : Ozone / Dorma )

Providing and fixing SS door handles, ISI marked, transparent or dyed to required colour or shade, with necessary screws etc. Complete up to size : 250 mm (Make : Ozone / Dorma )

Providing and fixing SS window handles, ISI marked, transparent or dyed to required colour or shade, with necessary screws etc. completeup to size : 125 mm (Make : Ozone / Dorma )

Providing and fixing SS Sliding door bolt for doors All complete as per direction of EIC. (Make : Ozone / Dorma )

Providing and fixing SS letters of size upto 300mm and a CSIR Logo upto dia upto 300mm

Making opening by core cutting of RCC slab including cutting of reinforcement by diamond core cutter in cicular, rectangular or square shapes including disposal of dismanteled material all complete as directed by EIC.( Note: payment of core cutting will be made on the basis of per cm linear length.

Providing and laying TAC tiles of size 300x300x45mm having water absorption less than 0.5% of approved make in all colours and shades in outdoor floors such as footpath, courtyard,multi modals location etc.,laid on 20mm thick based of cement mortar 1:4 ( 1 cement : 4 coarse sand ) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-charge.

Providing and fixing L-shape Toilet partition and urinal partitions made with 12 mm thk laminated particle board with all necessary accesories all complete as per direction of EIC. Refer Annexure-5

Providing and fixing of korean stone of desired colour on reception table ( area of korean stone is upto 3.8 sqm for reception table )and washbasin counters of toilets (i.e. Area of korean stone is upto 1.00sqm for ladies toilet and area of Korean stone upto 1.6 sqm for Gents toilet ) with complete finish of edges all complete as per direction of EIC.Refer Annexure-5

Fabrication and fixing of Reception Table of size upto 2700mmx1500mmx750mm with 03 no lockable drawers complete with all material where ever required i.e 18mm thick commercial ply of approved brand duly covered with 1.5 mm thick laminate of approved make and of any colour and shade ,telescopic channels, 6mm ply , locks, handles, MDF Jali and MDF Board with smooth PU/Duko Paint finish and with mirror finish malamine polish where ever required in table etc.all complete as per approved drawing( Refer Annexure-4,Drawing No. 1) and as per direction of engineer incharge.

Fabrication and fixing of decorative Back side panel of size upto 2400mmx2700mm. Made with 100mmx100mmx 2700mm wooden rafter duly finished with 4mm thick veneer of approved brand with mirror finish malamine polish complete with all material where ever required i.e 18mm thick commercial ply of approved brand duly covered with 1.5 mm thick laminate of approved make and of any colour and shade ,telescopic channels, 6mm ply ,locks ,handles, MDF Jali and MDF Board with smooth PU/Duko Paint finish and with mirror finish malamine polish where ever required etc.all complete as per approved drawing( Refer Annexure-4 Drawing no.2) and as per direction of engineer incharge.

Fabrication and fixing of decorative Display unit at Reception area of size upto 3185mmx2700mmx600mm. with toughened Glass door shutters complete with all material where ever required i.e 18mm thick commercial ply of approved brand duly covered with 1.5 mm thick laminate of approved make and of any colour and shade ,telescopic channels, 6mm ply, locks ,handles , 4mm thick veneer, glass 12mm thk toughened ,MDF Jali and MDF Board with smooth PU/Duko Paint finish and with mirror finish malamine polish where ever requiredetc.all complete as per approved drawing( Refer Annexure-4 drawing no.3 ) and as per direction of engineer incharge.

Fabrication and fixing of decorative Panel for LED ( LED is not included ) in meeting room with 2nos storage unit. Size of central panel is upto 2700mmx3300mm and storage unit size is upto 1200mmx2700mm complete with all material where ever required i.e 18mm thick commercial ply of approved brand duly covered with 1.5 mm thick laminate of approved make and of any colour and shade ,telescopic channels,locks ,handles, 6mm ply , 4mm thick veneer, glass 12mm thk toughened ,MDF Jali and MDF Board with smooth PU/Duko Paint finish and with mirror finish malamine polish where ever required etc.all complete as per approved drawing(Refer Annexure-4 drawing no. 4) and as per direction of engineer incharge.

Fabrication and fixing of decorative storage unit complete with all material where ever required i.e 18mm thick commercial ply of approved brand duly covered with 1.5 mm thick laminate of approved make and of any colour and shade ,telescopic channels, 6mm ply ,locks ,handles 4mm thick veneer, glass 12mm thk toughened ,MDF Jali and MDF Board with smooth PU/Duko Paint finish and with mirror finish malamine polish where ever required etc.all complete as per approved drawing ( Refer Annexure-4 drawing no. 5 A and 5B ) and as per direction of engineer incharge.

Taking out and refixing of existing door shutters after cutting the door from bottom and necessary repairs

Providing and fixing under counter laboratory Sink of size 560mm x 470 mm of make CERA, parry ware or eqivalent with C.I./M.S. brackets, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required

Providing & Fixing 8 mm thick laminated wooden flooring ( AC-4 ). including preparation of surface, making the surface properly levelled with approved chemica,PVC sheet and backing material complete with all respect as per manufacturers specifications and as per the direction of Engineer -in -Charge. ( Make Euro / Vista )

Providing & Fixing Laminated wooden skirting complete with all respect as per the direction of Enginer in Charge. ( Make Euro / Vista )

Fabrication of store room by using existing aluminium fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, all complete as per architectural drawings and the directions of Engineer-in-charge. the glasses and the almunium under BOQ item no. 65 and 46 will be reused after cutting as per required size.

Supplying of Labour for shifting of office and lab furniture to basement, Nothing extra will be paid for shifting of material upto 4 floors.

Finishing walls with textured exterior paint of required shade: New Work( Two or more Coats applied @3.28 Ltr/ 10 sqm) over and including priming coat of exterior primer applied @2.20 KG/10 sqm.

Providing and fixing CP brass over Head shower of make all complete as per direction of EC ( Make : Cera/Jaquar/Parryware )

Providing and fixing of CP wall mounted towel rack all complete as per direction of EC ( Make : Cera/Jaquar/Parryware )

Providing and fixing of CP soap dish all complete as per direction of EC ( Make : Cera/Jaquar/Parryware )

Sub Head - II : Buy Back

Buy back the dismantalled existing Aluminium windows & angle frames of windows of asorted sizes and taking out of CSIR-NEERI Naraina building premises including loading unloading and transportation etc complete. The weight of the aluminium I will be ascertained on the basis of the difference of loaded vehicle and the tare weight of the vehicle after weighing the same at weigh Bridge (Dharm kaanta). The charges of weighing will be borne by the contractor. (Note: Nothing extra will be paid for shifting / loading /unloading of the dismantaled material from third floor to ground floor of the office building.)

Sub Head -III : Furniture

Providing and placing of panel & tile based modular workstations of size 1500 mm(W1) x 1500 mm(W2) x 600mm(D) x 1200mm(H) which are GRIHA compliant and as per BIFMA standards, with partition thickness of 50 mm thick including powder coated aluminium trims and supported on Legs for better air circulation and helps in keeping floor clean. The product should be complete and as per apprroved sample and as per the direction of Engineer-In-charge. Panels Construction - Each panel consists of Vertical extrusions 2Nos and Horizontal extrusions made of 1.2mm thick aluminium with duly powder coated at every division of tile/block. Each panel have Bottom frame fabricated for 50 mm panel comprises of L-channels made of 2mm thick CRCA steel (IS: 513), formed plates of 3mm thick HR steel (IS: 2062) & ERW steel tube of size 35x15x1.6mm thick in oval cross section (IS: 7138) welded together. The complete bottom frame shall be powder coated with an average of 50-60 microns thickness of epoxy powder coating. The Bottom Frame is bolted with the Upright verticals. Each Panel is provided with 2Nos Legs of height 120mm are fixed at the bottom frame of the panel. Legs are fabricated by CO2 welded MS Tube of section 38mm x 25mm (IS: 7138 ERW Tube, 38mm x 25mm x 16bg)

with the base plate of the MS plate of 35x22x5mm (IS: 2062, 5mm HR) over which an M8 Leveler is fitted which allows for adjustment of the height by 50mm. It will be coated with 45-50micron thickness of epoxy powder coating. Each Panel consists of 2Nos Intermediate blocks. In a 50 mm Thick panel intermediate block shall comprise of 38mm thick paper honeycomb with 3mm MDF on each sides and 0.6mm decorative laminate on both sides. Particle board framing shall be used n outer boundary of these blocks as well as intermediately at certain locations forming conduit for passing cables. These blocks will be located in the middle bands of the panels made out of a composite construction of MDF and paper honeycomb. Each Panel consist of TOP TILES/SPLIT TILES. These tiles shall be slid in to the panels from top before fixing the top horizontal. These tiles shall be supported from top & bottom side with clips made from PP co polymer fitted in horizontal extrusion. In case of split tiles it shall be offered in Fabric magnetic tiles, Whiteboard tiles. Each Panel consists a BOTTOM TILE.

These bottom tiles shall be press fitted on to the assembly frame of the panel with the help of snap on clips made of nylon-66 and support clips made from PP polymer. All partitions and side panels have levelling screws for adjustment in case of Uneven floor to take care of +/- 40 mm of uneven flooring. Tile Finishes : a FABRIC MAGNETIC TILES: Fabric magnetic tiles shall be fabric upholstered metal tiles in 0.6 mm thick G.I. Grade O as per IS: 277. The fabrics shall be upholstered with adhesives.

• FABRIC TACK TILES: Fabric tackable tiles shall be upholstered metal tiles in 0.6mm thick G.I. grade O as per IS: 277, with P.E. foam in the tile for tackablity. The fabric shall be upholstered with adhesives.• WHITE BOARD TILES : White board tiles shall be made of 8.0 mm thick particle board conforming to IS: 12823 laminated with 0.6mm thick white glossy high pressure laminate on outer side & 0.6mm backing laminate on inner surface and will be having all its edges with minimum 0.5 mm thick PVC edging. Aluminium Trims : The top trims and end trims for 50 mm shall be made from aluminum extrusion. All kinds of extrusions for 50 mm shall have average wall thickness of 1.2 mm & having finish of powder coating. Top trim in 50 mm thick panel shall be press fitted on the horizontal extrusion, it shall be slide

fitted with the help of top trim connector made from PP copolymer 3530 grade. End trim for 50 mm thick panel shall be slide fitted with the help of end trim connector made from 2.0mm thick M.S. CRCA Grade D as per IS: 513. End trim for 22.8 mm thick panel shall slide with the help of end trim connector made from nylon-66. Wire Management - Wires shall be taken into the system through cable ducts from the junction boxes and it is carried upto the panels through concealed conduits inside the blocks. Wires runs through the system from Bottom tile and extended to the top at various locations by the help of 2 nos. vertical Cable Ducts in each panels. Cable duct shall be made from 0.8 mm thick M.S. CRCA Grade D as per IS: 513 - 1994. It is constructed with two parts, one is body & another is cover. It holds the cables & gives aesthetic appearance by covering all cables entry, which are moving upward to the panels. Size of Cable duct is 107mm W X 154 mm H X 21 mm D.legs - Metal powder coated legs at the end. System shall also have 120 mm high powder coated standalone panel legs to give the system an elevated look. Single side legs are fabricated by CO2 welded MS Tube of section 38 mm x 25 mm (IS: 7138 ERW

Tube, 38 mm x 25 mm x 16bg) with the base plate of the MS plate of 35x22x5mm (IS: 2062, 5 mm HR) over which an M8 Leveler is fitted. Worksurface : Worktop of Size : 1500 mm(W1) x 1500 mm(W2) x 600mm(D) . Worktop shall be made out of 25mm thick prelam particle board. All the open edges of work surface shall be provided with machine pressed 2 mm thick PVC lipping glued with hot melt EVA glue. The work surface shall be provided with circular cut out of Dia.65mm as per the requirement, for passing of wires. These cut outs shall be provided with ABS covers. Worksurfaces are fitted to the panels by worksurface brackets. Brackets are made of 2.0mm thick CRCA grade D steel as per IS : 513-19. Brackets are slid in between end trim and vertical extrusions. Mobile Pedestal : Mobile Drawer Unit having 3 Drawers Unit having flat metal front and top with Central locking. The Drawer Unit consistes of 2Box and 1File Drawers. The Overall size of the Drawer Units is 450mm(W) X 435mm(D) X 646mm(H). Construction & Material of Drawer Unit : Welded Assembled of 0.8 thick CRCA for Body Shell, Drawer Front & tray, Front Side Stiffener, Rear Side Stiffener & Bottom, 1.2 thk CRCA Top Stiffener & Bottom stiffener. Drawer Fronts & Metal Front

Straight Edge. All Drawers with Double extension precision ball slide shall be provided. For Drawer pulling, side wise tapered recess provided in shell behind Drawer Fronts. Locking:10 lever Cam Lock & Central RH locking with actuator & lock channel mechanism. Top Panel : 0.8 Thk Metal Straight Edge Top. Castors : Swiveling non-lockable 4Nos Castors mounted below the body shell. The Total drawer unit is finished with Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10). Key Board Pullout Tray : Supplying and Fixing of sliding computer key board tray of 480mm (L) X 280mm (D) X 40mm(H) made out of CRCA steel as per IS : 513I made of 0.9mm thick powder coated with sliding channels and other fixing fittings. It should also have a sliding system for accomodating mouse.CPU Trolley : Supplying and Fixing of CPU Trolley of Size - 345mm(W) x 226(D) x 180mm(H) is made of 1.0 mm thick MS CRCA Sheet and Side support is made of 0.8 mm thick MS CRCA Sheet. It consists of 4Nos Non-lockable twin wheel castors are injection molded in Black Nylon. Comapny should be Greengard, BIFMA and AIOTA certified. Product should be BIFMA Level3 certifed certified.Wish Penta 1500 mm(W1) x 1500 mm(W2) x 600mm(D). Refer Annexure- 3 for prototype

Head Table 2100mm x 900mm with ERU 1200mm, MAIN DESK-Work Surface-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Gromet provided on work surface for wire management.Modesty Panel-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconfirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Under-structure-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeonfirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Hinge DoorStorage-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconfirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Handle is provided for ease of opening.Storage is provided with cam lock for security. Integrated Pedestal -Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconfirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Drawer fronts made of 25mm thickMDF one side pre-laminate board confirming toIS-14587:1998 with 0.4mm PVC membrane pressed on to topPedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metalPanel Drawer Slides. Drawer extension is 325 MM.Drawers have a soft closing & anti slam mechanism.Handles are provided for ease of opening.Pedestal is provided with lock for security. Size 2100Wx2250Dx750H. Refer Annexure-3 for prototype

BACK UNIT -Top Panel-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Slide Door Unit-Made of 25mm Thick Pre-laminated twin board of E1-P2grade and approved shadeconfirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side, bottom,back and shelves.Shutters are made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Shutters have a soft closing & anti slam mechanism.Handles are provided for ease of opening.Storage is provided with lock for security.Display/StorageUnit-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for bodypanels like side,back and shelves. Doors are made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Top panel of display unit Made of 25mm thick MDF one side pre-laminate boardconfirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. SIZE1800Wx500Dx1800H.Refer Annexure- 3 for prototype

Supplying and placing in position chair of the following specifications. The cushioned seat assembly shall consists of insert moulded polyurethane foam upholstered with foam laminated mesh fabric. the insert moulded foam is assembeled over a load bearing plastic seat cover. The back shallmade up of two piece injection moulded frame. The inner frame shall be upholstered with mesh fabric and mounted on the main assembly. Size of back shall be (W)-48.5cm, (H)-62.0cm & size of seat shall be (W)-51.0cm x (D)-52.5cm.armrest shall be injection moulded with height adjustable up to 4.5+/-0.5cm in 3 steps and width adjustable up to 20mm. The mechanism of chair shall have following features:360 degree revolving type, Front pivot Synchro mechanism, Tilt tension adjustment, 3 position tilt limiter with Anti-Shock feature. Spine bracket shall made of Aluminium diecast piece connecting back with mechanism. Neck rest assembly shall made up of polyurethane foam upholstered with foam laminated mesh fabric.

The neck rest assembly is mounted on the top of back. it can be adjusted up to 4.5+/-0.5cm up-down and has regular adjustment of 30 degree +/-2 . The chair shall be provided with pneumatic height adjustment which shall have stroke of 9.0 +/- 0.3 cm. The pedestal shall be made of die-cast polished.Refer Annexure- 3 for prototype

Supplying and Placing 3 seater sofa. The seat is made of PU foam with Density 28± 2 kg/cu.mtr having an additional top layer of super soft PU foam in Density 32 ± 2 kg/cu. upholstered with fabric or leatherette. The back is made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood (moisture resistance & termite proof) & pinewood of cross section devoid of major knots & surface defects 6 nos. per seat & 3.8 mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose 6 nos. per seat & 3.8 mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose.

It is a welded assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap. (W) 1460 (D) 905(H) 855 mm seat (H) 450 mm. Color as per approval prior to procurement. The company should ISO 9001, ISO 18001, ISO 14001, BIFMA, Greenguard-UL and AIOTA Certified.Refer Annexure- 3 for prototype

Supplying and Placing 2 seater sofa. The seat is made of PU foam with Density 28± 2 kg/cu.mtr having an additional top layer of super soft PU foam in Density 32 ± 2 kg/cu. upholstered with fabric or leatherette. The back is made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood (moisture resistance & termite proof) & pinewood of cross section devoid of major knots & surface defects 6 nos. per seat & 3.8 mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose 6 nos. per seat & 3.8 mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. It is a welded assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap. (W) 1460 (D) 905(H) 855 mm seat (H) 450 mm. Color as per approval prior to procurement. The company should ISO 9001, ISO 18001, ISO 14001, BIFMA, Greenguard-UL and AIOTA Certified. Refer Annexure- 3 for prototype

Supplying and Placing in place of 1 seater sofa. The overall dimensions of the sofa shall be 860W x 905D x 855H. The seat should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU foam with Density 32 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and termite proof as per IS:303.) and pinewood of cross section deviod of major knots and surface defects 6 nos. per seat and 3.8mm dia. zigzag spring assembly is mounted over understrucrure for cushioning effect. It should be a welded assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap. The company should ISO 9001, ISO 18001, ISO 14001, BIFMA, Greenguard-UL and AIOTA Certified.Refer Annexure- 3 for prototype

Supplying and placing in position center table of the following specifications. Glass shall be 12+/-0.3mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade for fixing with understructure. It shall be a welded assembly made in SS202 grade having dia. 12+/-0.04 as per IS:1762. overall dimensions of table shall be Width of table= 112.0 cm, Depth=60.0 cm, height=35.1 cm. The company should ISO 9001, ISO 18001, ISO 14001, BIFMA, Greenguard-UL and AIOTA Certified. Refer Annexure- 3 for prototype

Supplying and placing in position side table of the following specifications. Glass shall be 12+/-0.3mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade for fixing with understructure. It shall be a welded assembly made in SS202 grade having dia. 12+/-0.04 as per IS:1762. overall dimensions of table shall be Width of table= 60.0 cm, Depth=60.0 cm, height=35.1 cm. The company should ISO 9001, ISO 18001, ISO 14001, BIFMA, Greenguard-UL and AIOTA Certified. Refer Annexure- 3 for prototype

Supplying and placing in position Conference table of the following specifications. 6 Seater Boat Convex size shall be 2100 Width mm x 1200 Depth mm x 750 Height mm . Top shall be 32 mm thick base material shall be 18 plus 12 mm MDF board 0.4 mm PVC membrane foil using wrap around technology . The foil is pre- coated with PU layer for better scratch and wear resistant plus 0.6 mm balancing laminate on bottom surface . The veil and cross member shall be 18 mm thick base material shall be 16 mm plain particle board post laminated with 0.6 mm top laminate on either side plus 2 mm thick and 0.8 mm thick PVC edge banding . The legs shall be made from 1.6 mm matt silver anodized aluminium extrusion .Legs assembeled together with a plastic glide holder at bottom and 5 mm thick MS powder coated sheet at top . Also there shall be accessflap and switch mounting tray made from matt anodized aluminium extrusion . The company should ISO 9001, ISO 18001, ISO 14001, BIFMA, Greenguard-UL and AIOTA Certified.Refer Annexure- 3 for prototype

Providing and placing in position Topaz table with ERUPrimary Work Surface-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Softclosing access flap with in-build power box are provided on work surface for wire management.Secondary Work Surface-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Modesty Panel-Made of 25mm thick MDF-one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Under- structure-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Integrated Pedestal-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990,

Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF-one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to topPedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM.Drawers have a soft closing & anti slam mechanism.Handles are provided for ease of opening.Pedestal is provided with lock for security. Certifications: The company should ISO 9001, ISO 18001, ISO 14001, BIFMA, Greenguard-UL and AIOTA Certified. The company should ISO 9001, ISO 18001, ISO 14001, BIFMA, Greenguard-UL and AIOTA Certified. Table Size 1800 x 900 with Side Unit 1200mm.Refer Annexure- 3 for prototype

Supplying and placing in position chair of the following specifications.The seat shall be made up of 1 .4 +/- 0.1 cm thick hot pressed plywood uphostered with fabric and moulded polyurethane foam. The back is made up of injection moulded glass filled nylon & upholstered using fabric mesh with high tenacity yarn. The back assembly should have an height adjustable lumbar support pad having adjustment of 5.0+/-0.5cm. The dimensions of seat should be 49.5cm(W) x 51.8 cm(D) and that of back should be 4.50cm(W) x 57.5cm(D). Height Adjustable Armrest shall be made up of polypropylene and shall have swivel as well as to & fro motion, it shall have moulded PU top and height can be adjusted upto 6.0 +/- 0.1 cm. The mechanism of the chair shall have following features : 360⁰ revolving type, Centre Tilt Syncro, 4 position locking. The chair shall be provided chrme plated pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall be made of injection moulded nylon. it shall be fitted with 5 nos twin wheel castor.

The size of the pedestal shall be 66.0 +/- 0.5 cm pitch-centre-dia (76.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black plymer. Overall dimensions of Chair shall be, Width of Chair - 76. cm, Depth of Chair - 76. cm as measured from pedestal below. Height of back from ground - min 95.5 to max 105.5cm. Seat height - min 43.5 to max 54.0cm. Dimensions tolerance / variations shall be within +/- 1 cm. The company should ISO 9001, ISO 18001, ISO 14001, BIFMA, Greenguard-UL and AIOTA Certified. Refer Annexure- 3 for prototype

Supplying and placing in position chair of the following specifications.The seat shall be made up of 1 .4 +/- 0.1 cm thick hot pressed plywood uphostered with fabric and moulded polyurethane foam. The back is made up of injection moulded glass filled nylon & upholstered using fabric mesh with high tenacity yarn. The back assembly should have an height adjustable lumbar support pad having adjustment of 5.0+/-0.5cm. The dimensions of seat should be 49.5cm(W) x 51.8 cm(D) and that of back should be 4.50cm(W) x 57.5cm(D). Height Adjustable Armrest shall be made up of polypropylene and shall have swivel as well as to & fro motion, it shall have moulded PU top and height can be adjusted upto 6.0 +/- 0.1 cm. The mechanism of the chair shall have following features : 360⁰ revolving type, Centre Tilt Syncro, 4 position locking. The chair shall be provided chrme plated pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall be made of injection moulded nylon. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 66.0 +/- 0.5 cm pitch-centre-dia (76.0 +/- 1.0 cm with castors).

The twin wheel castors shall be injection moulded in black plymer. Overall dimensions of Chair shall be, Width of Chair - 76. cm, Depth of Chair - 76. cm as measured from pedestal below. Height of back from ground - min 95.5 to max 105.5cm. Seat height - min 43.5 to max 54.0cm. Dimensions tolerance / variations shall be within +/- 1 cm. The company should ISO 9001, ISO 18001, ISO 14001, BIFMA, Greenguard-UL and AIOTA Certified.Refer Annexure- 3 for prototype

Providing & placing in position metal storage unit consists of Floor Storage units. These units shall be stacked widthwise to form a row of storages. The construction of the storage units shall be aesthetically appealing and completely knock down. Legs shall be fitted in the floor units with screw type leveller and material shall be from combination of CRCA sheet of 0.5mm & 0.8mm thick. The storage units shall be provided with height wise adjustable shelves mounting , each full shelf shall have a load capacity of 40 kg Uniforming Distributed Load. The complete floor units shall be provided with 3 way locking and Finished with Epoxy Powder coated to the thickness of 50 microns(+/-10). All hardware shall be of reputed make/brand e.g. Hettich/Haffelle/Dorma as per sample finally approved by the department.The company should ISO 9001, ISO 18001, ISO 14001, BIFMA, Greenguard-UL and AIOTA Certified. of Size 2025Hx450Wx500Dmm.Refer Annexure- 3 for prototype

Sub-Head: IV ELECTRICAL WORK

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required.

Group C

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Supplying and fixing following size modules, GI box along with modular base & cover plate for modular switches, sockets & electronic fan regulator in recess etc. as required.

1 or 2 Module ( 75 mm x 75 mm )

8 Module ( 125 mm x 125 mm )

Supplying and fixing following modular switch / socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

5 / 6 amps switch

3 pin 5/6 amp socket outlet

Telephone socket outlet (RJ 11 single with shutter)

Modular type blanking plate

TV antenna socket outlet

Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32amps 240 volts “C” curve DP MCB complete with connections, testing and commissioning etc. as required.

Supplying and fixing call bell / buzzer suitable for single phase, 230 V, complete as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

4 X 2.5 sq. mm + 2 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

4 X 4 sq. mm + 2 X 4 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

4 X 6 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing of modular RJ 45 (Modem Jack) CAT6 I/O socket outlet on the modular single socket face plate and plastic gang box including connections complete etc. as required.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface / recessed steel / PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying, installation, testing and commissioning of Passive Infrared (PIR) technology based occupancy sensor having high performance, non regulating programmable type, suitable for connected load upto 10 amp, for mounting height upto 2.8 mtr and for 5 m diameter coverage area along with necessary fixing arrangements i/c programming at site etc. complete as required.

Supplying of following 220 V , 50 Hz Energy efficient recessed mounting direct / indirect high performance decorative LED luminaire / fittings in false ceiling / surface mounted, with all required frame, drivers, accessories etc. complete in all respect. (Make : Philips / Wipro)

2' x2' Recessed Mounted LED flat panel 220 V, 50 Hz LED Light Fitting complete with Cool White light of model RC365B LED33-6500 PSU OD WH (Philips) OR CRCO10R038HP65GL1 (Wipro)

2' x2' Surface Mounted LED flat panel 220 V-240V, 50 Hz LED Light Fitting complete with Cool White light of model SM365C LED32-6500 PSU OD WH (Philips) OR CRCO10R038HP65GL1 (Wipro)

Down lighter LED (Round) 220 V, 50 Hz light Fitting with Cool White light DN 191B LED 6S 6500 PSU WH S1 (Philips) OR CRDL11R017HP65 (Wipro).

Astra Spot 3 watt LED COB white Down light (Round) 240 V, 50 Hz (Philips) OR Garnet 3W white round LED Spotlight (Wipro)

Tarang Bright 20 Watt LED Batten ( Cool Day Light ) 240 V, 50 Hz, Fitting (Philips) OR Garnet 22W LED Batten (Wipro)

31402 Muziris 7W Picture light LED warm white (Philips)

Decorative Wall Bracket LED Light Fitting 8W Aristro LHJE01106499 (Havells)

Surface mounted LED luminaire with diffused optics SM270C LED 30S 6500 PSU WH (Philips) OR CRCO13S038HP65G1 (Wipro)

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent/ LED panel fitting of all types complete with all accessories including chain etc. and tube / lamps etc. directly on ceiling / wall including connection with 1.5 Sq.mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS /CFL /LED lamps per fitting, complete with all accessories including connections etc. as required.

SITC of LED Cove light Strip with driver complete etc as required. (make : Philips Linea OR Wipro Garnet)

Supplying, installation, testing & commissioning of High Flo Wall Mounting Fan (white) with regulator of 400 mm sweep 230V, 50 Hz AC with oscilation on wall / wood with the help of rawl plug and screws including connections etc complete in all respect.

Supply of heavy duty exhaust fan of 300 mm sweep, 900/1400 rpm, single phase complete with all accessories including their connections & testing etc complete in all respect.

Supply of heavy duty (Industrial) exhaust fan of 450 mm sweep, 900/1400 rpm, single phase complete with all accessories including their connections & testing etc complete in all respect.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.

Upto 450 mm sweep

Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.

SITC of ABS PLASTIC Automatic Hand Dryer (White) 1 Phase, 1800 W, 200 - 240 V , 50 Hz, Dry Hand Time : 15-20 Seconds etc complete as required. (Make : Dolphy)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single pole

Single pole and neutral

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

8 way (4 + 24), Double door

Supplying and fixing 63 amp, 10 KA TPN "C" curve MCB, 415 V, in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing TPN sheet steel enclosure on surface/ recess along with 63 amps, 10 KA, 415 V “C” curve TPN MCB complete with connections, testing and commissioning etc. as required.

Providing and fixing sheet steel enclosure suitable for 125 amps. TPN MCCB, cable incoming and outgoung connection having space for loop cable and shall be fabricated from 2.0 mm thick CRCA sheet steel including powder coated painting etc. complete as required.

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, after removing existing MCCB,etc. as required.

125 A,36KA,FPMCCB

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/submain wiring/ cable as required.

Supplying of following size Aluminium armoured XLPE / PVC insulated and PVC sheathed cable of 1.1 KV grade.

3.5 core x 25 sqmm size

3.5 core x 35 sqmm size

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size on wall surface / recess including cutting the wall and making good the same in case of recessed cable

Upto 35 sq. mm (clamped with 1mm thick saddle)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required.

3½ X 25 sq. mm (28 mm)

3½ X 35 sq. mm (32mm)

Supplying and drawing of 4 x 16 sq mm FRLS PVC insulated copper conductor, Single Core Heavy Duty Copper Cable in the existing surface/ recessed steel/ PVC conduit including connections with copper lugs etc complete as required.

Dismantling of existing bullet / dome type cameras (approximate 10 cameras) with all accessories, video / audio / LAN & supply cable and re-installation the same with cable drawing in existing PVC pipe etc. complete in all respect.

Rewiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable and 1.5 sq.mm FRLS PVC insulated copper conductor single core cable as earth wire in existing surface/recessed steel/PVC conduit including dismantling as required. Group C

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.

(a) 3 x 1.5 sqmm

(b) 3 x 2.5 sqmm

Supplying and fixing 3 Pin, 5 A Ceiling rose on the existing junction box / wooden block including connections etc as required.

Supply, Installation, testing and commissioning of following size Android LED Smart TV with USB Port, HDMI Port including Heavy Duty Wall Mount Bracket / Stand, connections etc complete as required. Make :- Samsung / LG / Sony

32 Inches Android LED Smart TV

43 Inches Android LED Smart TV

55 Inches Android LED Smart TV

Supplying, installation, testing and commissioning of 25 Liters Storage water Vertical Mounting Type Geyser 2 KW, 230 V, Single Phase (4/5 STAR Rating) including inlet & outlet water pipe connections etc complete in all respect. Make : Crompton,Venus, Recold, Havells)

Disconnecting & dismantling of existing flourescent fitting, PL fittings, Mirror fittings, Piano type & Modular type switch, socket boards, DP MCB box, LAN, Telephone socket,Industrial box, DB's, Wall bracket, Ceiling fans, Wall fans, Exhaust fans & Geyeser etc. including wiring etc. complete as required.

Salvage value of following dismantaling material "As is where is basis".

2 X 36/40W recessed type Fluorescent Tube light fitting including wiring

2 X 36/40W surface type Fluorescent Tube light fitting including wiring

1 X 36/40W box type Fluorescent Tube light fitting including wiring

2 X 36W 2'x2'PL recessed type light fitting including wiring

Wall bracket light fitting including wiring

Mirror light including wiring

1 no. 5/6 amps piano type Switch & 1 no. 5/6 amps. Piano type socket board including wiring

2 no. 5/6 amps piano type Switch & 2 no. 5/6 amps. Piano type socket board including wiring

4 no. 5/6 amps piano type Switch & 4 no. 5/6 amps. Piano type socket board including wiring

1 no. 15/16 amps piano type Switch & 1 no. 15/16 amps. Piano type socket board including wiring

2 no. 15/16 amps piano type Switch & 2 no. 15/16 amps. Piano type socket board including wiring

1 no. 15/16 amps moduler type Switch & 3 no. 15/16 amps. moduler type socket board including wiring

Ceiling fan 1200 mm sweep including wiring & down rod

Exhaust fan 300 mm sweep including wiring

Exhaust fan 450 mm sweep including wiring

Wall mounting fan 400 mm sweep including wiring

DP MCB upto 32 amps. With steel/PVC enclouser including wiring

Industrial box with SP MCB upto 32 amps. Including wiring

Geyser 25 ltr.

Geyser 35 ltr.

Sub-Head: III EPABX SYSTEM

Supplying, installation, testing and commissioning of 100 pairs Main Distribution Frame (MDF) box with Krone module and frame etc complete in all respect.

Supplying, installation, testing and commissioning of Digital IP based EPABX system for 6 X 96 Lines (102 Lines) with one 24 Key Digital Phone / Operator console etc complete in all respect. Make :- NEC / Matrix / Panasonic

Sub-Head: IV FIRE DETECTION AND ALARM SYSTEM

Supplying, Installation, testing and commissioning 4 ZONE Microprocessor Based Main Fire Alarm Control Panel complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections, wall mounted type fabricated out of 1.6 mm CRCA sheet, dust and vermin proof, power coated, solid-state sector control panel made in standard cabinet with Zone healthy, isolate, healthy, short , open , fire signal, visual test mode, suitable for operation 220 volts AC power supply / 24 V DC output, automatic battery charger, 24 volts maintenance free batteries sufficient for 30 Minutes during an emergency conditions etc. complete in all respect.

Supplying, installation, testing & commissioning of heat detector operating at 54ºC/57ºC with rate of rise cum fixed temperature (dual thermistor) type with mounting base complete with all connection etc. as required.

Supplying, installation, testing & commissioning of smoke detector with builtin LED and mounting base complete with all connections etc. as required.

Supplying, installation, testing & commissioning of manual call boxes of MS construction in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required.

Supplying, installation, testing & commissioning response indicator on surface/recess MS box having two LEDs metallic cover complete with all connections etc. as required.

Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required.

Supplying & laying following size fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.

(a) 2 x 1.5 sqmm

(b) 3 x 1.5 sqmm

Disconnecting & dismantling of existing 4 zone Main Fire Alarm Control Panel, smoke / heat detector, manual call box, Responce indicator and hooter including wiring etc. complete as required.

Salvage value of following dismantaling material "As is where is basis".

Heat / smoke detector

Response Indicator (RI)

Hooter

Manual Call Box (MCB)

4 zone Main Fire Alarm Control Panel

Sub-Head: V AIR CONDITIONING SYSTEM

Supply of following capacity Single phase, 230 V, 50 Hz Air Ccooled Micro Cool Cassette Type Air-Conditioner (Ceiling Mounted) with energy efficient rotary compressor and microprocessor based logic control alongwith vibration pads for indoor unit, pressure testing, vacuuming, eco-friendly refrigerant gas charging, 100 % copper coil for indoor & outdoor units as per manufacturing technical specifications.

(a) 1.5 TR Star rating: 3

(b) 2.0 TR Star rating: 3

Installation, testing and commissioning of IDU & ODU up to 2.0 TR Cassette Type (Ceiling Mounted) Air-Conditioner unit with necessary supports & fittings, pressure testing of copper pipes with nitrogen, vaccumising the system, internal wiring & drain leak test, testing and commissioning of units etc. complete as required.

Supply and fixing of 25 mm dia PVC hard drain pipe for above said cassette type air-conditioner units etc. complete as required. (Note :- Drain pipe dowm from First floor to ground level approximate 10 meter height)

Supplying and fixing of suitable size additional copper refrigerent pipe up to 2.0 TR cassette type air-conditioner unit with proper insulation including control wiring, power cable for interconnection of outdoor unit and indoor unit and drain pipe with insulation, accessories etc complete as required.

Supplying, fabrication and fixing of suitable size MS angles frame for 2.0 TR Cassette Type air-conditioner unit duly painted for the above mentioned outdoor units etc complete as required. Note :- Outdoor units installed approximate 10 meter height from ground level)

Supplying and drawing of 3 core x 4 sq mm FRLS PVC insulated & Sheathed Copper Flexible Cable in the existing surface/ recessed steel/ PVC conduit including connections with copper lugs etc complete as required.

Disconnecting & dismantling of existing Window type and split type AC units upto 2.0 TR including wiring, copper pipe, drain pipe & all related accessories etc. complete as required.

Salvage value of following dismantaling material "As is where is basis".

Salvage value of dismentled old all make / model Window Type Air-Conditioner upto 2.0 TR " As is where is basis"

Salvage value of dismentled old all make / model Split Type Air-Conditioner upto 2.0 TR including wiring, copper pipe, drain pipe & all related accessories" As is where is basis"

CREATORS ENGINEERS AND INTERIORS

Leo Air and Power Solution Pvt Ltd.,

Rakesh Kumar Engineers and Contractor

GRID INTERIORS PVT LTD

Mahendru Consultants

VirenderKumarAndCo

Agarwal Associates

The Creators

KRISHNA REFRIGERATION

S P CONSTRUCTION